Search Documents

By Stephen H. Stow

A relationship exists between the color and the chemical composition of the pebbles from the Bone Valley Phosphate Formation. Darker-colored pebbles are relatively high in iron oxide and relatively low in calcium phosphate when compared to lighter-colored samples; the brown color of the phosphate pebbles can be correlated with their iron content and the black and gray colors with their organic carbon content.1,3 It was anticipated that the darkness of a phosphate sample might be quantitatively measured by a simple reflectivity test and that the amount of reflected light could be correlated with the chemical composition of the rock, especially with the elements which cause the color and darkness of the Florida phosphates. Twenty-one samples of production grade phosphate rock from Hillsboro County, Fla., were studied. All samples were ground to -200 mesh for reflectivity tests and analyses. All analyses are accurate to well within ±2% of the reported value, except for aluminum and organic carbon, which are accurate to only ±15% of the reported amount. Reflectivity measurements were taken with a model 610 Photovoltmeter for tri-stimulus amber, blue and green, and white lights. Experimental procedures and data are available upon request. Results Table 1 contains linear correlation coefficients (LCC) for the element-reflectance relationships for the samples. The top portion of the table refers to the LCC between the percent of light reflected off the samples and the percent of a given element (or its oxide) as analyzed. In the lower portion of the table the LCC refers to the relationship between the same reflectance data and the chemical analyses which have been corrected on the basis of 0% acid insoluble material (chiefly quartz) in the phosphate rock. Each LCC presented in Table I is computed for the 14 coarser samples exclusive of the seven concentrates since the concentrate samples appear to have anomalous reflectivities upon comparison with the coarser grades. Only the most significant LCC for each element is presented in graphical form. Discussion of Data Iron: [Fig. 1] is a graph of the relationship between iron and reflectivity (LCC = - 0.98). A good correlation with Fe2O3, is expected due to the relationship between the tan (or brown) color and the abundance of iron oxide, the principal mode of occurrence of iron in Florida phosphates.8 Note the location of the seven triangles which repre-

Jan 1, 1972

By S. D. Thompson

An AIME transaction by P.L. Allsman (1960), "Analysis of Explosive Action in Breaking Rock," contains many useful concepts applicable to blast design. Of special interest was the derivation of a heave blasting burden formula, which is important in establishing the maximum burden. Unfortunately, its derivation contains a fundamental error and then a compensating one. This formula was: [bImpulse _P d At max =nwuwu where: bmax = maximum burden in m (ft). P= average detonation pressure in N/m2 (lb per ft2). A= duration of the average detonation pressure in sec. n= 3.1416. w= specific weight of rock in N/m3 (lb per ft3). u= minimum velocity that must be imparted to the rock in m/sec (ft per sec). d= borehole diameter in m (ft).] The derivation used the impulse-momentum principle, with a 0.3 m thick (1 ft thick) radius of rock mass being acted on by an explosive impulse. However, the rock weight was not converted to mass by dividing by the gravitational constant. This mistake can be verified by checking the units in the formula, which resolve into m1/2-sec instead of meters. Adding the gravitational constant corrects this: [P d Atbmax =gu g = gravitational constant equal to 9.81 m/sect (32.2 ft per sec2).] If the minimum velocity is now taken as 0.3 m/sec (1 ft per sec), as was recommended, excessively large burdens result. Any appropriate rock velocity should be capable of throwing the rock mass a minimum distance so that the swell needed for breakage can occur. Unless the burden is extremely small and the bench height is very high, it is unlikely that a velocity of only 0.3 m/sec (1 ft per sec) will be sufficient. A review of the literature indicates that average rock velocities observed by camera studies typically range from 15 to 30 m/sec (50 to 100 ft per sec) (duPont deNemours and Co., 1977; Tansey, 1979). On this basis, a minimum rock velocity of about 15 m/sec (49 ft per sec) would be expected and not 0.3 m/sec (1 ft per see). When a velocity of 15 m/sec (49 ft per sec) is inserted into the corrected formula, the results approximate those of the original formula with a velocity of 0.3 m/sec (1 ft per sec). The errors were approximately self-compensating [(9 = 1.24)]. ? References Allsman, P.L., 1960, "Analysis of Explosive Action in Breaking Rock," Transactions, AIME, Vol. 217, pp. 475-476. E. I. duPont deNemours and Co., 1977, Blasters' Handbook, 175th Anniversary Edition, Dupont, Wilmington, DE, pp. 233. Tansey, D.O., 1979, "The DuPont Sequential Blasting System," CIM Bulletin, Vol. 72, July, p. 80. Thompson, S.D., 1981, "Critical Review and Revision of Surface Blasting Practice," MS thesis, West Virginia University, pp. 308-316.

Jan 1, 1986

Recovery of Precious Metals from Chloride Solution by Magnetite The development of environmental-friendly lixiviants as alternatives to cyanide and the increasing recycling activities to recover precious metals from waste materials have prompted researchers to find efficient methods and alternative sorbents to recover precious metals, such as Au and Pt, from aqueous solutions. This study explored the use of magnetite (Fe3O4) as a sorbent to recover Au and Pt from chloride solutions. Magnetite is a semiconductor and has the capability of transferring electrons both within the solid state and across the solid-liquid interface and has the ability to reduce metal species on its surface. The sorption of AuCl4- and PtCl62- from NaCl solution on commercial grade magnetite powder was investigated by batch-sorption experiments. The effects of pH, contact time, NaCl concentration and precious metal concentration on the recovery were studied. Sorption experiments revealed that magnetite exhibited selectivity towards other metals with the strongest affinity for Au. Both Au and Pt recoveries showed similar pH dependence curves, with peaks at pH 6 - 7. At this pH range, a maximum of 4.4 ¦mol Au/g Fe3O4 and 3.0 ¦mol Pt/g Fe3O4 were recovered after 24 h at an initial metal concentration of 0.05 mol/m3. Increasing the initial precious metal concentration increased the Au and Pt uptake amount by magnetite. It was also observed that the recovery decreased with high NaCl concentrations. The SEM images of the magnetite particles after the treatment showed that gold, which was confirmed by the EDX analysis, agglomerated and were deposited on Fe3O4 surface.

Sep 13, 2010

By U. Dillon, G. Blackwell

"Geographic information systems (GIS) provide an efficient means for the recording, manipulation, revision, display and analysis of spatially referenced data. GIS are widely used at the exploration stage of mine development, and are increasingly used for reclamation planning. The ability of a GIS to perform spatial searches and query spatially referenced data make it a powerful tool for use at all stages of mine development. As the amount of data available for analysis increases, so does the power and flexibility of GIS as a planning tool.Starting from the exploration database, this paper describes how a GIS can be used for the development of mining plans based on topography, geology and mineralization information stored in a relational database. Planning decisions approaching the optimal can then be made for a wide range of parameters, including stockpile and waste dump locations, the location of potentially acid generating and neutralizing material for dump design, profitable and risk-controlled mine extraction sequencing, and haul road locations. This is made possible by the overlay and buffer analysis capabilities of a GIS which are explored and exploited to produce a continuous mine production planning program, as well as site remediation and reclamation using a successful case study. IntroductionGeographic information systems (GIS) are a relatively new tool in the mining industry. Although they have existed for a number of years, the potential of GIS for mine management and planning is only beginning to be investigated and exploited. The unique spatial capabilities of GIS make them particularly wellsuited for use in mining, where spatial information is fundamental to the processes of mineral exploration, mine development, and environmental reclamation. A number of potential applications for GIS in the mining industry have been identified, and they are widely used for exploration and reclamation. The use of a GIS as a platform for the development of mine planning routines and software remains an interesting, but as of yet unexplored, application of this technology."

Jan 1, 2003

By C. G. Dunn, J. L. Walter

COULOMB' and Coulomb and Lacombe2,3 have recently discussed secondary recrystallization in soft iron (99.5 pct Fe). They found that the appearance of this phenomenon was dependent on both the presence of impurities and the thickness of sheet specimens. They concluded that impurities such as carbon, sulfur, and oxygen in the soft iron stabilized the matrix structure and allowed growth of a few grains of specific orientations. They also found that secondary recrystallization ceased when the final thickness was small and attributed this complete inhibition of growth in thin sheet to the restraining action of thermal grooves. When purer iron (99.99 pct Fe) was used, normal grain growth but not secondary recrystallization was obtained. On the other hand it is known that the necessary stabilization of the matrix structure for secondary recrystallization in high-purity silicon iron probably does not depend on impurities but more likely results from the specimen thickness effect of Beck et al.,4 according to evidence and ideas advanced by Walter and Dunn,5,6 and Detert.7 Furthermore, Mullins8 has indicated that if a gas-metal surface energy difference exists across a grain boundary equal to or greater than about 3 pct of the grain boundary energy, then such a grain boundary should not become stuck. Similarly, Walter and Dunn have estimated that any increase in restraining force due to increased thermal grooving with decrease in

Jan 1, 1962

By W. D. Steele, S. D. Brady

The Pittsburgh coal seam in West Virginia contains the largest coal reserves of any coal seam in that State and is, therefore, one of the most important seams, and attains minable thickness and purity throughout that part of the seam extending from the Northern Panhandle to Monon-galia Co. thence south and southwest across the state to Wayne Co. near Hunt-ington. The Pittsburgh coal is also minable in the Upper Potomac region but is now practically exhausted there. The total minable areas of this coal amount to 2,165 sq miles and are estimated, by the West Virginia Geological Survey, to contain 13¼ billion net tons. The largest body of Pittsburgh coal outcrops on the western edge of West Virginia, along the Ohio River as far south as Moundsville, West Va., going under the river at that point and extending at various depths down the river as far as Wetzel Co. line where it thins out to such an extent that it has little practical value, and on the eastern edge this large body outcrops along the Monongahela River. The territory to be covered by this paper is the area known as the Northern West Virginia District comprising Wetzel, Mon-ongalia, Marion, Preston, Harrison, Dodd-ridge, Taylor, Barbour, Upshur, Lewis, Gilmer, Braxton and Calhoun Counties, and is also known as Dist. 3 under the Bituminous Coal Act. This region was originally opened for commercial mining along and adjacent to the Monongahela River around 1852 when the Baltimore and Ohio Railroad was constructed to Fairmont. It has been extensively developed, first, in 1880 (when the Monongahela River Railroad, now B. & 0. R. R., was constructed) between Fairmont and Clarksburg, and later, in 1916, between Morgan-town and Fairmont when the Monongahela Railway was constructed and placed in operation, this area furnishing the major portion of the production over the past years. With the mining out of a great deal of this territory adjacent to the Mononga-hela River considerable interest has been developed in the back acreage; and within the past few years a number of diamond core drill holes have been made in the back areas of Monongalia and Marion Counties. In this back area the oil and gas well drilling showed that the Pittsburgh coal seam was of minable thickness and ranged in depth from 350 to 1,000 ft below the surface of the stream valleys but this drilling did not furnish any definite data as to its thickness and quality. Economic Importance The Pittsburgh seam in Northern West Virginia is of primary importance as a coal resource not only because of its large reserves but because of its contributing a very large part of the coal used in this country for general steam uses. The Pittsburgh seam is a consistently thick seam, averaging 8 ft in thickness, with very easy grades underground, so it has always been

Jan 1, 1949

By Du Sichen, S. Seetharaman, Wei Liu

"The viscosities of two-phase mixtures are of great importance in the modelling of the fluid flow in metallurgical processes. For example, in steel making and refining, the intimate mixing of metal droplets in the slag phase requires a consideration of the effective viscosities for the mixture. The present work was aimed at an understanding the phenomena underlying the viscous flow in a two-phase mixture with widely differing viscosities.Emulsions of silicone oils of known viscosities (345mPa.S and 1010mPa.S at 293K) with small amounts of water evenly distributed in the same were prepared by subjecting the mixture to uniform stirring using a magnetic stirrer. The viscosities of these emulsions were measured at constant temperature by rotating cylinder method using Brookfield Digital Rheometer. The uniformity of the preparation of the emulsions was confirmed by the reproducibility of the results. Th7 measured viscosities were generally found to be independent of the torque under the experimental conditions so that the two-phase mixture could be considered as a Newtonian liquid. The variation of viscosities with temperature and the effect of addition of a surface-active substance were also studied in this work.The measured viscosities were found to be· higher than those of both pure water and silicone oil. The experimental viscosities were found to increase with increasing concentration of water. The influence of surface tension on the viscosities was examined by adding surfaceactive agent to the mixtures. The result is discussed and compared with theoretical models developed by Einstein, Taylor and Oldroyd."

Jan 1, 2000

By John V. Beall

It is difficult to understand why they did it. It was a demonstration of total commitment which sent chills of mixed admiration and fear up and down your spine. The scene was the bodega in Section A, 2660 Level on the 12 to 8 shift. The jefe was patiently waiting for the tea leaves to settle in a large metal cup. His attention was distracted by the appearance of a miner who had a problem. The long and short of it was that the miner believed the branch raise he was driving was unsafe and he wanted the jefe to come and see it. After lunch the jefe went around. First cautiously shining his light to peer up the raise from outside the chute, he then scrambled inside and swiftly climbed the cribs to the face. No question, it was hairy; about 4 crib sets were needed to catch up to the face. The unsupported raise was slabbing. It didn't take the jefe more than a few seconds to ascertain this situation and to slide back down. As he came out of the chute, a small avalanche arrived on his heels and provided a sort of exclamation point to his order; "cerrado!" In other words, shut 'er down.

Jan 1, 1970

By C. C. Miller, C. A. Hutchinson, A. B. Dyes

This paper presents a simple and practical method for the estimation of effective permeability and reservoir pressures from the rise in bottom hole pressure when a well is shut in. The equations on which the method is based consider a stabilized well producing from a uniform formation when flow is shut off at the sand face followed by the unsteady state flow of a compressible liquid from regions far from a well to points closer in during the build-up period. An approximation for extending the method for two-phase flow in the reservoir is also presented. In order to compare the effects of extremes in the conditions existing at the external boundary of the reservoir, two general equations defining the build-up characteristics of the reservoir are shown: first, for a reservoir with constant pressure maintained at the radius of drainage, and second, for a reservoir with no influx over the radius of drainage. These equations define the build-up characteristics for the shut-in well as functions of time, the permeability and porosity of the drainage area, the viscosity and compressibility of the fluid flowing, the production rate prior to shut-in, and the radius of drainage of the well. When a well is shut in at the surface, rather than at the sand face, flow will continue into the well bore after shut-in due to the compressibility of the fluids in the bore. The effect upon the build-up characteristics of this flow into the well after shut-in has been studied by means of the electrical analyzer. From the basic relationships and consideration of the limitations due to continued flow after shut-in, methods have been developed for the estimation of the effective permeability of an area from the plot of the build-up characteristics of the well producing that area. Likewise, equations are presented for the estimation of the reservoir pressure from an early portion of the build-up curve. By means of the electrical analyzer, studies have been made concerning the variations in the build-up characteristics resulting from damaged or improved permeability in the immediate vicinity of the well bore. These studies show that the permeability estimated from the build-up curves represents the average effective permeability of the majority of the drainage area and that the permeability in the immediate vicinity of the well does not affect this estimate. Since the major portion of the drawdown is in the immediate vicinity of the well, variations in the permeability of this area greatly affect the productivity of the well as expressed by the productivity index. From pressure build-up and productivity index tests the ratio of the permeability of some arbitrarily specified area immediately surrounding the well and the effective permeability in the majority of the drainage area can be computed. This ratio is a measure of any damage to the well incurred in drilling or reworking and likewise any benefits as a result of remedial measures. In build-up tests and many other tests that are made on a producing well it is at least desirable, if not absolutely necessary, that the well be stabilized prior to testing. A method is presented here for relating the time required to stabilize a well and the reservoir and fluid properties. An equation is also presented for approximation of the length of shut-in time required to obtain sufficient build-up data for the estimation of permeability and reservoir pressure.

Jan 1, 1950

By J. L. Gillson

The big mass of anorthosite in the Lake Sanford district and the bodies of titaniferous magnetite that occur in a small area near the south margin of the mass have been described repeatedly, and the puzzling problems of the genesis of the rocks and ores have stimulated the deductive reasoning of geologists for a hundred years. Some of these men have taken a leading part in describing the anorthosite rock and forming hypotheses concerning its origin; some have contributed most to the study of the ore deposits; and some have made classical Studies introducing a basic approach to the problems of the anorthosite rock and genesis of the titaniferous magnetites. Much of the writing on the problems of rock and ore genesis has been based on physical-chemical reasoning rather than on field and microscope observations of the rocks and ores. Most of these geologists conclude that the anorthosite was formed by true magmatic crystallization, involving previous settling or squeezing out of ferromagnesian minerals from the parent magma. The associated gabbro is a separate segregation or later intrusion, and the lighter colored and finer grained facies of the anorthosite is either a chilled border zone of the anorthosite or the result of granulation by crushing of the coarse, dark blue rock of the main mass. This blue rock, called the Marcy type, is named after the highest peak in the range. The finer grained and lighter colored rock is called the Whiteface, after another mountain appropriately named for a cliff colored by this facies of the anorthosite.

Mar 1, 1956

By B. H. Caudle, M. D. Witte

In predicting the performance of a pattern injection operation, the engineer needs to know both the amount of oil to be recovered and the rate at which the recovcry will take place. This paper- describes fluid flow model studies on the effect of mobility ratio on the rate of oil recovery in a five-spot. The results show the change in fluid conductivity (total flow rate/pressure drop) as the sweep-ont pattern increases for mobility ratios between 0.1 (and 10. There data, when cornbitted with a knowledge of reservoir permeabilities and sweep-orit pattern efficiencies, cata he used to predict the cLrmulntivr oil production as a function of time for homogeneous five-spot injection systems. INTRODUCTION The flow potential in a pattern flood element is a function of the mobility ratio and how far the injected flood front has gone.1,2 For a waterflood project having a mobility ratio of one, the conductance—which is the flow rate per unit pressure drop (q/Ap)—-will remain the same throughout the life of the flood. If the mobility ratio is favorable ( < I), the conductance of the project will drop continuously throughout the operation. If, on the other hand, the mobility ratio is unfavorahlc. the conductance ratio will increase continuously. Therefore, if the reservoir engineer wishes to predict either the rate at a specified pressure or the pressure at some rate for a secondary recovery project, he must know how the conductance will vary during the flood. Other investigators have studied this problem using potentiometric models&apos; or analytical solution&apos;. The

By Z W. Orndorff

Excavation through sulfidic geologic materials during construction activities has resulted in acid rock drainage (ARD) related problems at numerous (>40) locations across all five geologic regions of Virginia, USA. Potential acidities ranging from >100 to develop a statewide sulfidic materials risk map; document ARD impacts to soil and water quality and engineered structures; and develop methods to assess site-specific risk potentials within a given highway corridor. A statewide sulfidic materials GIS risk map was developed based upon the state digital geology map which assigned four levels of relative risk to all mapped strata based upon predicted lime requirements and probabilities of encountering highly reactive materials. Non-highway construction activities have also routinely disturbed sulfidic materials, and a recent airport project in northern Virginia resulted in over 150 ha of extremely acidic (pH 45 mg/L) run-off from this site heavily damaged a receiving stream, partially due to the fact that it dissolved the galvanised steel water control structures in stormwater detention basins, leading to direct discharge of run-off and sulfidic sediments. The airport area was treated and revegetated in 2002 with a combination of lime-stabilised biosolids, straw mulch, and acid-tolerant grasses. Water quality in a receiving second-order stream quickly responded to the treatment, but some release of N was also noted as a secondary effect. Collectively, these results point out the importance of accurately assessing the potential for excavation of sulfidic materials in construction environments, and the necessity of developing toxic materials handling strategies similar to those employed in mining environments.

Jan 1, 2003

By W. A. Krivsky, R. Schuhmann

PREVIOUS papers in this series on the thermo-•t dynamics of copper-smelting systems have presented a survey of the field and an outline of the overall program: thermodynamic studies of iron silicate slags, 2-4 and thermodynamic data for simple mattes in the Cu-S system.5 Since this program was started, an excellent summary of the whole field of physical chemistry of copper smelting was published by Ruddle. The present paper represents a further step in the study of liquid mattes, and deals specifically with the Cu-Fe-S system. The importance of the Cu-Fe-S system to copper smelting is evident from the fact that these three elements constitute 90 to 99 pct of the totalweight of most commercial mattes. In copper mattes oxygen is an important fourth component. Oxygen was rigorously excluded in the work to be described in this paper. However, the behavior of oxygen in mattes was the subject of a companion research by Lander&apos; which will be described in a subsequent publication. Several studies have been made previously of phase equilibria in the Cu-Fe-S system,8-10 so that the ternary phase diagram is fairly well established in most regions. Also, separate studies have been made of the phase diagrams and thermodynamic properties for the three binary systems: CU-S,5,12-15 CU-Fe,11,14,17 and FeS.11,14,16,17 However, no work has

Jan 1, 1958

By Robert L. Voss, Richard D. Hagni

Sparry dolomite from all of the operating mines in the Viburnum Trend of Southeast Missouri have been found by cathodoluminescence microscopy to reveal a systematic pattern of banding resulting from a growth zoning within individual dolomite rhombs. Four principal bands have been recognized throughout the entire Trend and each of the major bands contain even finer internal banding. Minor bands a few microns in width can be correlated in specimens collected ten&apos;s of kilometers apart along the trend. The first three principal dolomite bands decrease from south to north. This feature, together with the fact that the white sparry dolomite crystals decrease in abundance from south to north in the Trend, suggests that a major source for the fluids was from the south. The application of cathodoluminescence microscopy to crystalline dolomite demonstrates a strong correlation between ore grade and the intensity of internal banding and dissolution textures.

Jan 1, 1985

By J. Stachulak, M. Scobie

"This paper addresses the occurrence and indicated causes of conveyor fires in North American and European underground mines. Some significant convey or fires which have been experienced in recent years in Canadian hardrock mines are then reviewed. The nature of existing conveyor monitoring technology is considered in the context of such fire hazards. Experiences with new monitoring technology recently installed at several conveyor sites at Inca Ltd. mines are then reviewed.IntroductionFires associated with conveyors have long been recognized as a serious hazard in underground coal mines. Recently, however, there have been some significant conveyor fires in Canadian underground hardrock mines. These offer important evidence as to the nature and causes of potential hardrock mine fifes. They also warrant attention with a view to improving over-all mine design, ventilation and emergency preparedness.In addition, a new era in mine communications and monitoring technology has been entered which should offer improved capability to protect against such fires. This paper was motivated by the need to understand the causes and mechanisms of conveyor fires in order to improve their safety. This should be possible through implementing more effective monitoring systems, as well as improving conveyor design. Underground mines are becoming more intensively mechanized, with less human surveillance of equipment and a greater dependency on remote monitoring systems."

Jan 1, 1992

By J. S. Redpath

Eighty feet of overburden, thirty feet consisting of fine, water-bearing sands, was encountered during the construction of a shaft collar for Chimo Gold Mines Limited at its Louvicourt, Quebec, property. This paper describes the excavation and construction methods used on the project. Open-cut methods, a sheet pile cofferdam, chemical grouting and special blasting methods were used during excavation. Concrete placement was hampered in the lower portion by a heavy water flow, and aided in the upper portion by an unusual method of form bracing. Plant and • pum11ing facilities are also described.

Jan 1, 1966

By E. Berl

THIS may be a most unnecessary paper-from what does crude oil come and how was it formed? Many people, inside and outside of the petroleum industry, believe that we have actually enough oil, and that we can easily produce very important products from this extremely valuable raw material. The writer believes, however, that the answer to this question concerning the parent material and the formation of oil is of broader interest, because it may be that from the answer to these problems it would be possible to get answers to other important indus-trial questions. Therefore, a study in this line seems to be justified, and the writer will submit some of the results which he has collected during more than ten years with many very capable collaborators, to whom his thanks may be expressed on this occasion.

Jan 1, 1938

By J. W. Halley, G. L. Plimpton

Because of the two distinct stages in the solidification of rimmed steel, segregation in the rimmed ingot is more complex than that in the killed or semikilled ingot. In the earlier stage, chemical reactions, resulting in evolution of gas and vigorous stirring of the metal, effect a degree of negative segregation unique to rimmed steel. The composition of this zone constitutes the principal quality advantage of this type of steel. In the later stage of solidification, after the evolution of gas has ceased, the segregation follows the general pattern of a more completely deoxidized steel. However, the composition of the liquid remaining after the first solidification stage varies markedly from that of the original melt, some constituents having been partially removed as reaction products while the concentration of others has been intensified by rejection from the metal solidifying in the first zone. The aim, from the standpoint of segregation, in rimmed steel of high quality is to effect a maximum negative segregation in the rim zone without excessive concentration of undesirable elements at the center of the ingot. To achieve this aim, the composition of the melt may be varied and the furnace and pouring practice may be adjusted within certain limits. It is the purpose of this study to discuss segregation in rimmed steel from the standpoint of the mechanisms that produce it and to survey the phases of open-hearth practice that influence those mechanisms. Mechanisms Producing Segregation The mechanisms that determine the degree of segregation in the rimmed ingot are closely interrelated, making it difficult to select the primary factors and to determine a satisfactory order for presenting them. For instance, the question of sulphur segregation is relatively simple, since sulphur is not directly involved in chemical reactions in the ingot; but its concentration in the rim zone is dependent not only on its original analysis in the melt, its segregation coefficient, and the freezing rate, but also on the rate of its removal from the impure film on the solidifying surface. This washing action involves all the factors (such as freezing rate, the carbon-oxygen product, pressure, etc.) that determine the rate of gas evolution and hence the efficiency of film removal. Sulphur distribution between the rim and core is affected by the volumetric ratio between the two zones, and its segregation in the core is a function not only of the freezing rate of the core but also of all the foregoing factors that determine its concentration in the metal when solidification of the core starts. To simplify the presentation, it is proposed to treat the mechanisms affecting segregation independently in this section, reserving a discussion of their over-all effects for the section in which actual segregation data are given. The factors affecting segregation will be treated in the following order: (I) differential solidification, (2) removal of constituents as

Jan 1, 1945

The February General Meeting of the Institute was held in Kelvin House, Johannesburg, on 19th February, 1969 at 4.30 p.m. Mr R. C. J. Goode (President) was in the Chair. There were also present forty-six Members, including Messrs H. E. Cross, A. R. C. Fowler, P. Lambooy, D. G. Maxwell, Dr J. T. McIntyre, Messrs J. A. Nixon, V. C. Robinson and P. W. J. van Rensburg (Council Members), Messrs G. Abdinor, H. F. Allan, R. E. Barnes, M. M. Bayley, J. K. Boyd, R. R. M. Cousens, R. E. F. Cowley, D. Savile Davis, H. J. Davisson, C. T. Fenton, J. Fergusson, J. Fritz, M. L. Fitzgerald, J. M. Gosnell, J. C. Hall, S. A. Hancox, D. M. Jamieson, Dr D. G. Krige, Messrs J. E. V. Leeuwen, A. Louw, C. F. Louw, B. H. L. Leach, R. B. MacGillivray, C. S. McPhail, E. Margo, G. G. Nicolson, E. Pavitt, M. P. Pearse, F. O. Read, Dr M. D. G. Salamon, Dr H. S. Sichel, Messrs D. Storrar, S. G. Taussig, A. H. Taute, E. B. Viljoen and P. A. von Wielligh. Sixteen Associate Members, including Messrs S. T. Baron, W. M. Fitzpatrick, M. R. Fuller-Good, P. R. Garcia, H. G. Gericke, P. D. Hatfield, R. Hemp, G. S. Lee, Miss V. E. Marting, Messrs A. H. Munro, R. C. Power, O. F. Rheeder, G. C. Thompson and N. Zolezzi. Two Graduates, Messrs D. Bosley and J. C. Sutherland. Three Affiliates, Messrs R. K. Briggs, A. B. Cook and G. M. Thain. One Student, Mr P. W. Henrard. Twenty-three Visitors, including Messrs N. J. W. Bell, R. G. Bushell, A. Bryan, J. F. Cillie, C. M. de Beer, Dr F. H. Deist, Messrs D. S. Drake, P. G. du Plessis, R. W. Hodgson, D. M. Hawkins, S. C. H. Kearns, M. D. Labuschagne, L. Munro,R. Murchison and L. Robinson. Secretary, Mr D. C. Visser. Total present: Ninety-two. OBITUARIES The President: "It is my sad duty to announce the death of the following members of the Institute. Edward Frank Jud Bulman, Life Member, who joined the Institute in 1931 and passed away on 7th November, 1968. Elmar Fenton Chapin, Member, who joined the Institute in 1941 and passed away on 17th November, 1968. Solly Rabinowitz Rabson, Member, who joined the Institute in 1944 and passed away on 13th February, 1969. Mr. Rabson was the holder of two certificates of merit for papers presented to the Institute.

The Drummond Basin is a large intracratonic basin which developed in central Queensland during Late Devonian to Early Carboniferous times. It is postulated that the Drummond Basin developed as a foreland basin, to the west of a probable west dipping continental margin volcanic arc and subduction zone. The Drummond Basin sequence has been s,ibdivided into three tectono-sedirnentary cycles. Cycle I forms the base of the sequence and comprises thick sequences of intermediate to felsic volcanics and proximal volcanolithic sediments. The volcanics, particularly in the northeast of the basin, occur in separate sub-basins around what were probably isolated eruptive centres. In contrast, the rocks of Cycle 2 and Cycle 3 have been deposited during episodes of broad, basin wide subsidence. Five major igneous episodes, some of which may be co-magmatic, are recorded in the eastern Drummond Basin and environs between the Late Devonian and the Early Permian. The first and second episodes occurred during the Late Devonian to Early Carboniferous and are represented by the volcanics in Cycle 1 and Cycle 3. The third episode involves the intrusion of granitoids of Early Carboniferous age into the Drummond Basin sequence. These occur in the Ukalunda area and are related to gold mineralisation at Ukalunda and Valhalla. Episode four includes the felsic volcanics of the Bulgonunna Volcanics. This episode does not appear to he broadly auriferous but gold mineralisation does occur in possible basal Bulgonunna Volcanics at Mount Coolon. The final episode includes a suite of granitic intrusives which intrude the Bulgonunna Volcanics and which are considered to be co-magmatic with them. These intrusives do not appear to be generally associated with gold mineralisation. Gold mineralisation is widespread in the north- eastern Drummond Basin and environs. It is probable that the gold mineralisation is concentrated in epithermal cells during the Late Devonian to Early Carboniferous volcanic cycles. This style of mineralisation appears to be related to tectonic setting in modern analogues.

Jan 1, 1989