Search Documents

By Renato G. Bautista, Theodore D. Tiemann

A kinetic study of the hydrogen reduction of taconite from the Wisconsin Gogebic range was made over the temperature range from 500° to 1000°C on eleven size fractions from 4 to 150 mesh. Two stages of reduction were observed, a rapid initial reaction followed by a slower reaction presumably taking place at an internal receding FexO-Fe interface. Calculated mean activation energies for the two reactions were 7800 and 14,600 cal per mole respectively. In recent years there has been an increased interest in the direct reduction of iron oxide ores to metallic iron by means of gaseous reducing agents such as hydrogen and carbon monoxide.1,2 These investigations have been motivated by the desire to develop a process that will by-pass the blast furnace in the production of steel. The majority of these processes have been developed to produce metallic iron by direct reduction from high-grade iron oxide ores.3"5 Very little work has been done on the low-grade siliceous iron oxide ores.6"8 The work reported here is directed principally towards the fundamental aspect of the reduction reactions of siliceous iron oxide ores, since the practical aspects of the gaseous reductant process were discussed previously. The ore used in the investigation was obtained originally from the United States Bureau of Mines10 trench sample of the Yale member of the Wisconsin Gogebic range iron formation. The Yale taconite has an average analysis of 28.2 pct Fe and approximately 50 pct SiO2. Chemically, these nonmagnetic taconites contain on the average about 53 pct silica and 30 pct Fe. An average analysis calculated fron the USBM10 figures for a composite of the five members (Norrie, Plymouth, Pence, Pabst, and ale) of the iron formation is given in Table I. Mineralogically, based on previous X-ray diffraction and other studies, the principal minerals are hematite (Fe2O3), geothite (Fe2O3.H2O), and quartz (SiO2). Minor amounts of iron containing silicates, siderite (FeCO3) and magnetite (FeO. Fe2O3) are present.10,11 The iron minerals and the quartz are finely disseminated requiring extremely fine grinding for liberation. For the experimental work, the ore sample was screened into a number of size fractions, the analyses and densities of which are given in Table II. EXPERIMENTAL PROCEDURE The reduction experiments were carried out in a 24 in. by 2 in. ID nichrome-wound vertical-tube furnace mounted on a stand. A 1 1/2 in. OD zirconium-oxide combustion tube was used inside the furnace to contain the atmosphere. To the top of this combustion tube was joined a pyrex ground-glass joint to which was attached a glass bulb with a small (1.0 mm) opening at the center, and with two outlets controlled with a stopcock on each side. A pyrex-glass joint with connections to three stopcock joints for introducing hydrogen, nitrogen, and mixtures of hydrogen and nitrogen gas was joined to the tapered bottom of the combustion tube. The sized ore fractions were contained in a 1 in. diameter by 1 1/2 in. 150-mesh nickel screen basket. The basket was suspended in the furnace from a balance by means of a supporting nickel wire which hung freely inside the combustion tube. The furnace temperature was controlled by a Leeds and Northrup Speedomax Type G controller, connected to a chromel-alumel thermocouple placed

Jan 1, 1962

By A. U. Seybolt

In part 111' of this series it was shown that during the selective oxidation of a 3 1/4 pct Si-Fe alloy in damp hydrogen, only silica, (observed at room temperature) as low cristobalite or low tridy-mite or both, was formed as an oxidation product. In some in- „ stances where the film was fairly thin (probably well under 100A) there was some suggestion of an amorphous form of SiO2. The present investigation of oxidation rate showed that the selective oxidation of silicon-iron can be rather complicated, and apparently impossible to rationalize in an unequivocal manner. In some temperature regions, notably near 800" and 1000°C, the data seem to obey the familiar parabolic rate law. However, at intermediate temperatures complications were noted, some of which are possibly due to the order-disorder reaction in the silicon-iron solid solution. IN an earlier report' it was shown that during the oxidation of 3 1/4 pct Si-Fe alloys in H2O-H2 atmospheres only silica films were formed in the temperature range from 400° to 1000°C in hydrogen nearly saturated with water at room temperatures, or at dew points as low as -45°C. In the work to be reported here, some observations are made on the rate of oxide film formation. As in the earlier investigation, electron diffraction patterns generally showed either low tridymite or low cristobalite or both, except for some very thin films. These sometimes showed diffuse rings, presumably due to a very small crystallite size, or in a few cases, diffuse bands probably caused by an amorphous film. EXPERIMENTAL PROCEDURE Vacuum-melted silicon iron made of high-purity materials was rolled into strips 0.014 in. thick, and cut into samples 1/2 in. wide by 1 in. long. Chemical analysis showed 3.2 pct Si and 0.002 pct C. All samples were surface abraded with 600-grit paper, were solvent cleaned, and then placed in an paper,apparatus containing a "Gulbransen type"2 micro-balance. Here the gain in weight of the samples of about 5 sq cm area could be followed as a function of time during the oxidation caused by the water in atmospheres of various controlled water-hydrogen ratios. The water-hydrogen ratios can most easily be described as varying from a dew point of 0°C (PH2O-p^2 = 6.2 x 10-3 , to K (P j -40°C (PH2O/PH^= 1.3 X 10-* Most of the experiments were conducted at the 0°C dew-point atmosphere because drier atmospheres caused so little gain in weight that the accuracy of measurement was poor. Because of this, only the data obtained at PH2O,/P,,,= 6.2 x X3 will be reported. The temperature range extended from 800" to 1000°C; and most of the oxidation runs lasted for about 24 hr. The reproducibility of any reading was about ± 1 ?, but the sensitivity of the balance was about 0.2 ?. The atmosphere, flowing at 200 cm per-min, was preheated to the furnace temperature before contacting the specimen. While the gas flow caused a measurable lift on the sample, it was ordinarily sufficiently constant so that it was not an appreciable source of error. X-ray and electron diffraction checks of the samples before and after oxidation showed no evidence of preferred orientation, either on the metal samples or on the silica films formed. EXPERIMENTAL RESULTS The data obtained are summarized in Table I, and some are given in detail in Figs. 1 to 4. In the fourth column of Table I, kp refers to the parabolic rate constant in the expression (?/cm2)2 = kpt + c [1] where ? = micrograms gain in weight kp = parabolic rate constant in units r2 /cm4 t = time in minutes c = constant It will be noted that in many cases no value for kp is given; this is because in these instances the data did not obey the parabolic rate law. The silica film thicknesses given in the last columns are values calculated from the weight gain, an average tridy-mite-crystobalite density, and by assuming a perfectly plane surface. Fig. 1 shows the data plotted in the form of Eq. [I], hence a linear plot indicates parabolic behavior. It has been frequently observed in the literature that

Jan 1, 1960

By William J. Potter

The current financial environment differs markedly from past commodity price expansions, which have benefited the mining industry. Deregulation, financial innovation, and the globalization of capital markets in the 1980s have altered financing and investing patterns. Investment bankers and smart money within the industry have recognized the alterations and trends that facilitate fee revenue and profitable growth. This paper profiles transactions exemplifying change and documents financing techniques or instruments that have developed during the past half decade, emphasizing equity in the global marketplace.

Jan 1, 1990

By Ernest Peters

To model the zinc pressure leach, equations have been written that describe the rates of individual reactions taking place, including (a) oxygen mass transfer, (b) ferrous oxidation by dissolved oxygen, and (c) ferric reactions with ZnS and other minerals. In the continuous process, at steady-state, these take place at the same rate, and so the equations can be solved simultaneously. Model calculations using simultaneous equations are shown in graphical form to demonstrate the effect of different variables on the leach performance.

Jan 1, 1993

Arm Royalty systems of different types are used throughout Australia by both state and federal governments to raise revenue and thus facilitate in the proper distribution of mineral wealth. Royalty systems should be neutral and equitable but by their very nature these objectives are impossible to obtain. Because of the individual nature of mineral deposits, in particular variable cutoff grades and tonnages, governments should be aware of the possible trade off between short and long term gains of the particular royalty scheme introduced.

Jan 1, 1982

By George M. Bouton, Lawrence Ferguson

The experiments described in this publication were inspired by the Bell System's large interest in lead-alloy sheathed cables and by the wide range of fatigue and corroding conditions to which they are sometimes subjected in service. The first experiments consisted of operating specimens of lead + I per cent antimony telephone cable sheath alloy in a fatigue test while they were immersed in water taken from a manhole. Because of many published reports concerning corrosion-fatigue phenomena of various metals and alloys, a reduction in fatigue life was expected(1)2 Instead, however, the fatigue test ran on for many times the normal number of cycles an4 was finally stopped without failure. Because of this, the experiments were broadened to include the effect of many media on the fatigue properties of four lead alloys over a wide range of testing speeds and strains. One material, a viscous tacky polymerized isobutylene3 used in

Jan 1, 1945

By Forrest T. Moyer

To keep the mineral and allied industries informed of trends in the causes of accidents and to point, out the need for corrective measures, the Bureau of Mines collects, analyzes, and periodically publishes health and safety statistics. This report includes data for 1962 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following: General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1964

By E. L. Atkinson, G. W. Leach

The paper discusses the reasons for the introduction of load-haul-dump (LHD) units into Greenside Colliery, and the circumstances leading to the replacement of conventional mechanized equipment on a trial basis in the mining operations on No. 2, 4, and 5 seams. An outline is given of the factors governing the selection and introduction of these units into coal mining, and the associated mining and engineering aspects involved in the optimization of their use. Operating statistics comparing the performance of conventional and LHD equipment are included.

Jan 1, 1979

By J. D. Livingston, Bruce Chalmers, R. L. Fleischer, R. S. Davis

INTERACTION of dislocations on intersecting slip planes has long been considered a primary cause of work hardening in metals. Easy glide and low work-hardening rates have been observed experimentally only when single-crystal specimens were oriented so that one slip plane was initially favored. When single-crystal specimens have been oriented so that initially two or more slip planes were equally favored, high initial work-hardening rates have been observed. In a polycrsstalline aggregate, glide on five systems is in general necessary for a crystal to deform in conformity with the change in the shape imposed by the other crystals.* Only a small fraction of the crystals of a polycrystal will be oriented so that two

Jan 1, 1958

By S. Maluadzi, D. Rocchi, S. Luyckx, S. S. Potgieter-Vermaak, C. Machio, J. H. Potgieter

The aim of this work was to compare the corrosion behaviour of thermal spray WC ? based coatings before and after annealing. X-ray diffraction (XRD) was used to determine the phases present in the coatings at various stages. The corrosion resistance of the coatings was measured using electrochemical and immersion corrosion tests. The results obtained from electrochemical corrosion (quantified by corrosion current density) and immersion corrosion tests showed that annealing appears to decrease the corrosion resistance of the coatings. From the XRD results it was determined that the phases that corroded preferentially were cobalt (Co), eta (Co6W6C) and W2C. Keywords: Corrosion, thermal spray, coatings, hardmetals.

Jan 1, 2006

Deformation of the lithosphere by tectonic forces is investigated from both observational and theoretical standpoints. Global and regional geophysical data bases, coupled with the means for their rapid display and analysis, facilitate recognition of areas of the con- tinents and oceans where the response of the lithosphere to these deforming processes might fruitfully be studied. Gravity anomalies, from Seasat altimeter data and from land and shipboard measurements, provide critical infor- mation on the isostatic state of deformed lithosphere and therefore on its thermal and mechanical properties.

Jan 1, 1987

By L. R. Jackson

It is convenient to have a consistent system of notation that will allow the representation of the entire range of complex stresses from hydrostatic compression to hydrostatic tension on plastic flow in a single diagram. Such a system is provided by making use of the fact that any complex stress system can be resolved into a hydrostatic tension or compression and a pure shear. Consider a stress system having the principal stresses This system can be resolved into a new system consisting of the three components and three pure shears. If Sm is positive, the net stress effect is hydrostatic tension; if it is negative, the effect is hydrostatic compression. In order to produce a systematic notation, a quantity that will be referred to as the "triaxial ratio" will be defined by the equation _ Sm Tr = Sm - Sm is given by Eq. I and Sl is the absolute magnitude of the largest principal stress without regard to sign. Table I lists the triaxial ratios for various common systems. Table i.—Triaxid Ratios for Various CommonSyslems Triaxial Ratio Stress System Tr Hydrostatic compression — SI - —St - -S³............................... -1 Torsion or shear -SI - S². S² = O..... O Simple tension SI. SI = SI = 0......... +0.33 Biaxial tension SI = S² S³ - 0......... +0.66 Hydrostatic tension +SI - +S³ = +S³. +1.00 Representation of Strains Strains will be plotted as "true" strains according to the system proposed by Ludwik.1

Jan 1, 1945

By Michael B. Cortie

Mesoporous gold sponge has the unique property of being both metallic and highly resistant to oxidation. It has potential application in catalysis, in bio-sensors, in optical coatings, in analytical chemistry and, as we show here, as the basis for a new kind of ultra-capacitor. Due to the cost of gold, the most probable niche for a gold-based ultra-capacitor would be in the high-power/high-energy regime, a region where gold would compete with devices based on RuO2. A high internal resistance limits the power that can be usefully drawn from existing carbon-based ultra-capacitors, and that this problem can potentially be overcome by gold-based devices. A simple proof-of-concept ultra-capacitor based on mesoporous gold is described and its behaviour during charge and discharge cycles examined. In this work a step change in the input or output voltage of the device was used as the controlling parameter. There was also a residual faradaic current resulting from traces of undissolved aluminium left over from the AuAl2 precursor used to make the sponge, and some charge storage due to polarization of the solution. Deconvolution of these three effects was not entirely accomplished, but an ostensible capacitance of about 7 to 14 mF/g Au was demonstrated. Further improvement from these early results seems likely.

Oct 1, 2003

By H. A. Wheeler

It may surprise some of our members to learn, that, among the industries based on the mineral resources of the United . States, clay now ranks third, being exceeded in value of product only by pig-iron and coal. The present annual value of clay-products exceeds the value of the outputs of gold or silver, and also exceeds the combined values of copper, leacl, zinc, aluminum, mercury, antimony and nickel. These facts are shown in Table I. which gives the statistics for the year 1902 :

Jan 1, 1905

By R. Brough, T. K. Moller

There are differences in design aspects between steel and rubber linings in grinding mills. This paper describes the basic design rules for rubber liners for different grinding applications. When converting a mill from steel to rubber liners, the design must be changed from such familiar steel liner shapes as wedge bars and plates, wave liners, and ship-lap, to take advantage of the characteristics of rubber. Very little of the knowledge of the wear properties of steel can be used for the design of rubber mill liners.

Jan 1, 1990

By William D. Mayercheck

Introduction of continuous mining machines in the late 1940s created a new production bottleneck in room-and-pillar sections-the shuttle car. While continuous miners could cut and load coal at a nearly constant rate, the mining sequence was repeatedly interrupted as fully loaded shuttle cars changed places with empty ones. This wait-for-the-shuttle delay period forced the coal industry to reassess the shuttle's batch-type procedure with an eve toward continuous haulage systems that would allow uninterrupted coal flow from face to portal.

Jan 7, 1979

Clinoptilolite as a Low-Cost Solution to Remove Heavy Metals from Water in Mining and Mineral Processing Industry

Sep 13, 2010

By Steven J. Page

The increasing concern for dust control in metal and nonmetal mining prompted the Bureau of Mines to investigate the dust suppression technique of applying foam to face drilling and crushing operations in a gypsum mine. Previous attempts to achieve effective dust control on face drills using other techniques, such as dry collection and boom-mounted external water sprays, have not been successful. The largest problem encountered when using these techniques has been the lack of sustained effective dust capture at the face. Results for two faces studied show that injection of the foam through the drill steel provided an average dust reduction of 95 pct. However, the use of foam on the crusher provided no dust reduction at the operator's position (because of good local ventilation) and a 27-pct average dust reduction for two feeders at a location midway between the operator's position and the crusher. The conclusions obtained from this study are that (1) foam can be an extremely effective dust control technique when used on localized dust sources such as dust generated within a blasthole during drilling, and (2) foam is only marginally effective as a dust control technique when used on nonlocalized dust sources such as dust generated during the feeder-and-crusher operation.

Jan 1, 1981

By Lawrence Devon Smith

The Business Case for Sustainable Development ?What are SD & TBL? ?Investment Funds & Fund Managers ?Banks and Risk Aversion ?The Dilemma of Juniors ?Meet Your New Partners ?The Cost of Problems ?The Cost of Delays Sustainable Development ?Humanity has the ability to make development sustainable -to ensure that it meets the needs of the present without compromising the ability of future generations to meet their own needs.? Our Common Future BrundtlandCommission, 1987

May 1, 2003

By Wolfgang Pietsch

Pressure agglomeration using tableting machines, roll presses, punch presses, isostatic pressing equipment, extrusion presses, and other less common equipment, represents a large share among commercial applications of size enlargement by agglomeration. The paper attempts to classify and describe the equipment and technology, their development and state of the art, as well as their respective applications, advantages, and disadvantages.

Jan 1, 1977