Search Documents

By Harvey S

After considerable experience in connection with the magnetic iron-ores at the South, especially in the Cranberry district of western North Carolina and eastern Tennessee, the writer was led into a thorough investigation of the magnetic separation of iron-ores, and, from this investigation, has gradually been developed a separating machine which it is the purpose of this paper to explain. Numerous United States patents have been issued upon machines for magnetic separation. Since the original patents date back to 1849, it is not possible to-day to establish broad claims upon the principles of electro-magnets as applied in such machines. Among these inventions there are certain types of separators which have very marked practical advantages over the others; and these successful machines, while varying radically from each other in their proportions and arrangements, are all based upon a principle originally explained in a patent which was granted in 1870, and which has now expired by limitation. The problem of practically separating iron-ores, as found in the mines, is very different from the separation of a purely magnetic substance from a purely non-magnetic one, since the crystals of magnetite, scattered through the ore-bearing rock, and sometimes collected in masses, are of very different sizes. The average size of the particles may be definitely ascertained for each mine, and the crushing- and screening-machinery may be adapted thereto, but there will still be a large percentage of very fine crystals which, in the crushing for the average, will not be broken apart from the gangue. If these mixed particles are thrown into the heads they carry gangue with them, and if thrown into the tails they occasion a loss of ironore. There are two methods for preventing such loss. One is, to crush all the material to the size of the finest particles, which means, of course, a large crushing-plant, heavy wear and tear, and excessive cost for repairs, and the production of only a very fine-grained concentrate which our blast-furnace managers, to say the least, do not

Jan 1, 1893

By Guo Xueyi

The nonferrous metal industry is facing the resource depletion, energy crisis and environmental deterioration. The resource recycling is a correct way to promote the nonferrous metal industry development towards sustainable. To realize the resource recycling, the technical support is most important. In this paper, the techniques barrier for nonferrous metal resource recycling are summarized, the fundamental on resource recycling of nonferrous metals are proposed.

Jan 1, 2006

By E. Wolmarans

Dowding, Reynard and Associates Mineral Projects (DRAMP) was approached by the ARM/Lion Ore JV during July 2006 to conduct a feasibility study and control budget estimate for a new greenfield project for their NKOMATI Nickel mine 45 km east of Machadadorp. The scope included the evaluation and review of previous studies as well as a techno-economic trade-off on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous milling. The following document encapsulates the thought process, decisions and the references used in selecting the final comminution route for the new 375 ktpm MMZ concentrator. Apart from the pilot test work performed, design simulations from a number of sources, performance results from a recently commissioned 100 ktpm MMZ concentrator, together with an understanding of the geology and mineralogy of the orebody and possible variations in the characteristics of the orebody over the life of mine were assessed. The results from all the above-mentioned work indicated that it would be possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding (ABC-type) circuit. Autogenous milling is generally considered to be one of the higher risk milling circuits. This is mainly due to the fact that the ore, which is utilized as the grinding media, could be variable in terms of hardness and mineralogy/geology. Nevertheless, it is a very popular route as the cost benefits, more specifically the operating cost, are normally very attractive. This is especially the case when large low grade orebodies are evaluated. In North/South America, autogenous and semi-autogenous grinding circuits have been successfully employed during the past 20 years on large scale low grade operations. Taking all the above factors into account, the DRA/Nkomati project team recommended an autogenous circuit with the option to add steel to both the primary and secondary mills (if required) for the new operation in order to create the opportunity for significant operating cost savings. One has to bear in mind that all the new design simulations and decisions are based on previous work and potential unknown variations within the orebody will never be fully understood until the pit is operational for some time.

Jan 1, 2009

By William P. Blake

The Rainbow Lode is situated at Walkerville, in the Summit Valley mining district, Silver Bow County, Montana Territory, about one mile from Butte City. It was so named ill 1876 by Mr. J. E. Clayton, in recognition of the broadly-sweeping curve of the outcrop across the rounded surface of the eastern slope of a granitic mountain, at an elevation of about 6000 feet above the sea-level. It is on the western side of the range which divides the waters of the Missouri from those of the Columbia. History.—The history of the district is an instructive one. The water-courses and flanks of the hills were worked for years for placer gold. Millions of dollars' worth of low-grade gold have been washed out of the surface gravels below the veins of the district. Missoula Gulch and Silver Bow creek, just below Butte, are noted for their rich placers, and they continue to yield largely, producing within narrow limits from $50,000 to $100,000 dollars' worth of golddust yearly. It is ragged vein-gold, and evidently is near its parent source. It is no doubt derived from the disintegration of the veins of the district, and this conclusion was soon forced upon the miners. The veins which were seen outcropping boldly upon the slopes above them were located, and prospecting commenced. These outcrops were found heavily stained and blackened with oxide of manganese, and were porous and honey-combed in places, showing that the quartz was formerly filled with pyritous ores, and that these ores had decomposed and dissolved away, leaving, however, portions of the precious metal behind, especially at and near the surface of the ground. Assays of the croppings gave variable and often contradictory results; but the fact. that these were the outcrops of lodes bearing gold and silver in depth was patent to any experienced observer of mineral veins. The lodes of the district were first brought prominently to notice by Mr. Clayton in 1876, and in October of that year the Alice mine, upon the central portion of the lode, was opened by Mr. Marcus Daly, now so well known as the superintendent of the Anaconda Copper mine, upon another extremely interesting lode, in the same region.

Jan 1, 1888

By D Gerrard, J Begelhole, J Gerber

The Iron Magnet deposit has been mined since 2007 when Arrium (then OneSteel) commissioned the magnetite concentrator to supply feed to the pelletising plant in Whyalla. The concentrate quality requirement for the customer required consistent product with minimal variability. In the early stages of operation, it was identified that the feed variability introduced significant changes in the concentrate quality, which was outside the acceptable customer limits.In 2011, a geometallurgical regression model was developed that allowed for the estimation of concentrate quality produced from the feed material. This was based on a laboratory-scale Davis Tube Recovery (DTR) test performed on the feed material. The objective of the project was to characterise the raw ore in the pit to allow for blending prior to crushing. By blending the feed to the concentrator, minimal concentrate quality variation within the plant was achieved. The orebody was divided into geometallurgical classes, called ore types, based on the mineral texture and magnetic mass recovery. Each geometallurgical class consisted of material with similar metallurgical performances. For each individual blast pattern, the ore was grouped into the geometallurgical classes and a composite sample was created. The composite sample was put through the laboratory-scale DTR test and the results were used to estimate the metallurgical performance of the material.The characterisation process and feed pile build methodology was applied in early 2013 and went through an optimisation and streamlining phase. Since the implementation of the geometallurgical characterisation process, the plant has seen a significant reduction in concentrate variability and measurable throughput gains. The characterisation process has also increased the amount of material that is now classified as ore.CITATION:Gerber, J, Gerrard, D and Begelhole, J, 2015. Geometallurgy of the South Middleback Ranges magnetite deposit – predicting plant performance from the pit, in Proceedings Iron Ore 2015, pp 555–560 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

EVERY intelligent and practical investigator of minerals says that copper ore is found in various regions of the world and that among others Italy is very rich in it. But very little is mined there, perhaps because of a cowardly Italian avarice which has the power to make us lazy and indolent in carrying out those lofty and fine designs which should reasonably make us proceed swiftly, or perhaps because we are not prone to attempt extraordinary profit but only undertake those enterprises in which we are certain of a return on our investment. The reason for this might also be found in the meager possibility of success, which, since these things are not easily attempted because they are enormous undertakings of doubtful outcome, cools the spirit of men and in place of enthusiasm introduces the fear of loss, the fear of having to sacrifice not only time but also the work and money invested; then they think of the difficulty [II] of discovery, of the impossibility of full ownership, and of the necessity of excavating the mineral marrow from the hardest bones of the mountains with the brawn and efforts of men. To this is added the fear common to many that in attempting such things they may be called fools by certain ignorant and dissolute persons, and it seems better to them to be praised for becoming rich through usury and by many other infamous and illicit methods than to lay themselves open to the danger of censure from such as these. But there are those who deserve still greater censure, particularly princes and all rich and powerful persons, and theirs is an even more useless error than that of those who refrain for the above reasons. If the occasion and means present themselves for both attempting and continuing such a profitable and laudable affair as mining ores and if they hesitate solely because of cowardice or because they give ear to the bayings of ignorant hounds, or if because of their own willfulness they wish to remain prisoners of a detestable and ugly avarice, then this is their own loss.

Jan 1, 1942

By Henry Smith, Stu Brown

"The Williams Mine is Canada's largest gold producer, with annual production of some 500 000 ounces of gold from two million tonnes of ore. Highly mechanized and automated underground mining practices are utilized at the property in order to help achieve high levels of productivity and the most cost-effective mining possible.Planning and design parameters for the underground ore handling system at the Williams Mine are described in this paper. Particular reference is made to the considerations that were built into the system to provide maximum operating flexibility through the use of multiple orepass systems, portable low profile jaw crushers, underground conveyors and automated hoisting equipment.IntroductionThe Williams Mine is situated in the Hernlo area of northwestern Ontario, approximately 40 Ian east of the town of Marathon (Fig. I). It is operated by the Williams Operating Corporation, which is owned equally by Teck Corporation and Corona Corporation, and is one of three adjacent properties forming the HernIo gold camp.The mine commenced operation in October 1985 at a nominal production rate of 3000 tpcd. Through an ongoing capital development program, winch was completed in late 1989, the production rate at the property was increased to its current level of 6000 tpcd. This paper describes the mine planning process and the evolution of current mining strategies with particular reference to the underground ore handling system .HistoryGold mineralization was discovered in 1944 in the Hemlo area of Northern Ontario, near the north shore of Lake Superior. A year later, 11 claims were staked over the showing and subsequently patented by the late Dr. Jack Kerr Williams.Over the next 35 years, other claims were subsequently staked, explored and abandoned in the immediate area of the 11 patented claims . In 1980 a predecessor of the Corona Corporation acquired claims adjoining the Williams property to the east. Drilling on this claim group started early in 1981 and intersected the Hemlo orebody in May of that year. In December 1981, Corona Corporation entered into an option agreement with Teck Corporation to explore and develop the property.A drilling program by LAC Minerals on the II patented claims discovered the Williams orebody in March 1982. The mine started production in 1985, pouring its first official bar of gold on December 6 of that year. Corona Corporation was awarded ownership of the Williams Mine conclusively by a decision of the Supreme Court of Canada on August 11, 1989. The court's ruling ended a legal dispute with LAC Minerals over the property initiated eight years earlier."

Jan 1, 1991

By D Van Doorselaere

The purpose of blasting during mining is to produce a muck pile that can be efficiently loaded and transported. There is an increasing awareness of the variation in muck pile characteristics and its economic implications. It is well known that good fragmentation by itself is not sufficient to optimise the muck loading efficiency. The swelling and configuration of the muck pile also significantly affect the productivity of the loading equipment. The characteristics of a muck pile depend upon the blast design parameters, explosive properties and rock mass geology. This study has focused on the dependence of muck pile configuration on blast design parameters, explosive properties and size distribution of the muck.The field work was done in two phases. In the first phase 12 blasts were monitored, while in the second, three blasts were monitored. The blast design parameters and explosive properties for each blast were documented and the following muck pile characteristics were measured:muck pile height and its distance from the facedistance of throwwidth of the power troughsize distribution by image analysis technique.The effects of burden, bench height, heave energy of explosive, row-to-row delay, powder factor and the mean particle size of the fragments on muck pile configuration were examined. It was observed that muck pile height and distance of throw are strongly influenced by the burden, bench height, heave energy of the explosive and the size distribution of the muck. The width of the power trough depends upon the row-to-row delay, powder factor and total burden. In addition, the effect of the fragment size distribution on the muck pile parameters has also been discussed.CITATION:Singh, S P and Van Doorselaere, D, 2015. The relationship between blasting parameters and muck pile configuration, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 369–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Steven W. Schmauch

A mineral survey by the U.S. Bureau of Mines and U.S. Geological Survey indicate the Blanco Mountain RARE II area has low potential. Lode deposits consist of small, mineralized quartz or quartz-gossan veins. The veins are sparse and widely separated and lead, silver and gold content is restricted in amount and concentration. No gold or other potentially economic minerals were found in a placer deposit. There is no evidence of industrial mineral, geothermal, or energy resource potential in the study area. INTRODUCTION A mineral resource survey of the Blanco Mountain RARE II area (No. 5059), Inyo and Mono Counties, California was conducted in July 1981. This report summarizes the results and interpretations of the Bureau of Mines investigation.

Jan 1, 1982

By Joachim J. Hauser

William F. Hosford, Jr. (Massachusetts Institute of Technology)—Dr. Hauser has used a very interesting method to study the interaction of dislocations on different slip systems, but it should be pointed out that the analysis of the experiments is subject to a serious criticism. He states that "the effect of the compression can be adequately described by one slip system." The effect of frictional constraint during the compression makes this quite unlikely. When a block of metal is compressed its lateral expansion requires a sliding of the metal over the compression platens. The role of friction in the interface between the deforming metal and the platens is to increase the normal force required for the compression. Analyses1213 have shown that, in general, the additional force, p, required for the compression is a function of l/h where is the coefficient of friction, I is the length of the speci- men in contact with the platens. For a constant COefficient of friction, isho' shows that P should increase exponentially with pl/h for both plane strain and axially symmetric compression. For a compression specimen, Fig. 7, whose cross section perpendicular to the compression axis is a rectangle whith one dimension L, much larger than the other W, a much larger force would be required for appreciable flow parallel to L than for flow parallel to U7. Therefore lateral strain in the W direction, EW, should be much greater than the lateral strain in the L direction EL. Since L/H = 14.5 for Dr. Hauser's crystals, and since no lubrication was used, it seems questionable that appreciable lengthening of the crystals could occur. Because the theories of frictional constraint have been derived for isotropic polycrystalline materials, it was decided to make experimental measurements on a single crystal. A section 3.590 in. long was sawed from an aluminum single crystal with a square section of 0.249 in., so that L/W= 14.4. This crystal was tested in compression between dry ground steel platens. Fig. 8 shows the orientation of the crystal and the axis of compression. The face for compression was chosen so that the operation of the single-slip system which would be predicted in the absence of friction would lead to a larger strain in the length direction than in the width direction. The dimensional changes of the width and length as well as the height were measured frequently during the compression with micrometers. Width strains were calculated from the average of readings near each end and at the center. A plot of the length strain, EL, against the width strain E w is given in Fig. 9. The slope indicates that the EL amounted to only 2.5 pct of cw. Other compression tests on similar crystals with shorter lengths also showed severely limited elongation. Even for a crystal with L/W = A.0, EL was only about 26 pct of cw. Because of the frequent interruptions of the tests for dimensional measurements should have decreased the frictional constraint by allowing a reseating of the platens, even smaller elongations under continuous testing seem probable. These tests on long narrow crystals show that essentially plane strain conditions prevailed. We may assume that Dr. Hauser's crystals deformed similarly. That the compression can be described by the

Jan 1, 1962

By Tadeusz Cyrul

Results of a large scale compression test in situ are the subject of discussion. A cube of coal having an edge length of 1.5 meters was subjected to uniaxial compression tests in situ. At the same time both load and deformation were controlled. Deformations were measured on 60 short measurement bases, each 23 cm in length. The bases were uniformly distributed on the side surface of the cube, forming five horizontal rows and twelve columns on the development of the surface. Readings were taken from each gauge for each level of loading which was increased step by step. Due to heterogeneity of the rock, readings showed scatter. Scattered data were approximated by a plane, using the least squares method for each row separately and for the entire population of bases. Orientation of the planes are analyzed. The geometrical measure of the bending moment is introduced. It shows that the magnitude of the bending moment and the bending plane differed from row to row, thus implying that the cube was not only bent but twisted as well. This complex behaviour of the coal cube is apparently caused by its heterogeneity and vertical anisotropy. The results constitute a contribution to the verification of existing design criteria on the stability of mining pillars.

Jan 1, 1984

By J. W. Faust, H. F. John

Generalized conditions for rod or ribbon growth by the twin plane re-entrant edge mechanism are given. It was shown that this mechanism can result in growth of twinned platelets from dilute metal solutions. The platelrts 01 the fee metals are faceted by (111) planes and contain two or more twin planes. Microsegregation traces were revealed in silver grown from a thallium solution. VOGEL has already set down conditions for dendritic growth;1 however, this was the normal single-crystal dendritic growth experienced during solidification. In this work it is desired to set down the crystallographic conditions that will lead to rod or ribbon growth with smooth facets. These are as follows. a) The growth must be crystallographically limited (i.e., faceted growth). b) In order to have directed growth, some mechanism must allow easier nucleation than two-dimensional nucleation. That mechanism is afforded by the re-entrant edges at twin planes.213 Thus there must be twin planes present in the rods or ribbons. c) The growth direction must lie in the twin plane. If not, the twin plane will grow to the face or side of the ribbon and the site of easy nucleation will be lost. d) The growth direction must be parallel to at least one plane of the faceting planes, and no set of the faceting planes can be perpendicular to the growth direction. A corollary to these conditions involves the number of twin planes necessary to maintain the indestructible re-entrant edge. The number depends on the crystal structure of the material. An analysis of the data available shows that a material whose faceting planes form an open figure requires at least one twin plane while materials whose faceting planes form a closed figure require at least two twin planes in order to form the indestructible re-entrant edges for extended growth. The conditions and an assessment of the possibility of rod or ribbon growth are given in Table I for several crystal systems. As can be seen the fee, diamond and zinc blende, or-thorhombic, rhombohedral, and one form of the hexagonal lattice systems can yield this type of growth, but not the bcc metals nor the hexagonal

Jan 1, 1965

By Z. T. Bieniawski

Engineering rock mass classifications have received prominent attention as design aids in rock tunneling. Support selection in civil engineering tunnels and chambers is often based on such classifications. In the field of mining, rock mass classifications have not been utilized to the same extent but some applications have been made. This paper considers the current rock mass classification schemes from the point of view of their potential in mining. Case histories are described featuring their use in assessing the cavability of ore as well as entry stability and support. Current possibilities for rock mass classifications as design aids in mining are outlined.

Jan 1, 1980

By M. W. Strong

The technique of handling drilling muds varies somewhat, partly because of personal factors but mainly because of differences in formation, the type of problems, and the general drilling conditions in different localities. The much greater depths to which bore holes are now carried have made necessary closer attention to and great modifications of all aspects of drilling-mud technique. Increased depth means smaller hole, smaller drill pipe, smaller clearances, higher pumping pressures, higher differential pressures between shows and the mud column, less accurate control of the weight of the mud column, delayed receipt of formation data, and poorer samples. It means longer delays and greater hazards in rectifying mistakes or dealing with accidental occurrences. Equipment on a larger scale is necessary and more pains must be taken with layout. Lastly, the budget costs of raw materials have risen to high figures and economy of time and of direct monetary expenditure have come to mean much more than formerly. A mud laboratory is now part of the essential establishment of a modern oil field and to it current problems can be submitted for the most thorough investigation. The detailed chemical properties of all materials purchased or quarried have to be investigated. Detailed data on the physical properties have to be ascertained and research on improvement of material and its most efficient use has to be carried out. In this paper will be discussed the main mud problems of Iran, some of which are peculiar to local conditions while others are of the general type common to all workers in this subject. Underground Conditions In deep wells in Iran the normal overburden may consist of: (1) up to several thousand feet of marls with interbedded sandstones and limestones of varying porosity and permeability; (2) beneath this a chemical series of rock salt and anhydrites, containing various marls and thin limestones,

Jan 1, 1939

By M. W. Strong

The technique of handling drilling muds varies somewhat, partly because of personal factors but mainly because of differences in formation, the type of problems, and the general drilling conditions in different localities. The much greater depths to which bore holes are now carried have made necessary closer attention to and great modifications of all aspects of drilling-mud technique. Increased depth means smaller hole, smaller drill pipe, smaller clearances, higher pumping pressures, higher differential pressures between shows and the mud column, less accurate control of the weight of the mud column, delayed receipt of formation data, and poorer samples. It means longer delays and greater hazards in rectifying mistakes or dealing with accidental occurrences. Equipment on a larger scale is necessary and more pains must be taken with layout. Lastly, the budget costs of raw materials have risen to high figures and economy of time and of direct monetary expenditure have come to mean much more than formerly. A mud laboratory is now part of the essential establishment of a modern oil field and to it current problems can be submitted for the most thorough investigation. The detailed chemical properties of all materials purchased or quarried have to be investigated. Detailed data on the physical properties have to be ascertained and research on improvement of material and its most efficient use has to be carried out. In this paper will be discussed the main mud problems of Iran, some of which are peculiar to local conditions while others are of the general type common to all workers in this subject. Underground Conditions In deep wells in Iran the normal overburden may consist of: (1) up to several thousand feet of marls with interbedded sandstones and limestones of varying porosity and permeability; (2) beneath this a chemical series of rock salt and anhydrites, containing various marls and thin limestones,

Jan 1, 1939

By P. W. Bakarian

Previous determinationl,2,3 of the texture of magnesium and its alloys have shown only slight variations in the principal features of the structure. This investigation presents pole figures for magnesium and two of its alloys, in which differences of some magnitude will be shown. Schmid and Wassermann have considered the texture of magnesium in analogy with that of zinc—also a hexagonal lattice. Whereas the zinc texture is said to be derived primarily through basal slip and secondarily through {IO2}† twinning, the {102} twinning is considered impossible at the later stages of the rolling in magnesium because of its smaller axial ratio. This state of affairs appears reasonable for pure magnesium, but for alloy textures the situation is more complex. A double orientation similar to that found in zinc has been reported by J. D. Hanawalt,4 and the addition of small amounts of calcium to magnesium and its alloys to produce a double texture was noted by J. C. McDonald.5 The pole figures of this investigation, using an improved X-ray technique, show these various textures. The dependence of directional properties of rolled sheet on modifications of texture is well recognized. Correlation of physical properties with existing texture should be even more significant if quantitative valuations are attached to the various areas on the pole figures. Such a quantitative technique is developed herein. Experimental Method Two alloys were used, besides high-purity magnesium. In each case, the metal was extruded to bars 1/2 in. thick and hot-rolled to a thickness of about 0.075 in. It had been established previously that such a reduction was more than sufficient to eliminate the extruded structure. The rolling proceeded in the same direction as that of the extrusion, without any cross rolling. The temperatures corresponded to normal commercial practice, averaging around 600°F. A unique method of preparing the sample was developed in this work. Instead of using a flat specimen, a stem of the metal was cut out of the rolled sheet in the desired direction (rolling direction) as shown in Fig. I. From a sheet of 0.075 to 0.065-in. gauge, the stem was cut to a square cross section with a jeweler's saw, rounded with a file and polishing paper to a diameter of 0.060 in. and evenly etched in dilute hydrochloric acid to a diameter of 0.038 + 0.001 in. In this way, a cylinder of the original sheet with its axis in the desired direction was produced. By using this type of specimen for the pin-point pictures, any variance in the absorption of the diffracted beam at the various angular settings of the specimen, was completely eliminated.*

Jan 1, 1942

By P. W. Bakarian

Previous determinationl,2,3 of the texture of magnesium and its alloys have shown only slight variations in the principal features of the structure. This investigation presents pole figures for magnesium and two of its alloys, in which differences of some magnitude will be shown. Schmid and Wassermann have considered the texture of magnesium in analogy with that of zinc—also a hexagonal lattice. Whereas the zinc texture is said to be derived primarily through basal slip and secondarily through {IO2}† twinning, the {102} twinning is considered impossible at the later stages of the rolling in magnesium because of its smaller axial ratio. This state of affairs appears reasonable for pure magnesium, but for alloy textures the situation is more complex. A double orientation similar to that found in zinc has been reported by J. D. Hanawalt,4 and the addition of small amounts of calcium to magnesium and its alloys to produce a double texture was noted by J. C. McDonald.5 The pole figures of this investigation, using an improved X-ray technique, show these various textures. The dependence of directional properties of rolled sheet on modifications of texture is well recognized. Correlation of physical properties with existing texture should be even more significant if quantitative valuations are attached to the various areas on the pole figures. Such a quantitative technique is developed herein. Experimental Method Two alloys were used, besides high-purity magnesium. In each case, the metal was extruded to bars 1/2 in. thick and hot-rolled to a thickness of about 0.075 in. It had been established previously that such a reduction was more than sufficient to eliminate the extruded structure. The rolling proceeded in the same direction as that of the extrusion, without any cross rolling. The temperatures corresponded to normal commercial practice, averaging around 600°F. A unique method of preparing the sample was developed in this work. Instead of using a flat specimen, a stem of the metal was cut out of the rolled sheet in the desired direction (rolling direction) as shown in Fig. I. From a sheet of 0.075 to 0.065-in. gauge, the stem was cut to a square cross section with a jeweler's saw, rounded with a file and polishing paper to a diameter of 0.060 in. and evenly etched in dilute hydrochloric acid to a diameter of 0.038 + 0.001 in. In this way, a cylinder of the original sheet with its axis in the desired direction was produced. By using this type of specimen for the pin-point pictures, any variance in the absorption of the diffracted beam at the various angular settings of the specimen, was completely eliminated.*

Jan 1, 1942

By Z. Nivolianitou

This article aims at highlighting the importance of technological innovation, namely the potential use of Virtual Reality (VR) technology, as a Sustainable Development Indicator for the minerals industry. Nowadays, VR is regarded as a mature technology for real world representation, and it has been already applied in various domains such as architecture, topography, aeronautics, medicine, and lately in the process industry. Several industrial sectors already use VR tools, as the car industry for improving car ergonomics and design and the aviation industry for both pilot and maintenance crew training. It is well known that the mining industry, as well as the process industry, requires people to work in hazardous environments and situations, often inadequately trained owing to limitations in time and resources, building thus the potential for minor or major accidents.

Jan 1, 2007

By John C. Smock

The question of the proper valuation of mines of iron ore was suggested to me by the difficulties experienced in getting answers for the United States Census Office, while I was engaged in the work of collecting the statistics of mines in New Jersey and New York. The answers to the questions relating to values of real estate of mine properties varied so greatly that it was necessary to revise them according to some general principles of valuation. Generally the returns of mine proprietors seemed to be too low. There were, however, examples of what would be termed excessive valuation. The subject appeared to be of practical importance, and led to the paper here presented. The following table of selected mine statistics is given, prefacing the discussion of the principles of valuation. It is in part made up of census returns and partly of data obtained directly from mine owners and managers. The mines which were selected for the several groups and mining districts include nearly all of those from which the more full and carefully filled returns were received, and are also representative of their respective districts. Hence the averages obtained from them become good types of these groups or districts. The mines of New Jersey appear in six groups, each containing from three to eleven mines, or, in all, thirty-four mines. The magnetic iron ores of New York are in four well-marked groups, and there are twenty-six mines in them. Then follow the red hematite mines of St. Lawrence and Jefferson counties; and, lastly, the brown hematite groups of Dutchess and Columbia counties, and those of the adjacent parts of Connecticut and Massachusetts. The whole number of mines represented by the table is eighty-eight, of which twenty-eight are hematite mines. The first column gives the value of the real estate; the second that of the plant; the third is the sum of these two, or the capital invested. Then follow the number of men employed, the amount of wages paid during the census year, and the value of materials used in mining and preparing the ores for market." The seventh column gives the total expendi-

Jan 1, 1882

By Peng Bing

Stainless steelmaking dust is classified as a hazardous waste due to higher than acceptable heavy metal leachabilities such as zinc, lead, cadmium and chromium. In addition to being an environmental hazard, the flue dust is also an economical concern to stainless steelmakers as it contains large amounts of valuable alloying elements, especially for iron, chromium and nickel. A new technology of direct recycling of stainless steelmaking dust has been developed to recover the metals from the dust. But it was found that zinc was accumulated in the dust collection system in practical run of direct recycling. This study focuses on the effect of the operating parameters such as temperature, dust feed rate and the ratio of CO to dust on the reduction of zinc oxides present in the dust. The mathematical model for the reduction process was setup based on the experimental research. According to the mathematical model, the temperature has obvious effect on the reduction of zinc. It is benefit to the process of zinc reduction to increase the temperature. But the temperature will not be the main factor for the reduction process after 1228C. It will promote zinc reduction to decrease the dust feed rate and control the ratio of dust to CO. It was also found from the experiments that ZnFe2O4 in the dust could be decomposed at high temperature. Decomposing ZnFe2O4 in the dust increases the recovery of zinc from the dust distinctly.

Jan 1, 2006