Search Documents

By Alvin W. Schillinger

Drilling was not entirely satisfactory in the search for native copper in the Osceola amygdaloid footwall as mining showed oreshoots to be more continuous than drilling indicated. The Geophysics Department of Michigan Technological University developed a portable induced polarization drill hole probe with a 3 electrode configuration and a sampling radius of 5'± A 20 ma current of alternately reversed polarity is pulsed at 3.5 sec. intervals and readings are taken every two feet. Potential is read during the "on" cycle for resistivity determinations. During the "off" cycle, after 10 ms delay, the I.P. potential is sampled for 10 ms and recorded. Resistivity (ohm-feet) and "S" values (mv/v) are plotted on semi-log paper. A lithologic log is plotted based on resistivity and anomalous "S" values noted. The low resistivity amygdaloid contains sills of high resistivity basaltic trap. Verified by core logs, amygdaloid-trap contacts could be picked to ±.5' from resistivity alone. Lithologic logs of long steel holes, based' on resistivity, now replaced sludge logging. An "S" value of 30 mv/v was established as the lower limit of diagnostic I.P. effects in mineralized amygdaloid and 50 mv/v as a threshold value for ore. Of 914 footwall zones drilled, 315 were probed yielding 203 anomalies. Success increased from 34% for drilling to 72% for drilling and probing. As checked by mining, 46 probe results were 78% correct. Failures were due to the instrument not detecting copper or to the misinterpretation of an anomaly. No false anomalies were found.

Jan 1, 1964

By S. R. Bryan, J. D. Stephens, D. R. Rothbard

The distributions of gold and associated elements in mineral grains from a pyritic gold ore were studied by optical microscopy, and by SEM and SIMS imagery. Products studied were a sulfide flotation concentrate, a calcined sulfide concentrate, a cyanide leached calcine, and a cyanide leached pressure oxidation residue. Individual pyrite grains are compositionally zoned and solid solution gold occurs in some, but not all zones. Most of the gold in calcined products is present as metallic coalesced grains that are smaller than 100 angstroms. Gold lost into cyanide leached residues from the calcines tends to be in “semi-dense” grains that cannot be distinguished from gold-free grains except by SIMS analysis. The gold in cyanide leached pressure oxidation residues occurs as solid solution gold in unoxidized pyrite remnants.

Jan 1, 1990

By Theodore B. Comstock

Prior to 1885, the College of Engineering in the State University was under the care of such professors and instructors as were required for efficient work in the Schools of Mechanical Engineering, Civil Engineering and Architecture. The development of the coal and other important mineral resources of the commonwealth led gradually to a considerable demand for instruction in the branches more closely related to mining engineering, and a very creditable effort was made to meet this want by arranging special work in the field and in the laboratory for students of mining and metallurgy. This plan, while it gave much added labor to several already heavily taxed professors, caused such students to become something like undesirable excrescences upon the regular courses. But its partial success gave abundant proof of the real necessity for a complete course in Mining Engineering. The famous Braidwood disaster emphasized anew the importance of thorough training on the part of those to whom the responsible duties of mining must be confided. As is well known, a very excellent beginning was made some years ago by the Legislature in the matters of inspection and regulation by the enactment of a reasonably effective law, which was afterward much improved.* About the date of the last Acts, it was deemed wise to enlarge the facilities at the University arid to furnish adequate training for the increasing number of applicants. Accordingly, in August, 1885, the writer was requested to assume the duties of the professorship, it being the expressed desire of the Board of Trustees and the Regent of the University that a School of Mining Engineering should be founded which might eventually come to rank with the other engineering schools already flourishing here. It is the main object of this paper to state plainly the steps thus

Jan 1, 1887

By Anderson KG

Multi-seam mining under the western portion of Lake Macquarie NSW commenced in 1982. Up to three seams separated by partings ranging from 10 to 30 metres are mined simultaneously by Newcom Collieries. A feature of these workings is the minimal bedrock cover, which ranges from 130 metres down to only 40 metres. "Surface" subsidence control has an over-riding influence on the design of the workings. Subsidence considerations govern both the selection of the mining method and the dimensioning of the workings. To date, workings have been designed in accordance with the "Wardell Guidelines for Mining Under Tidal Waters". These guidelines are tabulated and evaluated in the light of advances in rock mechanics knowledge and local subsidence data collected since the Guidelines were formulated in 1974. The local and regional stability of shallow workings designed according to the Guidelines is evaluated.

Jan 1, 1986

By J. R. Morris, A. E. Ball, G. W. Kuzyk

"AECL Research has constructed an underground laboratory for the research and development required for the Canadian Nuclear Fuel Waste Management Program. The experimental program in the laboratory will contribute to the assessment of the feasibility and safety of nuclear fuel waste disposal deep in stable plutonic rock.In 1988, AECL extended the shaft of the Underground Research Laboratory (URL) from the existing 255 m depth to a depth of 443 m in cooperation with the United States Department of Energy (USDOE). The project, which involved carrying out research activities while excavation and construction work was in progress, required careful planning. To accommodate the research programs, full-face blasting with a burn cut was used to advance the shaft. Existing facilities at the URL had to be modified to accommodate an expanded underground facility at a new depth. This paper discusses the design criteria, shaft-sinking methods and approaches used to accommodate the research work during this shaft extension project.IntroductionThe Underground Research Laboratory (URL), a major geotechnical research facility, has been developed by AECL Research, 120 km northeast of Winnipeg, Manitoba. The URL is part of the Canadian Nuclear Fuel Waste Management Program (CNFWMP), which is assessing the concept of nuclear fuel waste disposal in a vault deep in stable plutonic rock of the Canadian Shield (Hancox, 1986). The URL provides a representative environment to conduct a wide variety of geotechnical research relevant to nuclear waste disposal. Extensive characterization and monitoring programs were carried out prior to construction and will continue during operation. The operating phase experiments began in 1989 and will continue until the year 2CXXl (Simmons, 1990). Figure I shows the present extent of the URL facilities and the proposed future development."

Jan 1, 1991

By C. E. Wood

THIS paper is a brief report of experimental work undertaken to determine whether barium oxide in any quantity increases the desulfurizing action of blast-furnace slags. Industrial furnace operation with slag containing small quantities of barium oxide, referred to later, interested S. A. Sanford of the Commercial Chemical Co., Youngstown, Ohio, to conduct experiments to furnish comparative results on desulfurization with normal slag and slag containing small quantities of barium oxide. The U. S. Bureau of Mines agreed to assist on the problem because of the possible saving in fuel if the desulfurizing action of blast-furnace slag can be substantially increased, also because the experiments would yield new information on sulfur elimination in general, a matter of economic importance in furnace practice. A more complete and fundamental study of desulfurization of iron by slag is in progress.

Jan 1, 1929

By Carle Hayward

THIS work was first undertaken in the metallurgical laboratory of the Massachusetts Institute of Technology in 1907 by L. A. Dickinson, E. Phelps, and V. S. Rood, under the author's direction. They attempted to determine the diagram for the system Cu2S-NiS, but several inexplicable results were obtained. The following year, P. H. Mayer with Mr. Dickinson carried, on some experiments with nickel sulphide and found that the molten material slowly lost sulphur until it reached a composition corresponding to the compound Ni3S2, established by Bornemann.1 At this point the composition remained stable. The freezing points of the mixtures gradually fell off with the loss of sulphur. Since the above facts seemed to explain the erratic results obtained in the first experiments, Mr. Mayer with F. Jaeger attempted in 1910 to establish a correct equilibrium diagram for the Cu2S-Ni3S2 series. They prepared pure Cu2S and Ni3S2 and determined the cooling curves for various mixtures. The fusions were made in a platinum resistance furnace and the temperatures were measured with a platinum-iridium thermocouple connected with a Sullivan galvanometer. The curve was established for mixtures containing more than 40 per cent. Cu2S, but they were unable to determine certainly the direction of the curve beyond that point. Nothing further was attempted with this series until the present year, when the work was carried to a successful conclusion with the assistance of A. Butts, Jr., and E. H. Weil. The results of this work are given in the following pages.

Jan 1, 1914

Report of the Secretary TO THE BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen:-To a Board of Directors keeping in as close touch with all of the affairs under their care as do the Board of Directors of the A. I. M. E., through their monthly meetings, a report of the year's progress is almost superfluous. To the members who read the monthly reports of. the Board Meetings and of the various activities of the Institute as published each month, a yearly report cannot carry much fresh information; yet for both it may be well, as is the custom, to glance over the field of our activities during the past year, and to make an estimate for the year to come. The beginning of 1924 was not propitious for the members of the mining profession, though tonnage production for 1923 had been high and the gross value higher than for several years. The margin of profit had been narrow, prospecting and development were limited, and many of our members were unemployed, or were working in other industries. Toward the end of the year, higher metal, prices were in sight. Old-time optimism began to grow, and it now brightens the outlook for 1925. An excellent barometer of the prosperity of the industry, and that of the Institute, for they go hand in hand, is the work of our Employment Bureau. During the past few months, the percentage of our members for whom openings have been found has been increasing to a marked extent, and many members who had fallen in arrears are placing themselves in good standing. The number of new members joining has remained about as it was in 1922 and 1923. The Directors have reason to congratulate themselves on the interest maintained during a dull period, for it is not humanly possible to take a keen interest in the technology of an industry when our hands and minds are not actively engaged in it Now, with a much brighter outlook, we can look forward to a year of increasing prosperity for the industry and for the Institute.

Jan 3, 1925

By W. E. Robinson

Differences in the composition or chemical structure of the organic material in samples of Uinta Basin (Utah) oil shale were studied relative to stratigraphic position within the Green River Formation. This involved a systematic study of the soluble organic material and the insoluble organic material (kerogen) present in the samples. Emphasis was placed upon the distribution of the alkanes (normal and isoprenoid compounds) in the soluble extracts and upon the aromaticity of the kerogen. Significant differences exist in the chemical composition of the organic material from various strata within the Uinta Basin, some of which were related to burial depth but most were related to source material variations, environmental differences, or other factors. The Uinta Basin samples differed significantly from Piceance Creek Basin and Green River Basin samples in the large amount of soluble extract they contained.

Jan 1, 1975

By D. S. van Vuuren

Industrial production of titanium occurs via the batch-wise reduction of titanium tetrachloride (TiCl4) with a reducing metal, being magnesium in the Kroll process, or sodium in the Hunter process. In the search for low cost titanium, the CSIR is developing a continuous process to produce titanium powder directly via metallothermic reduction of TiCl4 in molten salt, dubbed the CSIR-Ti process. The move to a continuous process has been attempted by a number of organizations, but was until now always met with failure, due in no small part to challenges inherent in the process chemistry. The reaction between TiCl4 and the reducing metal can occur directly, when TiCl4 or any titanium sub-chlorides present, comes into contact with suspended or dissolved reducing metal. The reaction can also occur indirectly, without any physical contact between the reacting species, via an electronically mediated mechanism. The reaction mechanism via electronic mediation can cause TiCl4 to react at the outlet of the feed port, rapidly causing blockages of the TiCl4 feed line. The electrical conductivity of the metal reactor can also cause the electronically mediated reaction to favour the formation of titanium sponge on the reactor walls and internals, rather than titanium powder. Various methods were investigated to overcome the problem of blockages in the TiCl4 feed line, e.g. mechanical removal, sonic velocities, dilution of the TiCl4 and the use of ceramic feed lines. This article discusses problems experienced with the continuous feeding of reagents, and various methods attempted are shown and discussed. Information is also given on the morphology, chemical composition and suitability of the final titanium powder for powder metallurgical application as presently produced by the CSIR-Ti process. Keywords Titanium dioxide, titanium nitride, carbo-thermic reduction, ilmenite, slag, tunnel kiln, residence time.

Jan 1, 2011

By E. A. Almond

An attempt is made to explain the effect of stress on strain aging by examining the mechanism of yielding for a group of aged dislocations. The experimental results on which the theory is based indicate that a linear relationship develops between the aging stress and the discontinuous yield effect in a low carbon steel THE discontinuous yield effect that occurs in bcc metals after strain aging is usually explained by the interaction of interstitial atoms with individual dislocations. Attempts have been made to interpret the kinetics of strain aging in terms of interstitial segregation to nonrandom groups of dislocations1-3 but apart from Li's4 work little or no effort has been made to examine the effect of groups of aged dislocations on mechanical properties. It appears likely that such groups can be stabilized if a positive load is maintained on the specimen during aging5 and, furthermore, that the enhanced strain aging effect associated with aging under load might be due to the stability of these aged groups. The effects associated with this latter phenomenon have been described by Almond and Hull, Ref. 5, Figs. 2 and 3, and it is found that the upper yield stress, the lower yield stress, and the yield point elongation are increased by aging under load. The yield point elongation reaches a maximum value but the enhanced effect persists in the upper and lower yield stress values even after extended aging treatments when the general level of the flow stress curve rises. The flow stress, as measured at 8.5 pct total strain, however, is independent of aging stress. Almond and Hull5 showed that it was unlikely that the differences in mechanical properties could be caused by stress enhanced diffusion and they suggested that the effect was in some way associated with the different dislocation distributions that are obtained when specimens are aged with and without an applied stress. At that time no explanation was offered for the strengthening effect produced by stabilized dislocation distributions but additional tests have been performed to establish a quantitative relationship between aging stress and mechanical properties, and also to examine more closely the effect of varying the procedure for applying the aging stress. EXPERIMENTAL The material used was an iron wire containing 0.015 wt pct C, 0.002 wt pct N, and 0.006 wt pct 0. Tensile specimens with a 1 cm gage length and 0.08 cm diam were annealed at 850°C for 1 hr in vacuum to establish a grain diameter of 0.032 mm and then aged at 200°C for 24 hr. After this treatment the amount of carbon left in solution would be less than 10-4 wt pct, and ni- as aging time is increased. It is suggested that this observation, and effects that arise from varying the method of applying the aging stress, can be explained by a strengthening mechanism whereby dislocations are more difficult to move when they are aged in piled-up groups. trogen would be the main cause of strain aging. Tensile tests were performed in a hard beam machine at a constant crosshead speed of 0.02 cm per min and the specimen chamber was immersed in a temperature controlled silicone oil bath at 32" * 0.05"C. RESULTS All specimens were prestrained 5 pct before aging under stress and the results in Figs. 1 to 5 show the effect of aging time and aging stress on the following parameters ?UY = auy — ?F(5); i.e., the difference between the upper yield stress after aging,?uy, and the flow stress after prestraining 5 pct, ?f(5). ?LY = sly —sf(5); the difference between the lower yield stress after aging, ojy, and the flow stress after prestraining 5 pct. s8.5 = the flow stress at 8.5 pct total strain after aging at 5 pct strain. Varying the Loading Procedure. Three variations in the procedure for applying the aging stress were examined; i) After prestraining, the specimen was unloaded to a stress of 18 kg mm-2, aged at that stress, and then tested. ii) After prestraining, the specimen was unloaded to 2 kg mm-" then reloaded to 18 kg mm-', aged at that stress, and tested. iii) After prestraining, the specimen was unloaded to 18 kg mm-', aged at that stress, then unloaded to 2 kg mm- before testing. Specimens were unloaded or reloaded by decoupling a clutch in the drive transmission of the tensile machine. This enabled the crosshead to be driven manu-

Jan 1, 1970

By Sheldon Rideout, E. L. Kamen, B. S. Lement, Paul A. Beck, W. D. Manly

The 1200°C isothermal sections of the following ternary phase diagrams were investigated: Cr-Co-Nil Cr-Co-Fe, Cr-Co-Mot and Cr-Ni-Mo. In all these systems the u phase was found to form extended solid solutions. Two new ternary phases of unknown structure were identified. The existence range of intermediate phases of transition elements was correlated with 3d electron vacancy concentrations. THE occurrence of extensive ternary d solid solutions in the Cr-Co-Ni and in the Cr-Co-Fe systems was described in a brief note.' More recently d- solid solutions were also found in the Cr-Fe-Mo system by two independent groups of investigators.2,3 The existence of binary d phases in the V-Co and V-Ni systems, predicted in ref. 1, was experimentally discovered recently by Duwez and Baen and independently by W. B. Pearson, J. W. Christian, and W. Hume-Rothery.5 Duwez and Baen stated two general conditions for the occurrence of the d phase in alloys of the transition elements: "(1) The atomic diameters of the two metals do not differ by more than 8 per cent. (2) One of the two metals has a body-centered cubic structure while the other is face-centered cubic, at least in one of its allotropic forms." In the course of an extensive research program conducted at this Laboratory under the sponsorship of the NACA, several ternary systems, containing d solid solutions and also certain new ternary phases, were investigated. The present report describes the investigated portions of the 1200°C isothermal sections of the following ternary phase diagrams: Cr- Co-Ni, Cr-Co-Fe, Cr-Co-Mo, and Cr-Ni-Mo. It was found that the range of existence of the d phase in these four ternary systems, as well as in one of two ternary systems which were investigated by others, can be fairly consistently described in terms of electron vacancy concentrations. This supports the suggestion of Sully and Heal" that the d phase is an electron compound. Experimental Procedure The ternary alloys were prepared by vacuum induction melting in zirconia and alumina crucibles. Lot analyses of the metals used are given in Table I. Specimens of all alloys were annealed at 1200°C in an atmosphere of purified 92 pct helium and 8 pct hydrogen mixture. Alloys consisting mainly of

Jan 1, 1952

By Walid El Kamash, Sadik Oztoprak

"Soft soil presents a challenge against multistory buildings in some cities of Egypt such as Port Said due to the consolidation settlement. Deep mixed (DM) columns are used to improve the soft foundation soil in order to reduce the total and differential settlements. Latest research revealed that this improvement technique also increases the rate of mechanical consolidation due to column yielding caused by stress concentration from the soft soil. In this study, extended poly-styrene (EPS) Geofoam is used to replace the soft soil over DM columns in order to control the stress concentration and settlement. To understand the effect of EPS geofoam on the degree of consolidation, stress concentration and settlement, a parametric study was carried out through a mechanically and hydraulically-coupled numerical method. A unit cell model is used, in which the soil was considered linear elastic; DM column and EPS Geofoam are elasticplastic materials. Results reveal that EPS geofoam is helpful for reducing the settlements and accelerating the consolidation. Increasing the length of the column of the deep mixed foundation with EPS geofoam has a significant effect on accelerating the consolidation.INTRODUCTIONExpanded polystyrene (EPS) geofoam is a lightweight polymeric material which is made by expansion of raw plastic beads. The expansion of the EPS beads are spherical-shaped particles containing closed hollow cells. EPS which plays an important role as an innovative lightweight construction material is now well recognized due to its low density in addition to high compressive and rupture strength. Inglis (1996) reported the first use of EPS geofoam as a seismic buffer to reduce potential seismic loads against a nonyielding basement wall. Gaskin (2000) and Bathurst et al. (2007) carried out reduced-scale shaking table test on a rigid retaining wall protected by EPS geofoam. The test data showed that the peak lateral loads acting on compressible model walls were reduced below values measured for nominally identical structure but with no compressible inclusion. Abdelrahman and El Kamash (2014) investigated the behavior of EPS Geofoam beneath raft foundation on soft soil of Port Said. They showed the ability of EPS to control vertical displacements. The investigation of the behavior of EPS geofoam with DM column has not attracted more attention of previous researchers. In this paper, the behavior of replacing the soft soil by EPS geofoam was examined in the presence of DM column."

Jan 1, 2015

By R. E. Somers

1. INTRODUCTION 1. Location, Topography, and Climate The Burro Mountains are located in the southwestern part of New Mexico, in Grant County. The group is made up of two distinct moun-tain masses, known as the Little Burros and the Big Burros, the former lying about 6 miles southwest of Silver City-, and the latter about 9 miles farther in the same direction. They are separated by the valley of the Mangas River, a tributary of the Gila, and a stream only in name, except after a heavy down-pour of rain. . The Little Burros attain an elevation of 6,625 ft. above sea level, and the Big Burros 8,054 ft., with the surrounding country averaging about 6,000 ft. To the south of these mountains stretches the desert plain, while to the north are the more frequent elevations of the mountainous country.

Jan 5, 1915

By W E. Short

Ausmelt top submerged lance technology is at the cutting edge of technological developments in non-ferrous metal smelting with commercial operations throughout the world. The Technology is being used for lead smelting, copper smelting and matte converting, fuming zinc from slags, recycling iron residue from zinc plants, processing the aluminium industry hazardous waste SPL , precious metal processing, nickel-copper residue smelting and converting, and tin smelting. The Technology is also being developed for projects involving iron-making and waste industry opportunities. There are 19 furnaces operable or under design at the time of writing. The benefits to operators using Ausmelt Technology vary depending on application, but typically result from environmental improvements, enhanced recovery of valuable products, lower capital and operating costs, more flexible operations capable of handling a wide range of feed materials, better removal of impurities, or improved product quality. Growing industry acceptance of the Technology is evidenced by the fact that more than 20 per cent of the worldÆs tin production will be extracted in systems using Ausmelt Technology when the Yunnan Tin Corporation plant starts up in 2001. Metallurgists, industrialists and investors have accepted the Technology for improved operations in both greenfield main smelters and add-on plants in Korea, China, Japan, Germany, Peru, Zimbabwe, India, Namibia and Australia. Ausmelt intends that this paper will update the industry by outlining recent achievements of the Technology in global metallurgical operations.

Jan 1, 2000

By W. Edeburn, H. R. Fife

An extended study of dustproofing Freeport-seam coal has emphasized several fundamental features in the successful treating of bituminous coals. The extent of the exposed surface area and its absorption propcrties for the dust-retaining film were found to be the most critical factors affecting the efficiency of fly-dust prevention. From recently published screen data and specific surface-area measurements on United Kingdom coals, an approximation of the surface exposed by mine-run coal and by 1-in. slack was made. The total surface area exposed by an average tori of this mine-run coal was estimated at 3768 sq. yd., while a ton of 1-in. slack represents a total surface area of 8779 sq. yd. with no additions for porosity. It is important in coal treating to consider that in mine-run coal the fraction above 1/4 in. in size represents 79.5 per cent of the total weight, but only 4 per cent of the total surface, while the fraction below 150 mesh contains 47 per cent of the total surface and only 1.2 per cent of the total weight. Also, one should appreciate that, in a 1-in. slack, the domestic stoker fraction (1 in. to 8 mesh) contains 76.3 per cent of the weight and 8.2 per cent of the surface, while the fraction below 150 mesh represents 3.3 per cent by weight and 54.8 per cent by surface area. Wax extraction data on 1-in. to 0 slack from mine-run treated Freeport-searn coal showed that the coating was distributed uniformly as a function of exposed surface; hence, nonuniformly on a weight basis. This distribution of the coating on mine-run coal therefore limits the extent of treating that is desirable on bituminous coal at this point in the preparation. The treatment of Freeport mine-run coal before it reached the tipple gave a 70 to 80 per cent reduction of fly-dust in the tipple, a satisfactory treated commercial slack coal, and an indicated change in the trend of tipple degradation. The premium-treated domestic sizes required a supplemental treatment for complete dustproofness. The actual cost of the pretipple and supplemental treatments was very low per ton of coal treated, while the net or true cost was sufficiently

Jan 1, 1938

By W. Edeburn, H. R. Fife

An extended study of dustproofing Freeport-seam coal has emphasized several fundamental features in the successful treating of bituminous coals. The extent of the exposed surface area and its absorption propcrties for the dust-retaining film were found to be the most critical factors affecting the efficiency of fly-dust prevention. From recently published screen data and specific surface-area measurements on United Kingdom coals, an approximation of the surface exposed by mine-run coal and by 1-in. slack was made. The total surface area exposed by an average tori of this mine-run coal was estimated at 3768 sq. yd., while a ton of 1-in. slack represents a total surface area of 8779 sq. yd. with no additions for porosity. It is important in coal treating to consider that in mine-run coal the fraction above 1/4 in. in size represents 79.5 per cent of the total weight, but only 4 per cent of the total surface, while the fraction below 150 mesh contains 47 per cent of the total surface and only 1.2 per cent of the total weight. Also, one should appreciate that, in a 1-in. slack, the domestic stoker fraction (1 in. to 8 mesh) contains 76.3 per cent of the weight and 8.2 per cent of the surface, while the fraction below 150 mesh represents 3.3 per cent by weight and 54.8 per cent by surface area. Wax extraction data on 1-in. to 0 slack from mine-run treated Freeport-searn coal showed that the coating was distributed uniformly as a function of exposed surface; hence, nonuniformly on a weight basis. This distribution of the coating on mine-run coal therefore limits the extent of treating that is desirable on bituminous coal at this point in the preparation. The treatment of Freeport mine-run coal before it reached the tipple gave a 70 to 80 per cent reduction of fly-dust in the tipple, a satisfactory treated commercial slack coal, and an indicated change in the trend of tipple degradation. The premium-treated domestic sizes required a supplemental treatment for complete dustproofness. The actual cost of the pretipple and supplemental treatments was very low per ton of coal treated, while the net or true cost was sufficiently

Jan 1, 1938

By Callaghan T

The Henty Gold Mine is located approximately 30 km north of Queenstown, at the head waters of the Henty River on the west coast of Tasmania at 41¦50'S, 145¦40'E on the Queenstown (SK 55-5) 1:250 000 and Sophia (8014) 1:100 000 map sheets (Figure 1). The mine is accessed from Queenstown along the A10 Highway and Anthony's Road. The town of Queenstown is located 260 km north west of Hobart on the A10 Highway, and

Jan 1, 1997

By G. St. J. Perrott

AN explosive of, balanced composition might be expected, on first consideration, to develop maximum propulsive strength.1 This hypothesis is based on the assumption that an excess of oxygen would act simply as an inert material with a consequent lowering of flame temperature, also that a deficiency of oxygen would tend toward incomplete reaction of the combustible materials, thereby preventing development of the full strength of the explosion. Actually, however, it can be shown both theoretically and experimentally that an explosive having a certain oxygen deficiency will develop the greatest propulsive strength. This fact has been known to the technical staffs of explosives manufacturers for many years, but it has not always been recognized by explosives engineers in the field. For example: There: is a fairly widespread opinion that the wrapper of a stick of dynamite is merely a container for the explosive and that it plays little if any part in the development of propulsive strength. Actually, it can be shown that the wrapper enters fairly completely into, the explosive reaction. In the case of most gelatin dynamites, a given weight of explosive from which the wrappers have been removed will develop considerably less strength than the same weight of explosive plus wrapper, in spite of the fact that the latter combination contains less weight of the actual explosive ingredient. It can also be shown that a cartridge 7/8 in. in diameter may be stronger, weight for

Jan 1, 1928

By E. L. Swarts

In the course of a program on high-temperature processing and electrowinning of uranium at the Knolls Atomic Power Laboratory,'' it became necessary to give attention to the interaction of molten uranium with graphite. Although it is known3 that a protective interface layer may form, details of this reaction have not been reported. Unfortunately it was impossible to complete the planned experimental program. However, the general problem is considered of sufficient interest to warrant reporting those preliminary results actually obtained. EXPERIMENTAL PROCEDURE Interface carbide layers were formed by melting samples of cleaned uranium metal in small closed graphite crucibles. Equilibrations were conducted in vacuo or in an atmosphere of dry helium at temperatures ranging from 1150" to 1400°C and for periods of from 24 to 240 hr.

Jan 1, 1960