Search Documents

By Paul Headland

The Washington Suburban Sanitary Commission (WSSC) has recently completed design for the Bi-County Water Tunnel Project. The project will include a 10-foot diameter, 5.3-mile long hard rock tunnel located within the Piedmont Physiographic Province in Montgomery County, Maryland. The rock formations present along the alignment are comprised of igneous and metamorphic lithologies. This paper presents the steps taken to characterize the complex geology along the tunnel alignment into a single ?Engineering Unit? based upon the intact rock and rock mass properties. The Rock Mass Rating (RMR) system is planned to be used as the basis for dividing the ground into three ?Excavation and Support? classes. This RMR approach was selected to establish contractual baselines as presented in the Geotechnical Baseline Report (GBR) and is intended to facilitate management of the ground support characterization during construction.

Jan 1, 2008

By Chick Kerkering, Stephen Iverson

Perimeter control blasting is common in civil construction projects but not as common in mining. A poorly designed and executed underground mine development blast design can result in unwanted wall rock damage. This damage increases the risk of rock falls and injury. With the availability of good drilling equipment, it is a simple matter to add the few extra holes needed to change conventional drifting into drifting with perimeter control.

Jan 1, 2008

By C. Goldberg, R. H. Wynne

WHEN using an optical goniometer to determine crystal orientation' it is advantageous to use a preferential etchant so that the etch pits have plane faces which are parallel to crystallographic planes, all of which are of the same "form." "Westinghouse Silver Etch" (WAg), a preferential etch for germanium, is made up as follows: 40 ml of 49.7 pct hydrofluoric acid, 20 ml of 70.7 pct nitric acid, and 40 ml of distilled water containing 2.0 g of silver nitrate. Examination of metallographs of WAg etched surfaces (Fig. 1, for example) indicates that, regardless of crystal orientation, the faces of the etch pits are (111) surfaces. Optical goniometer examination of these WAg etched surfaces also indicates that the faces of the etch pits are (111) surfaces, i.e., all bright reflections are from (111) planes. When using an optical goniometer of the type described by Barrett,' not only (111) reflections from a WAg etched germanium surface but also other reflections of lower intensity will be observed. These latter reflections can cause confusion. We have used an optical goniometer made from a war surplus astrocompass and a galvanometer lamp. The reflections are observed by using the goniometer in a darkened room and letting the reflected light be in- cident upon a piece of white paper. The resulting decrease of goniometer sensitivity enables (111) reflections only to be observed. This in turn permits the crystal orientation to be determined in a matter of minutes, since only two measurements are necessary. The authors wish to acknowledge the help received from R. E. Davis who assisted in making the metallographs and aided the authors in the interpretation of the metallographs.

Jan 1, 1954

By M. R. Yalamanchili, C. A. Young, J. J. Kellar, W. M. Cross, J. D. Miller

Introduction Researchers have long speculated regarding the adsorption state of collectors on mineral surfaces. Only recently have analytical techniques become available that allow direct in situ analysis of adsorbed layers. With reactive internal reflection elements (IREs), Fourier transform infrared spectroscopy coupled with internal reflection spectroscopy (FT-IR/IRS) allows for unobtrusive investigation of the adsorbed layer (Harrick, 1979). This technique has been used both for the in situ identification of adsorbed species and for the direct calculation of collector adsorption density in real time from infrared spectral data (Miller and Kellar. 1988). The reactive mineral IRE serves both to internally reflect the infrared light and to act as a substrate at which collector adsorption can be monitored. Shown in Fig. I is a schematic of light being internally reflected in an IRE. As the light is totally reflected at the interface, an evanescent wave propagates a short distance (typically a few microns) away from the IRE, and sampling of the interfacial region occurs. Because of multiple internal reflections, great sensitivity can be obtained. Flotation systems for which this method has been demonstrated include CaF2/oleate, Al2O3/dodecylsulfate, CaCO3/oleate, ZnS/xanthate and KCI/octylamine (Miller and Kellar, 1988; Kellar et al., 1989, 1990; Miller et al., 1990). Of particular interest to flotation chemists is the conformational behavior of the alkyl chain of adsorbed collector molecules. In the simplest sense, conformation can bethought of as the relative flexibility of the hydrocarbon chain caused by rotations about carbon-carbon single bonds. The flexibility is described by the amount of gauche/trans conformations in the alkyl chain. Figure 2 shows examples of gauche and trans conformations (rotational isomers or rotamers) in a hydrocarbon chain. These two conformations are observed when the terminal methylene groups in any four-carbon subchain are on the same side (gauche) or opposites sides (trans) of the plane of the middle carbon-carbon bond. A gauche conformer (rotamer) is thus a state of maximum potential energy, whereas a trans conformer is a state with minimum potential energy. The difference between these states has been found to be approximately 0.5 to 0.8 kcal/mole (Mead et al., 1986). The relative number of butane molecules present as gauche conformers with respect to trans conformers can be calculated from the Boltzmann equation (Mead et al., 1986). At 25° C approximately 66% of the butane molecules are trans rotamers. [ ] However at 100° C, only 33% of butane molecules are trans rotamers. Exposing the hydrocarbon chain to a polar, rather than an a polar, medium should also cause an increase in the number of gauche butylene groups in a hydrocarbon chain, although this effect has been difficult to observe experimentally (Mead et al., 1986). Forming a crystalline hydrocarbon is equivalent to decreasing the temperature, which greatly increases the amount of trans butylene groups present in the chain. From the preceding discussion, a picture of the solution species of concern can be developed. The collector monomer should exhibit the greatest number of gauche rotamers and most likely will look crumpled or balled-up to reduce the surface area in contact with water. The micellar form is expected to be aggregated, with the hydrocarbon chain existing in a less polar environment. These characteristic conformational features have been examined by FT-IR spectroscopy for various liquid phases of alkanoic acids (Umemura et al., 1981; Cameron et al., 1982a; Yang et al., 1986; Wong, 1987; Wong and Mantsch, 1983; Cross et al., 1992), phospholipid membranes (Fringe Ii, 1980; Casal and Mantsch, 1985: Wong et al.. 1988;

Jan 1, 1994

By B. Hilscher, P. Nayak, N. Yoon

"The mining industry is currently facing challenges with declining feed grades and is struggling to find solutions to improve the project’s economic value. By means of pre-concentration, ore sorting aims to separate the barren material from the valuable ore to reduce energy consumption and tailings generation, while increasing the feed grade, concentrate grade, mill recovery, and revenue. In addition, ore sorting allows the modification of deposit geometallurgy in order to allow the creation of an optimal mill feed.This paper evaluates the applicability and challenges of ore sorting by utilizing the results from four different mines, and reviews them in detail. The mines include two underground and two open pit mines that are base metal and precioius metal operations. In order to understand the applicability of ore sorting in these operations, initial rock-by-rock test results and different types of assays (atomic adsorption [AA], inductively coupled plasma [ICP], and fire assay) are utilized. Using the assay results, the grade recovery curves for ore sorting are generated and they are further improved by using and developing an ore sorting algorithm, which is discussed in this paper. The application and evaluation of ore sorting in greenfield and brownfield properties will also be discussed.The state of the art ore sorting technologies for both rock-by-rock and bulk sorting are reviewed in this paper. The future technologies on the horizon, including different combinations of sensors, are explained. The sorting technologies include, X-ray transmission (XRT), X-ray fluorescence (XRF), colour, infrared, electromagnetic, and laser induced breakdown spectroscopy (LIBS).IntroductionOre sorting is a sensor-based sorting technique introduced between the excavation stage and processing stage, where the unwanted waste is diverted to the waste dump and only the ore is sent to the mill for further processing. As a result, the quality of the material entering the mill is improved and the dilution of the ore is reduced. In greenfield projects, sensor-based ore sorting provides an opportunity to reduce the capital cost of the project and increase the return on investment (ROI). With most operations currently facing the challenge of finding a high grade deposit, having a sorting unit provides several advantages while keeping the cost at minimum."

Jan 1, 2017

By Keizo Uematsu, Satoshi Tanaka, Nozomu Uchida, Anze Shui, Joaquin Lira, Cyril Lavelle, Midori Saito, Thierry Poirier

"Dispersed and flocculated alumina (non-spherical particles) slurries were prepared by pH controlling with HCL Spray-drying of these resulted in dimpled granules with a smooth surface and high density, and spherical granules with rough surface and low-density, respectively. Detailed characterization on granules and their compacts includes: SEM observation, density measuring (mercury porosimetry and Archimedes's Principle) and liquid immersion optical microscopy. Compaction of these granules originated a larger particles rearrangement in the samples made with the spherical granules than with the dimpled granules. This was verified through the orientation of alumina particles, which was pronounced in the compact made with the former granules.IntroductionOn immersing a ceramic powder in water, the surface usually acquires a charge by interaction with ionic species in solution. The charge is affected by pH and the electrolyte concentration of the water. 1 The dispersion in a slurry is achieved through the interaction of charges on the particle surface with the media. In the ceramic processing, especially in the process of casting, the dispersion of slurry has been one of the most important topics studied for many years. Recently the attention is paid on its role in the pressing. The granule characteristics are governed by the dispersion state of slurry. Takahashi et al2 , Tsubaki et al3 and Walker et al4 showed that the granules from dispersed slurry were dimpled and of high density, while granules from flocculated slurry were spherical and of low density. This variation in the granules characteristics should have a marked effect on the structure of compact.This paper presents the influence of the dispersion state of alumina slurry on the granules characteristics and also on the internal structure of compacts. Different dispersion states were elaborated by adjusting pH of the slurry. In this method, the particles are dispersed or flocculated only by the effect of surface charging, and thus some secondary effect such as the steric hindrance from an electrolyte dispersant is avoided. The characteristics of granules and compacts are examined with SEM, density measurements by mercury porosimetry and by Archimedes's Principle and liquid immersion optical microscopy. This novel microscopy provides various important information on packing structure of particles, such as their orientation. 5"

Jan 1, 2000

By Hamid Maleki

The U.S. Bureau of Mines implemented a monitoring program in a western U.S. coal mine for the evaluation of both conventional and alternative support systems. The conventional support consisted of 2.5-m-long vertical bolts installed in an 5.5-m-wide entry. The alternative system consisted of 2.5- and 3-m vertical and inclined bolts installed at a higher density during widening of a cut from 3.6 to 5.5 m. Roof deformation, roof stress, rib deformation, and bolt loads were monitored during the 2-month test period. In addition, roof failure patterns and lithology were characterized within the six-entry main test section. Results were analyzed using roof deformation and failure profiles, roof stress profiles. bolt loading and bending moment diagrams, and numerical models. The mechanics of roof deformation, failure, and support reaction in three zones in the mine roof were characterized. Significant improvements were shown in roof stability in the section using the alternative system. Results are encouraging and indicate the effectiveness of alternative support systems and excavation techniques for limiting inelastic deformation of roof in highly stressed underground mines.

Jan 1, 1994

THE shipments of high-grade manganese ore, con-taining 35 per cent or more of manganese, from the mines in the United States in 1926 were slightly less than half as large as similar shipments in 1925, accord-ing to the United States Bureau of Mines, Department of Commerce. The shipments in 1926 by 45 producers amounted to 46,258 long tons as compared with 98,324 long tons by 42 producers in 1925. This decrease was due to the falling off of the shipments from Montana. The domestic production of metallurgical ore in 1926 was 26,530 tons; that of chemical ore, 19,728 tons. Montana was the largest shipper with 5713 tons of metallurgical ore and 17,904 tons of chemical ore. The largest individual shipper of metallurgical ore was the Crescent Mine in the Olympic Mountain Region, Clallam Co., Washington, from which the shipments for the year were 3162 tons. The mine was operated by lessees and reverted to the owners in July, and thereafter to the close of the year no .ore was shipped.

Jan 6, 1927

By P Hartlieb, M Noeger, M Varelija

Rock bolts are important in underground mining as they provide support to the rock mass around the excavation. They are the most common reinforcement method in mining and civil engineering excavations. The length of the bolts, types and spacing between them can be varied, depending on the reinforcement requirements and the use case (Kolapo, Onifade and Praise, 2022). The rock bolt provides safety and stability for the rock mass in the excavation area and they can be mechanically anchored, grouted, or friction anchored. They normally don’t have a measurement option and there is a possibility that it failed without showing visible signs on the surface, especially in grouted rebar bolts where they can still have some residual strength. Therefore, support functionality can be lost without recognising it. To overcome that, sensors can be installed on all three previously mentioned bolt systems. Intelligent bolts with implemented measuring systems have a function of showing changes and indicating if there is some damage on the bolt. So, it can be said that intelligent rock bolts are regular bolts equipped with additional instruments which are helping us detect potential instabilities inside of the rock mass or malfunction of the bolt itself. Changes in rock mass can be tracked, by measuring rock bolt reaction concerning the excavation response. Rock mass damage and instabilities are therefore measured in terms of rock mass deformation. Moreover, other additional information depending on the type of the sensor device could be collected. Based on such measurements, information about rock mass state can be derived. Different rock bolt types work at different reaction principles. Therefore, limitations on sensor application and information that can be extracted must be considered.

Sep 1, 2024

By Richard J. Mainiero, Harry C. Verakis

The Bureau of Mines has conducted research to determine whether the total elapsed delay time for blasting bituminous coal in underground mines could be safely expanded beyond the present 500-ms limitation without igniting a methane or methane-coal dust atmosphere. The results indicated that the increase of total delay from 500 to 1,000 ms had no detectable effect on safety relative to incendivity as long as permissible practices were observed in all other aspects. Research was also conducted to evaluate the safety of 18-in hole spacing for delay blasting in coal relative to misfires. For a variety of permissible explosives, misfires were observed for about 50 pct of the holes at 18-in spacing. Based on this observation, the Bureau has recommended that the new regulations prohibit hole spacings of less than 24 inches in underground coal mines. Misfires were also observed for 24-in spacing, but the number of misfires and test shots was too small to sup- port any firm conclusions.

By W. Tovote

This paper is based upon 12 years' experience in the Southwest, including three years that were spent in constant traveling as examining engineer for the Phelps-Dodge Corporation. The material was gathered during rather extensive work in Bisbee, Clifton-Morenci, Globe, and Tombstone, and also on short and rapid trips into most of the mining camps and prospect fields of New Mexico, Arizona, the desert country of California, and as much of Sonora as was safe at the time. My methods of observation and my deductions are not put forward as new or scientific; they are simply rough field methods, based upon short notes, rough sketches, and largely upon memory, which I have found useful for coördinating geological data for the purpose of passing quick judgment on mining possibilities in certain districts exhibiting uniform characteristics. The opportunities for observation have been better these last few years than ever before, due to the unprecedented activity in mining, which has caused the reopening of hundreds of old mines and the starting of even more numerous prospects all over the mining states. Possible Systems of Classification By Geological Provinces There are a number of well defined geological provinces in the territory under discussion, and a study of their individual features is of interest. The following are a few of those that are most striking in their uniformity. 1. The "Desert province," extending roughly from Wickenburg, Ariz., to and beyond Barstow, Cal. In its north-south extent it reaches up to the Colorado River and down into Sonora, but overlaps other provinces. It is characterized by a worn-down basement of schistose and granitic rocks, on which rest remnants of Paleozoic and pre-Paleozoic sediments, including very old limestones. The sediments are disrupted and contorted. Alteration in the mineralized areas is very prominent, especially in the schists and limestones. Cenozoic volcanic rocks, principally of semi-basic composition, have been intruded into this complex and sometimes cover it as lava flows. 2. The "Yavapai schist" province, similar to the one first mentioned, consists of metamorphosed basic and semi-basic rocks. It lies in northern

Jan 1, 1920

By Max Ball

AN intelligent discussion of the oil situation and its needs, whether from the standpoint of the prospector, the operator, the engineer, or the public administrative officer, must be founded upon a knowledge of the law under which oil lands are obtained. A consideration of new legislation must be prefaced by an understanding of the present law and its results. This paper undertakes to present no new remedy for the ills of the present situation, no new solution of the problems the oil business is facing. It attempts merely to summarize the present law, its provisions, its origin, its development, and its effects. The discussion does not pretend to be exhaustive from a legal standpoint. It aims to avoid legal intricacies Which tend to confuse rather than clarify. It seeks but to present the essentials of the existing situation. The title to government lands known to contain valuable deposits of petroleum may be acquired only under the terms of the placer law as embodied in Section 2329 et seq. of the Revised Statutes. As a preliminary to considering the desirability of this situation it is profitable to examine into its origin. ORIGIN OF THE LAW Congress has left no room for doubt as to the legal applicability of the placer law to oil lands. The Act of Feb. 11, 1897 (29 Stat., 526), provides: "that any person authorized to enter lands under the mining laws of the United States may enter and obtain patent to land containing petroleum or other mineral oils, and chiefly valuable therefor, under the provisions of the laws relating to placer mineral claims."

Jan 6, 1914

By M. Ng

As part of a long-term study of titanium minerals processing being undertaken by the Julius Kruttschnitt Mineral Research Centre, techniques have been developed to measure the resistivity of ilmenite, rutile, zircon and other associated minerals. The techniques have proven reproducible and have allowed the measurement of resistivity under conditions of varying temperature, surface condition and surface moisture adsorption. The measured values can be linked to the separability of the minerals in the dry plant, and hence are useful as a diagnostic test for existing plants when performance deteriorates, or for greenfield sites to investigate potential problems. One of the major problems in electrical separation of titanium minerals is surface coating on the mineral grains. Coatings can make normally conductive minerals such as ilmenite and leucoxene behave much more like non-conductors. Electrical separation of surface contaminated ilmenite from non-conductors then becomes extremely difficult unless the surface contaminant is first removed. The resistivity measurement technique was used to evaluate the effect of surface cleaning on the resistivity of ilmenite and zircon from a Western Australian deposit which will shortly be in production. Ten different attritioning methods were evaluated, ranging from simple rinsing inwater to chemical attritioning in sulphuric acid combined with ultrasonic leaching. A roasting and quenching step was also investigated. As would be expected, the gentler treatments, such as rinsing in water or Calgon, had only amoderate effect on the ilmenite surface coatings. Ilmenite resistivity decreased by about 1 order of magnitude from 5.6 x108?m to between 2.5 and 4.4 x107?m. More intense treatments had a much more pronounced effect. The most effective, reduced ilmenite resistivity to 6.5 x105?m or three orders of magnitude. Zircon was relatively unaffected by any of the attritioning methods, with only a small increase in resistivity observed from 8.0 x1012?m to 2 x1013 ?m. The results show that measurement of mineral resistivity allows the effect of surface treatments to be easily quantified in a way that has benefits for greenfield site development where only small samples are available for testing. The effect of surface moisture has also been investigated using resistivity measurements. Measurements were made on zircon in an environmental chamber in which both humidity and temperature could be closely controlled. Zircon resistivity at 60 deg C decreased from 6 x1011?m at 5% relative humidity to 8 x108?m at 95% humidity. Moisture content and moisture re-adsorption from dry of zircon and number of other minerals were measured using a Mettler moisture analyser. Zircon adsorbed the least amount of surface moisture (0.05–0.09%) but re-adsorbed moisture from dry the fastest, reaching 98% of the original level in 10 minutes. Leucoxene adsorbed the most moisture (0.67%), but was much slower re-adsorbing this moisture from the dry state, reaching only 63% of the original level in 10 minutes. The difference was attributed to the surface characteristics of the grains, the leucoxene being much more porous than the zircon examined. The resistivities and differing rates of moisture adsorption can be used to quantify the effects of changes in atmospheric conditions of the performance of electrical separation in dry plants.

Jan 1, 2003

By Knut L. Sandvik, Aage Solbakken

it is an established fact that the collecting properties of xanthates and anionic collectors are dependent on the hydrocarbon chain length. This is ascribed to the greater adsorption densities caused by increasing the xanthate chain length. As batch flotation tests showed similar trends for amines, an investigation of the adsorbing properties of amines was undertaken. Because earlier investigations showed adsorption densities for dodecylamine salts on quartz varying as much as 20 times under apparently similar conditions,1-4 it was decided to make a survey of the changes in adsorption density due to the drying conditions of the quartz. EXPERIMENTAL PROCEDURE The quartz, handpicked in the pegmatite quarries of Iveland, Setesdal, had the following composition: SiO2 99.81, A12O3 0.01, Fe2O3 0.05 and loss by ig-

Jan 1, 1969

By Johnson N. W, Ralston J, Lauder D. W, Smart St C R

The flotation behaviour of the Hilton ore of Mount Isa Mines has been examined in the presence of two collectors (sodium ethyl xanthate (Ex) and sodium diisobutyldithiophosphinate (3418A)) over a range of flotation Eh values and collector additions. Tests were also conducted in the absence of collector to determine the relative contributions of natural and self-induced floatability of the major minerals in the feed. In these tests the influence of metabisulphite on the self-induced floatability of the minerals was also determined. Attention focussed on optimising the selectivity of galena flotation. It is shown that the Hilton ore sample contained lower levels of naturally hydrophobic iron sulphide minerals than are generally contained in the Mount Isa lead-zinc ore. Furthermore, the self-induced floatability of galena was less than that exhibited by the galena in the Mount Isa lead-zinc ore. Sodium metabisulphite (MBS) reduced the self-induced flotation of galena but had no effect on the natural floatability of the iron sulphide minerals.

Jan 1, 1991

By Greg Rasmussen

"Huckleberry Mines Ltd is an open pit porphyry copper-molybdenum mining operation located 120 km south of Houston, British Columbia with a 18,000 tpd milling facility. Huckleberry Mines is owned 60% by Princeton Mining Corporation, the operator, and 40% by Japanese partners.The Huckleberry deposit is one of several porphyry systems located in the Tahts a district of the intermontane belt of British Columbia. The principal economic minerals are chalcopyrite and molybdenite. The ore deposit is split into two ore deposits, the Main Zone, consisting of24,241,000 tonnes of mineable reserves grading 0.484 %Cu and 0.013 %Mo, and the East Zone, consisting of 66, 131,500 tonnes of mineable reserves grading 0.523 %Cu and 0.014 %Mo.The milling begins with gyratory crushing. This sizes the product down to 100% passing 6 inches. This product is discharged onto a stockpile by a stationary conveyor. The stockpile was designed for a capacity of 144,000 tonnes with a live capacity of 20,000 tonnes. Two apron feeders draw the ore from the bottom of the stockpile and discharge onto a SAG mill feed conveyor which in turn feeds a grinding circuit consisting of one 32' x 15' SAG mill and two 30' x 16.5' ball mills. The grinding cyclone overflow feeds bulk flotation at 55 -65% minus 200 mesh.The bulk flotation uses conventional rougher and column flotation methods to float a bulk concentrate recovering 92.6% copper on the East Zone and 95% copper on the Main Zone with 75% recovery molybdenum on both zones. The bulk concentrate feeds the bulk thickener which produces a density of 60 %solids. This in turn feeds the molybdenum circuit, which separates the copper and molybdenum, by depressing the copper then using conventional rougher and column flotation produces a copper concentrate of 27 %Cu and 0.02 %Mo, and a molybdenum concentrate containing 1.5 %Cu and 54 %Mo at 67% recovery. These concentrates are separately thickened, filtered, dried, and shipped to the smelter for processing."

Jan 1, 1998

By D Deb, R Pramanik

This paper presents a generalised methodology in smoothed particle hydrodynamics (SPH) framework to analyse dynamic failure process of rock mass having natural joint under blast-induced stress wave and expansion, and penetration of high pressure gaseous product. The necessary interactions of gas-rock are incorporated in the model which describes features of coupling between damage and plasticity in tension and compression respectively. A Drucker-Prager formulation of plasticity is used to model the behaviour of aggregate field and the Grady-Kipp damage model is employed for tensile strain. These two material behaviours are then brought together within the framework of interacting continua. The model relies on the Drucker-Prager plasticity surface to predict the dilatancy aspect of the material response and to account change of strength according to the strain rate effect. Three numerical examples are presented with rock joint and multiple blastholes.CITATION:Deb, D and Pramanik, R, 2015. Smoothed particle hydrodynamics modelling of blast-induced fracture processes in naturally jointed rock medium, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 65–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D. E. Hyatt

Many flotation plants practicing pyrite depression, mills leaching gold and silver ores, blast furnace facilities, and many metal plating shops share at least one common waste-water constituent of particular environmental concern-cyanide. In free or complexed form, cyanide ion is an emotionally and technically problematical reagent whose removal from water deserves attention. The initial consideration of the fundamental nature of soluble cyanides is followed by a discussion of decomposition or removal options for simple cyanide species. Complexed cyanide reactivity is discussed as it relates to ongoing or proposed methods for the decomposition or removal of soluble cyanides. New approaches to cyanide removal are discussed.

Jan 1, 1977

By Favreau RF

Over the last 20 years the blasting industry has progressed from the stage of being artform to a science as it is today. The use of computers to simulate blasting results has allowed blasting engineers to accurately pre- dict blast results and to optimise their blasting. This paper describes the computer blast simulator called BLASPA and its various applications in blasting. BLASPA allows the blasting engineer to predict blast results given known details of explosive properties, their distribution, rock type and properties, hole size, burden, spacing, collar and subdrill. The simulator runs mathematical situations and outputs numerical estimates of fragmentation and muckpile results. The paper discusses results which show that the mathematical outputs correlate very closely with actual results seen in the field, thus confirming the validity of the simulator. BLASPA can be used to help improve blast design by predicting stress levels in the rock mass and consequent rock breakage.

Jan 1, 1986