Search Documents

By G. K. Burgess

§ 22. THe results published in Professor Howe's paper10 of our determinations on the Ac3 and Ar3 points for a series of commercial carbon steels " containing manganese in varying proportion, represent the average temperatures found by taking several (4 or 5) heating and cooling curves. The accompanying curves, Figs. 6 and 7, are, for each steel, the first heating and cooling curves as obtained by the inverse-rate method of Osmond, using a cylindrical chronograph sensitive to 0.1 sec. for recording time. Simultaneous observations were also taken by the differential method with a platinum neutral and plotted by Rosenhain's derived differential method and gave substantially the same results, the curves having sensibly the same contours in both cases.12 The observations were taken in vacuo on cylinders 5 by 1 in. in length bored to center with a 1/8-in. hole to receive porcelain insulated thermo-couple, and inclosed in an out- and in-glazed Berlin porcelain tube heated electrically by platinum foil wound on the tube. The vacuum was usually better than 0.1 mm. The heating and cooling of the furnace was automatically controlled by a salt-water rheostat with shaped electrodes, giving a uniform rate of heating and cooling.

Jan 1, 1914

By E. A. Sondreal

Requirements of flue gas desulfurization (FGD) for Eastern and Western U.S. coals will not be the same because of differences in coal sulfur content, ash analysis, and beating value. The effects of these differences and of limited availability of water in the West are the subjects of this paper. Eastern and Central bituminous coals are generally high in sulfur and require removal efficiencies in the range of 70 to 90 percent to meet the Federal emission standard of 1.2 lb SO2/MMBtu. Ash in Eastern coals is low in alkali content and is relatively insoluble in scrubber solutions. High sulfur content and market availability make salable product methods more attractive in the fast and Central United States than in the West. Western subbituminous coals and lignites are generally low in sulfur content, however, only a few deposits could reliably meet the Federal emission standard without FGD, Required removal efficiencies generally fall in the range of 0 to 60 percent to meet the 1.2 lb SO2/MMBtu limit. If the standard were raised to 2 lb S02/MMBtu, approximately two-thirds of Western coals could be burned without FGD. Some Western coals contain ash high in alkali, some of which is soluble in scrubber solutions. This complicates scrubber chemistry, but it also provides the meant for displacing some or all of the limestone requirements when only moderate S02 removal is required. Dry areas in the West would benefit from full commercial developement of dry processes of FGD.

Jan 1, 1974

By Robert S. Becker

The results of a laboratory investigation of coal cutting mechanics and noise is presented. These experiments were performed using a linear cutting apparatus that operates over a broad cutting speed range. The influence of several coal cutting parameters on the noise, force, productivity, and specific energy associated with linear cuts is ascertained. Some basic theoretical aspects of coal cutting mechanics and noise generation are discussed, and the results of the laboratory experiments are used to Formulate analytical models of the coal cutting forces and noise. The analytical model For coal cutting noise is then generalized to account for the more important effects of rotary cutting. Based on the generalized model, an estimate of the sound pressure level at an operator's position is made for a typical continuous mining machine. It is concluded that by employing linear rather than rotary cuts, using deeper depths of cut, slower cutting speeds, and more efficient cutting tools, it is possible to reduce the level of coal cutting noise, as well as Provide benefits to other important areas of underground health and safety.

Jan 1, 1980

By J Player, G Sweby, S Webber, E Jones

Seismic systems are a tool for the monitoring and forecasting the rock mass response to excavation. Common issues encountered at mine site audits and reviews are: how to design an effective seismic system, implementation of the design, interpretation of seismic source results and understanding the reliability of the seismic source. These issues are often a function of several items including: • Experience of site personnel in undertaking seismic system design. • Personnel not envisioning multiple phases of system expansion to understand system robustness issues. • System design/expansion occurring in response to damaging seismic activity rather than planned expansion of a system • The mine access development is often localised in comparison to the total orebody being mined hence, planning sensors in longholes in advance of development rather than in short holes close to development will improve the three-dimensional aspect of the network. • Limited site processing of the seismic event data, hence engineers do not see the uncertainty associated with event location, size, source and system layout. Mine site users require a framework to appreciate the challenges and limitations in locating large events. For example, event locations are given as precise measurements (to the nearest centimetre) whereas the volume of deformation resulting in the event often has dimensions of tens of metres or more (as defined by the source radius). A stronger awareness of the uncertainty of rock mass yield within large seismic sources will assist site users in the interpretation of rock mass damage. The encountered design and implementation errors are reviewed and discussed with a practical set of rules presented to provide a robust seismic system that provides consistent results and increases the user’s understanding of uncertainty in source location and size. The authors’ experience across multiple mine sites, seismic systems and damaging seismic events over a 30 year period has been summarised into practical rules for site personnel of all experience levels.

Nov 29, 2022

By Philip Arthur

The ISASMELT process is making a significant contribution to the global metals industry. ISASMELT furnaces are now operating successfully in eight different countries and treating approximately 3 million tonnes of concentrates and secondary materials per year. The process is currently used in both lead and copper smelting. The most recently commissioned plants were in Germany and China, one for treating scrap copper and the other treating low-grade copper concentrates. The Copper ISASMEL T furnace ("CIF") at Mount Isa Mines Limited ("MIM") has continued to set new operational records, with throughput of more than I million tonnes of concentrate per year and very low operating costs. This paper summarises the latest operational data from the Mount Isa Copper ISASMELT plant and outlines the successful approach to industrial R&D taken by MIM in the development of the ISASMEL T process.

Jan 1, 2003

In today’s competitive steelmaking environment, the optimization and continuous supervision of the blast furnace process is of major importance. Modern probes and process measurement systems can assess the specific operation of the blast furnace. They provide a better and detailed process understanding and control. The benefits are even more important when they are combined with process models and expert systems. Everyday operation, productivity and even the lifetime of a blast furnace can be significantly improved by collecting, interpreting and acting upon such process data correctly. Only a comprehensive knowledge of the various process phenomena together with measurement of process variables inside the blast furnace enables the operators to optimize coke and fuel rates, to run the blast furnace smooth, reliable, and safe, and to make best use of the available raw materials. While the improvement of the blast furnace process with respect to productivity remains the main task, also, the timely identification of abnormalities and the assessment of process variations is an objective. This paper describes the blast furnace measurement systems that are available for everyday automatic use and provides an understanding for the possibilities of modern probes. The different applications are daily blast furnace supervision, charging process optimization, and observation of the internal state. Finally, the paper gives recommendations on probe configurations for different blast furnaces sizes, considering both a technical and an economical point of view.

Aug 2, 2018

By Yi Luo, FENGLIANG WU

Explosions and fires originated from longwall gob due to the formation of methane-air mixture have been a severe threat to coal miner’s lives.Many numerical studies on coalmine fire and explosion hazards have focused on the airflow in roadways and mine gobs. However, most of these studies isolate the gob from its surrounding roadways, and the network analysis and the CFD method are applied independently tomodel the two classes of airflows. This approach greatly limits the ability of simulatingmine ventilation flow, especially unable to consider the effects of gob boundary conditions on air exchange between the gob and the surrounding airways. An innovative finite tube method (FTM) is developed to couple the one-dimensional mine ventilation network (MVN) and the 2D/3D gob flow field (GFF). In FTM, GFF is discretized into a finite number of flow tubes each of which is formed by any two adjacent stream lines. These tubes, representing the gob’s field flow, connect the MVN into a new coupling network. To solve the coupling model betweenMVN and GFF, an iterative solution technique is developed inwhich the MVN analysis is used to evaluate the boundary pressures for GFF simulation and in turn the FTM feeds the GFF results back to the coupling network. Based on the FTM approach, a model for gas migration in gob has been established for delineating the hazard zones of explosive methane concentration and spontaneous combustion. A computer program is developed to implement the FTM simulation. An illustrative example with five flow tubes representing the GFF is created to verify the stability and convergence of the FTM solution process. A simulation example also indicates that the accuracy of FTM is improved by 12% compared with previous method. Results of an application case show that the program is capable of quantitatively evaluating the gob’s risk zones prone for spontaneous combustion and gas explosion as well as performing risk analysis for various ventilation scenarios.

Jul 10, 2020

By Michael D. Loy

This paper examines the computerization steps of United Coal Company of Bristol, Virginia. OVERVIEW Producing close to 7,000,000 tons per year, United Coal Company is one of the most interesting mining companies in the east. Their approach to mining reflects a dedication to modern technologies and extraction methodologies. With varying amounts of production coming from four divisions (a fair amount of production comes from contract operators) and over a billion tons in recoverable reserves, United rests heavily on the planning and engineering efforts of a centralized engineering group. Although each division relies on its own engineering personnel for day-to-day management and operations, long range planning and reserve management is conducted at the corporate engineering level. This group, while extremely competent and efficient, is relatively small (7 people), when compared to the needs of a large mining company.

Jan 1, 1985

By R. Bainbridge

THE Consolidated Mining and Smelting CO. of Canada Ltd. has operated a lead smelter at Trail, B. C., for many years. In order to take advantage of metallurgical advances, as well as to improve materials handling methods, this company, commonly known as "Cominco," commenced planning a program of smelter revision and modernization some years ago. The first stage of this program involved the design and construction of a new blast furnace gas cleaning system. The selection of equipment, the design of facilities, and preliminary operating details of this system will be dealt with in this paper. The essential problem was to clean and collect 100 tons of dust daily from 153,000 cfm* (12,225 lb per min) of lead blast furnace gas which varied in temperature from 350º to 1100°F. Because it was desired to collect the dust dry, either a Cottrell or a baghouse cleaning plant was to be selected. Comin-co's many years of experience with both systems provided a background for choosing the most satisfactory installation. All information pertinent to the two methods of dust recovery was carefully investigated, and it was decided to replace the existing equipment with a baghouse. Very briefly, the reasons for this decision were as follows: 1—A baghouse installation would be practical because the SO2 content of the gas was low and corrosion would not be a problem if the baghouse operating temperatures were held sufficiently above the dew point. 2—Variations in the physical characteristics of fume and dust, which are inherent in this blast furnace operation, should not substantially affect the operating efficiency of a baghouse. 3—For the same capital cost, metal losses (stack and water losses) would be appreciably less in a baghouse. 4—A baghouse would be easier to operate, and would not require the use of highly skilled labor. 5—Operating and maintenance costs of a bag-house would be lower. 6—The only available space for reconstruction was relatively small, and not suited to a Cottrell installation. Once the baghouse system was decided upon, detailed design of the installation was begun. Baghouse Design Gas Cooling: Before the required capacity of the baghouse could be determined, the method of cooling the gas to the temperature necessary for bag-house operation had to be chosen. The problem confronting the design engineers was how best to cool 153,000 cfm of gas from a temperature ranging from 350°F to brief peaks of 1100°F, down to 210°F, the maximum safe baghouse inlet temperature. A survey of existing blast furnace gas temperatures in the outlet flue showed that the normal range was as given in Table I. The obvious choices of cooling method were: 1— cool completely by the addition of tempering air; 2—utilize a heat exchanger; 3—cool by radiation; and 4—cool with water spray in conjunction with the admission of tempering air. The advantages and disadvantages of the various cooling methods were: Air Addition: To cool completely by the admission of tempering air involved tremendous volumes, Fig. 1. For example, to cool 1 lb of blast furnace gas at 450°F requires 1.84 lb of air at 80°F or 1.60 lb at 60°F. As it is necessary to design for peak conditions, it can readily be seen that volumes of tempering air in the order of 1,500,000 cfm would have to be handled. Using the normal design figure of 2.5 cu ft per sq ft of bag area, a baghouse installation comprising some 600,000 sq ft of filter cloth would be necessary. Such design requirements would be prohibitive, not only from a standpoint of capital expenditure, but also because of space limitations. Heat Exchanger: The utilization of a heat exchanger was given serious consideration. A horizontal tube unit using air as the medium to cool the required volume of blast furnace gas from 400" to 250°F was investigated. Cooling above 400°F would be done by water spray, and below 250°F by admission of tempering air. The estimated capital cost of such a unit was found to be prohibitive. From an operating standpoint, there was considerable doubt as to whether the soot blowing equipment provided would effectively keep the dust from building up on the tube surface. The performance of heat exchangers operating on dusty gas in other company operations had not been too favorable. Radiation Cooling: Although somewhat cumbersome, gas cooling by radiation from 'trombone' tubes or other similar equipment (cyclones) is employed in many metallurgical operations. Such an installation was also considered. However, calculations showed that an installation much larger than the space available would be required to handle the gas volume involved. For example, to cool 153,000 cfm of blast furnace gas from, say, 600' to 250°F (i.e., remove in the order of 58,500,000 Btu per hr with heat transfer rates varying from 1.1 Btu per sq ft per hr per OF for the higher temperature ranges to 0.88 Btu per sq ft per hr per OF for the lower ranges) would need a cooling area of some 175,000 sq ft.

Jan 1, 1953

By G. Gerbeth, Y. Gelfgat, A. Cramer, A. Bojarevics

The production of highly porous metallic substrates requires an effective and well controlled production of metallic fibres with diameters in the range of 50 to 200 microns. The melt extraction, where a quickly rotating wheel extracts fibres directly out of the inductively heated melt, is a promising technology for that purpose. The main limitations of this process are due to turbulence within the melt and a wavy motion on the surface. Both effects give rise to strong and time dependent deformation of the melt surface which, in turn, causes non-stationary conditions of the contact zone between the extraction wheel and the melt. In the patent literature many examples can be found which try to overcome these problems by submersing mechanical parts directly into, or placing them at least in close vicinity to the melt, aiming at a stabilisation of that contact region. Even made of heat resistant ceramics they suffer from corrosion or cracks and do not work reliable at all. The present work describes a non invasive control mechanism by means of a magnetic field. Model experiments were carried out to study the calm down of the turbulent surface of a inductively stirred melt. The stabilisation of the melt surface has been demonstrated in practise by the installation of a solenoid at a working extraction facility under rough industrial conditions like a powerful induction heating and vacuum.

Jan 1, 1999

By A. T. Yu

Technology and economies of scale have, in the past decade, brought about the emergence of giant vessels. Meanwhile, to answer the need for rapid dispatch, as a means of combating the proportionately far greater demurrage charges, shiploading and unloading speeds have soared (Ref. 1, 2, 3). As the loading and unloading rates have dramatically increased, so has the cloud of dust grown in unbearable proportions. It not only has threatened to be a real menace to machinery and men, but in certain instances has also seriously jeopardized fish and marine life (Ref. 4). In an era when ecology is king, dust in shiploading and unloading can no longer be shrugged off as a mere public nuisance, and its control is now duly recognized as of grave concern to all. Even if public outcry were not a problem, from the operator's own parochial point of view, dust can adversely affect productivity and the well-being of the operating personnel. Without adequate control, it can also result in costly equipment maintenance, particularly when the dust is micronic in size, and abrasive. The Hierarchy of Control Techniques Given the great fortune of not yet having to deal with gas and odors, in the jargon of pollution control, our problem is confined to having to control "particulates" only. To deal with "particulates", the myriad of dust control techniques can be utterly confusing to those who are not entirely well versed in the methodology. Our analysis of what is available to date results in the following hierarchy of logical preferences: 1. Prevention 2. Removal 3. Suppression 4. Containment 5. Dilution Since it deals with the root cause, prevention always outranks the cure. Once the dust is generated, removal nips it in the bud. Only when dust removal is

Jan 1, 1972

By K. K. Kelley

Synthetic fluorphlogopite mica (KMg3AlSi3010F2) is a relatively new product developed at the Norris (Tenn.) Station of the Bureau of Mines, Thermodynamic data have applications both in the production and use of this product, and the work described in this paper was undertaken to fill the need for such data. Measurements were made of the heat of formation at 298° K., the heat capacity between 50° and 298° K., the entropy at 298° K., and the heat-content and entropy increments between 298° K. and a maximum of 1,804° K. These basic data are combined to obtain heats and free energies of formation of the mica from the elements and from molecular constituents at temperatures ranging from 298° to 1,800° K. Minimum heat requirements to form melted mica from commonly used ingredients were calculated.

Jan 1, 1959

By John Durkin

This report discusses the configuration and system deployment for the postdisaster surface seismic system for detecting and locating trapped miners. It analyzes the results of 15 field tests to define a signal model, background noise levels, and subarray performance. A waveform modeling procedure is described and compared with observed waveforms. The resulting similarity indicates that the major factors affecting the signal amplitude, waveform, and spectral character are understood. A model is presented which gives the sig-nal amplitude as a function of source type, source depth, and horizontal off-set between source and receiver. Using this model a curve is presented which gives the range at which a signal will be detected for different signal and noise levels. Finally, and most important relative to the mission of the system, the ability of the system to detect signals on one or more subarrays is put into a probabilistic framework. For a strong source it is almost certain that a subarray directly over the source will detect the signal. After signal processing, it is highly likely that signals will be detected on sufficient subarrays to locate the trapped miner. Location errors have been found to be less than 100 ft in the majority of cases. Techniques have been used that can reduce the location errors to this level even when soil layer variation between subarrays is severe.

Jan 1, 1981

By Josef Maierl

For the production of advanced high strength steel grades (AHSS) like API X80/X100, dual-phase, martensitic and complex-phase grades a number of hot strip mills need to extend their limits in terms of power and flexibility. Especially for cooling and coiling of these new materials, Primetals Technologies developed the “Power Cooling” and “Power Coiling” technologies. Power Cooling combines the advantages of conventional laminar cooling or “low pressure cooling” with the newly developed “high pressure cooling” with highest cooling rates for flexible operation. The Power Coiler which is needed to coil those high strength grades especially at thicker gauges ensures reliable strip-coiling for a most economical production. To enhance the reliable production of high-strength steel grades for a wide range of strip dimensions, the automation system with its advanced models is an integral part to the mechanical design. In this context the paper presents examples for the installation of power cooling and power coiling in new and modernized HSM.

Aug 16, 2017

The Iron Ore Company of Canada (IOC) is the largest manufacturer of iron ore pellets in Canada and its customer base covers North American, European and Asian steel producers. The company operates a mine, concentrator and a pelletizing plant in Labrador City, Newfoundland and Labrador, as well as port facilities located in Sept-Iles, Quebec. It also operates a 418-km (260-mile) railroad that links the mine to the port. IOC has approximately 1,900 employees. Its shareholders are Mitsubishi Corp. (26.18 percent), Labrador Iron Ore Royalty Income Fund (15.1 percent) and the international mining group Rio Tinto, which is its major shareholder (58.72 percent) and operator, with activities in more than 40 countries throughout the world. The IOC was incorporated in 1949 and by 1954 it had completed the Quebec North Shore and Labrador (QNS&L) rail line. IOC began mining in Schefferville, Quebec by 1954 and closed those operations down in 1982. In 1962, IOC commissioned the present day Carol Project consisting of mining, concentration and pelletizing facilities in Labrador City, Newfoundland. In 2004, IOC shipped its one-billionth tonne of ore on the QNS&L Railway. In 2005, IOC celebrated 50 years of mining history. The company expressed an interest in reducing the amount of oversize material (>1 m x 1 m x 1 m or 3.2 ft x 3.2 ft x 3.2 ft) being produced and its subsequent downstream effects, including in-pit sorting and reduction, damage to mobile equipment and significant delays in the loading pockets and the primary crushers. To achieve this goal, an oversize reduction project was undertaken by the mine that, to date, has significantly improved upon baseline measures. One key approach used to reduce the amount of oversize was the implementation of thicker emulsion. The introduction of a thicker emulsion provided more resistance to the forces created by dynamic water and reduced the infiltration of the emulsion into the cracks and fissures of the rockmass, resulting in reduced amounts of oversize and more consistent fragmentation throughout the muckpiles. Additionally, a significant reduction in nitrates leached into the mine water discharge has been realized. To determine the effectiveness of the oversize reduction project, IOC used a first-of-kind technology to assess fragmentation presented to the shovel at the digging face. A digital vision system (DVS) was installed on one of the shovels to capture images that were stamped with GPS locations. A large population of digital images were analyzed to produce a robust fragmentation distribution baseline that was used as one of the mine key performance indicators (KPI). Changes to blasting practice were subsequently measured against the baseline KPI to assess effectiveness.

Jan 1, 2011

By C. H. Burgess

ON June 5, 1947, Secretary of State George C. Marshall in a speech at Harvard University outlined a plan for the economic recovery of Europe. The plan contemplated that the United States should provide assistance which would enable the European nations better to help themselves and to help each other to reconstitute from their war-torn lands conditions which would make possible decent standards of living.

Jan 1, 1950

By Romel B. Villanueva

At the Yanacocha gold mine, in the Andes of northern Perú, the first instrumental tests were carried out in October 2019 to detect the initiation sequence of a production blast by detecting the EMF signal produced by the detonation from each blast hole in the sequence. Several experimental tests were carried out to choose the correct antenna and find the best setup of the high-speed Data Acquisition device (DAD) to detect these electromagnetic waves. Finally, the first measurement was obtained. With the instrument recording at a rate of 1 million samples per second, the initiation sequence was detected with 99.5% accuracy. It was found that it corresponded, without a doubt, to the designed scheme. The main result is that these tests provide us with a method and instrumentation to verify if the planned initiation sequence is carried out correctly in the field. In this way we can find operational deviations and detect possible misfires. This method has proven to be accurate, fast and easy to implement, mainly requiring an EMF signal capture equipment that can record at very high speed, something that is increasingly easier to satisfy with the development of microcontrollers. On the other hand, the type of antennas used in this method are low cost and very commercial. These tests have improved our understanding of the nature of detonation and have marked a new milestone in the development of blasting instrumentation in Peru.

Jan 21, 2025

By D. Pillay

Outsourcing? and ?sub-contracting? have become buzzwords in recent years, as SA industry becomes increasingly exposed to the global economy, and global competitiveness. In its effort to ?catch up? after years of relative isolation, there is a concerted effort to learn from global ?best practice?, in order for South African companies, and the SA economy, to become ?winners?. There seems nothing wrong with this approach at face value. Companies need to compete and be profitable if they are to remain in business. Failure will in the end mean bankruptcy, and the loss of jobs. However, if one interrogates the precise practices, and their implications for all concerned?not just shareholders and employers, but workers, communities, the environment, future generations, the national economy?then the picture can change dramatically. ?Best practice? for whom?

Jan 1, 1999

During the second quarter of 1983, the economic recovery showed further strength abetted by the performances of consumer spending, residential investment, and the slowing down of inventory reductions. Real gross national product (GNP) increased from the first to second quarter at an annual rate of 9.2 percent, compared with 2.6 percent from the fourth quarter of 1982 to the first quarter of 1983 and an overall 1.9- percent decrease in 1982. Total industrial production increased 1.8 percent in July, and productivity as measured by output per man-hour increased 1.3 percent between 1982 and the first quarter of 1983 (table 1). Especially noteworthy .was the performance of real consumer durable goods expenditures, which increased at an annual rate of 32.0 percent from the first to the second quarter (about half of the increase consisted of automobile sales) and real consumer spending, which increased between these periods at an annual rate of 9.7 percent. Residential investment increased at an annual rate of 76.1 percent between the first and the second quarters,1/ and private housing starts by about 38,000 units in both March and May.

Jan 1, 1983

By D. Spitty

Mining companies often have many disparate systems and repositories of data in their organization for planning and scheduling outbound mining supply chains. To optimize ore quality, throughput, transport logistics scheduling and delivery to contract, planning teams need to model and manage the value chain accurately and achieve a consolidated, enterprise view of operational performance. Planning teams coordinate a complex series of activities to ensure production forecast accuracy. They also negotiate and execute complex contracts often with disconnected and limited visibility of production forecasts, quality, and variability with little ability to accurately market potential product specifications over longer time horizons. This market is becoming increasingly dynamic, with increasing variability and the time for planning teams to react is decreasing. This is driving the need towards using science to generate the necessary scenarios required to support the decisions made by planners on a frequent basis. Resource-to-Market is a highly flexible, user-configurable supply chain management system for the mining and metal processing industries. This provides an integrated view of the supply chain that supports the dynamic nature of planning in a mining company, embraces variability of elements across the supply chain with the ability to optimize across all the functional areas of the operation to enable optimal decision making for often competing objectives such as throughput, quality, cost, revenue and profit.

Feb 23, 2014