Search Documents

By E. W. Henderson

Development work in the state of Utah in 1935 consisted of additional work done on wildcat tests started in previous years and on a number of new wildcat tests started during the year. No effort was made to extend areas or to discover deeper productive horizons in proven fields. Principal areas of development were in Daggett County, northeastern Utah; Grand and Emery counties, east-central Utah; and in Washington County, southwestern Utah. Daggett County Clay Basin.—The Mountain Fuel Supply Co. deepened Murphy No. 2, sec. 21, T.3N., R.24E., from 6030 to 6790 ft. for a test of the Sundance formation. Two sandstone members at 6520 to 6644 ft. and 6737 to 6790 ft. contained water. The hole was plugged back to 5860 ft. and left as a future gas supply for the Salt Lake City-Ogden pipe line. The failure of the Sundance formation to produce in this test, in view of the recent Sundance discoveries in Colorado arid Wyoming, was disappointing Emery County Last Chance.—-Thc wildcat test of the Rainsey Petroleum Corporn-tion, Well No. 1-X, sec. 18, T.26S., R.7E., completed plugging back from total depth of 3168 ft. to 2771 ft. and was shut in as a gas well. A gas sand at 2724 to 2771 ft. produced approximately 21 million cubic fert. A deep test of the structure will be started upon approval of a wit plan of development. Grand County Cisco.—-The wildcat test of the Utah Southern Oil Co., sec. 33, T.22S., R.22E., of which the total depth was 1720 ft. on Dec. 31, 1935, is the most interesting operation ill the state. Location of the test was deter-

Jan 1, 1936

By E. W. Henderson

Development work in the state of Utah in 1935 consisted of additional work done on wildcat tests started in previous years and on a number of new wildcat tests started during the year. No effort was made to extend areas or to discover deeper productive horizons in proven fields. Principal areas of development were in Daggett County, northeastern Utah; Grand and Emery counties, east-central Utah; and in Washington County, southwestern Utah. Daggett County Clay Basin.—The Mountain Fuel Supply Co. deepened Murphy No. 2, sec. 21, T.3N., R.24E., from 6030 to 6790 ft. for a test of the Sundance formation. Two sandstone members at 6520 to 6644 ft. and 6737 to 6790 ft. contained water. The hole was plugged back to 5860 ft. and left as a future gas supply for the Salt Lake City-Ogden pipe line. The failure of the Sundance formation to produce in this test, in view of the recent Sundance discoveries in Colorado arid Wyoming, was disappointing Emery County Last Chance.—-Thc wildcat test of the Rainsey Petroleum Corporn-tion, Well No. 1-X, sec. 18, T.26S., R.7E., completed plugging back from total depth of 3168 ft. to 2771 ft. and was shut in as a gas well. A gas sand at 2724 to 2771 ft. produced approximately 21 million cubic fert. A deep test of the structure will be started upon approval of a wit plan of development. Grand County Cisco.—-The wildcat test of the Utah Southern Oil Co., sec. 33, T.22S., R.22E., of which the total depth was 1720 ft. on Dec. 31, 1935, is the most interesting operation ill the state. Location of the test was deter-

Jan 1, 1936

By W. L. Hollinshead, Alwin Poltinger

GENERAL Tunneling by hand digging is as old as the history of humans. Mechanized tunneling did not begin to replace manual methods until around the beginning of the 19th century(Brunel patent, 1818). It brought with it a higher degree of safety for the workers and a much higher rate of boring. But for any kind of tunneling, an accurate and feasible method of survey must be accomplished during mining. That means, that for each tunnel project the most efficient survey method must be devised. The method to be defined depends on the spatial curve, diameter, speed of tunneling method, purpose of tunnel and contractual accuracy. The final accuracy of a finished tunnel is heavily dependent upon three critical elements: 1. Quality of the above ground survey 2. Tunnel traverse and directional transfer from above ground 3. Guidance for the mining job. Combining The Survey And The Guidance System Since the guidance system (GS) is one of the critical factors in the determination of the tunnel final accuracy, it is necessary to analyze how the directional control and tunnel traverse measurements can be effectively integrated into a GS. Any guidance system, whether manual or high technology, must continually detect and compensate for movement of its theodoliteor laser station standpoint. Movement beyond a preset allowable amount must generate a warning or error message to the user. Additionally, optical refraction can interfere with the results. Refraction will have an effect on any kind of optical GS. Therefore, careful selection of target and standpoint locations can minimize, but not completely eliminate, the influence of refraction. Some GS technologies, such as Gyro-based systems, are immune to the effects of refraction, but have other, methodical errors which will be described later in this paper. GUIDANCE Overview Why is a guidance system necessary? A GS, whether manual or automatic, compares the design direction and slope of a tunnel with the current position of the mining

Jan 1, 1997

By J J. Jiang, M Reimnitz

The Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston Open Pit is mining through a dense network of disused level workings and open stopes of greatly varying sizes. The condition of the stope crowns and remnants is often unknown, and ultimately these structures become a significant proportion of the production floor and pit walls. Significant seismic events and occasionally rock bursts often occur in the underground workings. Seismicity is becoming an issue to the viability of the KCGM Fimiston operations. KCGM needs to take a leading role in understanding mine-induced and regional seismicity. The seismic system trials were initiated in the Fimiston Open Pit in 1996 using the ISS system. The initial system included two triaxial geophone arrays and two triaxial accelerometer arrays installed into two boreholes. The main objectives of the trial were to investigate the suitability of the two types of sensors and the detectability of seismicity in the pit. The trial was regarded as a success and the system has been expanded and improved. The current system consists of 12 triaxial geophone and accelerometer arrays and nine uniaxial geophones. The 12 triaxial arrays are installed in nine boreholes drilled from the pit and the nine uniaxial geophones are installed from underground level workings about 660 m below the original surface elevation. The system is designed to provide seismicity coverage for the entire pit area that is about 2.7 kilometres long, 1.5 kilometres wide and about 300 metres deep. The accuracy of the source location has always been a challenge due to the existence of the dense concentration of stopes and lack of the sensors. It is uncommon to have direct ray path for the seismic waves to propagate to the sensors across the strike, hence sensors have been located along strike and under the old workings. This paper discusses some of the challenges associated with seismic monitoring near mine remnants and seismically active faults. The results of the seismic monitoring are presented, and contrasted to results of three dimensional boundary element numerical modelling. The impact of the seismicity upon pit slope stability is briefly discussed.

Jan 1, 2003

Notices THE FEDERATION OF SOCIETIES OF PROFESSIONAL ENGINEERS It is expected that the National Institute of Personnel Research will be conducting a project, at the request of the Federation, to establish the relationship, if any, between the academic and professional achievements of engineers. co-operate with the researchers. INFACON 74 The National Institute for Metallurgy, the South African Institute of Mining and Metallurgy, and the Ferro Alloy Producers' Association of South Africa will hold an International Ferro-alloys Congress in Johannesburg from 22nd to 26th April, 1974. INTERNATIONAL PLATINUM SYMPOSIUM OF THE SOCIETY OF ECONOMIC GEOLOGISTS The above symposium is to be held at the U.S. Geological Survey, Denver Federal Center, Denver, Colorado, from 13th to 17th October, 1975. Papers up to 40 doublespaced THIRD MEETING-CANADIAN HYDROMETALLURGYGROUP The Hydrometallurgy Group of the Metallurgical Society, Canadian Institute of Mining and Metallurgy, will hold its Third Annual Meeting, October 1 and 2, 1973, at Edmonton Alberta. COLLOQUIUM ON THE CONSTRUCTION OF SLIMES DAMS The Institute has arranged a two day colloquium on the above topic, to be held on November 14th and 15th, 1973, at Kelvin House. The following Programme has been arranged:

By J. B. Agan, R. J. Fernandes

This paper utilizes the layered-system approach, modified to include areal sweep efficiency, to determine the miscible-slug size required and to predict the perfort7zance of a miscible-slug process in a highly stratified reservoir having a permeability variation of 0.76. The slug size in each layer was determined from theoretical calculations and laboratory data which showed that, to maintain miscibility in the reservoir, the slug size had to be 8.2 per cent of the floodable hydrocarbon pore volume. Economic considerations, however, such as the value of the miscible product injected, the cost of injection and the cost of reprocessing the miscible product, limited the amount of miscible product which could be injected into the lower-permeability layers. This resulted in subjecting only 60 per cent of the reservoir to a slug size sufficient to maintain miscibility. Utilizing the relationship of producing gas-oil ratio and areal sweep efficiency as a function of pore volume injected (as obtained from data published by Dyes, Caudle and Erickson2), the theoretical performance was determined. This prediction is compared with actual performance to date. Actual performance reflects an increasing percentage of tniscible product in the produced fluid to a particular level, which remains static for a short period and then increases again to a higher level. This performance suggests that the reservoir has performed as a layered system. It is concluded that the layered-system approach can be used to predict performance in a highly stratified reservoir and that economic consideration is a limiting factor in determining the amount of the reservoir which can be miscibly swept. INTRODUCTION The Paloma zone in the Paloma oil field, Kern County, Calif., is comprised of several sand members separated by siltstone, shale and/or cherty sections. Rapid facies changes within the zone indicate that the sediments were deposited in a "near shore" environment. As a result, the Paloma sands have a high permeability variation, and the Paloma zone is comprised of several sand reservoirs. Since one of the sand reservoirs containing crude oil was not receiving the benefits of gas injection, consideration was given to recompleting certain wells to isolate the sand in order to perform a miscible-phase injection project and, thereby, to increase its ultimate oil recovery. Before proceeding with the project, a review of the literature was made to determine the miscible-slug size that would be required to maintain miscibility throughout the displacement process. Although the review showed that considerable information was available for homogeneous systems, insufficient information was available to determine slug-size requirements and to predict performances for a highly stratified reservoir. This paper has been prepared to describe the method used to determine the miscible-slug-size requirement and to predict the performance of the miscible-phase injection project initiated in the Paloma oil field. Although the Paloma project has only been in operation since Aug., 1958, sufficient production history has been obtained so that a comparison can be made with the predicted performance. DESCRIPTION OF RESERVOIR The reservoir in which the miscible-phase project was initiated in the Paloma field is shown on Figs. 1 and 2. Reservoir properties are as follows: average sand thickness, 43 ft; porosity, 19.1 per cent; water saturation, 47.2 per cent: oil viscosity, 0.328 cp; reservoir temperature, 250°F; reservoir pressure, 3,500 psi: gas saturation, 21.2 per cent at time of miscible product injection; and total net hydrocarbon pore volume, 19,993,000 reservoir bbl. LIMITATIONS The method described herein utilizes a layer-system approach, where injection into and production from each layer is assumed to be proportional to the layer's fractional capacity. The effects of increased fluid mobility on injection and production rates, in layers which have had breakthrough, are not reflected in this method. There has been considerable controversy over the slug size necessary to maintain miscibility throughout the displacement process. In this method, the slug-size

By R. M. Rose, D. P. Ferriss, J. Wulff

The effect of orientation on the stresses, nctivation energies, and activation volumes for yielding and plastic flow of tungsten single crystals was investigated. Tensile tests showed the proportional limit to be a function of orientation: crystals whose tensile axes were near the [I10} direction were roughly three times as strong as [loo] crystals. The [ 1101 crystals showed low strain hardening and displayed yield phenomena, whereas the other orientations yielded smoothly and showed considerable strain hardening. The fracture mode was cleavage, except for crystals near the [1101 , many of which gave "chisel" fractures at 300°and 373°K. The activation energy for yielding was approximately one- half an electron; volt at all orientations, and the volume of activation was (12 to 14)b3, except near the [1101, where it was 7b3. Activation volumes generally increased after yielding. The most common theoretical models for yielding and strain hardening of bcc metals were. found to be insufficient to the intepretation of the observations here in. An explanation is proposed, based on the dislocation reaction dislocation networks and jogs, md jogs formed during plus tic flow. PRECLSE knowledge of the Drocesses involved in the yielding and plastic flow of the refractory metals is essential to the formulation of models for their flow and fracture. Despite this need, the single -crystal investigations, especially of tungsten, have been sparse. Slip occurs at low temperature, according to schadler,i in <111> directions on {110) planes; as the temperature rises to room tempera-

Jan 1, 1962

By Henry F. Cooper, Scott E. Blouin

Large jacking test procedures that have been applied to obtain static in-situ rock properties (Ref. 1) have shown that the in-situ rock modulus and strength can be considerably less than what would be obtained from laboratory tests on intact samples. This trend is also expected to be true for dynamic properties, but few dynamic in- situ rock property tests have been conducted. During the past several years, high explosive test procedures have been developed to simulate the airblast and direct induced ground motions (Ref. 2) produced by nuclear explosions . These test procedures load large volumes (up to 10 7 f t3) of the earth with stress levels sufficiently high to produc5 feet of particle displacement over surface areas up to l0 5 ft2. This paper discusses some of the data obtained, and the implications of these results for our understanding of the dynamic response of in-situ rock. DESCRIPTION OF TEST PROCEDURES As shown in Fig. 1, the High Explosive Simulation Technique (HEST) consists of a cavity of uniform height bounded on the sides by a soil berm, above by an overburden of uniform thickness, and below by the test bed on the earth&apos;s surface. Horizontal racks of detonating cord are placed in the cavity and detonated at one end of the test bed. This detonation produces an explosive wave that propagates across the test bed, loading the earth with an overpressure pulse that decays with time because of the compression and lifting of the overburden. Since 1964, there have been approximately 40 such tests on test bed areas ranging from a few hundred to l0 5 sq ft., simulating peak overpressure conditions between about 100 and 6000 psi and specific impulses between a few and over 100 psi-sec.

Jan 1, 1971

By K L. Brown

In the Waiotapu geothermal area only Champagne Pool, 109 ng/L, and Waiotapu Geyser, 7.6 ng/L, have dissolved Au concentrations greater than 5 ng/L and most springs have concentrations less than 2 ng/L. When Au concentration data are combined with other physico-chemical data from each spring including; pH, reduced sulphur concentration and temperature, the degree of Au saturation can be calculated. All samples sites except Champagne Pool, Waiotapu Geyser and the Artists Palette are under-saturated with respect to Au(s) by 1 to 3 orders of magnitude. This indicates that adsorption or co-precipitation or both are important processes depositing Au beneath hot springs. Deposition of Au by adsorption or co-precipitation beneath hot springs implies that dissolved Au may not have to reach saturation concentrations for ore to deposit. This interpretation is supported by the presence of substantial Au as sub-microscopic components within sulphide minerals in ore deposits and indicates depositional efficiency beyond that possible through precipitation of Au(s).

Jan 1, 2004

By M. Mills, M. W. Clegg

This Paper Presents an approximate analytical solution to the problem of the pressure distributions arising from the production of a compressible liquid in a partially penetrating well. The limits of validity of the approximation are discussed and it is shown that the basic approximation is the same as that used in previous numerical of the problem. The variation in pressure at the production well with time for different penetration ratios is investigated and is shown to agree with previous work. The solutiOns are used to assess the effects of partial penetration at large distances from the well and at the wellbore itself. In the latter case the effects of anisotropy are also studied for constant, but unequal, horizontal and vertical permeabilities. It is &apos;uggested that measurements of the Pressure drawdown below the producing interval in a well should give some indication of a thickness-vertical permeability product for the formation; this would chmacterize the effectiveness of the formation below the producing interval. INTRODUCTION In many oil and gas reservoirs the producing wells are completed as partially penetrating wells; that is, only a portion of the pay zone is perforated. This may be done for a variety of reasons, but the most common one is to prevent or delay the intrusion of unwanted fluids into the wellbore. This paper studies the effects of partial penetration on the pressure distribution resulting from the production of a compressible liquid at a constant rate. To simplify the mathematical analysis the case of a single well located in an infinite reservoir of constant thickness is considered, and it is assumed that this well is perforated over an interval adjacent to the upper (or lower) impermeable boundary of the formation. A well producing from an arbitrary interval within the bulk of the formation could be treated in a similar way, but this action would merely add to the complexities of the solution and contribute little to the appreciation of the over-all effects of partial penetration. In a recently published paper by Odeh,10 the more general problem of producing from an arbitrary interval within the pay zone was studied for the quasi-steady state flow of a compressible liquid, This is the case in which there is a a potential at the outer boundary and a constant flux across the same boundary. This contrasts with the problem studied here, which is concerned with the nonsteady-state behavior in an infinite reservoir. The exact solution of the partial penetration problem presents great analytical problems because the boundary conditions that solutions of the partial differential equations must satisfy are mixed; i.e., on one of the boundaries the pressure is specified on one portion and the flux on the other. This difficulty occurs at the wellbore, for the flux over the nonproductive section of the well is zero, and the potential over the perforated interval must be constant. In the case of constant rate production from the well, this uniform potential is time dependent and unknown, and the additional condition that where hl is the thickness of the perforated interval, must also b&apos;e satisfied. This problem may be overcome in the case of constant rate production by making the assumption that the flux into the well is uniform over the entire perforated interval, so that on the wellbore the flux is specified over the total formation thickness. This approximation naturally leads to an error in the solution since the potential (pressure) will not

Jan 1, 1970

By Marek Wilczewski, Kristine Uhlman, Darrel Sipe

With the end of active copper mining in 1983, the extensive underground mine workings and the Berkeley Pit, one of the largest open-pit mines in the United States, began to flood. Daily in- flow to the pit is about five million gallons per day, with the water level rising at a rate of 30 feet per year. To support the remedial investigation and feasibility study, a six-layer, three-dimensional MODFLOW-based ground water flow model was constructed to simulate the 9,100-acre site. The vertical domain of the model extended over 1,060 feet of elevation difference and consisted of a finite difference grid of 89 rows by 54 columns. All work was PC- based. Model boundaries were assigned to correspond to natural hydrologic features such as geologic contacts, faults, and surface water features. The fully calibrated model was approved by the State of Montana and the U.S. Environmental Protection Agency (EPA) for use in the site remediation. The computer model was used to determine ground water flow velocities and contaminant travel times within the alluvial sediments adjacent to the Berkeley Pit. The purpose of the model was to predict future alluvial ground water flow directions should acid- and heavy metal-laden flood waters filling the Berkeley Pit rise up and enter the Alluvial Aquifer.

Jan 1, 1996

Recent well-publicised problems with the start-up of new mining projects have continued to feed the perception that the mining business in general and Ore Reserves in particular are a poor risk. New mines commonly experience difficulties when the true variability of ore characteristics becomes apparent during commissioning. At this critical stage, the impact of lower metal recovery, reduced throughput or increased consumption of reagents and energy can have a catastrophic effect on economic returns, as illustrated by the premature closure of some operations. There appear to be several common reasons contributing to the poor performance of mining projects, of which three are examined here: lack of early risk assessment before feasibility studies are started, inadequate sampling for metallurgical test work and variability of the run-of-mine (ROM) ore. An underlying feature of these issues is the lack of effective interaction between geologists, mining engineers and metallurgists/ process engineers. Geologists need to be more aware of ore processing issues and the range of characteristics that need to be considered as part of the resource estimate. Metallurgists need a greater understanding of the variability of the run of mine ore in terms of all the characteristics that influence the design and operation of the plant. Mining engineers need to determine the short-term variability of the ore in the mine schedule, so that there is confidence that the quality of the run-of-mine ore will be within the design specifications of the plant. A substantial overlap between these disciplines and sharing of areas of responsibility is necessary if these and other technical problems are to be better understood, production estimates are to be improved and commercial risks are to be reduced. Although the JORC Code (1999) provides guidelines for reporting all the issues that are material to an Ore Reserve estimate, some issues are rarely fully addressed in Ore Reserve reports. In particular there is no formal requirement for a metallurgist to assure his or herself of the appropriateness of the Ore Reserve classification. Consequently the level of uncertainty related to recovered grade and ore processing characteristics may be understated. It is suggested that to meet the concerns of bodies funding new mineral developments a stronger multi-disciplinary approach to the analysis of mineral deposits and reporting of Ore Reserves is required. The culmination of this approach would be the formal requirement for a geologist, mining engineer and a metallurgist to co-sign Ore Reserve reports.

Jan 1, 2002

By Charles M. Rolker

The main tin-producing regions of the world are known to be England, Australia and the Dutch East Indian possessions, chiefly Banca and Billiton. During recent years, the tin of the Malay Peninsula, exported from Penang and Singapore, has been coming prominently to the front. France, Austria, Hungary, Germany, Spain, South America, Russia and China still present insignificant figures. The conspicuous part which the Dutch possessions in the Indian Archipelago have taken in supplying the world with tin, is well known. Tin was discovered in Banca as early as 1710, and has been produced there ever since; but the supply has been most important since Banca came fully into the possession of Holland, in 1821. In Billiton and the adjoining island of Singkep, the existence of tin was known prior to 1822.* The Lingganese knew of its existence in the valley of Embalong, from creeks and streams in the neighborhood of Tima and Simper hills, on Billiton and also on Singkep island, but the prevailing superstition that tin-mining brought misfortune, influenced them to let this industry lie idle. The attempts of the Dutch government to test this question were lukewarm, perhaps by reason of the fear of reducing, through new discoveries, the price of Banca tin, and the island was abandoned in 1826, leaving only a military post. In 1850, Dr. Crookewit, a chemist and naturalist, was sent out to verify the rumors that tin existed in Billiton. His report was unfavorable; but in 1851 Mr. C. De Groot, a mining engineer, found tin readily, and the active work on Billiton dates from that time. Less than 600 tons were produced during the first ten years, and 3000 tons in the next decade. Billiton tin-mining is done by

Jan 1, 1892

By H. Hanemann

THE application of other than mechanical methods to the study of the mechanical-physical properties of metals has become in the last few years a topic of investigation of ever-increasing interest, both from the theoretical standpoint and from that of the engineer and constructor. Besides the investigations which have been made of &apos;the magnetic properties of ferromagnetic metals, in their relation to the mechanical properties of these metals, which will be discussed more in detail below, there have been made studies of other phenomena in the same relation, and methods for the mechanical testing of metals have even been suggested, for example, the microscopic method of Tammann,1 and the thereto-electric, method of Turner2 for determining elastic limits. The application of all such methods, which are based upon the dependence of some physical, crystallographic, or possibly chemical property, upon the mechanical state of the metal, must be preceded by close and careful correlation of these various "test" properties with the known mechanical state of the different metals or materials. It is with this view that the present work, as well as that of many previous investigators of, what .may be termed in the interests of brevity, the mechanical-magnetic properties of ferromagnetic materials of construction, has been done.

Jan 12, 1915

By R. L. Perrine

A stability theory is developed for miscible liquid-liquid displacement within a porous medium. In the usual case considered, a high-density high-viscosity "oil" is displaced downdip by a low-density low-viscosity "solvent&apos;! Perturbation methods are used to find the conditions under which the spreading mechanism changes from the stable dispersion process to unstable viscous fingering. We find that instability is conditional, that there is a dependence on the shape of a disturbance leading to a"diameter" effect and that very difficult experimental scaling problems may result. A useful consequence is the definition of a minimum "slug size" for stable miscible displacement. This should make possible optimum use of the solvent process for oil recovery. The results may apply to many situations in which one fluid displaces another of somewhat different fluid properties within a porous medium. INTRODUCTION The process of miscible liquid-liquid displacement looked very favorable when it first received serious consideration as a means to increase petroleum recovery. Some early laboratory results were interpreted to mean that only a small "slug" of solvent was needed, perhaps 2 to 3 per cent of a hydrocarbon pore volume. This "slug" could recover the oil in an entire reservoir provided the fluids remained miscible.1,2 Only a slow growth of the "mixing zone", or gradual transition from oil to solvent, should occur. This would follow naturally from mixing by a dispersion mechanism such as that described by Scheidegger.3 And, indeed, laboratory cores have shown this kind of behavior provided solvent viscosity was at least as great as that of the oi1.2,4-6 The same kind of behavior has also been observed with solvent viscosity lower than that of the oil after the distance traversed became large. Not all laboratory results have been this favorable, however.7-9 Mixing zone growth may become proportional to the distance traveled rather than the square root of this quantity. Such behavior accompanies high rates in short systems of large diameter, provided the viscosity ratio is adverse. If this more rapid spreading were to persist in a reservoir, the solvent requirement for miscible "slug" displacement could exceed 30 per cent of a pore volume. There is considerable economic importance in the difference between 3 and 30 per cent solvent. A 1ogical conclusion is that two different kinds of flow behavior are possible, with each kind leading to a different result. One kind gives efficient displacement, the other does not. In the efficient case, the solvent bank spreads out only by the mechanism we have termed dispersion. Under these conditions, displacement is as near piston-like as possible. In the second kind of flow, found only with adverse viscosity ratios, viscous fingering occurs. That is, permeability variations cause a small finger of low-viscosity solvent-rich fluid to move ahead of its average position within the mixing zone. This creates a path of low resistance to flow, and an even greater amount of solvent-rich fluid follows. Thus, the process is autocatalytic. Once started, the fingering mechanism rapidly becomes dominant. The question to be answered is this. Under what conditions will each of these two different kinds of flow occur? In particular, what conditions denote the transition from dispersion to viscous fingering as the solvent spreading mechanism? The answer may tell us whether or not the desirable, near piston-like miscible displacement process is practical. An answer to this problem can be obtained from theory by the use of perturbation methods. The procedure is as follows. We first formulate a mathematical representation of the system. Then a small disturbance (or perturbation) in solvent concentration profile is introduced and observed to see what happens. Unstable flow is indicated when a small disturbance will grow larger. This will lead to eventual viscous fingering. If on the other hand the disturbance dies out, the displacement is stable. In this latter case, with dispersion as the spreading mechanism, near piston-like displacement is possible. Thus, this paper presents the development of a stability theory for miscible liquid-liquid displace-

By Charles Joyce, William C. Burkle, Dan Murphy

Rare indeed has a major cross country natural gas pipeline met and surmounted such obstacles as the Iroquois Gas Transmission Line from Canada to Long Island, New York. Of the 370 miles long length a fair estimate has been that 1/3 or 122 miles were across rock country. Spread One, Four and Five were particularly difficult. If is estimated that over 75% of the required blasting was on those three spreads. The term "spread" goes back to the old term of describing a ranch.

Jan 1, 1992

By S. Balideh

A good understanding of the behavior of broken rock helps to make more informed decisions regarding slope stability and waste dump issues in mines. The cohesion coefficient of rock has little influence on the strength of broken rock; therefore, a criterion based on friction and cohesion of intact materials does not provide an accurate analysis for the strength of broken rock. This paper illustrates the effective strength of broken rock through a brief literature review about failure of intact rock and rock masses. The complete stress- strain curve and some important points of residual strength of rock are summarized in this paper.

Jun 1, 2012

By K. Vaxevanidou

A combined chemical and biological treatment for the removal of heavy metals and arsenic from a contaminated soil was studied as a potential method for soil remediation. Small scale and column tests were conducted in order to ex-amine the effect of plant-compost and Na2CaEDTA addition on a calcareous soil highly contaminated with heavy metals and arsenic. EDTA is known to be an efficient leaching agent of heavy metals from contaminated soils but has no effect on arsenic. Compost tea on the other hand contains humics that can leach several iron compounds including Fe(III)-oxides and thus can extract arsenic bound to these oxides. The action of Fe(III)-respiring bacteria D.palmitatis was also evaluated for the reduction of iron oxides and compared to simple chemical treatment in the presence of compost in small scale tests. Results indicated that the addition of compost and EDTA into soil pulp lead to the predominance of reductive conditions and the simultaneous dissolution of both heavy metals and arsenic at high percentages. The presence of D.palmitatis did not further enhance the reductive dissolution of Fe(III)-oxides by compost and EDTA as it was observed in the inoculated samples. Column tests using soil as received revealed that, although the extraction of metals seems to be a slow process, compost is an effective oxygen barrier that promotes the reductive dissolution of iron oxides and the subsequent arsenic release together with the dissolution of heavy metals by EDTA.

Jan 1, 2005

The members of the Institute will recall the account given in the March Bulletin of the inauguration exercises of the Engineering Foundation which was inhibited by an initial gift of $200,000 by Mr. Ambrose Swasey, to be administered by the United Engineering Society as trustees. The Engineering Foundation Board is now constituted as follows: GANG DUNN, Chairman, EDWARD D. ADAMS, Vice-Chairman FREDERICK R. HUTTON, Secretary, JOSEPH STRUTHERS, Treasurer, American Society of Civil Engineers. J. WALDO SMITH, CHARLES WARREN HUNT.

Jan 12, 1915

By R. Noriega, M. Suazo, V. Murariu

Current AG and SAG mill circuits have continued the trend to larger, fewer mills. These large mills place a significant additional load on the discharge systems and it has become imperative that the designs of these mill discharge systems are evaluated carefully to ensure maximum efficiency and have the capacity to be able to handle the increased mill discharge volumes. The current generation of multiphysics modeling tools allow a detailed analysis of AG and SAG mill discharge performance. The combination of Discrete Element Method modeling and Computational Fluid Dynamics allows the designer to model in detail all aspects of a mill discharge performance. This includes a detailed description of the build-up of solids and slurry in a mill discharge, the recycle of material back into the mill through the grates, the relative wear rates and the occurrence of overloading at the pinch points. These tools allow intelligent decisions to be made regarding the type of discharge arrangement, pan lifter geometry, and discharge cone design, so as to ensure that the discharge is capable of handling the duties required for a specific installation. This paper details the current state of the art in these modeling tools, and provides an overview of some recent applications.

Jan 1, 2012