Search Documents

By L. A. Tarshis, H. E. Cline

A stability criterion for a lamellar eutectic interface was derived previously1 assuming that the wavelength, A,. of the perturbation which grows most rapidly is much larger than the lamellar spacing. A. This assumption was required to permit averaging of both the interface temperature and composition over the complicated geometry of a lamellae. If this assumption is invalid, as has been suggested.2,3 then the problem becomes too complicated to solve completely. The first of these analyses1 did not calculate the wavelength. A,. of the initially unstable perturbation. whereas the more recent analysis.' which led to a contradiction of this assumption. did not include one of the key factors for determining this wavelength. To rigorously determine the wavelength, the effect of the curvature of the perturbed interface (not considered by either of the above treatments) must be included. By omitting this term, one would be led to an incorrect conclusion regarding the magnitude of A,. but to an accurate criterion for stability as evidenced by the excellent agreement with experimental observations.' In the case of single-phase alloys. the critical wavelength. A,. for instability can be calculated from the Mullins and Sekerka4 (M.S.) analysis which includes the effects of capillarity. In the following discussion, the M.S. analysis is applied to lamellar eutectics and the critical wavelengths calculated for reasonable growth conditions in Pb-Sn eutectic alloys. In order to apply the M.S. analysis to eutectics. one may substitute i) the effective liquidus slope.1 m*. for the single-phase liquidus slope and ii) the ratio of the bulk alloy composition. C,. to the average interface composition in the liquid (Ci = CE where CE is the equilibrium eutectic composition) for the distribution coefficient to give:

Jan 1, 1970

By R. F. W. Pease, R. A. Ploc

A scanning electron microscope with a resolving power better then 100Å has been developed for the direct examination of surfaces. This instrument was used to study iron undergoing oxidation at 500°C. It was found that the electron current in the scanning electron microscope was low enough (about 10-atrzp) to have no observable effect on the growth of the oxide. "Armco " iron, when oxidized, exhibited an oxide film whose thickness and whiskey population varied with pain orientation; but purer iron, when oxidized, exhibited no such pain dependence and whisker occurrence appeared to be caused by impurities. UNTIL recently most surfaces of opaque specimens could either be studied with a light microscope or, if higher resolution was required, by viewing a replica of the surface in a transmission electron microscope. Direct electron microscopy of a surface has, in general, proved difficult owing to excessive foreshortening and the poor image quality obtained. The scanning electron microscope, however, offers an alternative method of directly viewing a surface without these disadvantages. At low magnification it offers a much larger depth of focus than the light microscope, and at high magnifications it offers much higher resolution (about 100Å). PRINCIPLE OF THE SCANNING ELECTRON MICROSCOPE A schematic diagram is shown in Fig. 1. The electron optical system consists of a gun followed by a series of lenses which focus the electron beam onto the surface of the specimen. The beam is scanned in a rectangular raster across the specimen surface and, by amplifying the secondary electron current from the 'pecimen, a picture of the specimen surface is built UP sequentially on the face of the display cathode-ray tube. The magnification of such a system is given by the ratio of the scan amplitude on the display cathode-ray tube to

Jan 1, 1965

By John Russell

"Faster, safer, grinding mill relining offers the obvious attractions of reduced mill relining times with the knock-on incentive to reduce all other maintenance down-time, opening the possibility for increased annual plant utilisation.Leading edge liner handler technologies by RME, focused toward even shorter relines for very large SAG and AG mills, have recently split into two quite distinct paths:•,?Single SAG/AG Mill Relining Machines (MRM’s) of very large capacity, such as Newcrest Cadia’s 40’ SAG MRM of 6000 kg capacity and P.T. Freeport’s 38’/34’ SAG MRM of 7250 kg capacity;•,?Twin-machine SAG/AG Mill Relining Systems of moderate to large capacity such as BHP Billiton’s Escondida Laguna Seca 38’ SAG MRM’s, each featuring 4500 kg capacity.RME, its customers noted above and their liner suppliers are providing leadership in this important annual utilisation advance.Once the 24 hour mill shell reline becomes reality, liners designed for maximum profit, not maximum life, albeit exchanged more frequently, become possible too.INTRODUCTIONAt most mineral grinding plants, mill relining activities dictate each maintenance shutdown’s critical path. When annualized, mill relining remains the largest, single influence in defining plant availability.Because of restricted access, both inside and outside the mill, increased application of manual labour has no effect on reducing relining downtime. The only answer for RME has been to develop and apply new relining technologies now known as RME’s Mill Relining System.RME’s primary focus for over twenty years has been the reduction of grinding mill relining times while simultaneously providing a marked improvement in relining safety. Our original (1990) target was to halve traditional (pre-RME) reline times and to eliminate accidents and injury by mechanizing all physical work."

Jan 1, 2008

By Antoine Fournier, Karen St. Seymour

"Responding to market developments, interest in locating deposits of wollastonite has grown significantly. The many occurrences in the Grenville marbles of Quebec can be grouped into disseminated type and discordant vein-type deposits. Disseminated-type wollastonite occurrences have the disadvantages of lower grade, the need for more elaborate mineral separation, and failure to meet ""long grain"" technical specifications. Vein-type deposits have better grades and technical characteristics; exploration should be focussed on these and in the contact-metamorphic aureoles of fluid-rich intrusions. SOMMAIREEn réactions aux nouveaux de bouches, l'interet pour les gîtes de wollastonite a crû de façon marquée. Les nombreux indices sis dans la province de Grenville au Québec peuvent être regroupes en deux catégories soit: les indices dissémines et les indices en veines discordantes. Les indices dissémines ont le désavantage d'être moins enrichis, de requérir une séparation minéralogique plus complexe, et leur wollastonite ne possède pas le degré d'acicularité voulu. Les indices en veines sont plus enrichis en plus de rencontrer les critêres techniques; les efforts d'exploration devraient se porter vers ce type de gites et aussi, sur les auréoles métamorphiques de contact d’intrusions riches en fluides."

Jan 1, 1992

By Hamish D. S. Miller

Currently the underground potash mines in Canada extract about 40% of the available ore, leaving the other 60% behind in the form of stabilizing pillars. The presence of water in the overlying formations requires that any disturbance due to mining be such that no water will enter the workings. This paper deals with the factors that influence the stability of the rock surrounding the mine excavations and looks at the effects of these factors when a system of increasing the extraction is considered.

Jan 1, 1983

By W. P. Channon, J. B. See

The reduction of fluxed and non-fluxed manganese, ores by ferromanganese silicide by W. P. CHANNON, B.Se. (Eng.), M.Sce. (Eng.) Wits. (Visitor) and J. B. SEE, B.Sce. Hons., Ph.D. (New South Wales), M.I.M., M.I.M.M. (Member) In South Africa, medium-carbonferromanganese is produced by the silicothermic reduction of slags containing MnO. Because of its importance in the production of refined ferromanganese, a study was made of the reaction between a premelted South African Mamatwan manganese ore and various ferromanganese silicide reducing alloys, with and without fluxing agents. Because the reaction is highly exothermic, temperature appeared to have little effect on the rates of manganese transfer to the metal and silicon transfer to the slag, and an apparent equilibrium was rapidly approached. Limits were determined for the favourable effects of fluxing additions, and manganese recoveries were found to decline as the ratio of CaO to MgO decreased as a result of the addition of basic flux. The recovery of manganese passed through a maximum, and subsequently decreased for variations in the ratio of alloy to ore. The results obtained, when used in conjunction with other physicochemical data related to this slag-metal system, suggest optimum slag compositions for the efficient manufacture of medium-carbon ferromanganese from Mamatwan ore.

Jan 3, 1977

Gold Fields Ghana Ltd (GF Ghana) currently operates an underground mine at Tarkwa, in south--west Ghana. The mine was operated by Tarkwa Goldfields Limited, a wholly owned subsidiary of the State Gold Mining Corporation of Ghana (SGMC). The mine was making operating losses and in a poor state of repair. Tarkwa Goldfields retrenched all the staff and GF Ghana assumed management responsibility for its own account on I July 1993.

Jan 1, 1997

By Wm. R. Webster

THIS is a contribution for the proposed new discussion on the physics of steel. The former discussion on the subject started with the consideration of five papers presented at the Chicago meeting in 1893, and continued for several years. The Suggested Lines of Discussion, prepared by Doctor Howe, covered a wide field and added greatly to the success of the work. Naturally, the first step in a new discussion will be to remodel and bring up to date the old Suggested Lines of Discussion so as to embody all the important advances in the metallurgy of steel that have a bearing on the physics of steel and keep the papers and discussions within the field of work undertaken. This paper will be devoted to the practical application, in rolling steel, of the effects of carbon, phosphorus, and manganese on its tensile strength, with some suggestions on further research work. Dr. J. E. Stead, in his paper Influence of Some Elements on the Mechanical Properties of Steel,1 gave a complete review of all that had been done during the past thirty years. He gave full credit to all investigators who worked on these lines, also their results, with his views on same, and in many cases his own results. All of this data and much new valuable information were put in convenient shape for reference and study. To do this required a great deal of work, which is fully appreciated by the steel manufacturers and investigators. The variations in the values given by the different investigators for the increase of the tensile strength of steel for each 0.01 per cent. of carbon, phosphorus, and manganese were largely due to the steels they worked on, the large or small variations in the amount of the elements present, and the omission to take into consideration all the factors, from the blast furnace through to finished rolled material, that affect the character of the steel. For instance, a poorly made dirty steel requires considerably more carbon to give the same ultimate strength than a well-made clean steel with the same phosphorus and manganese content.

Jan 3, 1921

By G. V. Smith, R. F. Mehl

The decomposition of austenite in steels, because of its immerse practical importance, has been subjected to extensive study in recent years from the point of view of the mechanism of the process.1"3 Although much information has been acquired, a number of questions, principally of theoretical interest, remain. One is that of the atomic-crystallographic mechanism by which each of the various reaction products forms. The isothermal reaction products of the eutectoid decomposition in plain carbon steels (to which this study is restricted) have conveniently been classified in three general groupings—pearlite, bainite, and martensite. Of these several products, pearlite and martensite have been studied extensively, but bainite has received only scant attention. -As a result, the mechanism of the formation of pearlite and that of martensite are now fairly well understood while a great deal of uncertainty exists regarding bainite. Pearlite Pearlite forms from austenite by the precipitation of alternate platelets of cementite and ferrite, which grow into the austenite matrix.2--5 The rate of reaction may be described in terms of a rate of nucleation and a rate of growth.2.3 Mehl and Smith6 have attempted to determine the lattice relationships existing between the ferrite in pearlite and the' parent austenite. Using a pole-figure method of analysis, it was found that a limited number of ferrite orientations resulted from the decomposition of a single grain of austenite; it was not possible, however, to decide between two assumed ideal relationships, both of which appeared to account for the experimentally determined pole figure. It was definitely shown, however, that the relationship obtaining was quite different from that determined for the proeutectoid separation of ferrite.7 No attempt was made to determine the habit plane (matrix plane to which the precipitate lies parallel) of the pearlite lamellae. Belaiew8 earlier had stated that the number of directions assumed by the pearlite lamellae in a single grain of austenite was 12 (no details were given) and concluded wrong!:!, as Mehl and Smith6 have pointed out, that the lamellae delineate the {2I0} planes of ferrite.* Martensite It is known that martensite is a transiti0nal constituent of body-centered tetragonal lattice,' and that it forms suddenly

Jan 1, 1942

By R. F. Mehl, G. V. Smith

The decomposition of austenite in steels, because of its immerse practical importance, has been subjected to extensive study in recent years from the point of view of the mechanism of the process.1"3 Although much information has been acquired, a number of questions, principally of theoretical interest, remain. One is that of the atomic-crystallographic mechanism by which each of the various reaction products forms. The isothermal reaction products of the eutectoid decomposition in plain carbon steels (to which this study is restricted) have conveniently been classified in three general groupings—pearlite, bainite, and martensite. Of these several products, pearlite and martensite have been studied extensively, but bainite has received only scant attention. -As a result, the mechanism of the formation of pearlite and that of martensite are now fairly well understood while a great deal of uncertainty exists regarding bainite. Pearlite Pearlite forms from austenite by the precipitation of alternate platelets of cementite and ferrite, which grow into the austenite matrix.2--5 The rate of reaction may be described in terms of a rate of nucleation and a rate of growth.2.3 Mehl and Smith6 have attempted to determine the lattice relationships existing between the ferrite in pearlite and the' parent austenite. Using a pole-figure method of analysis, it was found that a limited number of ferrite orientations resulted from the decomposition of a single grain of austenite; it was not possible, however, to decide between two assumed ideal relationships, both of which appeared to account for the experimentally determined pole figure. It was definitely shown, however, that the relationship obtaining was quite different from that determined for the proeutectoid separation of ferrite.7 No attempt was made to determine the habit plane (matrix plane to which the precipitate lies parallel) of the pearlite lamellae. Belaiew8 earlier had stated that the number of directions assumed by the pearlite lamellae in a single grain of austenite was 12 (no details were given) and concluded wrong!:!, as Mehl and Smith6 have pointed out, that the lamellae delineate the {2I0} planes of ferrite.* Martensite It is known that martensite is a transiti0nal constituent of body-centered tetragonal lattice,' and that it forms suddenly

Jan 1, 1942

By Liu Wei-feng

In this paper, the practice of separating precious metals from base metals in gold-antimony alloy by selective chlorination leaching under controlling potential in China has been introduced in detail. The precious metals and the base metals can be separated completely when the complex gold-antimony alloy is treated by this process. The impurity metals were removed effectively since the leaching efficiencies of copper, nickel and antimony are over 99%, with direct recovery of gold being 99.83% that is about 20% higher than that of the original process and silver, antimony, copper and nickel are also recovered effectively. The gold grade of the resulting crude gold powder can reach to 94%.The new process has been applied in the treatment of gold-antimony alloy for two years, and many former procedures have been cancelled, such as electrolysis, Anode slime leaching by nitric acid, smelting in crucible and blowing in muffle. The new process is more shorten, lower cost and friendly to the circumstance comparing to the original process.

Jan 1, 2008

By P. Somasundaran

Electrochemical properties of silicate minerals govern their behavior in processes such as flocculation and enhanced oil recovery that can occur at elevated temperatures. Knowledge of these properties as a function of temperature can be helpful in developing an under- standing of the role of these interfacial properties at non-ambient temperatures. Zeta potential of Sodium Kaolinite and quartz has been determined as a function of pH and temperature in this work. Both systems exhibited markedly different behavior at higher temperatures and also exhibited significant hysteresis. Results are examined in terms of possible dissolution of the minerals and surface reactions at different temperatures.

Jan 1, 1986

By Chitombo GP

The proposed guidelines on vibration limits that have been circulated by the Australian Environmental Council, demonstrate the need for an extensive data collection and evaluation program to avoid the enacting of abritrary and costly legislation. The operational or practical influence of blast design and overall economic implications of legislation which further reduces permissible levels of ground vibration are discussed. In a typical blasting operation, blast sizes could become smaller and blasting correspondingly more frequent to meet pro- duction demands. Blasthole diameters and charge lengths could be reduced, increasing drilling costs and associated labour costs. Blast size however, is frequently controlled by factors associated with machinery, grade control, pit control, stope size, production contract levels and other factors which cannot be readily changed for operating mines. Blasthole diameters are frequently deter- mined by existing drilling equipment, length of holes (depth of ore or stope size), geological structure and other factors which are not easily changeable. Typical large scale open stoping and strip mining opera- tions are analysed as case studies. The effects of extreme leg- islative limits and the corresponding operational changes with respect to variations in production costs are discussed.

Jan 1, 1987

By M. G. B. Wheeler

SYNOPSIS This report outlines the development of a model to simulate the radiometric sorting of gold- and uranium-bearing ores. The developed program indicates the optimum mass, reject percentage, and expected reject gold and uranium grades for a radiometric sorter. It achieves this by statistical analysis of the data gathered from a large sample of rocks in the required size range for a particular mine. The program can be used in the optimization of existing sorters, as a design tool for new radiometric sorters, and in feasibility studies on radiometric sorting.

Jan 1, 1989

By David del Pino Ávila

El incremento de los costos de tareas, materiales, repuestos y la contínua baja del precio de los metales, conllevó que los ingenieros a cargo de las operaciones en la mina Carahuacra, mejoren sus métodos de minado y reduzcan sus costos, aumentando la productividad, así como las leyes de mineral de zinc mediante una mejor selectividad de los block a minar. En este sentido, el presente texto busca mostrar las actuales operaciones unitarias de perforación, voladura, sostenimiento robotizado, limpieza, acarreo del mineral y relleno de las áreas vacías, en tajeos explotados por el método súper bresting, con anchos de labor de 10 metros, alturas de 6 metros y longitudes de 200 metros. De forma que la automatización en el sostenimiento de las grandes áreas abiertas permite aumentar la eficiencia y productividad bajando costos, así como la selectividad con el objetivo que la mina sea rentable y segura.

Sep 14, 2009

The 88th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at Kelvin House, Johannesburg, on Wednesday, 14th August, 1985. Mr J.D. Austin (President) was in the chair and declared the meeting open at 16h00.

Jan 1, 1985

By George D. Drechsler

The purpose of this review is to provide an analysis of the supply and demand for coal in Europe in 1955-56 and estimates of future growth in European requirements as a medium for appraisal of the effects and benefits to the economy of the United States. This review stems from observations and evaluations made in contacts with Government and industry representatives of the principal countries of Europe and is based on detailed data selected from the established flow of unclassified economic and statistical material originating in overseas areas for use and deposit in the Bureau of Mines, Foreign Solid Fuels Section. This material includes current reports and analyses prepared by the United States Foreign Service, official reports of individual countries, foreign industry and trade publications, and the committees of the several European organizations engaged in continuing review and study of problems relating to fuels and energy. The review is presented in four sections: 1. Discussion of the more important factors relating to the present and future fuels and energy position of Western Europe.

Jan 1, 1957

By Zenjiro Asaki, Teruo Tanabe

"To clarify the formation of light rare earth (R =Ce, Pr, Nd or Sm) -Fe compounds in the reduction-diffusion (RD) process, two kinds of experiments were carried out: (a) RD experiment in which briquettes composed of R oxide powder, Fe (particles or wire) and CaH2 were reacted, and (b) immersion experiment, where an Fe plate was immersed into R-Fe melt having the composition of Fe-side liquidus line in Fe crucible. The compound formation was examined by using XRD, SEM and EPMA. The formation rates of RzFe17 measured by the RD experiment were compared with those obtained by the immersion experiment. The growth rates of compounds obtained in the RD experiment for Pr-Fe and Nd-Fe systems were much lower than those obtained in the immersion experiment. This result was explained by the difference of the reduction rates of R oxides by Ca. The parabolic rate constants for the formation of RzFe17 were separated in two groups of (a) Pr-Fe and Nd-Fe systems and (b) Ce-Fe and Sm-Fe systems. This was discussed in connection with the difference of their crystal structures and the driving force of diffusion. The parabolic rate constants for the formation of compounds in Ce-Fe and Sm-Fe systems decreased in the order of RFez, RFe3 and RzFe17.IntroductionTo understand reaction behaviors in the production of rare earth (R) -iron intermetallic compounds, which have excellent magnetic properties, is very important from engineering point of view. And the reduction-diffusion (RD) process<O has recently attracted attention as one of the promising processes to economically produce R-related materials. A few fundamental studies on the compounds formation in the RD process have previously been reported. Qi, Hino and Yazawa(2) observed the formation of R(Nd, Sm)-Fe and R-Co compounds in the process from various view points. Song and Ogawa(3) measured the growth rates of Nd-Fe and Sm-Fe compounds by using Nd or Sm vapor supplied from Nd-Ca or Sm-Ca melts. The authors have also carried out fundamental studies (4)-(8) to clarify the rate and mechanism in the production of R-Fe intermetallic compounds."

Jan 1, 1998

By G D. Carman

White Rock is a reduced tungsten-tin skarn deposit near Rye Park, New South Wales. This abstract summarises the depositÆs mining and exploration history, and current exploration by Paradigm Metals Ltd targeting an economic resource at the deposit. An&nbsp;EXTENDED ABSTRACT&nbsp;is available for download. A full-length paper was not&nbsp;prepared for this presentation.

Jan 1, 2008

By D. R. Hardman

Coal mining has been practised in South Africa for over one hundred years. The total production increased gradually in the early pat of the twentieth century, but over the past twenty years the rate of growth has been considerable. Although opencast mining has contributed largely to this increase in production in recent years, underground bordand- pillar operations still contribute slightly less than 50 per cent of the total production. The paper highlights problems arising from old bord-and-pillar workings, and an indication is given of how some of the problems have been addressed.

Jan 1, 1990