Search Documents

By Kenneth R. Maser

In the past 30 years, great advances have taken place in the development of tunnel boring machines, raise drills, large diameter drills and blind shaft borers that have revolutionized the shaft sinking and tunneling industries. Techniques for placing concrete linings, however, have not changed significantly during this period, and still constitute a stumbling block to the achievement of the rapid construction. In the past 5 years, Foster-Miller Associates, Inc. (FMA) has been involved with the development of a remotely operated shotcrete system for lining raise drilled shafts, an Extruded Tunnel Lining System (ETLS) for lining TBM bored tunnels, and a Continuous Shaft Lining System (CSL) for lining any type of machine bored shaft. This paper presents an overview of these three developments, including capabilities and limitations, a description of the concrete production, concrete placement, and advance rate, and control subsystems, a description of the concrete mix development required for each system, a discussion of test results to date, and an assessment of the state of development of each concept. Plans for future development will also be presented.

Jan 1, 1981

By Heath E, van Calsteren P, Turner S, McDermott F

U-Th isotope studies of recent volcanic rocks may be used to evaluate the depths and rates of melt generation beneath mid- ocean ridges and ocean islands. Island arc rocks exhibit a similar range in Th isotopes to that seen in both MORB and OIB, but while those with high (230Th/232Th) tend to have excess 238U, many of those with low (230Th/232Th) are in isotope equilibrium. The excess 238U is attributed to the preferential mobilisation of U in hydrous fluids from the subducted slab within the last 100,000 years, whereas the low Th isotope ratios in the higher-K arcs are primarily due to the introduction of subducted sediment. Preliminary results from mineral separates from lavas on Soufriere on the island of St. Vincent indicate that some of the minerals crystallised up to 50,000 years prior to eruption.

Jan 1, 1995

By Chang-Yu Ou, Shao-Chi Chien, Hsuan-Hsiang Chang

"A field test was performed to investigate the applicability of electroosmosis with the injection of saline solution of Taipei silty clay. The calcium chloride solution and sodium silicate solution were used as the saline solution for the injection in this test. The results of this study indicate that injection using calcium chloride solution and sodium silicate solution during the electroosmosis to increase drained water from cathode and electro-chemical reaction can greatly improve the effect of electroosmosis and shorten the time of treatment. The results of field vane tests showed that the undrained shear strength after treatment increased an average of approximately 120% for a treatment period of 24 days.INTRODUCTIONThe first field application of electroosmosis in soil was demonstrated by Casagrande in 1939. Since then, more complete field applications of electroosmosis such as Bjerrum (1967), Fetzer (1967), and Lo et al. (1991b) have been made.The results of field electroosmotic work for a period of 120 days were presented by Bjerrum et al. ( 1967). The mean undrained shear strength, Su, increased from 18 to about 40 kPa, with a uniform surface settlement of about 0.5 m. Lo et al. (1991b), with a more sophisticated installation and a relatively larger spacing, also had positive results. For a 3 m electrode spacing during the treatment of a period of 33 days, the mean Su increased from 18 to about 25 kPa. Although the effect of the electroosmosis could be applied in the field based on the above examples, the response remained slow. For actual field work, the application of electroosmosis will be limited due to short project schedules and request of the effect of improvement."

Jan 1, 2005

By Richard Newcomb, Michael Rieber, William A. Vogely

INTRODUCTION The solid fossil and nuclear fuels, but especially uranium, are given prominent, indeed leading, roles by energy experts in most long range estimates of world energy futures. Optimistic forecasts are inspired partly by the disproportionately large solid fuels resource base compared to present rates of consumption or to oil and gas resources, and partly by the vision of inexpensive high technology applications. Such a view overlooks the fact that while resource- use disparities and new technologies give allure to the promise of the solid fuels, they do not guarantee cheap solutions to the basic problems of solid fuel uses: viz., their relatively difficult conditions for efficient ignition and control, including the management of environmentally acceptable residuals disposal. Contrary to the varied versions of this optimistic hypothesis, this paper shows that a great many persistent economic and technical problems interfere with such a simple inference. These act as constraints which qualify or dispute much of the national energy policy based on existing modeling of solid fuel requirements and optimistic engineering evaluations. The assumptions and techniques of such exercises are sometimes at fault. As often as not, however, the distortions created in open market fuel com- petition due to misdirected national energy policies themselves are to blame for misdirected efforts. A number of interesting implications result. Among them are the distinct possibility that the low technology applications will dominate, so that more direct coal and less synfuel or nuclear use will occur; that, accordingly, exhaustion rates for uranium will be low, that the most extensive growth of solid fuel through 2000 will be in conventional pulverized coal cumbustors, and that the traded share of the world coal bum will be much larger than predicted. These trends will place much more pressure on oil and gas prices than forecast by most experts. On the way to these findings the paper demonstrates that solid fuel resource adequacy in situ, balanced against the projections of demands as capacity requirements, mean little as conventionally measured by years to exhaustion or potential supply schedules. Indeed, all stock concepts of demand requirements or of fuel re- sources must be tied to the paths of the unit costs and the deliverable prices of all substitute fuels and systems over time. This requires a dynamic analysis of supply and demand, integrated with geological and engineering constraints, to provide insights into the multiple modes of market and product substitution. Market forces rather than technical promise will determine the allocation of the solid fuels. Moreover, the equilibrium paths of individual fuel prices and market shares are not easily simulated by general or network models, and decision makers will continue to rely on the partial, local comparison of alternatives in their choices of fuel systems at any time. 'The economics of the solid fuels differs from that of other energy sources in important ways relating to their form in use, conversion efficiency, (dis)economies and externalities. Petroleum and gas are in a more convenient form for

Jan 1, 1985

GENTLEMEN : Herewith are submitted reports for the calendar year 1933 of your Treasurer and the Chairmen of the following standing committees: Finance, Admissions, Membership, Papers and Publications, Library, and MINING AND METALLURGY. TO these reports you are referred for additional details of the year's activity. Finances.-Income for 1933 from all sources totaled $121,690 com- pared with $138,331 in 1932. Incidentally, this exceeded the income as estimated in the budget by $7,190; the largest item being a "surplus" of $3,316 over the budget expectancy as to member dues. As compared with 1932 the most important items of shrinkage in income were $9,000 from dues and initiation fees; $5,500 from the magazine, MINING AND METALLURGY; and $2,500 from sales of publications other than the magazine.

Jan 1, 1934

By Daniel N. Tallman

To provide technology for achieving more efficient water filtration systems for the mineral industry, the Bureau of Mines performed demon-stration filtration tests at three iron ore mines and one steel mill. A comparison of equivalently sized magnesium oxide (MgO) and sand filters showed that MgO had a higher capacity and could operate at higher fil-tration rates than sand. In demonstration tests when alum (AlK(S04)2) was the coagulant, suspended solids breakthrough occurred even though the pressure across the filter (head loss) was 7 psig or less. Under these circumstances, the MgO demonstrated 20 to 100 pct greater filtra-tion capacity, defined in terms of the volume of water filtered before breakthrough. When an organic floccu1ant was used at one location, head loss was the run-limiting factor; the filters essentially plugged with-out any solids breakthrough.

Jan 1, 1985

By Justin Karl, Ali Gordon, James DeMarco, Yongho Sohn

"Aluminum metal-matrix composites are lightweight materials that have the potential to supplant steel in many applications. The current work helps to identify the parameters that confer maximal strength and ductility. Torsion tests were performed on the as-cast aluminum metal-matrix composite A359-SiCp-30% at a variety of temperatures and twist rates. Dependence of material properties on temperature and strain rate were identified from equivalent stress-strain curves constructed from the reduced data. Examination of the microstructure was performed on the as-cast material and on fracture surfaces. A temperature-and strain rate-dependent constitutive model was applied to simulation of the mechanical response of the torsion specimen. Trends in material properties corroborate and extend trends identified previously under tensile loading with regard to temperature and strain rate dependence. Shear properties of simulated specimens agree with properties obtained through experimentation.IntroductionAluminum metal-matrix composites (A1-MMCs) have become increasingly popu1ar in recent years. While unreinforced aluminum alloys have low densities and high ductilities, they are not suitable for many applications due to their lack of strength and stiffness. To provide added strength and stiffness while maintaining favorable densities, it has become common to reinforce aluminum alloys with silicon carbide in various forms, although usually the inclusions are in the form of whiskers or particles. The result is a composite material with superior specific strength and stiffness. While whisker-reinforced composites are expensive due to the necessity of processing by nonstandard techniques and have low transverse properties when rolled, particle reinforced Al-MMCs have transverse material property values almost as high as the longitudinal properties and are not as expensive to process as whisker-reinforced Al-MMCs [1]."

Jan 1, 2012

By D. Van Dyk

Horizontal rotating mills are being used all over the world in different mineral and power generation industries. David Brown South Africa, with over 140 years of experience in gear manufacture and design, has been supplying these industries with innovative designs at exceptional quality. The gearing systems associated with these industries are challenged daily with operating conditions that are not always fully understood. Failures are therefore experienced, over time in the industry, which cannot always be fully explained. David Brown South Africa has developed a gear monitoring system, the Intelligent Gearing System, in association with Transmission Dynamics (UK), in order to monitor and analyse these operating conditions in real time. The system has been designed on the principles of Six Sigma, incorporating Design for Six Sigma. The purpose with this system design is to monitor the operating conditions on the pinion, record the information and analyse the data in relation to the rate of fatigue damage to the girth gear and pinion. This is done in real time and unattended. The output from the Intelligent Gearing System can be fed back into the operating system of the mill user, in order to display an alarm for operating conditions exceeding the design criteria as well as information on the rate of fatigue damage due to these operating conditions. When the mill operating and the effect on the fatigue life of the mill gearing components, conditions are better understood, mill users can forecast critical spare holding levels with an increased accuracy. The Intelligent Gearing System also allows early actions to remove reasons for system overloads.

Jan 1, 2006

By M. Kalin

Tailings deposits are frequently the source of ground water contamination due to the transport of contaminated tailings pore-water. If amendments to tailings covers could be made to facilitate a precipitation reaction and halt or reduce the generation of acid in pyritic tailings, the quality of pore-water quality would be improved which would in turn reduce the production of contaminants. The effects of phosphate wastes, added to base-metal mine tailings in Newfoundland, Canada, were tested. Laboratory and field experiments determined the effects of different mixing ratios of phosphate wastes to tailings volume (1:4, 1:8, 1:12 and 1:20, dry weight) for a total period of 3.2 years. The addition of phosphate at ratios of 1:4 to 1:12 substantially increased the pore water pH, and reduced both acidity and Zn concentrations. These results suggest that addition of phosphate wastes to tailings covers can reduce acidity generation and improve tailings pore-water quality.

Jan 1, 2004

By Clay Haynes, Tim Pearia, Robert Robinson, Judy Cochran

A 1.89 km-long, 4.5 m-I.D. tunnel was successfully constructed through saturated hard clay, and highly abrasive dense sand and gravel, with groundwater heads ranging from 10 to 20 m. In order to address these conditions, a Lovat earth pressure balance TBM was used, with soil conditioning by foam, water and various polymers. Support was provided by a single-pass segmented concrete lining. Groundwater inflows of 400to 1,600 lpm at times created challenges for changing cutting tools. Surface settlements were generally less than measurement thresholds, except under very low cover at startup. This project provides a pivotal case study of the successful application of EPBM technology in saturated, abrasive glacial soils and the successful application of soil conditioners.

Jan 1, 2003

By D. A. Swanson, G. Danziger, G. Savci, C. Barnes

Hydrologic assessments of existing and proposed waste rock stockpiles are typically required for application of operating and closure permits at mine sites. A hydrologic assessment should include an evaluation of climatic data and prediction of the net infiltration rate through the waste rock stockpile surface. In addition, hydrologic factors such as the time required to deplete available moisture storage in the stockpiles and the time required for potential seepage to migrate to the underlying aquifer should also be predicted.

Jan 1, 2000

By S. L. Couling, G. W. Pearsall

MOTT and Hainesl have summarized the available techniques for the examination of aluminum and some anisotropic metals under polarized light. Many of these techniques are rather complicated and cumbersome. This note presents a simplified procedure for using polarized light to obtain information about the crystallographic orientation of any particular grain in a magnesium alloy. Since other hexagonal metals are more anisotropic than magnesium, similar methods might well be applied to them. Ernst and Laves2 produced a double-refracting layer on magnesium alloy specimens by SuCCeSSiVe etches in solutions of perchloric acid in alcohol, magnesium perchlorate in perchloric acid and alcohol, and calcium and magnesium carbonates in water. They examined their specimens under polarized light and were able to determine the direction of the hexagonal axis in any particular grain from a measurement of the extinction behavior of that grain. The disadvantages of their technique were the complexity of the etching procedure and the explosive hazard of the perchloric acid-alcohol solutions. Results equivalent to those of Ernst and Laves were obtained in this investigation after etching specimens for 6 to 8 sec in an acetic picral solution containing 100 parts 6 pct picral, 10 parts distilled water and. 5 parts acetic acid. A. similar etch has been used by George3 in earlier metallographic

Jan 1, 1958

By David L. Huston, Wouter Bleeker, Bruce E. Taylor, Ron Cook, Bob Stewart, Elizabeth R. Koopman

"Abstract-Detailed oxygen isotope mapping of rhyolites in and around the Kidd Creek mine indicates that the orebodies are associated with relatively low (<12‰) whole rock values that extend up to 200 m laterally from ore. The zone of low d18O values is overlain stratigraphically by a carapace of higher (>13‰) values that extends up to 1.5 km laterally from and 300 m to 500 m above ore. Immediately above the stratigraphically highest orebody this carapace is cut by a zone of lower d18O values extending from the ore zone. Zones of higher d18O values also occur in massive rhyolite bodies that occur in the footwall of the orebodies.The zone of low d18O values partly coincides with a Na2O depletion anomaly associated with hydrothermal alteration, except that the Na2O depletion anomaly has a greater lateral extent, and the low d18O anomaly extends farther into the stratigraphic hanging wall. These data suggest that d18O mapping may detect hanging wall alteration above massive sulfide bodies more effectively than conventional lithogeochemistry. Zones of high d18O values, which define zones through which large quantities of low-temperature hydrothermal fluids have passed, may also have usefulness in exploration.Oxygen isotope variations at Kidd Creek record three stages of a hydrothermal system that evolved in temperature with time, as follows: (1) an early, low-temperature event that produced rocks with high d18O values, (2) a high-temperature event that produced rocks with lower d18O values, and (3) a later, low-temperature event that also produced rocks with high d18O values. The high d18O sig- nature of the massive rhyolite was recorded during early-stage, low-temperature (<200°C) alteration, and was probably preserved owing to decreases in permeability associated with low-temperature silicification. The low d18O signature of cherty breccia and chloritite was recorded during the thermal peak at >300°C. High d18O values in the carapace above the deposit were recorded as the hydrothermal system waned."

Jan 1, 1995

By E. Munnik

The Chambishi Metals Cobalt Plant in Zambia has recently installed a novel oxidation/precipitation pressure leach process as part of the COSAC (Cobalt from Slag and Copper as by-product) Project. An iron-cobalt-copper alloy, produced by the carbothermic reduction of slag, is atomized and pumped to the COSAC Leach Plant, where cobalt and copper are recovered as dissolved sulphate salts, and iron is rejected primarily as hematite. Cobalt and copper are subsequently recovered as cathode metal in the existing Chambishi operation by conventional electrowinning. This paper examines the challenges faced during the design and subsequent successful commissioning of the COSAC Leach Plant.

Jan 1, 2003

By J. Washburn

Two simple types of dislocation distribution were introduced into zinc crystal specimens and the effect of each on the stress-strain curve was investigated. Quantitative results were obtained for simple edge dislocation arrays and for an array of screw dislocations lying in the slip plane. A CCORDING to present knowledge, the disloca-tions present in large annealed metal crystals can be divided into two somewhat arbitrary groups: 1—single dislocation lines distributed more or less at random or forming elements of a three-dimensional network in which the distance between adjacent dislocations is of the order of 10 2 to lo-&apos; cm and 2— widely separated planar arrays of edge dislocations forming dislocation walls or small angle boundaries within which adjacent dislocation lines are spaced at much smaller distances (lo-&apos; to 10- hm). The former can be considered as a dislocation interpretation of the mosaic crystal proposed by Darwin and Ewaldl, &apos; 40 years ago to account for anomalously high integrated intensities of X-ray diffraction maxima. Small angle boundaries, although now known to be present in most single crystals used for mechanical testing, were not generally recognized by the early workers. This was partly due to the fact that only recently have improved X-ray and metal-lographic techniques been available for checking the macroscopic perfection of crystals."" It has long been known that changes in growth conditions and in annealing procedure, which might logically be expected to cause variations in the structural details of both the dislocation network and of dislocation boundaries, produce marked variations in some mechanical properties such as yield strength." However, no quantitative experimental correlations between changes in dislocation distribution and changes in mechanical properties have yet been made. Such a correlation has been difficult to obtain because, even when great care is exercised to keep the histories of a number of single crystal specimens identical, it usually has not been possible to avoid considerable variation in macroscopic per- fection.&apos; The number and orientation of dislocation boundaries vary from specimen to specimen. This has probably been an important contributing factor to the large scatter in the results of most mechanical measurements on pure single crystals. Some recent experiments"% ith single crystals of zinc have shown that the presence of dislocation boundaries in a specimen can increase its resistance to deformation by slip. With polycrystalline aluminum and nickel, there is also evidence that dislocation boundaries within the individual grains of the aggregate can increase the resistance of the material to plastic deformation, either as measured by tension tests at room temperature or by creep tests at higher temperatures.&apos;" " Although the foregoing observations seem to have established the fact that substructure can have a strengthening effect, the test conditions were too complex to give much information concerning the mechanism. In the foregoing cases, a network of intersecting boundaries having various orientations and boundary angles were present. Before their apparent strengthening effect can be understood, it will be necessary to isolate and study separately the effect of a number of variables: 1—boundary angle, 2—boundary orientation with respect to the active slip direction, 3—number of boundaries, 4—intersections of boundaries, 5—detailed structure of the boundaries, and 6—interaction of impurity atoms with dislocations in boundaries. The object of the present work was to study the effect of dislocation boundaries on flow stress under the following simple experimental conditions: 1— substantially pure shear deformation and 2—boundaries of controlled angle, orientation, and number. In this way, it might be possible to distinguish the important variables from the relatively unimportant ones. Experimental Procedure Stress-strain curves of hexagonal metals are generally nearly linear even out to very large strains."

Jan 1, 1956

By K. L. Whitehead, R. A. Jankowski, N. I. Jayaraman

Most continuous miner sections utilizing flooded-bed scrubbers also use blowing face ventilation. Blowing ventilation, however, interferes with dust capture and minimizes scrubber effectiveness. To enhance the efficiency of the scrubber system and reduce dust concentrations, the Bureau of Mines tested various combinations of operating parameters. Experiments for system efficiency took place in a full- scale model mine at 3.05 m roof height. In general, higher values for scrubber and face airflows resulted in lower dust concentrations. In addition, optimum dust controls would include a face ventilation to scrubber airflow ratio of one. When the airflow ratio was either less than or greater than one, the dust levels in the return and at the operator locations increased. No single dust control technique was the most effective one at all locations due to mutual interaction among techniques.

Jan 1, 1992

By R Piper

The Yabulu Nickel Refinery commissioned in 1974, processes lateritic ore via a modified Caron process to produce high quality nickel and cobalt products. The Greenvale orebody provided the sole source of feed to the plant until 1990 and with well-blended mineralogy, it resulted in stable and predictable plant performance, allowing the operating focus to be on reducing energy consumption and increasing ore throughput. This approach provided better economics than pursuing increased reduction efficiency. From 1990, increasing quantities of lateritic ore were imported from Indonesia, Philippines and New Caledonia. This introduced considerable variation in ore blends and instability in plant operation but also provided the opportunity to treat higher grade ore blends which yielded higher reduction efficiencies. Ore reduction is conducted using 12 Herreshoff multiple hearth reduction furnaces, using heavy fuel oil as reductant. The æROASTERÆ Project was approved in November 2000 with the primary objective of improving Nickel reduction efficiency by: Stabilising Roaster Operation via a structured program including focused maintenance efforts, capital equipment upgrades, new process measurements, process re-design and improvements to operating skills and process troubleshooting. A structured technical program including laboratory and plant studies using one plant furnace as a pilot unit to develop improved knowledge of how the reduction process proceeds in the Herreshoff furnace. Armed with this knowledge, optimised process conditions and a reduction process model were developed contributing to a significant demonstrated reduction efficiency improvement. Technical input to the project was provided by QNI with Hatch providing the engineering and project management for the $8.5 M capital work. Execution of the work included extensive consultation with the plant operators and close cooperation between the Hatch project team and QNI operations personnel ensuring installations were completed with minimal production disruption. A strong focus on safety management resulted in a number of brownfields project relevant safety initiatives being implemented resulting in project completion without a serious injury.

Jan 1, 2002

By C.H. Lorig, M.C. Udy

Through the years much interest has been centered in attempting to develop a direct method of iron-ore reduction, to replace or supplement the present indirect blast-furnace process. It would not be difficult to produce a list of more than 500 patents dealing with the direct production of iron and steel, but the few of this type of process that have proved successful do not produce in competition with the blast furnace; they produce special products. A survey of the literature reveals that the equilibrium conditions for the reduction reactions (iron oxides with carbon monoxide and with hydrogen) have been fairly well established but that data on the rate of reaction are discordant, although the genera1 effects of the variables are known. This dissertation deals with the rate of reduction of a magnetite concentrate with hydrogen. The following variables have been studied: bed depth, gas velocity, particle size and temperature. The behavior of a single particle was also studied. Literature Two general factors should be considered in a study of reduction of iron oxide: (I) equilibrium relations, and (2) rate of reaction. The first factor, equilibrium, has received the attention of many investigators and the equilibria Fe304-FeO-H2-H2O, Fe3O4-FeO-CO-CO2, FeO-Fe-H2-H2O, FeO-Fe-CO-CO2 are fairly well established. Of the second factor, the rate of reaction, much less is known. Data are comparatively scarce and there is very little concordance. The discordance probably results from the large number of variables influencing the reactions. However, the general effect of the variables is known. Among these variables are temperature, gas velocity, particle size, porosity, gas composition (distance from equilibrium), presence of impurities, greater or less prevalence of side reactions, and even design of the apparatus itself. Wetherill and Furnasl published an excellent paper in 1934. They point out that any one or more of five processes (the chemical reaction, diffusion of the reactant through the gas film, diffusion of the reactant through the solid phase, diffusion of the reaction product through the solid phase, or diffusion of the reaction product through the gas film) may be the slow process, and thus the rate-controlling process. It is regretted that the work of these authors was limited to experiments at One temperature, and that the range of gas compositions was limited. Langmuir2 has shown that heterogeneous reactions take place at phase boundaries.

Jan 1, 1943

By M. C. Udy, C. H. Lorig

Through the years much interest has been centered in attempting to develop a direct method of iron-ore reduction, to replace or supplement the present indirect blast-furnace process. It would not be difficult to produce a list of more than 500 patents dealing with the direct production of iron and steel, but the few of this type of process that have proved successful do not produce in competition with the blast furnace; they produce special products. A survey of the literature reveals that the equilibrium conditions for the reduction reactions (iron oxides with carbon monoxide and with hydrogen) have been fairly well established but that data on the rate of reaction are discordant, although the genera1 effects of the variables are known. This dissertation deals with the rate of reduction of a magnetite concentrate with hydrogen. The following variables have been studied: bed depth, gas velocity, particle size and temperature. The behavior of a single particle was also studied. Literature Two general factors should be considered in a study of reduction of iron oxide: (I) equilibrium relations, and (2) rate of reaction. The first factor, equilibrium, has received the attention of many investigators and the equilibria Fe304-FeO-H2-H2O, Fe3O4-FeO-CO-CO2, FeO-Fe-H2-H2O, FeO-Fe-CO-CO2 are fairly well established. Of the second factor, the rate of reaction, much less is known. Data are comparatively scarce and there is very little concordance. The discordance probably results from the large number of variables influencing the reactions. However, the general effect of the variables is known. Among these variables are temperature, gas velocity, particle size, porosity, gas composition (distance from equilibrium), presence of impurities, greater or less prevalence of side reactions, and even design of the apparatus itself. Wetherill and Furnasl published an excellent paper in 1934. They point out that any one or more of five processes (the chemical reaction, diffusion of the reactant through the gas film, diffusion of the reactant through the solid phase, diffusion of the reaction product through the solid phase, or diffusion of the reaction product through the gas film) may be the slow process, and thus the rate-controlling process. It is regretted that the work of these authors was limited to experiments at One temperature, and that the range of gas compositions was limited. Langmuir2 has shown that heterogeneous reactions take place at phase boundaries.

Jan 1, 1943

By Gordon Demetrick

3900 Yonge St. was not a typical site on which to build a condominium apartment. A steep hill covered the majority of the site. In order to use as much of this site as possible, the rear of the building was to have nine stores cut into the face of the hill. A permanent shoring system was required as the building structure was not designed to provide sufficient stabilizing elements to support the total earth pressure. The total excavation depth required was 36 m (120&apos;-0") with the upper 12 m (40&apos;-0") to be backsloped. The vertical face of soil to be supported was 24 m (80&apos;-0&apos;). The shoring system originally designed by the Structural Engineer was to support this face by installing soldier piles and inclined earth anchors. During bid preparation it became evident to us that the system as designed would be difficult and expensive to install due to wet soil conditions. An innovative design was required to overcome these problems. Anchor Shoring hired John Stephenson Consultants Ltd. to aid them in accomplishing this goal. After extensive investigation together with The Trow Group, a unique design was proposed which provided a practical solution to the shoring problem.

Jan 1, 1987