Search Documents

By R W. Bellenie, P N. Blakey

The phenomena of post detonation gases in muckpiles is reasonably well known. It causes the 'rumbling' noises occasionally heard after a blast in open pits or quarries and is thought to occur due to initiation of carbon monoxide, hydrogen, etc. by 'hot' spots within the muckpile. The problem usually occurs with highly aluminized products, but can occur with any oxygen deficient product. This phenomenon was never a problem underground due to restriction on access to blast areas, ventilation criteria, etc. until the advent of large diameter blastholes and particularly their use for specialized applications such as drilling for blasting down 'hang-ups' in ore passes.

Jan 1, 1980

By S. D. Thompson

An AIME transaction by P.L. Allsman (1960), "Analysis of Explosive Action in Breaking Rock," contains many useful concepts applicable to blast design. Of special interest was the derivation of a heave blasting burden formula, which is important in establishing the maximum burden. Unfortunately, its derivation contains a fundamental error and then a compensating one. This formula was: [ ] The derivation used the impulse-momentum principle, with a 0.3 m thick (1 ft thick) radius of rock mass being acted on by an explosive impulse. However, the rock weight was not converted to mass by dividing by the gravitational constant. This mistake can be verified by checking the units in the formula, which resolve into m%-sec instead of meters. Adding the gravitational constant corrects this: [ ] If the minimum velocity is now taken as 0.3 m/sec (1 ft per sec), as was recommended, excessively large burdens result. Any appropriate rock velocity should be capable of throwing the rock mass a minimum distance so that the swell needed for breakage can occur. Unless the burden is extremely small and the bench height is very high, it is unlikely that a velocity of only 0.3 m/sec (1 ft per sec) will be sufficient. A review of the literature indicates that average rock velocities observed by camera studies typically range from 15 to 30 m/sec (50 to 100 ft per sec) (duPont deNemours and Co., 1977; Tansey, 1979). On this basis, a minimum rock velocity of about 15 m/sec (49 ft per sec) would be expected and not 0.3 m/sec (1 ft per sec). When a velocity of 15 m/sec (49 ft per sec) is inserted into the corrected formula, the results approximate those of the original formula with a velocity of 0.3 m/sec (1 ft per sec). The errors were approximately self-compensating [ ] References Allsman, P.L., 1960, "Analysis of Explosive Action in Breaking Rock," Transactions, AIME, Vol. 217, pp. 475-476. E. I. duPont deNemours and Co., 1977, Blasters' Handbook, 175th Anniversary Edition, Dupont, Wilmington, DE, pp. 233. Tansey, D.O., 1979, "The DuPont Sequential Blasting System," CIM Bulletin, Vol. 72, July, p. 80. Thompson, S.D., 1981, "Critical Review and Revision of Surface Blasting Practice," MS thesis, West Virginia University, pp. 308-316.

Jan 3, 1985

By Alfred H. Bell

Illinois produced 5 per cent more crude oil in 1934 than in 1933, because there was less curtailment, and. the value of the year's production at the wells was 35 per cent more than that of the previous year. The average price of Illinois crude oil in 1934 was $1.13 as compared with $0.87 in 1933, an increase of 30 per cent. The quotas of allowable production for Illinois during 1934, as authorized by Oil Administrator Harold L. Ickes, were as follows: January, February, March, 12,000 bbl. per day; April, May, 12,500; June, July, 12,600; August, 12,500; September, October, November, 12,000; December, 11,700. No other restrictions on production were in effect during the year until Oct. 11, when it was found necessary to prorate the fields to 75 per cent, a curtailment of 25 per cent below the quota fixed by the Federal Administrator. On Dec. 1 the curtailment was reduced to 18 per cent and on Dec. 18, to 15 per cent. Production in Illinois by months during 1934 was as follows: Barrels Barrels January...................... 393,000 July........................ 394,000 February.................... 337,000 August..................... 402,000 March....................... 394,000 September.................. 378,000 April......................... 373,000 October.................... 352,000 May......................... 411,000 November.................. 305,000 June......................... 392,000 December................... 321,000 Total ................... 4,452,000 In spite of higher prices for crude oil, fewer wells were drilled in Illinois in 1934 than in 1933 (Tables 1 and 2). Of the 26 wells drilled, 10 were oil producers, 8 were in proved fields and 2 were in a new pool in Wabash County, l½ miles south of the nearest production, one was a small gas well on the Stubblefield anticline in Bond County, one was an input well for repressuring in the Colmar-Plymouth field, McDonough County, and 14 were dry holes, mostly scattered wildcat tests.

Jan 1, 1935

Three complete connector assemblies and six separate contacts were submitted to a series of tests to establish the connectors permissibility and compliance with U. S. Bureau of Mines research Contract #H 0110423 D.C. portion. Test Procedure TPC-0118 was coordinated, and the test plan approved by the Bureau as fully complying with the intent of the contract for the direct current connectors. The components and connector assemblies have been demonstrated in testing that they meet or exceed all the requirements of the test procedure.

Jan 1, 1974

By V. Petr, G. G. W. Mustoe, T. G. Rozgonyi

We introduced a numerical method that is applicable for the analysis of static and dynamic deformations of elastic media. In this numerical study, each elastic body is modeled with a system of several hundred rigid particles that are joined together elastically. Maximum shear stress fields due to external loading are obtained and compared with those obtained by photoelastic experiment. Preliminary results are presented for the stresses generated in circular disk shaped bodies idealized with connected systems of particles. Extension of this simulation method to fragmentation of brittle materials is also illustrated in an example.

Jan 1, 2000

By A. Adiaddevich

Petroleum has been found in Russia in various localities from north to south, as may be seen from the list given below: (a) In the basin of the Petchora river, Northern Russia. (b) In the basin of the Volga river, in the governments of Samara and Saratoff. (c) In the government of Astrakhan and in the Uralsk territory, close to the northern and eastern coast of the Caspian sea. (d) At Grozny in Northeastern Caucasus. (e) In the Daghestan territory, Eastern Caucasus, on the Caspian sea. (f) On the Apsheron peninsula (Baku and other districts) close to the Caspian sea shore. (g) On the island of Tcheleken in the caspiah sea, also on the island of Sviatoi. (h) In the Transcaspian territory on the Neftianaia Gora (Oil hill) and on the surrounding hills. (i) In the Ferghana valley in Russian Central Asia. (j) On the Kertch-and Taman peninsulas on the Black sea. (k) In Siberia it has been discovered in the Transbaikal territory and on the island of Sakhalin.. ' ' In the above-mentioned districts petroleum has been found to exist under different geological conditions and to vary in its chemical and physical properties. At the present time petroleum is produced in Russia at Baku, Grozny, on the island of Tcheleken, in the Ferghana district, and in the Uralsk territory. The yearly production in 1912 throughout the Russian Empire amounted to 69,400,000 barrels, of which the Baku fields were responsible for 52,000,000 barrels. This shows that the Balm fields on the Apsheron peninsula are the chief oil-producing centers in Russia, being at the same time the oldest of all our oil fields. In this paper I shall discuss the Baku fields only, leaving all the others until a later date. The Apsheron peninsula in the Eastern Caucasus protrudes into the Caspian sea in the shape of a triangle some 47 miles long covering a total area of some 750 square miles. The eastern part of the peninsula is a flat, slightly rolling plain, rising in its highest parts to 140 to 170 ft. above

Jan 1, 1915

By Towsey C. A

Significant advances in regional geochemical exploration techniques have been made over the last 5 years in the search for gold deposits. This has occurred largely by the development of the bulk cyanide ex- tractable gold (BLEG) also known as the Bulk Cyanide Leach (BCL) tech- nique. The technique has been developed and designed for Australian conditions and has two main ad- vantages over the pan concentrate technique preferred by many ex- plorationalists, viz:,. 1. It is designed to collect ultra fine gold common to epithermal and other north Queensland types of gold deposits. 2. The large sample (approx.5 kg) allows very low detection levels, ranging between 0.1 and 0.05 ppb Au. The use of the BLEG technique in exploration has led to the discovery of the Wirralie gold deposit and numerous other epithermal gold prospects previously undetected by pan concentrate and minus 80 mesh (pathfinder elements) surveys in the Drummond Basin.

Jan 1, 1989

By L. Guttman

LESTER GUTTMAN* The question of whether classical thermodynamics alone imposes any lower limit to solid solubilities was raised during a discussion among various members of the Institute for the Study of Metals. Although our conclusions are not new,1 they may be worth reiterating, since confusion on this subject seems to persist. In a binary system (A,B), the conditions for equilibrium, at constant pressure and temperature, between a solid solution and a liquid solution are µAs = µAl [la] µBs = µbl [lb] Here µ denotes the chemical potential either of component A or B, as shown by the subscripts, and the superscripts s and l refer to the solid and liquid solutions, respectively. These two conditions are just sufficient to determine the compositions of both phases. Suppose, however, that the solid phase is found experimentally not to contain any of component B; then we cannot evaluate µbs, which is defined by Here nAs and nBs are the number of mols of A and B, respectively, in the solid, whose free energy is Fs. Eq lb cannot be used, but it is no longer needed: we stated at the outset that the solid has the composition "pure A," and only the liquid composition need now be determined, from Eq la. All the equilibrium properties of the system can be derived from Eq la rigorously and simply. Hence there is no purely thermodynamic reason to exclude phase diagrams which show precisely zero solid solubility. Marsh2 has objected to such diagrams as implying that even the transformation of pure A begins at the eutectic temperature. In any case, the user of the diagram must have a certain minimum knowledge of how to interpret it, and it would seem simpler to remember the general rule that eutectic temperatures have no significance for pure components, rather than to show, say, by broken lines, on a scale which will often be exaggerated, a hypothetical solid-solubility about which we know only that it is less than a certain amount. The case of an intermetallic compound in equilibrium with a binary liquid solution does not require a separate treatment since nothing in the foregoing was dependent on the nature of the components. Therefore, thermodynamics alone does not exclude the possibility that (intermetallic) compounds may exist with compositions always precisely those given by their chemical formulas. With the aid of extra-thermodynamic methods, one may conclude that the solubility of one solid in another is never exactly zero. On the other hand, one would generally expect that the solubility will be small unless the components resemble one another (as do the metals), or form weakly-bound crystals. Therefore, it is useful to know that when there is no direct evidence for solid-solubility, one may neglect it without violating thermodynamic principles.

Jan 1, 1950

By F. L. Wilke

A model is presented to minimize the winning costs per shift within the different sections of a potassium mine by liner programming and to simulate the other areas to get all costs in order to comp re different production strategies. he model is based on a a given total layout of the underground mining which is considered to be fix during the planning period. Room-and-pillar mining is assumed to be used. Potassium extraction is done by drilling and blasting. Transportation of the raw material to sectional crushers is done by scoop-trams where it is crushed to coarse-grains which allow further transportation by conveyor belts to the hoisting shaft or to a bunker. When production is stopped, the continuously working factory is supplied by means of this bunker. Starting from a desired composition of the raw material the model has to keep the given total. demand of raw material per shift, to minimize the winning costs, to keep the capacity constraints of the equipment and to determine the planned output of production of the sections per shift. Costs of the areas which follow the extractions are added to extraction costs in order to allow a comparision of costs of several alternatives of production. Optimization in extraction and assignment of scoop-trams to sections is done by linear programming. The other areas of the mine are treated by simulation. The model output is a schedule of the calculated costs broken down into costs of processes, equipment, and kinds of costs. This proceeding enables to compare different ways of production.

Jan 1, 1979

By Shengli Yang

Solid backfill mining, as a green mining technology, has the advantages of a higher resource recovery, less damage to the environment and the ability to dispose of waste underground. It has been applied successfully in the Xingtai and Xinwen mining areas in China. Strata behavior and the movement of overburden strata in this mining method are very different from fully mechanized longwall mining, which results in a natural caving, because the gob is filled with waste rock, fly ash and other backfill material. The results of field measurements showed that the periodic weighting interval of the main roof is longer; the magnitude of periodic weighting is smaller; the peak and zone of influence of the front abutment pressure are smaller than those in fully mechanized mining; that major deformation of mine roadways occurs within the influence zones of the abutment pressures; that the falling space of immediate roof is smaller, with the lower portion falling more sufficiently than the upper; that the main roof subsides slowly; and that the falling height of the overlying strata is greatly reduced.

Jan 1, 2011

The No. 2 Ore-shaft, at Mount Isa Mines Limited, involving the use of boreholes as ropeways for the upper portion thereof, constitutes, we believe, a unique feature in hoisting installations. The boreholes were sunk from the surface to a depth of 390 ft., thus eliminating the necessity of erecting the hoist at an underground location or construction of the shaft for this distance. Fig. 1, a diagrammatic cross-section through the shaft, shows the complete installation from the surface down to the first loading station below No. 7 haulage level.During the latter part of 1936, conditions encountered in sinking the Main Ore shaft made it impracticable and uneconomical to continue deepening it to serve haulage levels below the present No. 5-level. Plans were therefore made for an interior shaft, to serve new lower levels, that terminated above No. 5-level so that ore hoisted could be drawn off on this level and transported to the Main Ore shaft for final conveyance to the mill crude ore bin.Referring again to Fig. 1, it is apparent that the section above No. 4-level, if opened out to full shaft size, would be inoperative and would serve no useful purpose except, possibly, as a ventilation duct. Original plans therefore did not include continuation of the shaft above No. 4-level. Excavation of a hoist room upon No. 5-level; erection of sheave wheels just below No. 4-level, and a long inclined ropeway leading from the hoist to the sheaves, were incorporated in the general layout. Work on the lower sectionof the shaft had started when the idea of locating the hoist...

Jan 1, 1939

Prior to any detailed discussion, I'd like to say that Dr. Aplan has made direct hits on two important considerations: 1) The most demanding need in Fine Coal research is to develop improved methods of sulfur reduction. 2) The areas of particle (impurity) liberation and froth flotation hold real near-term promise as techniques for improved sulfur removal. Digressing for a moment, I thin kwe can all remember the time when the biggest problem facing coal research was simply defined - "No money!" In the mid 70's we suddenly found ourselves dealing with a product worth five to seven times the value it carried in the mid60's. All of a sudden, we're talking about a high-profile, high- value commodity. The coal industry still hasn't made the complete psychological adjustment - especially in the operating areas (prep plants included). We have a valuable material at hand which is, in' many cases still being processed as though it were a two or three dollar per ton item. Simply put, I think that while the industry has made some major strides during this transition, a stronger commitment of attitude (and finances) needs to be made toward deeper definition of beneficiation work. Back to specifics - Dr. Aplan has really highlighted three areas where strong research efforts are needed. 1) Liberation processes - not limited to mechanical comminution - must be more fully studied.The industry certainly needs a better handle on value returned (improved ability to beneficiate) for dollars spent on improved liberation. 2) Flotation processes probably hold the most promise for near- term improvement in fine coal beneficiation technology. Dr. Aplan’s.

Jan 1, 1979

By W. White

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the author elect, he may distribute copies at the time of the Symposium.

Jan 1, 1986

By Julius Pohlman

The history of Niagara Falls, as currently told, is simple, and by that very simplicity it has been rendered plausible. AS the story runs, the Falls were once situated at Lewiston, 7 miles to the north of their present site; and, since all the rocks in this section are alternate hard and soft strata, the waters acting readily upon the soft shales caused their removal, and the overlying hard lagers, deprived of support, broke down under the weight of the large volume of water that rushed over them; and this erosive action has sent the edge of the fall more and more southward, until it now has excavated the seven-mile gorge between Lewiston and the village of Niagara Falls. (See Fig. 1.) As early as 1790" we find this theory advanced in a description of this region; and it has been practically endorsed by subsequent observers, the most prominent of whom was Prof. James Hall, the State Geologist of New York, who surveyed the Falls in 1841, and gave the most exact description of their surroundings in the publications of the State Survey.? Not until 1883 was the correctness of the accepted theory of the Falls questioned.‡ The geology of the basins of the Great. Lakes, as elucidated by Newberry,§ Speneer,ll and others, has added largely to a clearer understanding of the life-history of the Falls. The investigators have shown us that Lake Erie, as a lake, is, geologically speaking, quite young; that its valley was excavated in pre-glacial times by a series of rivers; and that the Maumee, Sandusky, Cuyaboga, Alleghany and other rivers carried the drainage of the surrounding

Jan 1, 1889

By Carla Lupi, Mauro Pasquali

"Photographic technology is based on light sensitivity of silver halides that, because of silver properties, are capable of forming photographic images. Photographic laboratories and hospital departments because of digital photographic systems less use this technology today. Nevertheless recovery of silver is still advantageous because environmental problems related to Ag ions danger to biological system. Many processes have been studied to treat silver containing photographic bath: cementation, chemical precipitation and electrowinning. In this work, after preliminary voltammetric tests, a batch electrometallurgical process has been studied to completely deplete the silver containing photographic fixing baths. The effect, of silver concentration in the electrolyte, varying over the range 0,2-1 g/L, bath stirring and current density ranging from 10 to 500 A/m2 on process yield and deposit quality, has been investigated. Introduction Photographic wastes, electronic scrap and spent catalysts constitute the main sources of materials for silver recycling. Among those silver secondary sources, the photographic discharged material could be still important and useful, even if photographic laboratories and hospital departments, because of digital photographic systems, less use photographic technology. Several processes have been developped in order to recover silver used in the field of photography from both photographic solutions and scrap film paper[1-5]. Fixing solutions are very complex baths but, because of silver position in the electromotive series, electrolysis could represent an advantageous method for silver recovery. Electrolysis produces high purity silver without generating new pollutants, while the fixer can be reused: obviously it is necessary to purge off a portion of this solution in order to avoid the excessive build up of other deleterious compounds into solution. A tested recovery method was constituted by the dissolution of silver from X-ray films with concentrated nitric acid. Internal electrolysis and external electrolysis methods were carried out using a steel electrode as cathode and a copper electrode as anode [6]. Silver recovery from photographic chemical solutions has been also performed in a special cell [7]: the solution is supplied to the bottom of a non-agitated cell having a vertically elongated form and including a central anode enclosed by a cathode. An other study discloses the use of an electrolytic cell comprising at least one anodic compartment and one cathodic compartment: the solution is treated in the cathodic compartment and then recycled in the anodic one [8]. A more recent work proposes the use of zirconium cathode for the recovery of silver from photographic fixing solution [9]: studies carried out by cyclic voltammetry showed that about 98% of total Ag can be recovered with an electrical efficiency close to 92%."

Jan 1, 2008

By Philip R. Whitney

Deposition of manganese oxides is of common occurrence in streams of the north-eastern United States. Manganese entering the stream in solution in ground water is oxidized and deposited in the stream, primarily as oxide coatings on detrital materials. Prevalence and thickness of the coatings increases with increasing particle size in the coarse sand and gravel range. A number of metals of economic and environmental interest are enriched in these coatings. Samples of 8 to 16 mm pebbles were obtained from two streams in the Shawangunk region of southeastern New York State, an area of know71 Pb/Zn/Cu mineralization. The pebbles were leached to remove the oxide coatings and the resulting solutions analyzed for Mn, Fe, Pb, Zn, Cd, Cu, Co, and Ni. Trace-metal/Mn ratios in these streams are generally one to two orders of magnitude higher than regional background values. Profiles of trace- metal/Mn ratios along the streams show considerable detail; contributions of metals from tributaries are sharply reflected in the metal content of the oxides. The potential advantages and disadvantages of using coated stream gravel for geochemical prospecting and environmental studies are discussed in the light of these and other data.

Jan 1, 1976

Research by the National Institute for Occupational Safety and Health (NIOSH) on multiple-seam mining has resulted in two new ground control products. Information Circular (IC) 9495 In some U.S. coalfields, particularly in central Appalachia and the West, most mines are operating above and/or beneath previously mined seams. The effects of multiple-seam interactions can include roof falls, rib spalling, and floor heave. These can seriously threaten the safety of miners and disrupt mining operations. Information Circular (IC) 9495 is a proceedings document containing a variety of papers that summarize recent knowledge about multiple-seam mining. A NIOSH study that analyzed case histories collected from 44 U.S. coal mines is described in detail. The study confirmed that overmining is much more difficult than undermining, and isolated remnant pillars cause more problems than gob-solid boundaries. The study's results were the basis for the Analysis of Multiple-Seam Stability (AMSS) software package. The proceedings also contain two papers describing the LaModel family of software. The original three-dimensional version of LaModel is essential for detailed analyses of complex multiple-seam scenarios. LaM2D implements a simplified, two-dimensional model suitable for quick approximations of the multiple-seam stresses and strains. Three papers in the proceedings focus on case histories. One describes the extensive multiple-seam experience at the Harris No. 1 Mine in West Virginia, a second contains examples of "extreme" multiple-seam mining from the central Appalachian coalfields, and a third describes interactions with regard to longwall mine experiences in Pennsylvania, West Virginia, and Utah. The final paper reports on a numerical modeling study that provided some insight into the mechanics of multiple-seam mining. [ ] AMSS Software Package NIOSH has developed a simple, user-friendly computer program called Analysis of Multiple-Seam Stability (AMSS). AMSS can help mine planners to evaluate each potential multiple-seam interaction and take steps to reduce the risk of ground control failure. AMSS begins by evaluating the pillar design. It first calculates the single-seam pillar stability factor (SF)

Jan 11, 2007

By C. H. Brehaut, W. N. Taylor, R. S. Douglas, H. A. Shannon

THE name for this new method of mining is derived from a composition of Horizontal, Radial, Diamond, and the drilling is from raises. This method, worked out at Copper Mountain, B.C., is believed to be distinct in many features from other known methods. GEOLOGY The ore deposits of Copper Mountain are related to the Copper Mountain stock, which is an ideal example of the magmatic differentiation in that it grades from a basic gabbro at the border to an almost pure orthoclase-pegmatite core. The "contact" ore bodies lie along the contact of the gabbro and an older complex of volcanics and sediment termed the "Wolfe Creek" formation. These older rocks, collectively referred to as greenstone, had been fractured prior to the intrusion of the stock and were highly metamorphosed during the intrusion. The "outlying" ore bodies are somewhat different in character, though a similar structural pattern prevails. It is believed that a deep-seated magma of which the Copper Mountain stock is a part has given off solutions that caused a partial granitization of some of the volcanics. Mining problems are caused further by the presence of a series of soft barren dikes intersecting a great many of the ore bodies, which are about 30 ft. wide, strike north-south, and dip at a high angle to the east; and are further increased by the presence of four major faults, with a great many minor faults running at acute angles from them. Fault zones average 8 ft. in width, and consist of gouge and breccia. They strike northeast and dip steeply to the northwest. The faults cut through the ore zones and the dikes, and continue on into the gabbro. The general mine structure with two types of ore bodies, bounded by weak walls and intersected by several series of soft barren dikes and major faults, indicated that a method of mining should be devised that would remove the ore at low cost with the least disturbance of the waste walls and dikes. THEORETICAL ESTIMATE OF STOPING WITH THE DIAMOND DRILL After consideration of various methods, the most suitable one appeared to be horizontal drilling to break the ore in a manner similar to shrinkage stoping. Drilling vertical holes or rings from a bench and breaking to an open slot was eliminated because the weak walls of ore, dike or waste would not permit this type of opening. It was then decided to drill either horizontal radial holes from a raise or parallel holes from a slot cut across the ore body. After discussion, the latter method was believed unsuitable, for the following reasons:

Jan 1, 1945

By J. Shibata, N. Murayama

"Rare earth elements are present in more than 100 minerals, of which monazite, bastnaesite and xenotime are typical. Rare earth elements have excellent chemical and physical properties for industrial use in functional materials such as phosphors, magnets, electronic components, abrasives and catalysts. China produces more than 90 % of the world’s rare earths, and Chinese trends significantly influence the demand and price of rare earths. From the viewpoint of resource securement, it is desirable to separate and recover rare earth elements from low-grade resources and wastes. Phosphate gypsum, which is a by-product of wet phosphoric acid manufacturing, contains low concentrations of rare earth elements. In this research, the separation and recovery of rare earth elements from phosphate gypsum were investigated. A series of recovery methods including washing of phosphate gypsum, leaching of the rare earth elements with sulfuric acid, adsorption and desorption of rare earth elements by using ion-exchange resin, and precipitation of rare earth oxalates were carried out. The separation of rare earth elements from Ca2+ simultaneously leached from phosphate gypsum was also investigated."

Jan 1, 2014

By G. B. Craig, J. Rezek

The critical resolved shear stress of zone-refined zinc single crystals deformed in tension is found to increase with increasing amount of striation substructure. The increase in strength with numbers of striations can be accounted for by a dislocation pile-up mechanism. A somewhat different means of plotting stress-strain data is introduced which allows a more unambiguous choice of yield stress to be made. FEW systematic studies of the role played by mac-romosaic or striation-type substructure in the de- formation of high-purity metal single crystals grown from the melt have been reported. McGrath and Craig' found that striations increased the critical resolved shear stress of zone-refined aluminum crystals, postulating a dislocation blockage by the striations as the strengthening mechanism. Lauri-ente and Pond2 found that, as the etch pit density increased in aluminum crystals grown from the melt, the critical resolved shear stress also increased. Fleischer and Chalmers3 also found changes in the critical resolved shear stress of aluminum crystals grown from the melt at varying rates, but could not be certain whether an increase of strength with rate was due to a higher concentration of impurity in the gage length or to an increase in the number of small-angled boundaries. An early work by Hibbard4 indicated that copper crystals containing lineage boundaries were stronger than those free from this type of imperfection.

Jan 1, 1962