Search Documents

By Z. T. Bieniawski

In the past 15 years, rock mass classifications have experienced unprecedented development and have emerged as powerful practical methods for assessing ground conditions and tunnel support. Such methods as the RMR System (Geomechanics Classification) and the Q-System have provided many advantages over the classical Terzaghi rock-load method introduced in 1946. These new classifications have found wide applications all over the world but some doubts have been expressed and shortcomings pointed out. The author, who developed the RMR System, takes a penetrating look into the promises and the pitfalls of modern rock mass classifications. He dispels some misconceptions and shows how rock mass classifications can serve as effective and dependable design aids in tunneling.

Jan 1, 1987

By R. C. More O’Ferrall

The author mentions some of the problems he has encountered, together with their solutions. These include the stoping of isolated pillars, the reduction of the size of shaft pillars, the stoping of a new horizon above or below a horizon that has already been stoped out, and the mining of thick bands of reef left behind in the footwall or hanging wall.

Jan 1, 1981

Water retention, water loss and delay in tailings storage rehabilitation are major challenges for many Coal Mines. Work by Stewart, Backer and Busch in the early 1980s suggested that there were improvements to be made in tailings dewatering and density by the addition of flocculant. This prompted ACARP, in cooperation with Bulga Coal Management (Xstrata), to initiate a research project investigating the impact of flocculant addition on tailings deposition density, water retention and the tendency for tailings to form surface crusts suitable for subsequent rehabilitation. A polyacrylamide-based flocculant (200 - 250 g/tds) was injected into the tailings line immediately prior to disposal into the impoundment area. The flocculated slurry rapidly released clear water and created a beach due to the immediate increase in deposition density. The deposition density increased from 35 per cent w/w to 61 per cent w/w solids within 24 hours and continued to increase to 75 per cent, seven days after treatment. The water capture at the tailings storage facility improved by more than 90 per cent; water which would otherwise be lost from the circuit through retention and evaporation. The impoundment capacity had nearly tripled due to the improvement in initial deposition density from 420 kg/m3 up to 1163 kg/m3. Four weeks after disposal surface crusts were forming on the storage facility, suggesting that there would be less delay between cessation and tailings storage rehabilitation.

Jan 1, 2008

By James Douglas

The Copper Queen mine was opened in 1880 by Messrs. Martin, Ballard & Reilly, and the first copper-furnace was blown-in on August 20th of that year. Prior to that summer nothing but prospect-work had been done on the copper Queen and on a number of adjacent claims. In fact, it was a small deposit, not of copper-ore, but of cerussite, which still remains undeveloped, on the western slope of the Queen hill, which

Jan 1, 1900

By Alexander Malahoff

A shipboard research system capable of operating in waters of up to 2,000 m has been designed and implemented by the Hawaii Undersea Research Laboratory (HURL), University of Hawaii. It uses a remotely-operated ocean bottom survey camera system, ROV, bottom TV grab, the PISCES V submersible, and a submersible emergency recovery system aboard the 225-foot RN KA'IMIKAI-O- KANALOA. All systems are operated from the stern of the KA'IMIKAI with a mounted Caley telearm and articulated A-frame system. The system was designed for multi-purpose use of the telearm for launch and recovery of the PISCES V submersible on a lift recovery line (with or without diver assistance), or night-time operations with an electro-optical cable using either the HURL ocean floor sidescan, or photo and video system operated at 10 m above the ocean floor. The 1.14-inch diameter cable is also used to operate the RCV-150 garage/ROV system. The garage/ROV system has also been designed to act as a submersible rescue system with a submersible lift capability.

Jan 1, 1992

A portable surface impedance meter has been tested extensively over a wide variety of geological formations both in Australia and elsewhere. It has proved a useful geophysical too] for relatively shallow mapping (i.e less than 100 metres depth) of faults, intrusions, dykes and conductive ore veins and can be used as a depth probe for overburden and glacial ice. Case studies involving coal seam mapping at Collide (Qld. Australia), galena ore vein location at Zeehan (Tas. Australia) and glacial ice probing on the Brewster Glacier (South Island, New Zealand) are detailed. The first results of a similar unit using a lower frequency with consequential increase in depth of penetration will be presented. The application of VLF measurements to monitor blasting in mines and in the location of earthquake epicentres will also he introduced.

Jan 1, 1987

By Claude Cunningham

Late in 1982 a fire began in the shallow, abandoned workings of the Uitkyk Colliery near Witbank, South Africa. Urgent measures had to be taken to quench the fire, before the surface caving it caused could put an important railroad connection out of action. This paper outlines the way in which the job was tackled.

Jan 1, 1984

By J. D. Miller

Reaction kinetics for gold dissolution in acid thiourea solutions were investigated using formamidine disulfide as an oxidant. For the conditions studied it appears that a surface reaction limits the rate of gold dissolution. The rate was found to be first order with respect to thiourea concentration and half order with respect to the concentration of formamidine disulfide; the apparent activation energy for the reaction was 10.40 kcal/mol (43.40 kJ/mol); and the reaction rate was independent of pH for the pH range 1.0 to 3.0.

Jan 1, 1999

By T Roache, K Yang, M Quigley, C Young

In late 2004 a large-scale evaluation of a new suite of tools for semi-automated core logging was carried out in the Eastern Goldfields of Western Australia. Known as HyLoggingÖ Systems, these combine rapid hyperspectral mapping of mineralogy and very high resolution digital imaging of cores and chips in their original containers. The resulting data is very information-rich and provides information about host rock, alteration and regolith mineralogy. This, in turn, can be used to test geological models about fluid/rock interactions, ore system architecture, ore feed characterisation and generally improve the objectivity of the normally manual and variable logging process. Results were obtained from the Kanowna Belle and St Ives gold deposits in the Kalgoorlie region, as well as numerous holes from across Western Australia stored in the Kalgoorlie Core Library. At the Kanowna Belle gold deposit critical spatial trends in the proportions of white mica, the chemistry and species of those micas, the presence of selected carbonate species and the absence of chlorite proximal to ore zones have all contributed to improved ore deposit understanding. Significantly many of these trends are not discernible to the naked eye, nor easily quantified, previously, across many thousands of metres of core from separate drill holes. At St Ives, the HyLoggerÖ was able to show that low-Al (phengite) and high-Al (paragonite to muscovite) white micas are spatially associated with D3 foliation zones that are proximal and distal to Au mineralisation, respectively. D3 foliation zones are also associated with the depletion of metamorphic chlorite and amphibole, and their replacement with biotite, relative to unaltered mafic host-rocks. The HyLogged GSWA drill holes yielded mineralogical characterisation of classic deposits, including Kambalda (Ni), Fimiston (Au), Teutonic Bore (Cu, Zn, Ag), Black Swan (Ni) and Hannans (Au), illustrating a wide variety of mineralogical trends due to both host lithologies, previously unrecorded lithological subdivisions, and alteration patterns. During 2005 a unique thermal infrared HyLogger was developed to map the important remaining silicates, such as feldspars, quartz, olivines, pyroxenes and garnets. This was successfully tested on a 9000 m subset of the same cores as the earlier study. Interpretation has focused, in particular, on silicification, albitisation, and the mineralogy of several high-grade, less hydrous deposits.

Jan 1, 2006

By H. F. Yancey, O. L. Furse

For several years the Bureau of Mines at its Northwest Experiment Station, in cooperation with the Mines Department. of the University of Washington, has been studying the breakage and degradation of coal. The first phase of the study was devoted to the determination of the friability of many coals of various ranks and comparison of various methods for estimating friability.' A study of the relative ease or difficulty with which various coals are reduced to the fine size required for use as pulverized fuel followed the completion of this work. Baltzer and Hudson2 list twelve research organizations in the United States, two in England, one in Germany and one in Canada that are reported to be engaged on this problem; showing the general appreciation of the need for a simple method of estimating the grindability of different coals. Hardgrove,3 ho has advanced a method for estimating grindability, points out that pulverizer tests of different coals are incomplete and unsatisfactory. He compares such tests to that of a boiler test made without knowledge of the calorific value of the coal. Frisch arid Holder4 also stress the same point. They state that,

Jan 1, 1934

By Mitchell I, Gelfi P, Dunne R, Pyper R

Dump leaching at Teller in its present form began in the fourth quarter of 1988 as an adjunct to milling operations. Initial plans called for a dedicated dump leach facility capable of processing ore at an annual rate of 2.0 million tonnes. Construction of a dump leach pad, collection and process ponds, carbon adsorption system, elution plant as well as reagent addition and ancillary facilities was initiated in mid-1988. During the course of construction, additional reserves were proven. As a result, design throughput was increased to 4.0 Mtpa. Leach pad capacity and solution supply systems were upgraded to handle the larger throughput. However, the carbon adsorption/elution facilities were not upgraded due to space limitations. During 1990 it was decided to expand the dump leach operation to 6.0 Mtpa. Construction of a second leach pad was required which was initiated in early-1991. Plans were again upgraded prior to completion to a target annual throughput of 10.0 million tonnes was. A further two leach pads have been constructed. The first of these being completed during the latter part of 1992. Construction of the latest and largest pad commenced early in 1994.

Jan 1, 1994

By R. Hogg, T. F. Dumm

Procedures for particle size analysis on respirable dust from coal mines have been evaluated. Using respirable dusts dispersed in a laboratory dust chamber, size distributions measured using cascade impactors have been com- pared with the results of a variety of laboratory sizing methods performed on samples collected on filters placed side-by-side with the impactors. The laboratory techniques included centrifugal sedimentation, laser diffraction/scattering and automatic particle counting. The general agreement among the various methods was very good, with systematic differences which can be attributed to the different definitions of size used. Simple conversion factors have been obtained which can be used to transform the laboratory data to equivalent aerodynamic sizes. Similar comparisons have been made on samples collected in underground coal mines. Again, the results are in quite good agreement although small discrepancies were observed in some cases. These have been attributed to some degree of agglomeration in the airborne dust, leading to slightly coarser apparent distributions in the impactor samples.

Jan 1, 1987

By R. H. King

This paper describes the results of an underground coal mine trial installation of a shielded trailing cable. The cable was a three conductor, round, type SHC-GC and was installed on a shuttle car in a conventional room-and-pillar mining section. The purpose of the study was to evaluate proposed legislation that would require shielding on low-voltage trailing cables. Such legislation would require machine modifications to cable reels, packing glands, and couplers; increase cable splicing complexity; and necessitate additional splicing materials and training. Furthermore, fault location might be more difficult. Even though shielding will cause some problems for the mine operator, it can reduce electrical shock hazard to mine workers. This paper presents information that mine operators can use to solve most of the problems encountered if they are required to install shielded cables. The in-mine evaluation was funded by the US Bureau of Mines; however, the views and conclusions in this paper are those of the author and should not be interpreted as necessarily representing official policies of the US government.

Jan 1, 1982

By Jorge Castillo

This paper presents a dynamic analyses of heap leach pad stability under high phreatic levels and various levels of seismic loading. The dynamic analysis were conducted as fully non-linear two dimensional analyses with fully coupled liquefaction triggering using the Fast Lagrangian Analysis of Continua (FLAC) computer code. Also, the geotechnical parameters, appropriate earthquake record selection and modification, model calibration, numerical analyses and results are discussed.

Sep 12, 2005

By Michael J. Sapko, Eugene M. Bazala, Eric S. Weiss, Kenneth L. Cashdollar

The data presented in this report are the results, to date, of an ongoing Pittsburgh Research Center Disaster5Prevention research program on the explosion hazards associated with blasting operations in noncoal mines. Laboratory and experimental mine tests have shown that oil shale and sulfide ore dusts can be ignited given the proper predispersed dust concentrations, particle size, and kerogen or sulfur content. Methane (CH) gas may also4be present in deep oil shale formations and can pose a significant added hazard to underground blasting operations. The most common explosive used for blasting in oil shale had been ANFO, a combination of ammonium nitrate and fuel oil; blasting in sulfide ore had used ANFO and/or dynamites. Tests conducted at the cannon gallery at Lake Lynn Laboratory near Fair chance, Fayette County, PA, provided a means of evaluating the relative incendivity characteristics of new and existing explosive products. Three explosives—a pumpable emulsion-ANFO blend, a packaged water gel, and an emulsion blasting agent—exhibited low-incendive qualities compared with other more highly incendive products such as ANFO and some dynamites. Based on the data collected during numerous full-scale blasts in oil shale and sulfide ore mines, the low-incendive products significantly reduced or eliminated the ignition hazards while at the same time providing effective fragmentation of the rock. Based on the positive results from the gallery and field testing, low-incendive explosives, coupled with good blasting procedures, show promise in reducing dust and/or gas ignitions associated with blasting operations in oil shale and sulfide ore mining applications.

By Robert L. Lagace

This final report documents the work dune by Arthur D. Little, Inc. (ADL) on behalf of the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center (PMSRC), on Contract H0122026 (which began in August of 1971). Under this contract ADL provided technical assistance to the Bureau on a task basis on virtually all aspects of the Bureau's programs related to present and planned emergency and operational communications and miner location systems for underground coal mines. The work consisted of independent investigations, analyses, experiments, breadboard and prototype hardware development, workshops and technology transfer seminars on mine communications, and on-going evaluations and guidance related to the Bureau's contracted programs on electromagnetic noise, mine communications systems, and trapped miner location. This final report documents the work in two volumes, Volume I, "Emergency and Operational Mine Communications," and Volume II, "Seismic Detection and Location of Isolated Miners." The Tables of Contents of both Volumes are included in each Volume. Phase I of the contract was devoted to performing an in-depth assessment of electromagnetic noise measurements taken by several contractors and other investigators, and then defining a new noise measurement program and instrumentation system tailored to obtain the necessary but missing noise data. These data are required for use in the design of new emergency and operational communication systems. This work, and the follow-on coordination and guidance activities of ADL on this noise measurement program in subsequent phases of the contract, are treated in Part One of Volume I.

Jan 1, 1974

By P. H. Lu, M. J. DeMarco, J. R. Koehler

Beginning in late 1985 and continuing through 1987, US Bureau of Mines personnel investigated longwall chain pillar and entry design in two and three-entry gateroad systems at a deep underground coal mine in central Utah. To evaluate their respective stability characteristics, four chain pillars and two longwall panels within the two separate entry systems were instrumented with Bureau hydraulic borehole pressure cells to continuously monitor vertical and horizontal pillar and panel stresses through adjacent panel retreat. In addition, supplemental entry closure information was obtained from sites located in the vicinity of the instrumented pillars. The findings presented in this report demonstrate the practicality of evaluating mine pillar stability using in situ methods and support three significant conclusions regarding ground control aspects of the investigated two-entry system: (1) Total areal entry loading was considerably less for the two-entry system, as opposed to the three-entry system, (2) a smaller percentage of opened ground in the two-entry system contributed to a marked reduction in rooffalls, and (3) lower areal loading in the two-entry system suggests improved ground conditions when mining the underlying seam.

Jan 1, 1987

By Kenneth R. Sites

Under this program two tape recording and triggering systems were developed and delivered for use in the Bureau of Mines microseismic program. The systems are designed to improve the effectiveness of the Bureau owned Sangamo 3500 series and SABRE VI instrumentation tape recorders. The system is designed to capture random microseismic data, digitize and temporarily store these data, start the tape recorder; and then transfer the data to magnetic tape for permanent storage. The system is designed to pack data on tape such that the tape may be simply played back through galvo drivers onto an oscillograph such that a continuous series of analog records, with corresponding time of day information, are reproduced without excessive oscillograph paper waste or the need for the operator to search for valid events.

Jan 1, 1980

By N Green

The production of approximately 550 000 tonnes of æwhiteÆ or chrysotile asbestos fibre between 1972 and 1983 at the Woodsreef Mine in New South Wales left behind 24 million tonnes of tailings and 75 million tonnes of waste rock and overburden. The Woodsreef Magnesium Project is designed to extract the 23 per cent magnesium content of the tailings to produce magnesium metal and magnesium alloys, the latter with aluminium from the New South Wales smelters. Further value will be added to the tailings waste with the downstream production of magnesium alloy sheets and cast products for the transportation, electronics and other consumer goods industries. The mine opened in 1918 and closed in 1983 becoming derelict. There has been minimal expenditure on rehabilitation compared with that recommended in reports commissioned by the New South Wales Government. The tailings dump has been designated æasbestos wasteÆ by the EPA and will be eliminated through the magnesium refinery process of the Project with the dissolution of the remaining chrysotile fibres. The benign waste from the refinery process will consist principally of silica with some iron. Significant energy savings are expected from innovative new processing technology, in the alloy formation and in the application of the light weight, cast and sheet metal products, particularly in the transportation industries. Globally, there are very large resources of similar tailings with hundreds of years of useful productive lives that could be converted into the metal of the 21st Century, magnesium, and its alloys, to assist pollution and greenhouse gas reduction from transportation industries. No new mining and minimal feedstock preparation is required. Unlike potential producers using carbonate rocks such as magnesite and dolomite that have to be mined, the asbestos tailings composed principally of non-fibrous serpentinite do not contain any carbon dioxide.

Jan 1, 2002

By William A. Vogely

HIGH ACTIVITY, continuing the substantial recovery from the slump of 1954, characterized the domestic nonfuels-mining industries during 1956 Income generated in producing nonfuel minerals and mineral products3 increased 9 percent over 1955 as compared with a 6-percent increase for all industries. Thus, the 1956 performance of the mineral industries, while not as dramatic as the 27-percent increase obtained in 1955, continued to exceed the gains of the total economy. Other measures of mineral activity strengthen this conclusion. The index of physical volume of mineral production, presented for the first time as an integral part of this review, reflects significant gains in all major sectors during 1956; and, although the overall increase was diminished somewhat by the steel and iron-ore strike in July 1956, the all-mineral index (including fuels) reached a new high.

Jan 1, 1958