Search Documents

Secretary's NOTE—on page 176,of this paper, in the fourth line of the first footnote, " 4° " should, be " 1" )'; and on page 180, at the beginning of line 23, ('lined boot" should be " unlined boot." Discussion. Frank Owen, London, Eng. (communication to the Secretary) : In his very interesting and valuable paper, Prof. Snow

Jan 1, 1900

By B. T. Lu, J. L. Luo, H. X. Guo

This paper investigated the synergistic effect in the slurry-erosion process of carbon steel. In line with the mechanisms of material loss, the synergism due to interaction of erosion and corrosion was divided into the corrosion enhanced by erosion and erosion enhanced by corrosion. The erosion-corrosion tests were conducted with A1045 steel in slurries containing silica sand. Experimental results showed that the rotating of the sample in corrosive media raised both OCP and corrosion rate, but the impingement of solid particles did not affect the corrosion current significantly. In the quiescent solutions, the Faraday's law gave a good prediction for the weight loss caused by corrosion but for rotating samples, the weight loss experimentally measured was virtually greater than that predicted by the Faraday's law, indicating that the corrosion-enhanced erosion could occur in corrosive fluids in absence of solid particles. A half-logarithm relationship was observed between the weight loss due to corrosion-enhanced erosion and the anodic current density.

Jan 1, 2004

By E. Pezennec

A voluntary comprehensive environmental Risk Assessment was launched at the end of 2004 by the International Chromium Development Association. The completion is scheduled for mid 2006.EURAS, a leading environmental consultancy, was commissioned for this project, as this firm wrote in particular the Metals Environmental Risk Assessment Guidelines, the reference document for the metals and metals compounds, in particular for the forthcoming European new Chemical Policy and the Globally Harmonized System for the Classification and Labelling of Chemicals (GHS). This project follows a stepwise approach, comprising 3 distinct steps: - Initial Risk Assessment: compilation, evaluation of the existing effects and exposure data for chromium III compounds and chromium metal. This information will be used for the compilation of an initial Risk Assessment Report. - Data gap analysis: which type of additional effects data should be collected and/or which exposure scenarios merit a more detailed targeted risk assessment? Recommendations and/or suggestions for further research will be formulated. - Road map: prioritization and ranking of the different proposed research programs. The presentation will mainly focus on the results and recommendations of the initial environmental Risk Assessment from an International perspective and not from an European point of view. - Hazard assessment ? definition of the Predicted Non effect Concentration (PNEC) for each environmental compartment (water, sediment, soil) - Exposure assessment ? definition of the Predicted Environmental Concentrations (PEC) for each environ-mental compartment - Comparison of the local PEC with PNEC for the chromium III compounds and chromium metal EU industry sectors covered in the project: mining of chromite, metallurgical production of chromium metal, chromium containing alloys production, production of trivalent chromium chemicals and the main applications (pigments, leather tanning, etc..). The current status on the environmental Classification and Ranking for chromium III compounds, Chromium metal and its alloys in the GHS will also be covered.

Jan 1, 2007

[ ]

Jan 1, 1942

By Eric Westman

Ground control problems caused by multiple-seam interaction frequently sterilize coal reserves. Interaction mechanisms differ for overmining and undermining and are controlled by mining, spatial. and geologic conditions at each site. A multiple-seam interaction analysis software program, UGLY (Uppersearn Gateroad Longwall Stability), has been used to evaluate sterilization of coal reserves due to overmining at three locations. Four case histories were reviewed to determine the effectiveness of improved ground control in mitigating interaction effects.

Jan 1, 1997

By Waldemar Lindgren

Fifteen years ago, in his presidential address before the Washington Academy of Sciences,' Alfred H. Brooks said: "Applied geology can only maintain its present high position by continuing the researches which advance the knowledge of basic principles. Future progress in applied geology depends on progress in pure geology. Early in 1927, Dr. David White, then chairman of the Division of Geology and Geography of the National Research Council, appointed a committee "On the Processes of Ore Deposition," which was the first recognition by the Council of this branch of applied geology. This committee will not be able to solve the many complex problems involved; it can only clear the way, survey the field, state the problems and encourage systematic research. This short paper aims to outline and to analyze the present status of this kind of geological research, to ascertain the quality of the work and to suggest lines that might profitably be followed. Increasing Demand for Geologists Economic geology, or the art of geology, could develop only after the principles of geology and mineralogy had been established. Before that time it was merely a collection of trade rules accompanied by more or less wild speculations. Thus we observe the beginnings of economic geology in the period 1770-1820. Soon afterwards, the State Surveys were established in this country, with the realization that the natural resources should be investigated and described. Geology was hardly yet equal to the task of scientific research in relationships and genesis, however, and there followed a period of discouragement and stagnation. In the meanwhile, pure geology had again registered progress, and, based on its principles and also on the rapid mining development in the Cordilleran region, the present phase of the study of ore deposits began to take form. Raphael Pumpelly, S. F. Emmons and G. F. Becker were among the pioneers in this movement. The United States Geological Survey was organized. Ore deposits were scientifically described and studied along lines of structure and mineralogy; theories of genesis were advanced, not always permanent but based on sound induction.

Jan 1, 1928

By Frank E. Federspiel

In 1986 and 1987, at the request of the U.S. Forest Service, the U.S. Bureau of Mines examined the 47,000-acre Electric Peak study area (part of the formerly-designated RARE II Non-wilderness Recommended Area no. 1609) to evaluate its' identified mineral resources. The study area is in Powell and Jefferson Counties, YT, about 30 mi southwest of Helena and 30 mi north of Butte. Three lode localities within the study area contain an estimated 159,000 tons of identified subeconomic resources containing gold, silver, and accessory lead, copper, and zinc. Resources at those localities range from 10,000 to 134,000 tons with grades ranging from 0.04 to 0.32 oz/ton gold, 0.92 to 16.42 oz/ton silver, 0.14 to 79.65 percent lead, and as much as 0.41 percent copper and 0.68 percent zinc. One property also contains 0.15 percent antimony. Gold, silver, and base-metal content in samples of poorly exposed mineralized structures indicate that further exploration may identify resources on seven additional study area localities.

Jan 1, 1988

By C. A. O’Connell

Surface exploration drilling at Mufulira started in 1928, with drillhole No. 1 intersecting ore near the eastern fringe of the deposit. Subsequent drilling along strike intersected ore until the western fringe was fixed some 7500 ft west of drillhole No. 1. Further intensive drilling down dip disclosed a large triangle of ore with its apex 3350 ft deep. It contained approximately 11 6 million tons of ore at 4.41% total copper in three superimposed orebodies. The east and west limits of the orebodies were presumed to have a pronounced rake to the north with a strike length of 8000 ft. Subsequent exploration underground seemed to bear out this presumption to the 1150 ft level. In 1947, attention was directed to the area west of the known orebodies in conjunction with plans for increased production and increased depth of the mine workings.

Jan 12, 1962

By J. B. Rather

The use of sulfuric acid in refining illuminating oils antedates the beginning of the petroleum industry in America by many years. It was used as early as 1792 by Tower in refining "coal oil" in the British Isles, and by 1860 there were 53 refineries in the United States manufacturing "coal oil," most of them using sulfuric acid as a refining agent. Following the completion of the Drake well in 1859, many of the "coal oil" refiners began to use petroleum for manufacturing illuminating oil, and their methods and equipment were adapted so far as possible to this new raw material. The value of sulfuric acid in refining L'coal oil" having been established, this reagent was immediately tried and found to be satisfactory in refining petroleum. Notwithstanding the tremendous advances in petroleum technology since that time, sulfuric acid remains today the most valuable and most widely used means for refining petroleum products. Early Methods of Disposal of Acid Sludge With the almost immediate expansion of the petrolrum industry came the problem of disposing of the acid sludge produced in the refining operations. While in 1859, the year of the discovery of the Drake well, a patent was granted for sludge separation and separated acid concrntration, most of the earlier refiners, and rnany of their successors, felt that separation and recovery of spent acid was uneconomical. Accordingly, many of then) disposed of the sludge in any way that seemed expedient nt the time. It was huricd in the refinery grounds, harged and tlurnped at sea, run into neighboring streams, or dumped into sewers. Some optimists carted it to open pits in the hope that it would eithcr sink into the ground or evaporate. Not so many years ago, the superintendent of nn eastern refinery, who was using the open-pit method of disposal, lost, a sludge cart, with horse attached, in such a pit. The horse was recovred almost immediately, but its availability for further use was reduced to zero by the loss of its hair.

Jan 1, 1928

Trial ore production began at the Hilton Mine in 1987 with ore being trucked into Mount Isa for treatment at the Lead/zinc Concentrator. The expansion of output from the Hilton mine required additional concentrator capacity which led to the design and construction of the Hilton Concentrator. Systematic laboratory and Pilot Plant testwork dating back to 1968 to develop a flowsheet and reagent regime suited to the varied and generally complex mineralogy of the Hilton ore was successfully concluded with a Pilot Plant trial using a sulphoxy based sphalerite depression system in early 1988.In May 1988, a decision was made to build a 750 000 t/y concentrator with some novel technological and capital-efficient features. The Hilton Concentrator commenced operations in December 1989 reaching target grinding rates and metallurgical performance by mid-1990. Current ore treatment rate is 800 000 t/y.Lead concentrates assaying 43 - 48 per cent Pb are combined with the Lead/Zinc Concentrator lead concentrates and smelted at Mount Isa. Zinc and Low Grade Middlings (LGM) concentrates are filtered in the zinc filter plant at Isa with those from the Lead/Zinc Concentrator and then railed to Townsville for export or treatment in Australia.

Jan 1, 1993

By V. Dezelic, D. B. Apel

This paper describes the results of laboratory and field experiments conducted to determine the applicability of Ground Penetrating Radar (GPR) for the assessment of the strata thickness and for the identification of separation between bedding planes in stratified rocks. The knowledge about the extent of such separation in the roof layers and information about roof lithology can be used to determine the roof support requirements for underground mines where stratified rocks are present. The laboratory and field experiments were conducted at the Rock Mechanics Laboratory and the Experimental Mine at the University of Missouri-Rolla. The 1.5 GHz high resolution, shallow depth GPR antenna was used for all of the experiments.

Jan 1, 2004

By K. A. Elbarawy

Processing of Egyptian barite ore with a composition of 85.5% BaSO4; 2.75%SiO2;1.56%Fe2O3 and 5.1% Al2O3 was performed with the aim to prepare pure barium salts. The process took place through pelletization-solid state reduction and leaching steps. Each of these steps was optimized. Pure barium sulphate (99% < 0.82µm) and carbonate (99%<0.75µm )were the final products. This article deals with the reduction process that occur whn coal was added to the ore during pelletization in the ratio of 5:1 stoichiometry. Optimum reduction of pellets of 8-12mm in diameter was achieved after 60 minutes at 1050oC and under a rate of 5 lmin-1 of nitrogen atmosphere, where 87.79% of the ore was reduced. The kinetic studies showed that the reduction process could be modeled according to the core mechanism of diffusion control in which the effective diffusivity is based on the surface area of unreacted ore. The activation energy calculated was 92.7 kJmol-1.

Jan 1, 2006

By W. H. Adams

Among the engineering plants with new features and deserving details which are constantly being brought to the working stage in the Southern States by the generous expenditure of capital, none can exceed in interest, whether to the public or the profession, the incline-railway built from base to summit of Lookout Mountain, near Chattanooga, Tennessee. Much geological and historical interest centers in this section of the middle mountain-country. Of its geology, the Transactions of the Institute contain many particulars. Of its history, the most

Jan 1, 1888

By S. K. Kawatra, R. A. Seitz

Nonpolar hydrocarbon oils are commonly used in the flotation of minerals to fulfill a number of roles. These roles include reducing overall reagent costs by replacing part of the collector addition, improving coarse particle recovery without reducing selectivity, as well as several others. This paper will cover the types of oils which are available, their physical and chemical characteristics, and the effect of these characteristics on the function of hydrocarbon oils in flotation. In addition, techniques for improving the behavior of oils will be discussed.

Jan 1, 1986

By Sung-Hyun Park

Core sediment samples collected from the KODOS area of the Clarion-Clipperton Fracture Zone in the NE Equatorial Pacific were analyzed for chemical and mineralogical compositions to investigate the depth- and time-related variation of paleoenvironmental and paleoceanographic conditions during their deposition. These core sediments are divided into three layers from top to bottom by its color; 1) brown layer (Unit I), 2) pale brown layer (Unit II), and 3) black brown layer (Unit III). Geochronology of 10Be indicated the depositional age of Quaternary for Units I and II and of late Pliocene for Unit III with a potential short hiatus between them. Analyses of interelemental correlation identified three major groups of elemental groups that show moderate-to-strong correlations: 1) Al, Ti, K, and Fe representing for terrestrial alumino-silicate fraction of sediments, 2) Ca, P, REEs, Cu, and Zn for biogenic apatite, and 3) Mn, Ni, and Co for hydrogenous Mn-oxide. With an exception, Fe content was very high and showed fair correlations with Mn, Ni, and Co in Unit III. Unit III shows high smectite but low quartz and illite contents compared to the overlying two units, indicative of reduced supply of terrestrial materials. In a meanwhile, major elements (Fe2O3, CaO, P2O5), minor elements (Cu, Zn) and REEs are highly enriched in Unit III compared to the upper two units. All these elements other than Fe reflect the fraction of biogenic apatite, which indicates higher fraction of biogenic components in Unit III. This is also supported by higher amount of smectite formed by the consumption of siliceous biogenic components. The reduced supply of terrestrial material and/or increased productivity of surface water at the time of Unit III deposition are attributed to Pliocene warming preceding Northern-pole glaciation during Quaternary. Unit III also includes clinoptilolite and unidentified 8Å mineral, likely amphibole, that are absent in Units I and II, suggestive of the possibility of different source region and/or materials during Pliocene. Higher contents of Mn and Fe in Unit III are likely due to the high fraction of Mn-oxide that was formed by diagenetic process after deposition.

Jan 1, 2003

By L. D. Hall, S. J. Rothman

DIFFUSION coefficients of RaD (PD) and RaE (Bi) in a Bi-0.255 atomic pct Pb alloy have been measured by the methods outlined in a previous paper.&apos; The following changes were made in the experimental procedures: the bath was made up of about 400 to 500 g Bi; and no correction was made for the volume change of bismuth on melting. The data are presented in Table I and Fig. 1. A least-squares analysis of the data yielded D = (0.120 t 0.09) exp ( -9680 + 1070/RT) D- (0.0465 0.001) exp (-8100 + 466/RT). Statistical analysis of the data indicated that the activation energies are significantly different at the 50 pct level, but not at the 75 pct level, while the D values are significantly different at the 97.5 pct level, but not at the 99 pct level. The differences are thus not as clear-cut as they were for lead. However, bismuth diffuses faster than lead in high bismuth alloys as well as in lead. The high activation energies, more than twice the value calculated from viscosities, are in good agreement with the results of Grace and Derge.&apos; No data were obtained at higher temperatures because of gas bubble formation in the capillary. Acknowledgments This work was supported by the Office of Ordinance Research under contract DA-04-200-ORD-178. The authors thank 0. P. Vieria and M. Volpe for help in the experimental work.

Jan 1, 1957

Acupan is considered to be an intrusive centre as several igneous phases have been emplaced in the vicinity of the mine over the past 8 Ma. They include the Lucbuban gabbro, Virac granodiorite, Ampucao dacite porphyry (ADP), Hartwell plug, Itogon plug and the multi-phase Balatoc diatreme. These intrusives have high-K calc-alkaline affinities and are grouped together as the Virac Complex.Porphyry-style mineralisation formed during the final crystallization of the ADP in the late Pliocene, with the deposition of two vein stages from high-temperature hypersaline magmatic-hydrothermal fluids. K-silicate alteration halos surround the first stage of veinlets (stage I); they are surrounded in turn by a propylitic assemblage. White sericite and/or intense propylitic halos envelop the second stage of veinlets (stage II) and grade into a weak nrnnvlitir accPmht o

Jan 1, 1990

By Hryniewicz M

The paper presents a sound critical estimate of mathematical models presently used for the process of compaction of fine-grained materials. It shows the mathematical model of compaction developed by the authors, which was used to formulate the program of computer simulation of the process. The examples of computer simulation experiments of compaction of selected fine-grained materials regard the results of the experiments made by the authors on variability of external friction occuring in this process. Simulation examination presented in the paper crucially contributed towards the original method of selection of rational compaction technologies of fine-grained materials developed by the authors.

Jan 1, 1993

By James W. Dally, William L. Fourney, Anders Ladegaard Peterson

For the past 3 years, the authors have been conducting research sponsored by the National Science Foundation (RANN) to improve the process of excavation by drilling and blasting. The approach followed has been experimental where the development of stress waves and fractures initiated at the bore hole have been investigated in order to obtain a complete understanding of the dynamic Fracture process. The second step in the approach has been to introduce modifications in the drill and blast procedure which will permit closer control of the fracture process.

Jan 2, 1978

By Jean-François Domgin

This paper aims at presenting numerical results showing the impact of different parameters on the limitation of entrained slag from ladle to tundish during the ladle drainage. These parameters are process parameters, slag properties or external actuator acting directly on ladle slag behaviour. Numerical simulations based on the use of the CFD Fluent software illustrate the vortexing and non-vortexing phenomena appearing during the ladle drainage. This numerical tool validated by experimental data acquired on water model has been applied to industrial configurations. It shows that the slag properties (viscosity, surface tension?) or some modifications of parameters (slide gate opening, geometry of the ladle bottom?) have a positive effect on the slag entrainment and also on the decrease of the ladle heel. Finally, the modelling of the behaviour of an external actuator injecting some gas in the region of the nozzle reveals interesting possibility for reducing slag entrainment from ladle to tundish during the final steps of the drainage.

Jan 1, 2006