Search Documents

By Ken-ichi Hirano, B. L. Averbach, Morris Cohen, N. Ujiiye

The influence of plastic deformation in compression on the self-diffisivity of a iron has been measured in the temperature range of 742º to 885°C. The diffusivity is enhanced in proportion to the strain rate, but this dependence decreases with increasing temperature. The magnitude of the strain is relatively unimportant in this connection. Strain rates from 0 to -2 x 10-3 sec-1 were investigated, with a corresponding increase in diffusivity up to 3 x 103 times. The results are analyzed in terms of vacancy diffusion and the excess vacancies introduced during dejornzntion. It is concluded that grain boundaries are the main vacancy sinks in polycrystalline iron and that the vacancy lifetime is therefore dependent on the grain size. A typical vacancy lifetime at 800°C with a nzean grain-boundary intercept of 0.3 cm is of the order of 1 sec. LATTICE imperfections are considered to be the dominant mechanism of diffusion in close-packed crystals. Vacant lattice sites are usually the most important defect, but the enhancement of diffusion along grain boundaries and other short-circuiting paths has been well documented. Inasmuch as plastic straining produces a variety of defects, it would be expected that the application of stresses sufficient to cause plastic flow during a diffusion run might result in an increase in the self-diffusivity. Enhanced self-diffusion in a iron under compressive creep has been observed by Buffington and Cohen' and subsequent coworkers.2 Lee and Maddin3,4 have also found an enhancement in the self-diffusivity of silver single crystals undergoing torsional deformation. On the other hand, Darby, Tomizuka, and Balluffi5 have not observed any significant diffusion increase in single crystals of silver deformed either in tension or in compression, although the results in this case may have been affected by the occurrence of recrystallization. With poly crystalline silver, however, Forestieri and Girifalco6 have found en- hanced diffusion during compressive creep. A small decrease in the self-diffusivity of zinc single crystals under compressive loading has been reported,7 but the applied stresses in these experiments were too low to cause appreciable plastic deformation. For the cases in which enhanced diffusion has been found, a number of common effects have been noted. Usually, the ratio of the diffusivity during straining, Ds, to the diffusivity in the unstrained condition, D,, varies linearly with the strain rate, and does not seem to be a function of the plastic strain, at least up to ? = 0.2. Values of Ds/Du of the order of 100 have been reported'-4 but the enhancement decreases with increasing diffusion temperature. The activation energy for diffusion decreases markedly with increasing strain rate and approaches a level of roughly one-half the unstrained value. Most of the current explanations of these observations assume that excess vacancies are generated by the deformation, but rather large concentrations of excess vacancies and/or long lifetimes are required by these theories.',',',' Since the original work on iron, there has been an important improvement in the compressive-loading technique.2 The early data were also analyzed without taking into account the motion of the coordinate system in the specimens undergoing plastic deformation. This problem has now been solved by a number of investigators (see Refs. 11, 12, and the appendix of the present paper). Consequently, the strain-diffusion runs on iron for the Ds measurements were repeated and extended over wider ranges of temperature and strain rate. In addition, the original diffusivity data9 on the unstrained iron have been corrected for the divergence of the beam in the counting system and new data points have been added, resulting in somewhat different values for the self-diffusi-vities in a iron.10 The new values for Du are used in this paper. A comparison of Ds and Du confirms the large enhancement in the self-diffusivity of iron during compressive creep, as previously reported.',2

Jan 1, 1963

By J. A. Herbst, K. Rajamani, Y. C. Lo

In spite of potential theoretical and economic advantages of large-diameter ball mills, many manufacturers elect not to build them owing to what is perceived as an excessively large design risk. This is because traditional predictions for mill scaleup to large diameters are not always accurate. Alternative methods of analysis and scale-up are required. Recent studies have shown that detailed population balance models which account for important grinding subprocesses (grinding kinetics, material transport, and classification) are capable of predicting the performance of small- and intermediate-diameter mills (up to 4.3 m, or 14 ft) from small-scale batch tests. These same models are used in the current study to predict the performance of a "borderline "large ball mill (4.7 x 5.5 m, or 15 x 18 ft) at Asarco's Sacaton operation, a ball mill (5 x 5.8 m, or 16.4 x 19 ft) at Kennecott's Chino operation, and one of the world's largest ball mills (5.5 x 6.4 m, or 18 x 21 ft) at Cities Service Pinto Valley operation. Model parameters required for scale-up have been estimated in a 380-mm-diam (15-in.-diam) batch mill. Predictions are compared with the results of detailed plant sampling in the three plants. For the Sacaton and Chino operations, the error of the predictions was found to be less than 2.5%, while the corresponding error for the Pinto Valley operation was less than 2.7%. It is concluded that proper representation of the major subprocesses of grinding in the model equations is the key to achieving accurate scale-up. Of special importance is the need to account for the size distribution of the grinding media and the influence of the size distribution environment in the mill on grinding kinetics.

Jan 1, 1986

By William C. Pearson

In past years, the usual justification for underground mining of limestone has been the depth of the overburden, perhaps 100 feet thick or more. At our Okolona Quarry in suburban Louisville, Kentucky, the overburden is usually shallow -- it averages 8 to 10 feet in thickness. However, in July 1980, we began development of an underground limestone mine on that property which also includes surface mining operations.

Jan 1, 1983

By Francis S. Kendorski

Over the past 25 years, the present author has written with several co-authors a series of papers beginning with the landmark paper in the 1st International Conference on Ground Control in Mining in 1981, in turn, based upon U. S. Bureau of Mines (USBM) funded contract research managed by the author with a final report issued in 1979, all concerning this paper?s title subject, Effect of Full-Extraction Underground Mining on Ground and Surface Waters. Initially the work was a summary of British, Russian, and Hungarian experience tailored to United States strata conditions, but has evolved into a consistent and well-documented model of the behavior of strata influenced by full-extraction underground mining such as longwall coal mining. The several strata zones recognized in these works, Surface Fracture Zone, Constrained or Aquiclude Zone, Dilated Zone, Fractured Zone, and Caved Zone, have been observed by several workers in the field. The concepts presented initially 25 years ago have been adopted, rightly or wrongly, by state regulators, ground and surface water researchers, and mining practitioners. The development and utility of these concepts and recent findings will be summarized.

Jan 1, 2006

By A. Wright, R. L. Kastelic, W. C. Feyerabend

Gold Fields Mining Corp. is evaluating gold mineralization beneath thick, wet alluvium at the Chimney Creek project, Humboldt County, Nevada. Contamination of reverse-circulation samples has been visually apparent since drilling began in the area. Tests have shown that, while contamination can affect assays, reverse-circulation holes appear to define mineralized zones almost as well as diamond-drill holes. To improve reverse-circulation sample integrity, several techniques were tried (including a stiff-mud injection system) but with limited success. Diamond-core drilling continues to be used in conjunction with reverse-circulation drilling to further delineate the mineralization.

Jan 1, 1993

By Henry M. Howe

In discussing the classification of iron to-day, we are to leave out of consideration the general division into non-malleable or cast iron and malleable iron, as to the adequacy of which no question has been raised; and to confine ourselves to the subdivisions of malleable iron. This has been classified, according to the extent to which the properties imparted by carbon are present (viz., resilience, hardness,strength, and, above all, the capacity for being hardened by sudden cooling from a high temperature), into (1) wrought iron which cannot be hardened, and (2) steel which can be hardened; and this classification I shall, for briefness, term the carbon classification. Until within a few years all authorities, both metallurgical and general, have concurred in explicitly recognizing the carbon-given qualities, and preeminently the capacity for being hardened, as the essential qualities of steel; this is laid down with clearness by every writer on the subject. For several years this old classification has not been sufficient to meet all our needs, since the genius of Bessemer, Siemens, and, I may add, Holley, has produced wrought iron which has been perfectly melted, and thus freed from certain mechanical adhering impurities. This causes what we call homogeneousness for want of a better word, and gives rise to many important qualities which the old wrought iron had not; qualities universally recognized, though not readily described. I shall, for briefness, style them the fusion qualities, and a classification based on them, a fusion classification. These qualities render the new product so vastly superior, for most purposes, to the wrought iron formerly known, that it is neces-

By J. W. Horne

The quantitative determination of salt in petroleum ins generally divided into two steps - (1) extraction of salt from the oil and (2) accurate measurement of the extracted salt. This paper presents a method used by the Bureau of Mines for quantitatively extracting the water-soluble chloride salts4/ from petroleum and discusses important details attendant on the success of the method. Among these details are homogeneity in the dispersion of salt crystals, emulsified brine and other impurities in the oil sample, complete solution of the salt, and total extraction and titration of all the aqueous phase. Recently, the chlorides of sodium, calcium, and. magnesium produced with and present in various oils have developed growing problems of salt deposition and corrosion in the petroleum industry. Therefore, a technical study of various emulsions and salts that accompany petroleum is being made by the Bureau of Mines in cooperation with the State of Oklahoma. One report (5)5 reviewing the literature pertinent to the study has been published.

Jan 1, 1940

By Keith Contor

The concept of using simulators to train operators of vehicles is not new. However, the Bureau of Mines initiated these programs to determine if computer controlled training devices would enhance production and improve safety in the coal mining industry. Two prototype devices have been constructed, tested and are currently operational. The continuous miner and dragline operator training systems both incorporate full scale operator stations using operational controls and displays. The operator interacts with the visual system through the cab controls to perform basic tasks and develop skills required for startup, operation and shutdown of the mining equipment. Data pertaining to the concepts and techniques applied during the design, development and evaluation of the training devices are presented. Descriptions of trainer designs and visual systems for training equipment are presented and the results of the system evaluation are summarized.

Jan 1, 1983

By Hanry Guillén

En la Compañía Minera KOLPA, se analizó el comportamiento de sus operaciones unitarias por el período Marzo - Agosto 2016, en el cual se identificaron procesos asociados a los ciclos de perforación y voladura, bajo los términos de variabilidad NO ESTABLES NI SOSTENIBLES, los mismos que ameritaban medirlos, analizarlos, mejorarlos y controlarlos a fin de adoptar decisiones que conduzcan a operar la mina en términos de calidad y excelencia.

Sep 1, 2017

By Tian Li

Molecular crystal growth during gibbsite precipitation from caustic aluminate solutions under different flow regimes was investigated in three different laboratory precipitators. The gibbsite precipitation experiments were conducted at the same temperature, initial liquor composition and seed type. The Taylor-Couette precipitator and the stirred tank precipitator were operated, respectively, under the laminar and turbulent flow regimes, while the bottle roller precipitator was operated in a complex flow regime, where fluid flows are generated by the end-over-end rotation of the bottles. Comparison of the growth rate estimates from the different flow regimes showed good agreement, which suggests that the hydrodynamic regime has little or no effect on gibbsite crystal growth under the operating conditions employed in this work. The growth rate estimates from the current precipitation study showed a second order dependency on supersaturation and is consistent with a screw dislocation growth mechanism. The findings of the current work are in agreement with previous gibbsite crystal growth studies published in the literature.

Jan 1, 2003

By Slavko Ostojic, V. G. Hill

This paper reviews various bauxite classification schemes with respect to the differences in texture, composition and geological associations of the deposits. It demonstrates that a techno-economic classification, based on: a) associated rock type - lateritic versus karstic, b) content of aluminum ore minerals - gibbsite, boehmite and diaspore, and c) gangue minerals (iron oxides etc.) has a geological basis with natural cut-off points for the bauxite types identified. Thus, this scheme is seen as applicable to bauxite resources. It also provides a basis for their rational exploitation taking into consideration the long-term interests of both the bauxite producing and consuming countries. Against this background, the industrial mineral or non-metallurgical grades of bauxite are seen as localised and relatively rare occurrences. Their consumption should, therefore, be aimed toward the specific (hence more remunerative) products as indicated by the bauxite characteristics.

Jan 1, 1984

By Grigori I. Voiloshnikov

"The long-term studies on development of the technology for precious metals recovery using activated carbons executed by Irkutsk Research Institute of Precious and Rare Metals and Diamonds (IRGIREDMET) were finished by successful introduction of ""Carbon-In-Pulp"" process in Russia (1984).The review of some studies, accompanied by development, testing, introduction and subsequent improvement of considered technology, carried out by IRGIREDMET is submitted in this paper.The basic regularities of gold and silver adsorption onto activated carbons from cyanide, thiourea, chloride and other solutions are investigated using various phisical-and-chemical methods ( X-ray photoelectron spectroscopy, Voltammetry, X-ray microanalysis etc.). Using voltammetry it was found that gold cyanide is adsorbed onto activated carbon without chemical changes and partial reduction of gold is possible only during drying of carbon samples before analysis. Metallic gold and silver may be dissolved in boiling cyanide solution at argon atmosphere when they are in contact with activated carbon surface. Gold adsorption mechanism for activated carbons has great differences from that for the ion exchange resins. So the most probable mechanism for gold adsorption from cyanide solution is adsorption of neutral molecules Me n+[Au(CN)2-]n.X-ray quantitative microanalysis technique was developed to investigate gold adsorption kinetics onto spherical activated carbon. Gold profiles in granules of activated carbon for various adsorption conditions were tested (carbon particle size, mixing efficiency, adsorption time etc.). Mathematical methods were used to determine gold diffusion coefficient within activated carbon granule.The properties of various types domestic and foreign activated carbons were tested and the demands to activated carbons suitable for gold extraction were determined. As a result foreign and Russian activated carbons AG-90, AG-95 were recommended for use at Russian gold plants. Domestic adsorbents are cheaper in comparison with foreign activated carbons. The methods to restore carbon adsorption activity including acid treatment and thermal reactivation were tested and implemented."

Jan 1, 2003

By M. F. Burr, F. V. Lenel, G. S. Ansell

The mechanism of materials transport was studied in a model experiment in which a silver sphere was sintered to a silver plate under an applied external stress near 800° C. For this purpose the rate of growth of the neck between the sphere and the plate which is proportional to the strain rate of the creep process involved in a neck growth was determined by measuring the change in electrical resistance of the away. This rate of neck growth will depend upon the magnitude of the applied external stress. By measuring the rate just before and just after a change in the external load and therefore the applied stress, the relationship between strain rate and stress can be derived. For material transport by slip in a pure metal it is expected that the strain rate should be proportional to the 4.5th power of the stress, while for transport by diffusional flow the strain rate should be proportional to the first power of the stress. It was found that for stresses above 5 X 10' dynes per sq cm (70 psi) the exponent in the stvain rate-stress relationship was near 4.5 while for a stress of 0.7 x 108 dynes per sq cm (10 psi) an exponent of 1.8 was determined indicating that under the conditions of the experiment the transport mechanism for creep in silver shifts from diffusional flow to slip in the region of 0.7 x 106 dynes per sq cm (10 psi). The importance of these findings for an understanding of the mechanism of material transport in conventional sintering (without an external load) is pointed out. In a paper by Early et al.,' the mechanism of material transport during sintering was treated as a creep process. It was pointed out that two possible types of creep processes could operate during sintering. In one of these material transport takes place by vacancy diffusion due to a gradient in chemical potential. The vacancy sinks in this diffusion process may be either grain boundaries, as in Herring-Nabarro microcreep, or regions beneath a surface of small radius of curvature. The diffusive transport may be by volume, grain boundary, or surface diffusion. In the other mechanism, creep takes place by slip, i.e., dislocation motion with its rate generally controlled by dislocation climb. One method of distinguishing between these two modes of materials transport is to investigate the creep rate, i.e., the rate of material transport as a function of stress. For material transport by vacancy diffusion, the creep rate is proportional to the stress.' For creep by slip, controlled by dislocation climb, the creep rate is proportional to a power of the stress. For pure metals this power is 4.5;374 for dispersion-strengthened material a fourth power relationship can be derived.5 This difference in the stress dependence of the strain rate is illustrated schematically in Fig. 1, in which the logarithm of strain rate is plotted vs the logarithm of the stress for material transport in a pure metal by vacancy flux and by dislocation climb. The stress range in which the two types of material transport overlap would be expected to be relatively small. In the experiments described by Early and coworkers compacts pressed from spherical copper powder were sintered isothermally under an applied axial external load in a dilatometer. During sintering the magnitude of the applied external load was changed and the rate of axial shrinkage of the compact before and after the load change determined. In order to find the stress dependence of the strain rate the magnitude of the stress acting on the neck area between the spherical particles before and after the load change had to be calculated. This stress is the resultant of the stresses due both to the externally applied load and to surface tension. The stress due to surface tension is a function of the geometry of the powder compacts. It can be determined, at least for simple geometrical arrays,'76 but it is difficult to obtain exact values of the stresses for actual powder compacts when only average values of particle diameters and of neck diameters between particles are available. The calculation of stress and the strain rate-stress relationship is therefore only very approximate.

Jan 1, 1968

By Craig Faulkner

Discharge cones for large Semi Autogenous Grinding (SAG) and Autogenous Grinding (AG) mills are subjected to high wear as significant volumes of ground ore and slurry exit the mill. With the larger diameter mills of 32ft to 40ft in size becoming the norm, very high, concentrated wear is highlighting the limitations of conventional discharge cones and frequent changes are subsequently required. This paper outlines the advances made in the design of the Bullnose discharge cone. Superior wear materials to increase wear life over conventional rubber or chrome-moly steel discharge cones and the introduction of key design features to reduce reline times and improve fit and safety during installation, offer significant opportunities for the mill operator. Collated from multiple case studies, the wear data and reline history from 2004 to present clearly illustrate the way in which superior component longevity has reduced the frequency of relines over the life of the product to increase mill availability and effectively increase the tonnes milled in a period.

Jan 1, 2012

By Robert B. Hopler

Hercules Incorporated has developed and introduced a totally new non-electric delay blasting cap system which utilizes a low energy gas detonation to activate the caps. Unlike any other initiation system, there is no hole-to-hole connection other than empty plastic tubing until the blast is to be set off. Only at that time, when all personnel and equipment are in the clear, is the special gas mixture introduced through the tubing. The actual time of firing is completely under the control of the operator, by pressing the fire button on the blasting machine.

Jan 1, 1977

R F Johnston 1 ABSTRACT The possibilities for bacterial leaching of refractory gold ores found in the Central Victorian region of Australia are examined. The behaviour of bacteria, especially 77iobacillus ferroaridans is outlined and the effects of these when they are exposed to pyrite, arsenopyrite and stibnite are examined. The factors which are particular to Central Victoria are outlined and the possibility of adapting a bacterial culture to suit the conditions is discussed. It is concluded that a bacterial leaching system is a feasible proposition and that it could enhance leaching rates and yields.

Jan 1, 1994

By H. Firmstone

Deposits of cadmia, or impure oxide of zinc, are of common occurrence in the upper parts of blast furnaces using ores containing zinc, and were very common in the charcoal furnaces of Virginia working the brown hematite ores found near the Cadent black slate. These deposits were known to the old charcoal founders as "sulphur rings," and the characteristic green flame of burning zinc frequently to be seen at the tymp of furnaces working ores containing zinc, was held by them to indicate the presence of a "sulphur fall." When zinc is burning in considerable quantities at the tymp, the

Jan 1, 1879

By Hans Hamrin

Three drill-blast cycles of 3.1 m advance achieved in one working shift of 7.5 hours at the Holsfjorden Tunnel project in Norway. The tunnel, 5235 m long, with a cross section of 8.6 m2, was completed several months ahead of schedule. This remarkable performance was achieved by a crew of 16 men, using machines specially designed for small tunnel excavation. The integration of drilling and charging into one unit, mucking and transport in another, reduced non-productive time considerably. The average cycle time of 140 min made it possible to complete three rounds in one 7.5 hours shift.

Jan 1, 1987

Pyrite is one of the principal Au-bearing minerals in refractory gold ores. Significantly high Au concentrations of up to 5200 ppm are present in pyrite. Pyrite hosting high levels of Au is also enriched in As. Pyrite as an unwanted mineral ends up in wastes and constitutes one of the primary sources of As in the mining and metallurgical wastes. Arsenic can be readily released to the environment due to rapid oxidative dissolution of the host pyrite under atmospheric conditions. In order to determine the form and occurrence of arsenic in pyrite, micro-X-ray absorption fine-structure spectroscopy (XAFS) spectra were collected from a range of arsenical pyrite grains having different morphologies and a range of arsenic and gold concentrations. All the pyrite grains are characterised by the dominant edge aligned with As-1 valence state. In pyrite, arsenic atoms substitute for S atoms that are in six-fold coordination about each Fe atom. XAFS data suggest that As atoms occur in clusters within the pyrite structure. In addition to As-1, fine-grained, inclusion-rich and framboidal-type pyrite grains have a second As species at ~11 875 eV corresponding to As5+. This As5+ species in pyrite is highly variable and attributed to the oxidation of arsenic exposed on the surfaces of pyrite.

Jan 1, 2008

By K. A. Allison, D. R. Van Orden, R. J. Lee

Continuing analysis of environmental samples for asbestos content has resulted in the misidentification of non-asbestos amphibole particles as asbestos fibers. These errors have received wide publicity (such as in the asbestos-in-crayon story) and have caused unnecessary reformulation of products. The primary cause of these errors has been a poor understanding of mineralogy and analytical techniques among the many asbestos laboratories that arose following the passage of the AHERA regulations. Presented here is a procedure based on published data that can be used to correctly classify an elongated particle as asbestos or as non-asbestos.

Jan 1, 2005