Search Documents

By R. Neilson Clark

THE coal-beds of Canyon City are situated six miles below the town, upon the Arkansas River. At this point the Rocky Mountains have thrown out from their main ridge two spurs. The one to the north, containing Pike's Peak and Cheyenne Mountain, is known as part of the "Rim Range;" the one to the west and south is known as the "Greenhorn Range." Against these syenitic mountains, the later rocks are piled and uplifted ; at right angles to the direction of this main uplift is the axis of a lesser plication. On the north, west, and south, the pitch is steep, gradually flattening as it approaches the centre of the basin and rising again to the east at a pitch of about 5", thus forming a perfect basin, the centre of which is only three miles east of the base of the Greenhorn Range.

By R. I. Lahring, C. G. Inks

A surfactant waterflood, using a block copolymer of ethylene and propylene oxide (PLURONIC L64*), wa., started in 1956 in Kansas to determine the commercial feasibility of such a process. The production formation was the Bartlesville sand at a depth of 1,400 ft. Leares in the test area had attained both primary and secondary production peaks, and were on a normal decline when the tests were initiated. The injection wells were taking water at a reasonable pressure and none of the operating conditions were particularly unusual. The leases were selected primarily because of normal operating conditions, and not because of any serious problems demanding remedie>,. Oil production and water injection data were recorded during the 10-year test period, and their compilation indicates that the surfactant resulted in an increase of about 9 percent in secondary oil production. Other benefits derived from the surfactant injection were lower injection pressure that resulted in reduced power consumption and reduced erosion of the pumps; and lower calcium scale buildup. These fringe benefits more than offset the cost of the surfactant used. Introduction During the past several decades, considerable research has been carried out on secondary recovery of crude oil that remains in the producing formation despite the most efficient, current primary production practices. Methods are constantly sought of increasing recovery of oil, while at the same time improving the economic efficiency of operations. One method that has received intensive study over the years is the use of a surfactant as a waterflood additive. Laboratory tests show conclusively that dilute solutions of surfactants remove considerably more oil from uncon-solidated sand cores than does water alone.'- The loss of surfactant by adsorption at solid-liquid interfaces has caused serious doubt that surfactants can be used economically as waterflooding additives. This is especially true with anionic and cationic surfactants, and to a lesser extent with nonionic surfactants. This work was undertaken to determine the effectiveness in increasing oil production by injecting water containing small quantities of a nonionic surfactant. The surfactant selected was PLURONIC L64*, a block copolymer based on ethylene and propylene oxide, having the following structure The selection of the test site, a typical shoe-string sandstone type of field located at Batesville pool, Toronto District of Woodson County, Kans., was made because of its normal primary and secondary recovery operating conditions, and not because of any serious operating problems. When the tests were begun, the field was experiencing the customary post-peak production decline of a waterflood. Using for the tests a field that was on a normal production decline, while maintaining constant all variables other than the addition of the surfactant. was of varamount importance if success or failure was to be attributed to a particular cause. It was reasoned that if a surfactant was added to the injection waters and nothing else was done to influence the oil production or injection of water, the effects of the surfactant on the flood could be determined precisely. Production History The first well in the tested field was drilled in 1935. Gas repressurization began immediately, but it was not until Aug., 1938, that the major portion of the field was developed. During the period of repressurization, 1,700 MMcf of gas was injected. As can be seen from the curves of Fig. 1, the production peak from gas injection was attained in 1937 and a normal production decline followed. Early in 1942, water injection wells were drilled and injection of water Was initiated. The amount of water injected increased as more injection wells were drilled until a peak injection rate of 2,700 BID was reached in

Jan 1, 1969

This paper presents the water management plan of the Mae Moh Project in the North of Thailand, which includes a large lignite opencast mine and thermal power plants. Lignite production will increase from the present 5.5 million tons per annum to approximately 20 million tons per annum by 1995 when the pit area will be about 20 sq.km. and the depth at over 300 meters. Seven power plants are proposed of which two are under construction. The total capacity to be installed is 2,925 MW. The principles considered for water management are firstly flood protection, including drainage of the mining pit and diversion of the Mae Moh stream away from proposed future mining areas; and secondly, a plan to meet the water requirement of the thermal power plants, while maintaining downstream supplies for irrigation and other purposes. The limited annual run-off of Mae Moh and Mae Chang watershed basins are inadequate for the proposed power plants. A study has been prepared to compare two approaches, namely conveying water from remote watersheds to meet the water requirement of the power plants up to total installed capacity; or by limiting future total generation, at the existing site, to only 2025 MV.

Jan 1, 1988

By Lawson J. Taylor, Paul N. Worsey

Recent reputable evidence conclusively indicates that conventional chemical delay elements in delay detonators are notoriously inaccurate and can thus seriously affect blasting efficiency.

Jan 1, 1983

By S. R. Rao, J. Leja, K. S. Moon

A prolonged grinding of sulphide ores in steel mills appears harmful to flotation recovery and selectivity whenever xanthates are used as collectors. Particles finer than about 10µm show a pronounced decrease in floatability. A supposition was made that the cause of the reduction in floatability of ground sulphides is the presence of metallic iron abraded during grinding and deposited on the ground particles. Electro- chemical measurements were made of mixed potentials developed by different sulphide-mineral electrodes (galena, chalcopyrite, pyrite, marmatite, pyrrhotite) in xanthate solutions, without a direct con- tact or in contact with a metallic iron electrode. These measurements showed that without a galvanic contact between the sulphide and the iron, the values of mixed potentials were in the vicinity of the xanthate/dixanthogen redox potential. When contact with iron was established, the mixed potentials shifted towards the more negative reducing or cathodic values. The shift was greater the higher was the ratio of the surface areas: iron electrode to sulphide electrode. Further, the shift in mixed potentials was greater the more reducing were the conditions on the sulphide electrode. Chemical analysis of reaction products produced on the surfaces of sulphides and in the bulk solution showed that less thiosulphate was formed in all of the sulphide-xanthate systems and that more elemental sulphur was detectable on the pyrite and marmatite surfaces. Adsorption of xanthate parallels the amount of thiosulphate formed with which xanthate is exchanged by metathesis. If the supply of oxygen is limited, the demand for oxygen by the abraded metallic iron competes with that by the valuable sulphide, resulting ultimately in poorer hydrophobicity. If excessive amounts of pyrite or pyrrhotite are present as well, the conditions are so reducing that there is little adsorption of xanthate ions on the valuable sulphides to make them hydrophobic and floatable. The presence of increased quantities of sulphur on pyrite or marmatite is responsible for a non-selective flotation. Flotation tests on synthetic mixtures with and without metallic iron powder in the feed confirmed the above conclusions from electrochemical and chemical measurements.

Jan 1, 1976

By K. E. Brown, J. P. Brill, T. C. Doerr

A wide range of intermittent gas-lift tests way conducted in a 1,500-ft experimental well through 11/4- and 11/2-in, nominal size tubing. The well was equipped with two gas-lift valves, four Maihak electronic pressure transmitters and surface facilities to measure casing and tubing pressures, temperature, liquid production and the rate and volume of gas injected. For each tubing size, tests were conducted varying the slug length, gas volume injected and liquid viscosity and surface tension. From these tests, an empirical "fallback" or liquid loss correlation has been developed. No general fallback correlation could be obtained, and the correlation is presented in the form of one curve for each slug length of a given liquid and lubing size. A conceptual model has been developed which combines the fallback correlation with equarions which govern liquid slug pow. A mathematical simulation of the model in the form of a digital computer program is used to calculate total recovery, gas volume used and clearance time for a given test. Tubing pressures at the gas-lift valve and at the gm-slug interface are calculated as a function of time. Tubing pressures at the surface during slug clearance ore also calculated. The results compare favorably with the test data and verify the conceptual model. The extent to which the model can be used for other tubing sizes, depths, liquids and gas-lift valves can only be determined with additional experimental data. Data are also necessary so that a fallback curve can be constructed for the particular test conditions studied. INTRODUCTION The flow of liquid slugs in vertical conduits has long been an established production method in the petroleum industry. Under the name "intermittent gas lift", many advances have been made in engineering design. However, the unsteady-state nature of liquid slug flow has discouraged attempts to describe the problem analytically. The result has been that intermittent gas lift is dominated by rules-of-thumb engineering practices developed over many years. The advent of slim-hole completions has increased the demand for a more rigorous solution to the intermittent problem. Small-diameter conduits offer more frictional per intermittent cycle. Small-diameter conduits are defined to be 1%-in. nominal size tubing or smaller. When oil is produced from the reservoir in which it is found, and transported to surface tanks by intermittent gas lift, three separate flow stages are encountered: flow of the fluids to the wellbore through a porous medium, vertical flow of a liquid slug from the point of gas injection to the surface, and horizontal flow of the liquid slug through the surface flowlines from the wellhead to the surface tanks. The three stages are depicted schematically in Fig. 1. The present study deals with liquid slug flow in both the vertical and horizontal conduits, ending when the bottom of the liquid slug reaches the surface. Due to the large number of variables involved, the analytical study of intermittent gas lift is extremely complex. The possibility of flow regimes other than slug type, the nature of the force fields acting on the system, the interfacial instabilities involved, the varying operational principles of existing gas-lift valves and the complete unsteady-state nature of the physical phenomena occurring in an intermittent gas-lift cycle relate some of the difficulties encountered.

By Samuel Lasky

FAULTING at Kennecott, with its attendant fracturing, is unusual, complex, and important. As study. and knowledge of the various fault systems have progressed, appreciation of that importance has helped in the selection of proper horizons for exploration and in the avoidance of useless crosscutting and drifting. During the study of this faulting and fracturing, a suggestion concerning the formation of the ore-bearing fissures occurred to me. Further study in the available portions of the approximately 45 miles of workings in the Kennecott mines for the purpose of checking up the the suggestion led to the hypothesis which this paper will attempt to present. Briefly, the hypothesis may be stated as follows: The formation of transverse faults that stop against a main, system is connected with changes in the strike or dip of the main fault, and such cross faults or fractures lie in the moving block of the main fault system and indicate a change in strike or dip of the main fault. It has been found that each kind of change tends to produce definite effects and that careful study of the evidence can often suggest the exact type of change.

Jan 1, 1928

By Henry J. Joesting

During the past year and a half, the Territorial Department of Mines in Alaska has conducted a modest experimental program for the purpose of determining the extent to which magnetic and resistivity methods can be used in interior Alaska in connection with prospecting, mining and geological studies. Since little information is available concerning previous work,l,2 and since conditions differ considerably from those in most other regions, it was considered advisable to make a general study of the possibilities and limitations of the two methods, rather than a detailed study of any single problem. Problems One of the most serious handicaps to prospecting and geological study in interior Alaska, especially in the mature regions, is a cover of unconsolidated deposits ranging in thickness from a few feet to several hundred feet. These deposits, some of which are permanently frozen, consist of silt with varying proportions of vegetation and windblown material in the valleys and of residual deposits on the hills.3'4 The problems treated here are caused by the existence of this overburden: I. Location of buried placers. 2. Determination of depth and areal distribution of permanently frozen and of thawed unconsolidated deposits. 3. Location of water-bearing beds under unconsolidated deposits. Instruments and Methods Magnetic and direct-current resistivity methods were used because they are relatively simple, rapid and inexpensive and because generally they are well suited to the study of the problems indicated. The instruments used were a vertical Schmidt-type magnetometer and a direct-current resistivity instrument similar to those used by the Geophysical Branch of the U. S. Geological Survey. For placer surveys with the magnetometer, a sensitivity of about 25 gammas per scale division was found suitable. For resistivity studies of frozen and thawed overburden and of underground water, the Lee partitioning method6 was found to be most generally suitable. In the Lee method a central potential electrode is placed midway between the two potential electrodes of the Wenner four-electrode configuration.7 Nonpolarizable electrodes were made from unglazed porcelain pots about 10 cm. high and 5 cm. in diameter. In order to retard evaporation of the electrolyte the sides of the pots were glazed, inside and out, with clear Duco lacquer. For resistivity work in cold weather, a nonfreezing electrolyte consisting of equal parts of ethylene glycol and a saturated water solution of copper sulphate proved satisfactory. Stainless steel rods of 3/4-in. diameter made excellent current electrodes because their bright finish enabled good ground contacts to be made.

Jan 1, 1946

By Henry J. Joesting

During the past year and a half, the Territorial Department of Mines in Alaska has conducted a modest experimental program for the purpose of determining the extent to which magnetic and resistivity methods can be used in interior Alaska in connection with prospecting, mining and geological studies. Since little information is available concerning previous work,l,2 and since conditions differ considerably from those in most other regions, it was considered advisable to make a general study of the possibilities and limitations of the two methods, rather than a detailed study of any single problem. Problems One of the most serious handicaps to prospecting and geological study in interior Alaska, especially in the mature regions, is a cover of unconsolidated deposits ranging in thickness from a few feet to several hundred feet. These deposits, some of which are permanently frozen, consist of silt with varying proportions of vegetation and windblown material in the valleys and of residual deposits on the hills.3'4 The problems treated here are caused by the existence of this overburden: I. Location of buried placers. 2. Determination of depth and areal distribution of permanently frozen and of thawed unconsolidated deposits. 3. Location of water-bearing beds under unconsolidated deposits. Instruments and Methods Magnetic and direct-current resistivity methods were used because they are relatively simple, rapid and inexpensive and because generally they are well suited to the study of the problems indicated. The instruments used were a vertical Schmidt-type magnetometer and a direct-current resistivity instrument similar to those used by the Geophysical Branch of the U. S. Geological Survey. For placer surveys with the magnetometer, a sensitivity of about 25 gammas per scale division was found suitable. For resistivity studies of frozen and thawed overburden and of underground water, the Lee partitioning method6 was found to be most generally suitable. In the Lee method a central potential electrode is placed midway between the two potential electrodes of the Wenner four-electrode configuration.7 Nonpolarizable electrodes were made from unglazed porcelain pots about 10 cm. high and 5 cm. in diameter. In order to retard evaporation of the electrolyte the sides of the pots were glazed, inside and out, with clear Duco lacquer. For resistivity work in cold weather, a nonfreezing electrolyte consisting of equal parts of ethylene glycol and a saturated water solution of copper sulphate proved satisfactory. Stainless steel rods of 3/4-in. diameter made excellent current electrodes because their bright finish enabled good ground contacts to be made.

Jan 1, 1946

By Phelan JM

Poor selectivity in the separation of two sulphides generally arises because the flotation characteristics of the coarse sizes of the valuable mineral and finer sizes of non-valuable minerals are identical. Separat- ing the pulp into two size fractions at a specifically determined cut size and conditioning each size fraction with its own optimum reagent addi- tion is known to be helpful in improving such selectivity problems. The performance of the zinc section of the complex ore circuit at Wood- lawn Mines has been analysed in detail. The selective recovery of zinc was found to be a problem in zinc/pyrite separation. However, atypi- cally, the separation problem was between coarse zinc and coarse, not finer, pyrite. In spite of this the use of separate conditioning has effected significant improvements in rougher concentrate. Selectivity (and hence grade), overall recovery and flotation rate have all been enhanced. Dis- appointingly, coarse zinc recovery was not increased but, with careful optimization, this might be achieved without sacrificing the gains already realized. The technique of separate conditioning clearly has general application in other circuits where selectivity is a significant problem.

Jan 1, 1988

By R. L. Jones, D. D. Runnels, D. P. Dupon, D. J. Cline

To establish meaningful remediation goals and monitoring programs in areas disturbed by mining and associated industries, it is desirable to determine the natural concentrations of metals that existed in these areas prior to being disturbed. In mineralized areas, multiple natural populations of metals and associated components may be present. This paper describes a method for characterizing the natural background chemistry by means of probability distribution dia¬grams. The method can be applied to water, soil and other natural materials. In a study of a complicated hydrogeologic system at the Kennecott Utah Copper North and South Operational Areas near Salt Lake City, UT, probability distribution diagrams were used to differentiate between natural background waters and waters impacted by human activities. The probability distribution diagrams allowed a component-by-¬component interpretation of the chemistry of ground¬water and surface water over a large geographic area. Natural chemical background populations and anthro¬pogenic effects were identified Although the method is illustrated for mining-related sites, the same approach can also be used for other natural and anthropogeni¬cally impacted sites.

Jan 1, 1999

By Courtenay de Kalb

So far as the writer is aware, no detailed investigation into the behavior of ores or rocks when subjected to crushing under digerent conditions has yet been made. He cannot himself claim to have carried such investigations very far; but the results of some studies which he has been pursuing for a couple of years, as opportunity permitted, seem sufficiently interesting and suggestive to warrant a brief statement of them, preliminary to nildertaking a more exhaustive course of experiments. Criticisms and suggestions are earnestly invited, with a view to making these studies as instructive as possible. As a part of the examination of ores, preparatory to concentration, my students have been required to take lots of 100 pounds each, and crush them. These are then screened through a series of hand-sieves, 15 inches in diameter. The products remaining on each screen are weighed, and from the results is plotted a curve, called the sizing-curve. It was assumed at first that different ores would yield, under like conditions of crushing, curves showing unlike characteristics as to the quantities remaining on the various sieves. After a number of such curves had been obtained it became evident, as often happens, that this a priori reasoning was faulty. The curves presented practically identical characteristics, and only by varying the crushing-conditions were variations in the curves obtainable. Another peculiarity, which was as little anticipated, appeared by inspection of these results, namely, that successive crushing to smaller sizes did not greatly augment the quantities of the filler products, so long as the machines employed applied the crushing-force to the ore-particles in the same manner. In these experiments the fines were not eliminated between successive crushings. I believe it will be readily admitted that rock can be crushed

Jan 1, 1899

By E. S. Greiner

THE hot working of chromium was first reported by Hunter and Jones; who used small pellets of the material obtained by the reduction of chromium chloride with sodium. Later, the working of chromium at 600° to 1100°C was reported by Marden and Rich,2 and at 1250°C by Kroll3 The hot rolled material3 had a Brinell hardness of about 150 (62.5 kg, 2.5 mm ball, 1 min) and was brittle at room temperature. Except for that associated with hardness indentations, no plastic flow in chromium at room temperature has been reported to the author's knowledge. Studies described here have shown slip markings in chromium after deformation at room temperature.

Jan 1, 1951

By M. H. Moys

A method of estimating the percent solids in the discharge from a grinding mill is described and tested on both pilot and industrial scale. It involves the use of energy and mass balances around the mill discharge sump, requiring measurements of the flowrate and density from the sump together with temperatures of all streams flowing to and from the sump. Accurate estimates of the dynamic variation of mill discharge percent solids are made available, provided that occasional manual sampling of the stream is done to cope with drift in instrumentation. The use of a computer in this application was essential; the various advantages associated with its use are discussed. It is anticipated that this estimate of discharge density can be controlled at a set point by manipulation of the water fed to the mill, resulting in significant decreases in specific power consumption and media consumption.

Jan 1, 1987

By C. Chongo, F. X. Paquot, C. Ngulube

"Over the last six years, the Kansanshi copper-gold mine has continued to process significant quantities of complex transitional mixed ores. Initially, the ore treated came predominantly from accumulated stockpiles. Subsequently, the feed source shifted primarily to freshly mined ore that generally showed less tarnish with better flotation kinetics, but with the downside of lower concentrate grades. A number of changes were made to improve the efficiency of the rougher circuit and quality of concentrate produced. These changes were as a result of initial mineralogical studies and laboratory flotation test work that were discussed at length in a previous paper1. Salient among the recommendations adopted as a result of previous work were increased circuit capacity and a modified configuration to increase the residence time and the number of sulphidization stages. These modifications were completed and commissioned in 2011. This, however, resulted in significantly low rougher concentrate grades and a below-specification final concentrate product. This was due primarily to higher mass pulls from the extended rougher bank with multiple concentrate discharge streams, and which necessitated an enlarged cleaning capability. The extra cleaning capacity came on stream in 2014. Of note was the development of a recovery model, based on the strong correlation between the total copper and acid-soluble copper ratio, as a tool for monitoring plant performance. IntroductionThe Kansanshi mine, the largest copper mine in Africa, is 80% owned by Kansanshi Mining plc, a subsidiary of First Quantum Minerals. The remaining 20% is owned by the state through the parastatal Zambia Consolidated Copper Mines Ltd (ZCCM). The mine is located approximately 10 km north of the town of Solwezi and 180 km to the northwest of the Copperbelt town of Chingola. The mine has been in commercial operation since 2005."

Jan 1, 2016

By Diehl GW, Kuntonen J

The Tamrock all-hydraulic rock drilling system 400 has been developed to cover as wide a drilling range as possible, from 35 mm holes in tunnelling, roofbolting and development work to 64mm holes in long hole production drilling. Field experience during the last five years shows that the Tamrock drill covers this range in a way that no other rock drill on the market does and recently the range has been success- fully further expanded to cover bench drilling with 76 mm holes.

Jan 1, 1978

By McNicol J. H

Using a small scale laboratory pilot plant a series of tests have been conducted with the aim of investigating the influence of the zinc/acid ratio on the efficiency of zinc electrodeposition from an acidic sulphate solution. The results have shown that current efficiency is increased as the zinc/acid ratio is increased with no evidence of an optimum zinc/acid ratio. However the choice of a zinc/acid ratio for full scale operations must be a compromise between other parameters, spent electrolyte acidity and power efficiency, which also impact upon plant performance. The effect of various impurities has also been monitored and antimony, nickel and tin have been shown to be deliterious to current efficiency.

Jan 1, 1989

By M. J. Virnig, Marc Le Vier, Rong Yu Wan, Jan D. Miller

Although most gold production from primary resources is achieved by cyanidation, many research activities have focused on alternative processes using noncyanide lixiviants. Such research has been prompted by environmental concerns and problems associated with the processing of refractory gold ores. Numerous research projects have been conducted to search for a noncyanide hydrometallurgical process for gold extraction. In this paper, a technical review of gold recovery from noncyanide solutions is presented, and new results are reported. Gold recovery techniques that are considered include activated carbon adsorption, cementation, solvent extraction, ion exchange, and reduction-precipitation.

Jan 1, 1993

By H. C. Roland Kammel

Stannous sulfate electrolytes are widely used nowadays in electrolytic tin production. Characteristic features of this electrolysis process are that dense cathode deposits can only be obtained by additions of organic additives and that so called ?black mud is formed on the anode surface which leads to an increase in cell-voltage. In order to prevent excessive cell-voltages or oxygen evolution the black mud has to be removed periodically. Studies in laboratory scale have been performed about the effect of different organic additives on electrolytic tin deposition and the formation of surface layers on pure and industrial tin anodes. Results reveal that organic addition agents are effective in reducing cathode roughening as well as extending the covering time of the anode ?by black muds.

Jan 1, 1985

By H. J. Sloman

Mining laws of the several coal-producing Stat e with respect to safety catches on mine cages and their testing are extremely variable and generally indefinite in scope. The most specific requirements are contained in the Coal Mining Laws of Washington,3/ as follows:

Jan 1, 1944