Search Documents

Narrow vein mining, with enough challenge and also where the cutting edge technology can be applied, is still a very important and exciting portion of the mining industry. Based on the deposit characteristics, the most flexible mining method, cut and fill, has been being tested mining this high grade Northern Nevada property, Hollister, since the year of 2008. In the last three years, 254,000 tons of ore were hauled out of the portal and 23,000 feet of development were excavated underground with the winning of several safety and environmental awards. Together with mine geology, the essential segments include mining cycle, ground control, ventilation, grade control and backfill method in cut and fill stopes were covered in this paper.

Jan 1, 2012

By S. K. Sharma, D. A. Stanley

The US Bureau of Mines is investigating the fundamentals of the flocculation process. The objective of this study was to determine the effects of various physico-chemical parameters, namely, shear rate, polymer dosage, and polymer concentration, on floc growth and to determine the applicability of a model for predicting polymer flocculation behavior. A rapid in-line particle size analyzer was used to follow the progress of both the floc growth and the breakage as a function of time. A genetic algorithm (GA) was used to determine the unknown parameters in the model and to fit a curve to the experimental data. The results showed that the model reproduces the experimental data with only reasonable accuracy and that it was relatively insensitive to the parameters. Results of the flocculation study showed that increases in the polymer dosage had a greater effect on the time required to reach the maximum floc size than on the floc size itself: It was also determined that, given all the above parameters, the degree of slurry mixing during the flocculation process had the greatest bearing on floc growth.

Jan 1, 1995

By Irwin R. Higgins, Joseph C. Milbourne

The selection of a suitable nitrate removal process depends on a variety of site-specific chemical and environmental issues. The dominant technologies for nitrate removal include biological denitrification and continuous countercurrent ion exchange. The decision to apply either of these technologies, or both together, depends on the nature of the waste water to be treated. Factors that affect the selection of the biological system include the feed composition and feed temperature. Ion exchange nitrate removal systems ere less sensitive to the feed composition but require disposal or destruction of the concentrated pregnant eluate. The paper discusses Tetra's continuous countercurrent ion exchange technology (CCIX™) and fixed film biological reactor, Denite®. The treatment of the ion exchange pregnant eluant is also discussed.

Jan 1, 1995

By Roger N. Dokken

It is well-known1-4 that Fe-Si alloys from approximately 9 to 27 at. pct Si show an ordered structure of the Fe3Si type at room temperature. Recently Meinhardt and Krisement,' through an investigation of Fe-Si alloys at room temperature by neutron diffraction, discovered that at 10.8 at. pct Si ordering of the FeSi type occurs while above this composition the normal Fe3Si-type superstructure appears. This FeSi type of ordering was also found by Davies8 as indicated by X-ray diffraction measurements on an Fe-8.7 at. pct Si alloy. Meinhardt and Krisement7 extended their neutron-diffraction work and determined the phase-boundary temperatures for both FeSi- and Fe3Si-type ordering. Ordering phenomena can also be studied by resistance measurements.4,8-11 Krivoglas and Maty-sina" carried out a theoretical development of the

Jan 1, 1965

By Leo P. Tarasov

Magnetic torque studies of ferromagnetic single crystals have been carried out in a number of laboratories during the last decade&apos;s2 and some work has been reported on polycrystalline material showing preferred orientation. Goss3 used the method extensively in developing electrical sheet with desirable magnetic properties, but he used it as a control rather than as a means of studying the texture. Bozorth4 made a quantitative correlation of a torque curve he obtained from some cold-rolled iron with the texture as determined from X-rays, but did not extend his studies beyond the one specimen. Other studies, which have been reported from time to time2,5 have also been incomplete in the sense that no effort was made to study a whole series of samples, differing only in degree of cold reduction or in the annealing temperature, in order to ascertain the effect of such treatments on the texture as revealed by torque measurements. It is the purpose of this investigation to make such a study, mainly in order to see how useful the method can be made when used under favorable circumstances and to find what kind of a correlation can be expected between magnetic and X-ray studies of texture. Before proceeding further, it is desirable to say a little about single crystals, so as to make clear the concepts involved in magnetic torque measurements. Magnetic Torque Method It is fairly well known nowadays that single crystals of ferromagnetic substances have directions of easy magnetization and of hard magnetization. In Fig. 1 are reproduced typical magnetization curves for a single crystal of iron, which show that in a < 100 > direction saturation occurs at low fields compared to those required to saturate the same crystal in a <110> or a <111> direction. (The magnetization intensity I is defined by the equation B = H + 4pI.) At fields high enough to

Jan 1, 1939

By Leo P. Tarasov

Magnetic torque studies of ferromagnetic single crystals have been carried out in a number of laboratories during the last decade&apos;s2 and some work has been reported on polycrystalline material showing preferred orientation. Goss3 used the method extensively in developing electrical sheet with desirable magnetic properties, but he used it as a control rather than as a means of studying the texture. Bozorth4 made a quantitative correlation of a torque curve he obtained from some cold-rolled iron with the texture as determined from X-rays, but did not extend his studies beyond the one specimen. Other studies, which have been reported from time to time2,5 have also been incomplete in the sense that no effort was made to study a whole series of samples, differing only in degree of cold reduction or in the annealing temperature, in order to ascertain the effect of such treatments on the texture as revealed by torque measurements. It is the purpose of this investigation to make such a study, mainly in order to see how useful the method can be made when used under favorable circumstances and to find what kind of a correlation can be expected between magnetic and X-ray studies of texture. Before proceeding further, it is desirable to say a little about single crystals, so as to make clear the concepts involved in magnetic torque measurements. Magnetic Torque Method It is fairly well known nowadays that single crystals of ferromagnetic substances have directions of easy magnetization and of hard magnetization. In Fig. 1 are reproduced typical magnetization curves for a single crystal of iron, which show that in a < 100 > direction saturation occurs at low fields compared to those required to saturate the same crystal in a <110> or a <111> direction. (The magnetization intensity I is defined by the equation B = H + 4pI.) At fields high enough to

Jan 1, 1939

By Alan Alhadeff

Why is mediation being hailed as the wave of the future? The high cost of putting on a trial, over-crowded court calendars and long trial delays have resulted in what prominent attorneys and leading jurists are calling a litigation crisis. In no segment of the legal world are these pressures greater felt than in the trial of the serious construction case. Furthermore, the siege mentality of both the plaintiff and defense bar often leads to a reluctance by either side to make the first reasonable offer for fear of showing weakness. Attorneys operating in the serious construction case arena express concerns that there exist insufficient opportunities for the parties to meet, tell their stories, and negotiate settlement prior to the eve of trial. Mediation, by opening lines of effective communication and encouraging meaningful settlement negotiation, has proven to be a very effective antidote to the litigation crisis.

Jan 1, 1990

By Jas. E. Thomson

"The Kirkland Lake-Larder Lake gold area is in northeastern Ontario and is a continuation of the ore-bearing belt that extends across northwestern Quebec through the Rouyn, Cadillac, Malartic, and Bourlamaque areas. It is the oldest mining camp along this famous mineral belt. Gold discoveries were first made at Larder Lake and Swastika in 1906, but it was not until 1913 that important developments at Kirkland Lake created a real interest in the country. Total gold production of the camp passed the million dollar a year mark in 1920 and increased in amount yearly until the advent of the second World War when there was a falling off due to labour shortage. The Kirkland-Larder camp ranks as the second largest gold producing area ' in Ontario. To the end of 1944, twenty-two mines in the area had produced bullion valued at $515,631,428 and ten mines had distributed dividends amounting to $205,981,116. The average grade of the ore milled in this period has been $15.17 a ton for the mines in the Kirkland Lake area and $6.49 a ton for the mines at Larder Lake.ROCK FORMATIONS OF THE AREAIn a general way the rocks of the country may be divided into the lithological groups indicated on the accompanying geological sketch map. This map has been compiled largely from recently issued geological sheets of the Geological Branch of the Ontario Department of Minest. Owing to the present difficulty of separating the formations of the Larder Lake country into the twofold age divisions of Keewatin and Timiskaming, the usual custom in the past, a lithological grouping of formations has been adopted. The age terms 'Keewatin and 'Timiskaming' are loosely used in this article to express the often used but not necessarily accurate distinction between the main groups of older strata."

Jan 1, 1954

By Hefter G. T, Singh P

The use of sulphur dioxide (SO2) as an anode depolarizer in place of traditional oxygen evolution reduces the energy costs of copper electrowinning. This paper reports the effect of various metal ion impurities, which are usually present in th

Jan 1, 1998

By A. G. Guy

Zinc vapor from a reservoir of liquid zinc maintained at lower temperatures was diffused into sets of copper-zinc alloys at 759° and 870° C and into sets of silver-zinc alloys at 650° and 700° C. Each set of ,four copper-zinc alloys consisted of pure copper and 90/10, 80/20, and 70/30 brass. Similarly the set of silver-base alloys consisted of specimens containing 0, 7, 15, and 20 pct Zn. Natural markers at the initial surfaces of the specimens ware "trapped" under a thin electroplate and their depth of burying was measured after diffusion. The ratio of diffusivities of the two components determined from these data and the chemical diffusion coefficient calculated by the Matano method agreed with previously reported results. The line of markers was irregular and was often discontinuous when a grain boundary was crossed. TECHNIQUES involving the vapor phase have been widely employed in studying diffusion phenomena in metals. Many investigators have evaporated the more volatile component from an alloy, but it is generally believed that the porosity created under these conditions interferes with adequate interpretation of the experimental results. The extensive work of Gertsriken6 has been criticized on this score. Accary1 found that the diffusion coefficient for de-zincification of brass is larger by a factor of five than that for zincification, although he attributed the difference to a higher vacancy concentration under conditions of dezincification. Balluffi and siegle2 thoroughly investigated the technique of adding a more volatile component to a less volatile base metal as a means for studying diffusion. They verified that no porosity forms in a brass under these conditions and that the diffusivities of the two components can be determined from observations of the motion of markers originally placed on the surface of the specimen. The mathematical analysis that they developed for treating the experimental data was modified in a later note, but essentially it involved using the graphical Boltzmann-Matano method that is customarily applied to solid-solid diffusion couples. The experimental method used in the present research was similar to that employed by Balluffi and Siegle except for two modifications. Balluffi and Siegle used alloy chips as the source of metal vapor. This procedure has the disadvantage that the concentration of solute at the surface of the specimen changes during the diffusion experiment as the alloy content of the chips is gradually decreased. This disadvantage was overcome by employing liquid zinc as the source of zinc vapor in a manner similar to that described by Herasymenko.9 There was then no limitation on the amount of solute usefully available, and several relatively large specimens could be diffused in a given experiment. The second modification was the use of natural markers on the surface of the specimen rather than larger, artificial markers, such as the alumina powder employed by Balluffi and Siegle. It was expected that the fine, natural markers would permit more precise measurement of the buried interface as in the case of ordinary sandwich specimens.10 EXPERIMENTAL The experiments were designed so that zinc from the vapor phase would maintain a constant zinc content at the surface of pure copper (or silver) and

Jan 1, 1960

By S. P. Liebenberg

During the past fifteen years significant progress has been made on carbon-in-pulp (CIP) technology for the extraction of gold. While most research on the mechanisms and kinetics of CIP sub-processes has focused on the adsorption step only, auxiliary unit operations such as elution have received less attention. The mathematical models which have been developed for elution at the University of Stellenbosch can be used for design as well as process optimisation by incorporation into an overall CIP simulation program. Except for these models, no other comprehensive models for the complex elution process are available. It is the aim of this paper to review recent modelling work on competitive elution from activated carbon.

Jan 1, 1995

The Racecourse Orebodies at Mount Isa consist of a series of parallel steeply dipping lead/zinc/silver orebodies with a strike length of up to 1000 metres. Production from these orebodies between 13 Level to 9 Level has been by a series of cut and fill stopes in two level stages, leaving a crown pillar at 11 level. Development of the 15 level to 13 level extraction stage has recently been completed. The layout consists of a series of parallel stopes over a strike length of 1200 metres. Access to the stopes is by two declines connecting the stopes with a series of crosscuts This paper describes the basic layout with development and production methods employed.

Jan 1, 1977

By J. Parker

Gentlemen; Rainy day in Upper Michigan, a good time to catch up on reading. Am doing that, and have a couple of questions concerning the K and P paper on roof problems and supports. I wonder if the authors can enlighten me. The compressive strength of the coal was reported as 4.4 MPa (633 psi) and compressive stresses measured in the coal seam were reported at around 27.6 and 48.2 MPa (4000 and 7000 psi ). Can such a soft coal actually contain such a high level of stress? Can it be measured as if the material were elastic, or does the coal behave plastically? Can that stress level be confirmed with hydraulic load cells? And if the coal is so soft, and if it is plastic, why is the stress field not hydrostatic? The intact roofrock appears to be unusually strong, with compressive strength reported at around 145 MPa (21,000 psi), and some failures were noted as soon as the rock was exposed. Were tests run to find out how that rock responded to the addition

Jan 1, 1991

By Bengt Fellenius

The conventional wave equation analysis without control of the representativeness of the parameters to the actual conditions does not provide accurate results. However, the representatives can be vastly improved by means of using the results of monitoring the dynamic response in a pile during driving. Dynamic monitoring displays the interaction of independent strain and acceleration measurements having directly propor­tional response to impacts, but inversely proportional response to re­flections from the soil. Examples are given and the CAPWAP method used to calculate from the measurements the dynamic pile and soil para­meters and mobilized soil resistance is outlined. The dynamic monitoring technique and analysis has been accepted internationally and been incor­porated into Building Codes. The prediction is offered that in five year&apos;s time, no major piling project will be undertaken without dynamic monitoring and analysis.

Jan 1, 1984

By W. S. Hyler, W. L. Bruckart

The powder metallurgy and arc-cast types of wrought molybdenum stock were studied in rotating beam fatigue. Endurance ratios of unnotched specimens after 5x10 cycles were found to be 0.74 and 0.81, respectively. Fatigue notch factors (K,) of 1.36 and 2.05, respectively, were obtained on V-notched specimens having a theoretical stress-concentration factor Kt = 3.1. MOLYBDENUM and its alloys are rapidly gaining importance as engineering materials of construction for high temperature applications. AS a wrought material, molybdenum and its alloys are outstanding above 1800°F. It is necessary, however, with molybdenum to provide elevated temperature oxidation protection. This is currently being studied by a number of investigators. Thus far, there have been no published data on the fatigue behavior of molybdenum either at room temperature or at elevated temperature. The knowledge of fatigue behavior, particularly notched fatigue behavior, becomes increasingly important as the engineering importance of a material increases, especially from the design standpoint. The work described here was directed toward determination of the notched and unnotched rotating beam fatigue characteristics of molybdenum at room temperature. Also, it was desired to learn whether any difference exists between wrought molybdenum of the powder metallurgy and the are-cast types. Fabrication History of Bar Stock For this work, bar stock was procured from Climax Molybdenum Co. (are-cast type) and from Westing-house Electric Corp. (powder metallurgy type). The processing histories of these materials are listed in Table I. The first lot of are-cast molybdenum was deoxidized by aluminum additions. The second lot was deoxidized by carbon." Both lots of the powder Microstructure A microscopic examination of these materials, as received, revealed the powder metallurgy molybdenum to be free of inclusions and to be finely fibered. On the other hand, the are-cast C molybdenum possessed numerous carbide inclusions, and the arc-cast A appeared to have coarse grained fibers. These are shown in Fig. 1. Owing to the large apparent difference in fineness of fiber between the are-cast A and the powder product and are-cast C, a check was made of the recrystallized grain sizes to determine whether these differences persisted. A series of recrystallization anneals revealed mixed grain sizes in both the are-cast A and the powder product. Variations in grain diameter of as much as 50 times were found after full recrystallization at 1200°C for 30 min. There was no distinction between the two. Arc-cast C was not checked. Room Temperature Mechanical Properties Prior to subjecting the materials to fatigue tests, room temperature mechanical properties were determined. These data, together with the tensil: strength of the notched bars, data,togetherare listed in Table tensil: There were no significant differences in the tensile strengths of the two types of molybdenum. However, the powder metallurgy material was generally more ductile and yielded at a somewhat lower stress than the arc-cast material. Tensile strengths of the notched specimens indicated a slightly greater notch strengthening effect in the are-cast C than in the powder product, lot 2. Room Temperature Fatigue Properties Sample Preparation: Specimens were prepared for use in R. R. Moore rotating beam fatigue machines. These specimens had a continuous radius test section with a minimum diameter of 0.260 in. The specimens were prepared by grinding to shape and polishing to produce a smooth unworked surface. Polishing consisted of rotating a disk in the continuous radius section on which were attached, successively, emery belts of 240, 400, and 600 grit. The specimens were slowly rotated during the operation. The belt speed was high, and rotation was such that polishing scratches were longitudinal. Unnotched Fatigue Properties: Unnotched fatigue data were obtained from a number of specimens of each of the four lots of molybdenum. The results of the tests are presented in Fig. 2. From this figure,

Jan 1, 1956

By M. E. Wadsworth, A. S. Peck

Infrared spectra disclose that oleic acid will not adsorb on the surface of pure beryl unless the mineral is first activated with HF. The adsorption of oleic acid on HF activated beryl is attributed to the hydrogen bonding of oleic acid monomers to F-surface bridging sites. These sites are formed as a result of the reaction of HF with chemisorbed water or surface hydroxyl. Characteristic infrared spectra of physically adsorbed oleic acid are correlated with flotation at different pH at temperatures of 25°C and 75°C for colloidal and -60-mesh particles. The usual mode of occurrence of the beryllium mineral beryl, Be3A12Si6O18, is in granite pegmatites as pale green, white, or yellow crystals. A dark green gem variety, emerald, may be found in the wall rock of pegmatite veins or in mica schist. The most important beryl deposits in the United States are in the Black Hills District of South Dakota, and several mountain ranges of central and west-central Utah contain potential commercial sources of this mineral. Several papers have been published concerning the flotation of beryl with different conditioning reagents. Kennedy and O&apos;Meara1 reported on the essential use of HF in the flotation of beryl from different ores. The use of calcium hypochlorite to separate HF activated beryl from feldspar after flotation with an amine collector was made by Runke.2 A report on the activation of beryl with different cations using sodium oleate collector was presented by Viswa-nathan and co-workers.3 Flotation of beryl with sulfonate collector and different activating salts was employed by Fuerstenau and Bhappu.4 The role of the surface charge or zeta potential in the flotation of beryl with different collectors and salts was also extensively investigated.5"7 Previous infrared investigations by the authors8 disclosed that the orthosilicate beryllium mineral, phenacite, reacts with oleic acid to form a chemisorbed oleate monolayer on the mineral surface. Thus, chemisorption is the effective mode of adsorption in the phenacite-oleate acid flotation system. In contrast, neither chemisorption or physical adsorption of oleic acid occur on the surface of pure beryl as evidenced in this study. Efforts were subsequently made to determine the mechanism of activation and collector adsorption for HF pretreated beryl. EXPERIMENTAL PROCEDURES Large, white, terminated crystals of beryl were obtained from Madagascar through Ward&apos;s Co., Monterey, Calif. The crystals were broken into -60-mesh fragments in a porcelain mortar. Part of this prepared material was ground to a powder with a Fisher Grinder using an agate mortar and pestle. The powder was transferred to a graduated cylinder and mixed with 500 ml of distilled water. After 5 min, the colloidal suspension was separated from the settled particles by decantation and used as a stock for infrared test determinations. Adsorption tests were performed by first transferring 20 ml of colloidal suspension to 50 ml glass centrifuge tubes. The solids were then centrifuged out and the liquid was discarded. Then, the solids were pretreated with one molar HC1 or one molar HF. After 15 min, the solids were again centrifuged out. The mineral solids were washed free of residual acid by repeated centrifuging and water washing operations. Then, 20 ml of distilled water was added to the solids, and the resultant suspension was used for test purposes. In the preparation of mineral for flotation tests, 1.5 g of -60-mesh beryl was deslimed by removing the colloidal fraction by three successive water washes and decantations. Then, the coarse particles were pretreated with either one molar HCl or one molar HF for 15 min. The mineral was next washed free of acid with distilled water, and 20 ml of distilled water was added to the beryl prior to collector conditioning. The conditioning of mineral with collector was performed in 50 ml centrifuge tubes to which either NaOH or HC1 was added for pH modification. One drop (6.0 mg) of U.S.P. reagent grade oleic acid or 2 ml of 0.01 molar sodium oleate was added to the pulp and stirred at about 1500 rpm for 3 min at a

Jan 1, 1968

By M. Paulus

It is known that multicomponent powders are mostly nonhomogeneous. This paper investigates the effects of nonhomogeneity of composition and grain size on the melting point and the sinterability of compact taking into account homogenization mass transport and the length of the diffusion path in solid state sintering, and the kinetics of liquid phase formation in liquid phase sintering. After a discussion on the ideal characteristics of a powder for sintering and low temperature reaction, the main conventional processes are compared. Finally we develop the freeze-drying technique and demonstrate the capabilities and the limits of the process by some examples, mainly in the ceramics field.

Jan 1, 1980

By Joseph E. Pogue

The past year in the petroleum industry was one of overproduction, rising inventories, low prices, and meagre to vanishing profits. This outcome was the result of a long period of intensive and uncompensated effort on the part of both financial and industrial interests, to stimulate supply on the theory that the primary problem facing the petroleum industry was the development of an adequate reserve of raw material to protect a large and ever-growing investment. The stimulus was applied in various forms and through diverse channels: capital had long flowed into the industry in excessive amounts under the attraction of large expected profits; the price level for crude petroleum had persistently been influenced by speculative considerations, with the result that prices declined slowly in periods of flush production and were quick to advance in anticipation of statistical improvement, thus maintaining a superfluous degree of stimulus on wildcatting and on drilling; speculation in inventories had led to the unsound, or at least unusual, business practice of accumulating huge stocks of oil; and, above all, the industry had directed the potent force of technology to the expansion of supply and achieved radical results in accelerating oil discovery, speeding up the rate of oil extraction, and enlarging the recovery of gasoline and lubricating oils from the raw material. In short, the economic conditions of 1927 were exactly those to which the objectively driven enterprise of the petroleum industry had long been directed; and the undesirable financial consequences arising therefrom reflected no lack of success in what had been set out to be achieved, but rather the failure to have established concurrently the necessary means of economic control to prevent the immediate conversion of reserves into current supply, and likewise the oversight in neglecting to apply the technological force to the enlargement and diversification of the market for petroleum products. Perhaps, when viewed in its longer perspective, 1927 will stand out as the turning point in the economic policy of the petroleum industry, when the technique of rationalizing production made its initial claim for recognition.

Jan 1, 1928

By J. G. Richardson, F. M. Perkins

Results and procedures are pre-cented covering a laboratory investigation of the effect of rate of water advance on the displacement of oil from clean water-wet sands. The experiments included water floods at atmospheric pressure with and without gas present over a range of flow rates from reservoir rates to rates ten thousand-fold higher. Water floods were also conducted at various rates at elevated pressure with no gas present. Other tests were made at elevated pressures by forming a free gas saturation by evolution of gas from solution in the oil before water flooding. Recovery of oil was found to be independent of the rate of water advance with or without gas present and independent of the pressure level of the water flood. A dimensionally-scaled model of a reservoir composed of a thick uniform sand was used to study the effect of rate on the tendency of water to underrun the oil because of the greater density of the water. Another model was used to study the effect of rate on the tendency of water to channel down the more permeable sand in a stratified reservoir composed of sands of diffierent per-meability in intimate contact. The effect of the presence of gas on the flooding conformance was studied with both models. The results obtained using these simple models provide a basis for predicting behavior in more complicated systems. INTRODUCTION In spite of the great amount of research on the flow of fluids in porous rocks, there still exists some disagreement as to the influence of the rate of water advance on the displacement of oil by water flooding. Various investigators have found that increasing the rate of water injection would decrease, increase, or have no effect on recovery of oil. One reason for this disagreement has been a lack of understanding of the effects of the capillary forces which influence the results obtained in the laboratory at low rates with short columns. Other causes of the disagreement have undoubtedly been inconstancy and uncertainty of the wetting properties of the porous media studied, inaccurate saturation determinations, and in some instances conclusions based on insufficient data. Capillary forces are involved in the displacement of oil by water in two ways. On the microscopic scale, the capillary forces control the dis- tribution of oil and water in the pore spaces of the sand. The magnitude of these forces is governed by the preference of the sand to be wet by water, the pore sizes and geometrical shapes, and the interfacial tension between the water and oil. On the macroscopic scale, differences in saturation at the flooding "front" when water displaces oil result in capillary pressure gradients. These gradients cause water to flow preferentially ahead of the front. In short laboratory columns at low rates, the front can span the entire column length. Also, at the outflow boundary the preference of sand to be wetted by water results in retention of water and a high water saturation in the region of the outflow face. This effect is commonly called the boundary effect.&apos; The capillary pressure gradients which complicate the interpretation of flooding performance of short laboratory columns at low rates of water advance become negligibly small under certain conditions. The conditions where capillary pressure gradients are negligible are in long, homogeneous reservoir sands,&apos; at high rates of water advance in short laboratory columns,3 and at any rate in laboratory columns as the residual oil saturation is approached. Thus, laboratory water floods, conducted

Jan 1, 1958

By Lu Fujun, Chen Xuewei

This paper will analyse the cause-effect relationship of the main factors influencing the production of the fully-mechanised coalface by mainly using the basic system dynamics theory. On the basics of the analysis, the simulated model of the sy

Jan 1, 1998