Search Documents

By J. L. Gillson

In this past year of our Institute's life, February 1960 to February 1961, we had some major problems to face, as did our members, since businesses in which they were engaged were feeling the recession. The major problems confronting us during this past year were: 1) Financing the new Engineering Center. 2) Keeping our three almost autonomous societies working together and toward a stronger AIME. 3) Cooperation with other engineering societies the Functional Plan. 4) Licensing and registration, and the Model Law. 5) The reorganization of the Council of Section Delegates. 6) Combatting the slump in the appeal of engineering to the young students.

Jan 4, 1961

By P. W. Bakarian, John C. McDonald

Three magnesium alloys were processed in various ways to exhibit a wide variation in the ratios of yield strength and tensile strength in the rolling direction compared to the cross-rolling direction. Basal-plane pole figures were prepared from several specimens. A fair correlation was observed between the property ratios and the ratio of percent of poles oriented in the cross-direction quadrants compared to the percent oriented in the rolling-direction quadrants of the pole figures. THE modes by which magnesium crystals deform are such as to lead to marked preferred orientations in all forms of wrought products. The effect of the active modes at room temperature, coupled with these orientations, is often to produce a lower compressive yield stress compared to the tensile yield stress. The phenomenon is due to easy twinning in compression, and has been well-related to the preferred orientations as described by basal-plane pole figures of the hcp magnesium single crystal. The literature contains some information on the variation with test direction of the tensile properties of sheet, but no quantitative relationship to the observed pole figures has been established. These effects have been reviewed in the few com- prehensive treatises in English which have been written on magnesium technology and metallurgy.1°3 Roberts presents several pole figures, but no tensile-property data in the plane of the sheet. Raynor has no pole figures, but quotes Frommer's4 results. The information in Beck's compendium more or less parallels the results of Jones and powell.5 In both a Mg + 1.5 Mn alloy and a Mg + 4.6 A1 alloy, cold rolling was found not to change the general situation of higher properties in the cross-rolling direction,* than in the rolling direction. Thomas'6 X-ray studies of Jones and Powell's specimens did not permit correlation of properties and preferred orientation. Ansel and Betterton7 report tensile and compressive properties on three other alloys as a function of degree of cold rolling, plus a recrystallizing anneal. As rolled, there was a change in anisotropy with degree of reduction, but all alloys were reasonably isotropic in tension when annealed. X-ray diffraction photograms illustrated the kinds of orientations present, but were not correlated with the properties. Bakarian8 has described a method of determining quantitatively a preferred orientation, and illustrated the method by applying it to pure magnesium and two of its alloys. This method was used in the present work as a basis for correlating the strength properties with the texture.

Jan 1, 1965

By R. H. Lee

So far as I am aware the references to the " kerosene blow-pipe" in the Transactions comprise only a skeptical opinion from Mr. Witherow (ix., 70), and accounts of the use of the blow-pipe by Mr. Witherbee (xiii., 675) and Mr. Gayley (xiv., 779), together with brief remarks by Mr. Weeks and Mr. Kennedy on Mr. Witherbee's paper. The subject can scarcely be considered novel, in view of these references, yet it is not so far exhausted that an additional account of the successful application of the blow-pipe would be out of place, especially if accompanied with some new details and a drawing of the apparatus itself, showing its simplicity and safety. Some time ago, owing to a variety of causes, my furnace was working very badly, the troubles culminating suddenly one morning in a chilled hearth, solid from the bottom to the tuyeres, with the exception of a narrow passage-way from above to the cindernotch, which remained open. Through this we continued to flush and cast, with the prospect of a long and troublesome siege, in working down to the iron-notch. At the end of two days matters had not greatly improved, and we seemed no nearer the desired result than on the morning of the chill, when, at the suggestion of Mr. Farrell, of Glamorgan, I decided to use the coal-oil blow-pipe; the intention being to cut a hole from the iron-notch up to the tuyeres, and then let the furnace melt out the chilled mass. In four hours from the time of starting, the hole was made and

Jan 1, 1887

By Genaro Rodríguez C.

Los residuos radioactivos son materiales que contienen varios radioisótopos que se encuentran en concentraciones de actividad (velocidad de desintegración) superior a las que son consideradas exentas por la Autoridad Nacional (OTAN). En ese sentido, el presente texto describe la gestión de los residuos radioactivos a través de los equipos radioactivos. Dichos equipos se dividen en fijos y móviles. Los primeros, son medidores de nivel, flujo de masa, composición física y química del mineral. Los segundos, determinan la humedad y densidad del suelo.

Sep 1, 2012

By R. D. Studer

"The Snow Lake massive sulphide deposits are hosted by Aphebian volcanic rocks of the Flin Flon - Snow Lake greenstone belt, which in this area were deformed and metamorphosed to the amphibolite facies during the Hudsonian orogeny. All the known deposits occur in felsic rocks a short distance below the contact with an overlying mafic rock unit.The Stall Lake copper deposit occurs close to the top of an explosive felsic volcanic sequence. Rocks stratigraphically underlying the deposit have been hydrothermally altered by the mineralizing fluids. The sulphides were probably deposited from submarine volcanic vent(s) on the flanks of a felsic dome. The ore has been tightly folded, flattened and elongated parallel to the northerly trending lineation of the surrounding rocks during the several periods of deformation. Strike lengths of the lenses range from 60 to 300 feet and plunge-to-strike ratios are as much as 15:1.Ore lenses 1 to 4 typically consist of massive coarse-grained pyrrhotite, chalcopyrite and pyrite. A stratigraphically higher lens differs in that it contains fine-grained pyrite and chalcopyrite, with an increase in sphalerite toward its hanging wall. The No.4 orebody has a distinct footwall alteration zone characterized by brecciation and abundant chlorite-staurolite-garnet schist, with minor kyanite, anthophyllite, cordieriteand anhydrite, as well as sulphide minerals. Chemically, the alteration zone is distinguished from the unaltered felsic rocks by Na20 depletion and Mg-Fe enrichment.IntroductionThe Stall Lake copper deposit is located aproximately 4 miles southeast of Snow Lake in northern Manitoba (Fig. 1). The Snow Lake district has been a producer of gold (Rex, Bingo, Laguana and Nor-Acme Mines) and, since the fifties, of copper and zinc from deposits of Hudson Bay Mining & Smelting Co., Ltd . The district is located near the eastern limit of the Flin Flon - Snow Lake greenstone belt, which contains Amisk metavolcanic rocks of Aphebian age."

Jan 1, 1982

By Abel Aragón Espinoza

"El objeto del siguiente trabajo es describir los procesos implementados en la Planta de Cianuración del Sindicato Minero de Parcoy, S.A., situada en el campamento minero de Retamas, distrito de Parcoy, provincia de Pataz, La Libertad. La planta trata minerales piritososo con un contenido en oro que varía desde 6.5gr./tm. hasta 13 gr/tm., asi como los provenientes de otros minas como: Carlos Bernabé, Mishencanto, Cabana, Loros, Alaska. También desarrolla procesos como la trituración, donde el material triturado es depositado en una tolva metálica (120 T.M) para ser alimentado posteriormente por una molienda. Dicha máquina de molienda intermedia (New House de 5 Style B) sigue alimentando a través de una faja, para luego pasar a un molienda fina de 7 ' de diámetro por 10' de longitud, con alimentador de cuchara. Luego procede el tratamiento de las lamas, la precipitación y la fundición, donde el mineral es fundido en un horno de crisol abundante durante dos horas. Posteriormente la refinación comprende dos etapas: la refinación electrolítica en la que los ánodos son las planchas de grafito y los cátodos son planchas de grafito, convirtiendo al electrolito en una solución de ácido nítrico, con cobre y plata.y química, mientas que en la refinación química, el producto adquirido es cargado a los frascos Herlemmeyer y es atacado con una solución de una parte de ácido nítrico con dos de agua y una pequeña cantidad de alcohol. Como resultado final de este proceso, se considera al oro recuperado en un 92%."

Jul 20, 1956

By S. K. Nowak

The lithium solubility limit in solid aluminum was determined by the use of micro-graphic techniques. The solubility limit thus established was shown to be a true equilibrium by checking the reversibility of AlLi phase precipitation and dissolution around the equilibrium temperature. The experimental results fit a straight line by plotting log N(LI) against 1/T. The metallurgical reasons explaining the lack of agreement among previous investigations are discussed. THE solubility limit of lithium in solid aluminum was determined by Shamray and Saldau1 by micrography and by Grube et al.' and also Voss-Kiihler- by measurement of electrical resistivity. Since the addition of lithium induces extremely small changes in the aluminum lattice, X-ray techniques could not be employed for this purpose; in fact, the addition of lithium does not cause an expansion of the lattice as might be expected from a consideration of atomic radii, but causes a small contraction from 4.040 to 4.037A3, 4 when the solvent aluminum is saturated with this element. An analysis of the results from previous investiga-tions'" shows that with improvement of investigation techniques the solubility limit tends toward a lower lithium content. Again, some of the author's own experimental results on the action of atomic hydrogen on A1-Li alloys seemed to indicate that the solubility of lithium should be much lower, i.e., about 0.3 pet at 300°C: instead of 1.15 pet, the lowest published value.4 For the foregoing reasons it was decided to investigate this problem. The aluminum and the lithium used for this purpose were of the highest purity. The lithium solubility limit was determined by metallographic techniques, in particular by the use of a reagent especially developed for the purpose of revealing the AlLi phase. The solubility limit thus determined was shown to be a true equilibrium by checking the reversibility of AlLi phase dissolution and precipitation around the equilibrium temperature. All of the experimental work was carried out in 1951 at the Centre d'Etudes de Chimie Metallur-gique at Vitry, France, under the direction of Georges Chaudron.

Jan 1, 1957

By R. Fred Pena

The Tower Mill has proven to be a grinding machine with a demonstrated application flexibility. Variations in applications have proven to be numerous. This mill was originally intended for fine grinding applications. Subsequent testwork and installations have demonstrated the mill can be utilized in place of ball mills as secondary mills. The following lists a few of the circuits tested: 1. Tower Mill secondary receiving feed from a primary SAG mill grinding stage. 2. Tower Mill as tertiary grind unit following a rod mill/ball mill. 3. Tower Mill as secondary grind unit following a primary ball mill. 4. Tower Mill as a limeslaker. 5. Tower Mill grinding as a primary unit taking limestone crusher discharge. Applications demonstrate the mill is energy efficient and is sensitive to the following consideration: 1. Circuit chosen. 2. Top size of feed. 3. Product size required. 4. Classification equipment performance. 5. Media size required. 6. Media type required.

Jan 1, 1986

Very little has been written about the discovery and early history of prospecting of ironstone deposits in the Iron Knob-Middleback Range area of South Australia, the main source of supply of ironstone (hematite) for the Australian steel industry, and scanty though the record is, much of it is wrong or misleading.With the help of several people, to whom acknowledgement is made at the end of the paper, the writer has unravelled some of the story, but not the whole story. It is hoped that publication of this paper will stimulate interest in others, who may be able to supplement this account from family records, from the files of newspapers, or from archives.

Jan 1, 1969

By M. S. Klima, P. T. Luckie

Proper analysis of washabiity data can lead to the development of a maximum yield coal preparation plant flow sheet. Simulations, as simple as spreadsheet mass and water balancing, are important in examining yield maximization and middlings liberation. Key to such attribute tracking flow sheet simulations is the distribution model, expressing the probability of a species reporting to the product stream. There are many such models in the literature. This paper examines a functional form that can represent or fit most of the proposed distribution functions.

Feb 24, 1997

By J. R. Wait, D. A. Hill

The feasibility of locating a buried vertical magnetic dipole source (horizontal loop) from surface measurements of the vertical and horizontal magnetic field components has been investigated by Wait (1971). , For sufficiently low frequencies, the magnetic fields have a simple static-like behavior, and a single observation of the ratio and relative phases of the vertical and horizontal field components is sufficient for location when the earth is homogeneous. However, when inhomogenieties are present, the surface fields will be modified, and source location may be more difficult. In order to obtain a quantitative idea of the surface field modifications, we consider a spherical conducting zone as a perturbation to the homo- geneous half-space. A rigorous solution for the buried sphere problem has been formulated by D'Yakanov (1959). Unfortunately, his solution is restricted to azimuthally symmetric excitation, and even then the solution is not in a convenient computational form. However, if the sphere is electrically small and is located at a sufficient distance from both the dipole source and the interface, the scattered fields can be identified as the secondary fields of induced dipole moments. The latter are equal to the product of the incident fields and the polarizabilities of the sphere. The details of the approach are given by Hill and Wait (1973). Wait (1968) has used this induced dipole moment approach for scattering by a small sphere above a conducting half-space. The method has the advantage that it is easily generalized to scatterers of other shapes for which both the electric and magnetic polarizabilities are known, such as spheroids (Van de Hulst, 1957). This concept has

Jan 1, 1973

By Israel Huapaya, Juan Crisostomo, Dalia Valladolid

En el presente documento se describe la metodología utilizada para optimizar los procesos de extracción de muestras de roca sólida mineralizada con contenidos de oro correspondientes a un conjunto de vetas en interior mina, incluyendo la optimización del muestreo de fragmentos de roca mineralizada descargada en canchas

Sep 30, 2022

By C. Palacios

The Plant, which was started up in April 1970, was originally designed for a capacity of 40.000 ton of cathodes per annum, using 12 sections, containing 408 cells. Since then the addition of another 8 sections containing 280 cells and using the Reverse Current System has made possible the increased output of 109.000 ton. The quality of the cathodes produced is excellent. The extension of the Electrolytic Refinery, by the introduction of the Reverse Current System, has been a great success and no problem has arisen in the new equipment or in the modifications carried out in the plant. The operation of the plant has improved due to better control procedures.

Jan 1, 1976

By B. N. Whittaker, C. J. Bonsall

The paper gives an account of the factors influencing the stability of coal mining tunnels and goes on to examine various bases of support and lining design of such tunnels in relation to geological and mining conditions. The different types of coal mining tunnels are compared and comments made regarding the factors influencing their choice and basic design features. Foremost amongst design considerations is the design method and special thought has been given to the validity of different formulae as related particularly to UK Carboniferous geological conditions. Emphasis is placed on the role of the stress field in relation to tunnel stability. Shape of mining tunnel has been investigated and conclusions drawn regarding the merits of different commonly excavated geometries from a stability point of view. Detailed design aspects pertaining to determination of tunnel lining strength and resulting stability are critically examined and current design methods are compared. Data from UK mining tunnels are included as the basis for comparison of these design methods.

Jan 1, 1983

By R. S. Archibald

THE Blueberry mine is about 10 miles west of Ishpeming, Marquette County, Michigan. The property consists of about 2000 acres in sets. 3, 4 and 5, T. 47, N.R. 28W. and sets. 32, 33 and 34, T. 48, N.R. 28W., and, excepting one intervening 80-acre tract, contains the iron formation for a length of about 2 1/4 miles. The property is traversed by State Highway M-28 and is served by three railways, the Chicago & Northwestern, the Duluth, South Shore & Atlantic, and the Lake Superior & Ishpeming. The Northwestern transports the ore to a dock at Escanaba; the other railways, to Mar¬quette. Ore for Chicago goes via Escanaba and that for Lower Lake ports, as Detroit, Cleveland, and Buffalo, via Marquette.

Jan 1, 1935

By Sidney Powers

Discussion of the paper of SIDNEY POWERS and ALFRED C. LANE, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 535 to 548. N. L. BOWEN, Washington, D. C. (communication to the Secretary*). -This detailed study and. complete demonstration of differentiation as a result of the sinking of crystals has a great general significance in petrogenesis. If this action can be demonstrated in an effusive body, even though a very thick one, how can one doubt its possibility in large intrusive bodies? The authors speak of the sinking of augite and the rising of plagioclase but I should consider that they should depend entirely on the former action to obtain their results. It is true that in my experiments, to which the authors refer, a floating of crystals was in one case obtained, viz., in the case of tridymite crystals, but it must be remembered that tridymite has an exceptionally low density. Plagioclase crystals, on the other hand, are of nearly the same density as basaltic liquid. Under magmatic conditions they might be a little heavier than the liquid or a little lighter, we do not know which, but the margin would be exceedingly small and any motion resulting, whether upward or downward, would be correspondingly small in the usual case. For this reason I should think that the sinking of pyroxene should be considered probably the sole factor in producing the observed result, for which purpose it appears to be entirely adequate. The measurements of grain have also a certain significance in this connection. In the experiments referred to a difference of grain was obtained in different parts of the charge, which was entirely independent of the rate of cooling but connected with the fact that a sinking crystal does not depend entirely upon diffusion for the collection of its material from the surrounding liquid. The crystals which sank a considerable distance were therefore exceptionally large. Now in the Cape Spencer flow the augite crystals are normally (top and bottom) somewhat smaller than the plagioclase crystals, but in the layer somewhat below the middle,

Jan 5, 1916

By S B. Martin, M P. Simpson, J L. Mauk

The Martha deposit in Waihi, New Zealand, is a giant adularia-sericite epithermal gold-silver deposit that formed 6.0 to 6.1 Ma, and has produced over 6.4 Moz gold and 39.9 Moz. Fluid inclusion analyses were undertaken on a limited number of vein samples from Martha. The results from this eight week student project are preliminary but agree with previous studies. There is little variation between primary and secondary inclusions and between different vein types, except that homogenisation temperatures of the inclusions in sphalerite grains are on average 20¦ to 30¦C higher than the average quartz vein values. Overall the temperatures of homogenisation ranged from 182¦ to 258¦C and final ice melting temperatures ranged from 0.0¦ to 2.8¦C. Unusual black inclusions were also found associated only with the ginguro bands. Some of these appear to be solid sulphide inclusions but others are not so clear.

Jan 1, 2007

By V. I. Lakshmanan

Process Research ORTECH Inc. (PRO), with its in-depth knowledge on cobalt behaviour in nickel matte smelters and its novel mixed chloride hydrometallurgical processing, is developing a hybrid process to enhance cobalt recovery. PRO’s experimental data is compared with plant information on cobalt behaviour in smelters. In final stages of iron rejection in the converters, the thermodynamics of the matte-slag system dictates the undesirable transfer of the cobalt to the final converter slags. This results in much lower cobalt recovery in the product Copper/Nickel matte (<60%) in present copper and nickel smelters. This information is used to transfer cobalt into desired quantity of converter slag. The enriched cobalt slag is subjected to PRO mixed chloride process to recover nickel, and cobalt as high value salts of importance in lithium ion batteries. From a typical converter slag containing 3.5% Ni, 1.5% Co, and 1.0% Cu, PRO leach process extracts 98 % Ni, and 98 % Co, and 99% Cu. Application of this process to enhance cobalt recovery in typical Copper/Nickel smelters is presented. In addition, this will also enhance the Copper and Nickel recovery. Both these aspects are of interest to the Copper, Nickel, and cobalt producers. INTRODUCTION In pyrometallurgical extraction of copper and nickel from sulphide ores cobalt often occurs with copper and nickel. The requirement of cobalt is increasing due to its need in lithium ion cells used in electric vehicles. Therefore its efficient and economical extraction in a form suitable for use in lithium batteries is of great interest at present. In the pyrometallurgical processing of copper and nickel sulphide concentrates the concentrate is smelted to produce a furnace matte, which is then sent for converting to remove the iron to produce iron free (~1% Fe) matte for further processing to copper or nickel matte. The copper/nickel matte is processed for metals recovery by hydrometallurgical or vapo-metallurgical or oxidation – reduction routes to make market products. As shown in Figures 1 and 2 the slags are produced in the smelting step and in the converting steps. The metal losses in smelting are controlled by the oxygen pressure in that step and slag production which is controlled by concentrate grade. The slag produced in the converting step which is carried out at a higher oxygen pressure contains higher level of metals is often returned to the smelting step to increase value metals recovery.

Jan 1, 2019

By Zamel G. I, Zenari L. P

Technological developments in modem Tunnel Boring Machines (TBMs) and associated back-up equipment are offering significant alternatives for mining operators to consider, in the selection of equipment for coal mine development drifts, roadways, longwall gate roads as well as metalliferous mining declines and development drives.Greater flexibility in handling variable ground conditions, muck disposal and radius of turn as well as advance rates, are just some of the areas where modem TBMs can accomplish the flexibility that mine operators require to achieve cost-effective developments.Compact TBMs are achieving this acceptance because of the fundamental design of a shielded machine containing electrics and hydraulics within the forward shell, ability to achieve tight radius of curvature and grades, and ability to provide highly flexible support systems to meet all possible ground conditions.However, a single TBM design will not suit all mine developments, as each development method - while having common goals with all mine developments - will also require certain unique criteria to be fulfilled.

Jan 1, 1993

By C. D. Anderson

"IntroductionTungsten carbide is a valuable material used in a variety of different applications, including the manufacturing of cutting tools, bearings and as a cost-efficient alternative to industrial diamonds. Both the high hardness value (Mohs 9) and scratch resistance of this material make it a valuable commodity for use in the mining industry.Usually, the production of tungsten carbide is a multistep process involving one or more of the following unit operations: hydrometallurgical digestion, solution purification, crystallization (as ammonium paratungstate), calcination, hydrogen reduction and carbon synthesis. The proposed three-step process eliminates three of these steps (crystallization, calcination and hydrogen reduction) by implementing a combination of hydro/pyrometallurgical techniques. These include alkaline pressure leaching, carbon adsorption and carburization roasting. By eliminating some of the intermediate processing steps, there is potential to reduce energy consumption and decrease overall operating costs.Methods and resultsInitially, alkaline pressure leaching with sodium carbonate (Na2CO3) was employed to selectively leach tungsten, as tungstate (WO4 2-), from an industrial Scheelite (CaWO4) flotation concentrate. Experimental variables included lixiviant (Na2CO3) concentration, temperature and residence time. Experimental constants, based on previous work, were percent solids at 13 wt% and agitation at 400 rpm (Queneau and Strathmore, 1969). Leaching results showed it was possible to extract 97% of the tungsten present. The most favorable conditions for leaching were determined: 2M Na2CO3, temperature of 180° C and a residence time of 30 minutes."

Jan 1, 2015