Search Documents

By D. A. Dahlstrom

THE necessity for slime elimination from valuable mineral and coal products has become increasingly significant within the past 5 years.1,2 Most of the mechanized mining and present beneficiation methods have resulted in larger tonnages of extreme fines, silts, and clay, commonly called slimes, processed by the preparation plant. Economics in turn have forced the plant operator constantly to lower the bottom size of effective beneficiation, necessitating an almost complete recovery of valuable solids regardless of particle size. When these important factors are considered, the need for an efficient slime removal method for fine solids becomes self-evident. Ordinarily slimes have been classified as ranging from 75 microns, or 200 mesh, down to colloidal dimensions of less than one micron. At the same time there is general agreement that the most troublesome slimes are primarily clays, silts and extreme fines, so that the actual top size may be placed at approximately 30 to 40 microns. This immediately restricts any desliming operation to classification, as screening or other methods would be both uneconomical and grossly inefficient at such dimensions. The liquid-solid cyclone has been recognized as one of the most efficient fine size classifiers available to the mining industry. Applications of cyclones to thickening, high efficiency solid recovery, degritting,

Jan 1, 1952

By Hsun Hu, R. S. Cline

The effect of rate of deformation on texture formatiotz has been studied with cube-oriented single crystals of 3 pct Si-Fe, compressed 80 pct at two widely different rates. Compression at a low rate (crosshead speed, 0.1 ipm) produces large orienta-tional changes and coarse deformation bands, whereas little change in orientation is observed, particularly at the surface of the crystal, when compressed at a high rate (impact velocity, -500 ips). Thin plates of mechanical twins are produced at the high rate, but their contribution to the deformation texture is practically negligible. The crystal deformed at a high rate has a lower hardness and a more uniform dislocation structure and is morc resistant to recrystallization. There is also a dilference in the recrystallization texture between the slowly and rapidly compressed crystals. These results indicate that plastic flow is less "turbulent" at high strain rates than at low strain ratcs. THE behavior of metals under high-speed deformation has been the subject of wide study in the past decade. Most of these works were concerned with mechanical properties during testing at high rates of loading, the resulting structures, and the theoretical aspects of the observed phenomena. The present status of knowledge and research activities in this field has been documented in recent publications.17' There is, however, very little information available in the literature concerning the effect of high-speed deformation on the texture formation in metals. The possibility of an effect of rate of deformation on texture is suggested by the microstructural differences observed between normally and very rapidly deformed samples. Aside from the strong tendency for twinning (and phase transformation in certain metals) in high-speed deformation, the slip-line patterns and the dislocation configurations show marked differences as a result of large differences in the strain rates. For instance, in mild steel in static and dynamic compression, Campbell and co-worker3,4 observed that coarse slip occurred on several systems in specimens deformed at normal strain rates, whereas specimens deformed rapidly showed only fine slip on fewer systems, the slip-line pattern being very similar to that in specimens deformed at low temperatures and at normal strain rates. The absence of multiple slip was also noticed by Dieter5 in shock-loaded nickel. The dislocation configuration in an iron shock loaded at 70 kbar pressure was shown by Leslie et al.6 to be similar to that produced by light rolling at low temperature—the dislocation lines were mostly straight and uniformly distributed. These observations suggest that the mode of deformation at high strain rates is notably different from that at low strain rates. Consequently, the nature and the extent of lattice reori-entation during deformation should also be different. This investigation was undertaken to test this idea. MATERIAL AND METHOD The remaining part of a single-crystal ingot of a 3 pct Si-Fe alloy,* prepared for an earlier investi- gation,1 was used in the present studies. Specimens 9/16 in. square and 0.365 in. thick were cut from this ingot with (001) planes parallel to the square surfaces, and the [loo] and 1010] directions parallel to the edges of the specimen, within ±1 deg. These machined crystals were etched to remove distorted metal, and annealed at 1300°C for 24 hr in a purified helium atmosphere. The annealed crystals had a hardness of 161 Dph. The crystal orientation was rechecked with X-ray back-reflection techniques. In high-strain rate experiments the crystal was compressed in a Dynapak machine to approximately 80 pct reduction in thickness (from 0.360 to 0.070 in. with an impact velocity of -500 ips). Thus, the duration of loading was approximately 6x 10-4 sec, and the average strain rate was about 103 sec-1. As a result of this rapid, severe deformation, the specimen became a roughly circular thin disc. The original shape of the crystal, however, could still be recognized by a diffusely outlined square area in the center of the disc. For compression at a low speed, the crystal was deformed in a universal testing machine at a rate of crosshead movement of 0.1 ipm. Compared with

Jan 1, 1965

By F. Chase, D. Pappas

Pillar recovery has been associated with nearly one third of roof fall fatalities in underground coal mines during the past decade. Safe pillar recovery requires global stability and local stability. Global stability is addressed primarily through pillar design. The local stability risk factors include cut sequence, the final pillar stump, supplemental supports (timbers vs. Mobile Roof Supports (MRS)), roof bolting, and many others. The National Institute for Occupational Safety and Health (NIOSH) has evaluated each of these factors through field research and analysis of accident statistics. The paper discusses design methods and technologies that have been transferred to the mining community and implemented.

By Fan Delian, Ye Jie, Lui Tiebing

The lower and the upper parts of the Doushantuo Fonnation, Hubei Province, China, contain silicate-type K-rich beds (illite and feldspar), and intraclastic phosphorites, as well as Ag-V and V deposits in a "Black Shale Series". The K-rich beds fonned in an anoxic basin whereas the phosphorites fonned in a more oxic and higher energy depositional environment. The Black Shale Series occurs in the lower and upper parts of the Doushantuo Fonnation; that in the upper part consists of black illite shale and dark gray dolostone, and contains Se-rich Ag and V deposits. These deposits are of more industrial significance than the previously discovered Ni-Mo polyelement sulfide deposits which occur in the Lower Cambrian Black Shales Series of South China. Studies of lithotype, sedimentary sequence, and geochemistry of the Doushantuo Fonnation have led to more attention being focused on the uppennost Black Shale Series and its Ag-V and V deposits. There are three ore types: black, Ag-V-rich, illite shale; black, V-rich, illite shale; and dark gray, Ag-Vrich, fmely crystalline dolostone. The first two ore types contain 3070 to 5% Corg and the last, 1.25%. The Ag-bearing minerals are naumannite, argyrodite, aguilarite, acanthite, and native silver that occur as inclusions in pyrite associated with barite. Vanadium substitutes for AI in illite and is also related to organic-matter contents. Because (1) the pre-Sinian Kongling Group contains one to three times greater than the Clark Ag value; (2) black, illite shale has a negative Ce anomaly; and (3) there are large occurrences of black, K-rich, tuffaceous, fme siltstone, the sources of Ag are thought to include subaerial and submarine volcanic materials. It is proposed that Ag, V, and Se were absorbed by clay particles and organic matter during syngenetic deposition in an anoxic environment; Ag subsequently was reconcentrated into sulfides and selenides, whereas V was incorporated structurally into illite during early and late diagenesis. These types of Black Shale Series-hosted Ag-V and V deposits are, therefore, considered to be sedimentary-diagenetic in origin.

Jan 1, 1992

By Larry Schneider

I n the simplest application of a shock tube initiation system, the tubing acts as a “relay line” which passes a detonation signal from borehole to borehole. When the signal arrives at each borehole, it causes the detonator attached to it to fire. Such a single path constitutes a progressive series where each unit must function properly in order to activate the following units. Any application error, malfunction, or mistake in connecting any surface unit will stop the progression of the detonation signal through the system and result in a “cutoff” or misfire of the following charges.

Jan 1, 1995

By R. B. Stroud

Bureau of Mines studies of copper-bearing Permian red beds, which extend from north-central Texas through western Oklahoma to southwestern Kansas, indicate heretofore undefined commercial possibilities for low-grade, medium-volume, strip-mining operations. Potential ore bodies are indicated containing 0.5 to 1.5 percent copper in zones 6 to 12 inches thick. Cost analysis studies indicate a commercial operation is feasible for a hypothecated 1,000-ton-per-day ore mining and milling complex where a maximum of 60 feet of overburden can be stripped in mining a seam of shale 12 inches thick containing 1.2 percent copper

Jan 1, 1970

By T. Nishimura, H. Kiyama, K. Wakimoto

Discussion on the load bearing capacity of ground and the stability of tunnel is presented. We derive a simplified solution of a circular lined-tunnel in an elastic ground. The solution results in a better understanding of characteristic curves. Use of DEM allows us to consider effects of possible yield of the overstressed zone around the tunnel and inherent discontinuity of ground on the curves. Diskussion auf der Last Tragfähigkeit Bodens und die Stabilität des Tunnels wird dargestellt. Wir leiten eine vereinfachte Lösung eines kreisförmigen Ausbautunnels in einem elastischen Boden ab. Die Lösung ergibt ein besseres Verständnis der Kennlinien. Um Gebrauch DEM erlaubt uns, zu betrachten Effekte des möglichen Ergebnisses der überbetonten Zone den Tunnel und zugehörige Unstimmigkeit des Bodens auf den Kurven. La discussion sur la portance de charge de la terre et de la stabilité du tunnel est présentée. Nous dérivons une solution simplifiée d'un revêtement-tunnel circulaire dans une terre élastique. La solution a comme conséquence une meilleure compréhension des courbes caractéristiques. L'utilisation de DEM nous permet de considérer des effets du rendement possible de la zone surchargée autour du tunnel et de la discontinuité inhérente de la terre sur les courbes.

Jan 1, 2003

By V. Enns, E. Soprovich, J. H. G. Laflamme

A mineralogical and geochemical characterization study was carried out on arsenic-bearing Ketza mine tailings to complement a column extraction test program with the purpose of assessing the potential of arsenic mobilization from the tailings. Two types of tailings samples (i.e., exposed tailings from the impoundment area and water covered tailings samples) were subjected to column tests under standing water cover and with no water cover but weekly flow-through flushing. The tailings have a uniform size distribution. The samples are characterized by high Fe2O3 (44.0 to 68.2 %) and As (3.7 to 4.4w%) concentrations. Ferric hydroxides are the dominant species that are mostly amorphous or cryptocrystalline. Arsenopyrite, scorodite, an Fe-Ca arsenate hydrate phase, an Fe-Bi-As phase and ferric hydroxides are the arsenic-bearing minerals. Arsenic is essentially contained in Ca-As goethite, Fe-Ca arsenate hydrate phase and scorodite. Goethite, although containing low levels of arsenic, could be a significant arsenic-bearing phase because of its high abundance. There does not appear to be any significant chemical or mineralogical difference between the original exposed tailings and the material left underwater with no flow-through for over a year. There are differences in terms of CaO, Fe2O3, SiO,, As, goethite, scorodite, calcite and dolomite concentrations between the exposed tailings and the column material after undergoing approximately two-year flow-through and aggressive leach tests. These differences are likely to be resulting from a combination of different column test conditions and sampling or heterogeneity of the material.

Jan 1, 1998

By M Ridd

The Pasminco Century Mine (PCML) is located 250 kilometres north-north-west of Mt Isa in Queensland. As one of the worldÆs largest zinc mines, PCML comprises mining and milling operations at Lawn Hill, concentrate filtering and shipping facilities at Karumba in the Gulf of Carpentaria, and a 304 km slurry pipeline connecting the two operations.Mineralisation at Century occurs in the upper part of the Lawn Hill formation and is comprised of siltstones, shale and sandstone. Pyrite occurs immediately above the mineralised sequence, and throughout the footwall carbonaceous shale forming the lower proportion of the deposit. Zinc predominantly occurs as sphalerite (ZnS) and lead as galena (PbS). These sulfides are very fine-grained and may oxidise rapidly upon exposure. The pyrite, sphalerite and galena are the main potential sources of acid rock drainage (ARD) or heavy metal leachate at the mine site.To minimise the generation of ARD in the waste rock dumps, they are constructed in a specific manner and waste rock is classified into the following three classes based on competence and acid forming/consuming capabilities:Class 1: Competent rock, non-acid forming or acid-consuming material. Class 2: Non-competent, non-acid forming or acid-consuming material. Class 3: Acid-forming material. The generalised Waste Rock Dump Design for current operations comprises an outer zone of Class 1 material and inner zone with Class 2 and 3 material. Limestone is the Class 1 material used for both its structural support and acid neutralising capacity. Reserves of limestone at the mine site are limited. Net acid generation (NAG) tests confirm that a mix of limestone and shales can be net acid consuming.Field based and laboratory based trials have been established at PCML to quantify blending levels of limestone and shale that will produce leachates both neutral in pH and low in metal/salt concentrations. This paper will discuss the first six months results (of a two-year sampling program) from the trials.

Jan 1, 2004

By E Emery Jr Gray

The City of Richmond, in an effort to improve sewage treatment facilities, designed an invert syphon to cross the James River at Fulton Bottom. The design criteria called for installation of two 36-inch pipe' lines at an elevation of -35 with the mean water level being at elevation 00. This paper discusses the actual method of construction used to blast the river bottom. Choice of excavation equipment, nature of the river, as well as the geological structure, were taken into consideration.

Jan 1, 1979

By Michael Amick, G. Swan, R. Hill, C. Pritchard

Falconbridge, a major base metal producer in the Sudbury Basin of Ontario, identified a need to find a safe and cost effective replacement for welded-wire mesh used to support loose ground during underground nickel mining. Falconbridge took a methodical approach to the concept of a spray-on liner as a screen replacement proving the strength characteristics of the liner as a safe, cost effective, and suitable method of supporting ground. Compact, hydraulic mixing and spraying equipment have been developed and are in use at the Fraser mine. The Tekflex material has been approved as a wire-mesh replacement and has been in use since November1998.

Jan 1, 2000

By Francis Vanbellen

Umicore Precious Metals Refining operates an integrated precious metals smelting and refining plant in Hoboken, Belgium. Once a smelter and refiner of complex concentrates, the plant today?s feed consists exclusively of industrial and consumer recycled products, making it the world?s largest recycling facility for precious metals. Unlike the fairy tale of the Frog Prince, it took much more than a princess? kiss to successfully realize this makeover. A completely renewed plant has been built over the past decade.

Jan 1, 2006

By Artak D. Mirzoyan

Pile foundations near the edge of a slope are often required to resist lateral loads. This is particularly important for piles at abutments of bridges. However, very few full-scale tests are available that compare the effect on lateral resistance of piles installed in sloping ground to piles installed in horizontal ground. To investigate the effect of a slope on lateral pile resistance, three full-scale lateral load tests were performed on an instrumented steel pipe pile. For the first test, the pile was laterally loaded in horizontal ground; in the second test, the pile was at the crest of a 30º downward slope; and for the third test, the pile was located three pile diameters from the crest of a 30º slope. The soil around the pile consisted of well-graded clean sand (concrete sand) and was compacted to 95% of the modified Proctor maximum unit weight in all three tests. Lab and in-situ direct shear tests indicated that the friction angle of the sand was approximately 39 degrees. The pile was instrumented with strain gauges so that the bending moment versus depth profile could be determined. Pile head load, deflection and rotation were also measured. Based on the load versus deflection curves, the presence of the slope resulted in a decrease in lateral resistance of about 20% for the pile at the crest of the slope and 8% for the pile at 3D from the crest of the slope relative to the pile in horizontal ground. The presence of the slope also resulted in an increase in the maximum moment of 29% and 20% for the piles at the slope crest and at 3 pile diameters from slope crest, respectively. Analyses using LPILE with the measured friction angle significantly underestimated the lateral resistance for the horizontal soil profile. After calibrating the model with the response of the pile in horizontal sand, analyses including the slope still underestimated lateral resistance by about 20%.

Jan 1, 2007

By J. M. Adams

It is my purpose to give some of the results obtained by an experience of nearly seven years in working ores by the method frequently called the Washoe Process, and in several mills of which I have had charge, but principally in the Owyhee Mill, at Silver City, Idaho, which had twenty 650-pound stamps, and sixteen pans. I shall discuss here merely the mechanical details for working ores generally, subdividing the subject as follows : 1. Preparation of the ore for the stamps; 2. The crushing in the battery; 3. The settling of sand or pulp in vats or tanks; 4. The treatment in the pans; 5. The results obtained in settlers, agitators, and concentrators; 6. The straining of quicksilver, cleaning of amalgam, and retorting; 7. The saving of slimes and their subsequent treatment; 8. The loss of quicksilver. For descriptions of the various kinds of orebreakers, stamps, tanks, pans, settlers, etc., I must refer to the various works on these subjects, prominent among which are the reports of the United States Commissioner of Mining Statistics,and the volume on "Mining Industry," the third volume of the United States Geological Survey on the Line of the Fortieth Parallel through the gold and silver bearing regions of the great West, undertaken under the able guidance of Clarence King, assisted by Mr. James D. Hague and others. In this discussion it will be assumed that the general arrangement of the quartz mill is understood; and the question will be treated how to secure, from such a mill, the greatest economy in working, combined with the largest results. This place seems fittest for a single preliminary suggestion—namely, that there should be double "floors" throughout the mill, so that nothing can sift through and be lost.

Bahuerachi Project Characteristics Why it?s nicer at Bahuerachi Mexico is a mining country Low political, regulatory and trade risk Low social/permitting risk Proximity to infrastructure Road Power grid (8 km) Rail line (25 km) High grade zones (skarns), CRD and near surface oxide component are sweet spots to the overall system. Size of low grade system points to potential long mine life?and numerous new targets developing. Timelines-2006? 90 to 100 combined RC and core holes to go! MAIN ZONE Drilling ? Goat ?Finish Mid April ? Main Zone, going North, depth of testing dependent, estimated for May ? North Lobe-May ? Commission independent resource estimate by May 06 for results of first pass drilling to date ?tonnesand grades ?Main Zone Milestone. ? Continue infill or expanded drilling to July (minimum) ? 1stpass RC scheduled until September OTHER Targets ? Begin drill testing North Skarn target Mid-April, minimum 5 drill holes, 1,000 meters. Ongoing expansion of target with surface work (mapping) ? Road to Colome(Skarnin north of Main Zone) as part of porphyry program ? Tule(southern) porphyry and skarn system-soils and mapping OUTSTANDING events Metallurgical report on floating and leaching tests (Sulphide/oxides).

May 1, 2006

By L. H. Levenson, Charles S. Barrett

Numerous determinations1-' of the texture of cold-rolled polycrystalline iron, steel, and ferritic alloys have been made with good agreement among the various observers as to the principal features of the texture common to all, but there has been no adequate explanation of the texture in terms of, the behavior of individual grains. This study presents an explanation of the texture based on the observed rotation of single crystals when deformed in a manner similar to a grain in the aggregate, a method we have found useful in leading to a better understanding of compression and tension textures;8,9,10 in particular, the aim has been to determine experimentally the end orientations of rolled single crystals of iron. These are discussed in connection with the point of view of Weverl and of Boas and Schmid2 that the rolling texture is a simple compression texture (compression normal to the rolling plane) superimposed on a simple tension texture (tension in the rolling direction), and the point of view of Kurdjumow and Sachs3 that three ideal end orientations exist. Experimental Method The single crystals used were in the form of disks cut from a stock of crystalst pre- pared in this laboratory by a strain-anneal method from mild steel decarburized and purified in hydrogen, the details of which have been described elsewhere.11 To ensure maximum elongation in the rolling direction and to simulate approximately the rolling of a grain in an aggregate, lateral flow was constrained by placing each crystal in a close-fitting hole in a plate of copper or iron of equal thickness and rolling the plate and crystal together. About one-third of the crystals were rolled in a "sandwich" pack by adding top and bottom cover plates. The two-high mill used had 8-in. diameter rolls and was operated at 15 r.p.m. The initial diameter of the crystals was between 1/4 and 1/2 in., while the starting thickness varied from 0.031 to 0.376 in. With a single exception, which was rolled 63 per cent, the crystals were rolled to a final reduction in thickness of 82 to 97 per cent in 20 to 40 passes, alternately changing the sense of the rolling direction. The initial orientations of the crystals were determined either by X-ray back reflection12 or by optical reflectionl3 from etch pits; the mean final orientations were determined by X-ray Laue photograms using molybdenum, silver, or tungsten radiations, by optical reflection, and in many cases by both methods. Results Twenty-six crystals were studied. It was found that there were three typical be-

Jan 1, 1941

By Charles S. Barrett, L. H. Levenson

Numerous determinations1-' of the texture of cold-rolled polycrystalline iron, steel, and ferritic alloys have been made with good agreement among the various observers as to the principal features of the texture common to all, but there has been no adequate explanation of the texture in terms of, the behavior of individual grains. This study presents an explanation of the texture based on the observed rotation of single crystals when deformed in a manner similar to a grain in the aggregate, a method we have found useful in leading to a better understanding of compression and tension textures;8,9,10 in particular, the aim has been to determine experimentally the end orientations of rolled single crystals of iron. These are discussed in connection with the point of view of Weverl and of Boas and Schmid2 that the rolling texture is a simple compression texture (compression normal to the rolling plane) superimposed on a simple tension texture (tension in the rolling direction), and the point of view of Kurdjumow and Sachs3 that three ideal end orientations exist. Experimental Method The single crystals used were in the form of disks cut from a stock of crystalst pre- pared in this laboratory by a strain-anneal method from mild steel decarburized and purified in hydrogen, the details of which have been described elsewhere.11 To ensure maximum elongation in the rolling direction and to simulate approximately the rolling of a grain in an aggregate, lateral flow was constrained by placing each crystal in a close-fitting hole in a plate of copper or iron of equal thickness and rolling the plate and crystal together. About one-third of the crystals were rolled in a "sandwich" pack by adding top and bottom cover plates. The two-high mill used had 8-in. diameter rolls and was operated at 15 r.p.m. The initial diameter of the crystals was between 1/4 and 1/2 in., while the starting thickness varied from 0.031 to 0.376 in. With a single exception, which was rolled 63 per cent, the crystals were rolled to a final reduction in thickness of 82 to 97 per cent in 20 to 40 passes, alternately changing the sense of the rolling direction. The initial orientations of the crystals were determined either by X-ray back reflection12 or by optical reflectionl3 from etch pits; the mean final orientations were determined by X-ray Laue photograms using molybdenum, silver, or tungsten radiations, by optical reflection, and in many cases by both methods. Results Twenty-six crystals were studied. It was found that there were three typical be-

Jan 1, 1941

By D. M. Shu

A two-dimensional finite element modelling technique is applied to predict the subsidence movements on a sloping ground surface above a completely mined panel. The modelling is carried out for the surface both directly and using a combination of an equivalent horizontal surface and a rays projection method and the result compared. The rays projection method provides the subsidence components on a sloping surface from the corresponding ones on an assumed equivalent horizontal surface through the point of mean elevation of the relevant part of the sloping surface. This method is used next to compare the subsidences, horizontal displacements and horizontal strains from the mining of a given panel at the surface for different inclinations. The results show that the magnitudes of the subsidence components are greater on the dip side of the slope from the point of the mean elevation, than the corresponding ones on the rise side and the asymmetry increases with the inclination of the surface. The findings are also compared with those of other research workers.

Jan 1, 1992

By James Fiore

The Nuclear Waste Policy Act of 1982 provides a set of rules for proceeding with the identification and selection of sites for a mined geologic repository as well as for interim storage facilities for high level waste in the event storage facilities are needed. The following paper summarizes the sequence of procedures in site selection, and presents the interaction of governmental agencies, the states, the public, and affected Indian tribes in this process. Several agencies have published regulations assocated with the selection of high level waste sites. These regulations set down a diverse collection of requirements designed to ensure public safety. This paper identifies the organizations working to satisfy these requirements, and outlines the role of the geotechnical community in performing data collection activities to support these same requirements.

Jan 1, 1984

By G. H. Enzian

THE effects of phosphorus and nitrogen on the properties and behavior of low carbon steels are important considerations to both the manufacturer and the user of such material. For one thing, these two elements are the principal points of distinction between the chemical compositions of Bessemer and open-hearth grades. Further, open-hearth steels themselves may vary considerably in nitrogen content depending on the raw materials and ..practice used. In addition, appreciable amounts of rephosphorized open-hearth steels are being used at the present time in some low alloy, high strength grades and in certain other cases. For these and other reasons, it was felt desirable to obtain more complete knowledge of the effects of simultaneous small variations in phosphorus and nitrogen content on such properties of low carbon steel as tensile strength, impact toughness, sensitivity to cold work, and strain aging. A long range investigational program designed to furnish such information, was carried out, and the present paper summarizes some of the data currently obtained. General Discussion The strengthening effect of relatively small amounts of phosphorus in steel has been recognized, and to some extent utilized, for many years. A number of investigators have pointed out, from time to time, that under proper conditions of control, phosphorus can be a useful alloying element in low carbon steels.1-3 Nevertheless, in spite of the volume of data on the subject, the use of phosphorus for this purpose has always been handicapped by widespread feeling that its presence makes the steel brittle, difficult to cold work, and unreliable at low temperatures. This belief on the part of some steel users is not entirely justified in many cases, and often stems from early experience with acid Bessemer steels which have appreciably higher phosphorus (and nitrogen) contents than basic open-hearth grades. Nitrogen in steel, and its effect on properties, has also received considerable attention in the literature.4 In 1906, Braune5 ascribed the brittleness of Bessemer rails to the nitrogen content, and proposed a schedule of nitrogen limits for steels for various uses. This was one of the first papers to recommend directly the use of nitrogen content as a quality control measure, but it did not meet with much favor or support; as a matter of fact, the Jernkon-toret was rather sharply criticized for publishing the paper. In the intervening years a number of papers have been published on the subject of nitrogen in steel. As a result, it is now generally recognized that nitrogen can have an important effect on the properties and behavior of steel and that the presence of this element should be considered in any systematic study of factors affecting steel quality. In 1932, Graham6 introduced the concept that the quality of various steels could conveniently be evaluated and compared in terms of "sensitivity", which was defined as "the characteristic reaction rate of a piece of steel toward brittleness or hardness." This concept formed the basis for a broad research program into factors causing variations in the quality of commercial steels. At an early stage of this work, it became apparent that the observed effect of either phosphorus or nitrogen on the sensitivity of steel depended, in no small measure, on how much of the other of these two elements was also present. Indeed, the combined effect of phosphorus and nitrogen in steel may often be more important than the specific effect of either. With a few exceptions, it is not possible to predict accurately the effect on steel properties of a change in the amount of either phosphorus or nitrogen in the steel without also specifying the approximate amount of the other element. It seems desirable, at this point, to discuss briefly the distinction between strain-sensitivity and strain aging as used in this paper. In the early stages of its development, the work-brittleness test7 (which will be described in more detail later) was used

Jan 1, 1951