Search Documents

By Randhir S. Sehgal

After some decades of lying low and being treated as a second rate fuel, coal is back in the news. Production is rising. Predictions are for an ever expanding use, and they differ only in their rates of increase. Even the FBI is involved in trying to stop fraudulent sales of non-existent coal lands and leases to the innocent. In short, we have a nearly chaotic boom on our hands. Obviously our energy production base is in the process of undergoing a major shift, and the process will present many problems. However, there is little doubt that the industry has the basic strength and organization to be able to deal with the new issues that will arise as a result of these shifts in production and use of coal. After all, it does produce nearly 800 M tpy now, and coal is the single biggest fuel for generation of electricity. This role of coal is illustrated in the table below, which shows the coal equivalent quantities of various fuels used in the production of electricity.

Jan 1, 1980

By John L. Miles

John L. Miles (Arthur D. Little, 1nc.)—Pollack and orris" have reported measurements on electron tunneling through A1-A12O3-A1 sandwiches in which the oxide was formed by gaseous oxidation in a glow discharge. From these measurements they deduced the asymmetry of the barrier and, since this is small, conclude that the mechanism suggested by Mott19 for the growth of oxide in thin A12O3 films is inapplicable. In earlier papers20 Pollack and Morris report similar work for oxide films grown thermally. In this case they find a greater asymmetry and conclude that the Mott mechanism is valid. I would like to point out that both these conclusions are quite unjustified. Mott suggests that the growth of the oxide film on aluminum results from the passage of ions through the already present film of oxide under the action of an electric field. This field results from a constant voltage which is in effect a contact potential between metal on one side of the barrier and adsorbed oxygen ions on the other side of the barrier. The theory does not require that the oxide grown is nonuniform either in stoichiometry or structure. It does however specifically assume that the partial layer of ionized oxygen on the surface remains adsorbed on the surface of the growing oxide. In other words, the so-called "built-in field" remains in the oxide only as long as the ionized oxygen is present. When a counter electrode of aluminum is deposited on the oxide, it will react with the adsorbed oxygen on the surface of the oxide, thus forming a small additional amount of oxide. It is clear, then, that there is no requirement in the Mott theory of oxide growth which would necessitate tunneling currents through an Al-A1203-A1 sample to be different when the polarity is reversed. Neither does the theory eliminate the possibility that some additional mechanism could cause the tunneling barrier to be asymmetric and hence tunneling currents to be a function of polarity in such a sandwich. Thus these tunneling-currents measurements are not germane to the question of whether the Mott mechanism is the true method of growth of aluminum oxide films. In fact, it is not surprising that there should be a difference between the oxide properties at the two interfaces (with resulting asymmetry in the tunneling barrier) since the growth conditions and growth rates must have been quite different at these two positions. S. R. Pollack and C. E. Morris (authors' reply)— The point raised by Miles above is one has caused some confusion in the past. The following is an attempt to clarify this point. The built-in field which is responsible for the growth of the thermal oxide at low temperatures arises, according to Mott, because of the passage of electrons from the Fermi surface of the oxidizing metal to surface states introduced by the adsorbed oxygen. It is assumed that the energy of these surface states lies below the Fermi energy of the metal. Electrons therefore continue to flow from the metal to the surface until the built-in electric field raises the potential energy of the surface states to the value of the Fermi energy in the metal, at which time equilibrium is obtained between the surface states and the metal. That is in equilibrium as many excess electrons pass from the metal to the surface per unit time as vice versa. The surface of the oxide prior to deposition of a metallic counterelectrode can then be pictured as follows. The Fermi energy lies in the energy gap of the oxide and is essentially pinned at the energy of the oxygen surface states. The vacuum work function of the oxide is then given by the sum of the electron affinity of the oxide (i.e., the difference in energy between the vacuum and the conduction-band minimum) plus the energy difference between the conduction-band minimum and the Fermi energy. The deposition of a metal onto the surface of the oxide can result in a transfer of electrons across the extremely thin oxide only if there is a contact potential difference between the deposited metal and the parent metal or oxide. That is if the vacuum work function of the deposited metal differs from that of the parent metal, then charge can be redistributed across the oxide in order to equilibriate the Fermi energy across the structure. (It should be

Jan 1, 1965

By David L. Sikarskie

The measurement of residual stress fields using X-ray diffraction techniques requires the removal of successive layers of material from the specimen. In the process of removing these layers, the underlying residual stress field is altered; hence, if the original stress field is desired, corrections must be made to the measured stresses. Although these corrections already exist for a number of cases, an alternate procedure is outlined herein whereby the corrections are presented in series form. This form is numerically more convenient within certain ranges of correction depths and in its simplicity gives additional insight into the factors affecting the corrections. It, further, readily permits determining the proper slice depth to remove and the effect on the correction of both specimen thickness and magnitude and form of the measured residual stress itself. ONE of the techniques currently being used to determine residual stress fields is X-ray diffraction. Since X-rays are diffracted essentially from the layers of atoms near the surface of the specimen, of the order of 0.0001 to 0.001 in. depending on conditions, the method can only determine stresses* in this very thin surface region. Therefore, if the residual stress field at some depth into the specimen is required it is necessary to remove successive layers of material taking measurements after each cut. In the process of removing a thin surface layer of stressed material, however, the over-all equilibrium of a cross section of the specimen is disturbed with the result that the internal residual stress which existed before the slice of material was removed is altered. This alteration of stress occurs after each slice and its effect is cumulative. Thus, if the original stress distribution is desired, corrections must be applied to the measured stresses. These corrections can be found by satisfying equilibrium on each new cross section. These corrections have been derived in detail for a number of cases, e.g., cylinders, bars, plates,' and also are given in Appendix VI of Ref. 2. In each of the above cases the correction terms require the evaluation of definite integrals of the measured residual stress distribution. In general, this is indeed the way one would proceed with the corrections. There are a number of instances, however, where the integrals can be replaced by a series form of correction which is considerably more convenient numerically and, also, gives added insight into the factors which influence the corrections. Such a form of the correction is particularly useful, for example, if one is interested in designing a test such that stress corrections will be small. Also, the question of what depth of slice to use in relation to both specimen thickness and residual stress distribution itself must invariably be answered. Questions of this type can be readily answered using a series form of correction. In addition, if the correct residual stress distribution is needed only for limited depths into the specimen the series correction provides numerical results which are equivalent to the integral correction. I) DERIVATION OF THE SERIES CORRECTION The problem to be considered here is that of a bar or plate,* i.e., either one or two dimensions of the specimen is large compared with the third. Also, the residual stress distributions considered depend only on z, see Fig. 1. In view of this it can be shown' that a stress correction, based on simple beam theory, satisfies all conditions of "elasticity theory" and hence is the correct (and only) solution. The integral form of the correction (this assumes that the measured residual stress is a piecewise continuous function) as given in Ref. 1 is:

Jan 1, 1968

By F. J. Martin, W. G. Hubler

The Beattie mine is at about the center of Duparquet township in the Province of Quebec, Canada. It is 22 miles northwest of the town of Noranda. The elevation is approximately 1200 ft. above sea level. This locality, long considered a favorable one from the geological point of view, has been prospected for over 20 years, but no discoveries of economic importance were made until the present orebody was found by John Beattie in 1930. The specific gravity of the ore is 2.77. The gold occurs in intimate association with the sulfides, pyrite and arsenopyrite, which in turn are very finely disseminated in a silicified porphyry. The bulk of the gold is associated with the pyrite, only a small proportion being with the arsenopyrite. There are small amounts of magnetite, ilmenite and chalcopyrite present in the ore. There is also some hematite in the ore that is mined from near the surface in the open pit. Metallurgical Problems and Methods or Attack 1. The ore is extremely hard and resistant to grinding. 2. The sulfide minerals are finely disseminated in the gangue. 3. The gold, in turn, is so intimately associated with the sulfides that grinding to even 5 microns will not release all of the values for cyanidation. 4. It is necessary to make a high ratio of concentration in order to obtain a product sufficiently high in gold to meet high shipping and treatment charges. Hardness of the Ore.—Owing to the extreme resistance of the ore to grinding, it was recognized that grinding costs would be high. Microscopic tests showed that grinding to 95 per cent minus 325 mesh would be necessary to liberate a sufficient amount of the values in order to obtain a tailing assaying 0.02 oz. gold per ton, which is considered to have the economical minimum gold content that can be obtained. It is not feasible to grind this hard low-grade ore (0.18 to 0.20 oz.) to 95 per cent minus 325 mesh, so it was necessary to overcome the problem in another way. The following method was decided upon: (1) Fine crushing to minus 1/4 in.; (2) relatively coarse primary grinding; flotation of low-grade concentrates in the primary and rougher circuits and discarding the

Jan 1, 1935

With the exeption of the United States, Canada and Russia, oil has not been around in quantity near world centres of population. Production: in Western Europe is insignificant. Japan is without production as are Australia, Southern Africa, India; Brazil, Chile, New Zealand and China. The United States is, however, a large importer of crude oil. The very fact that oil is produced generally away from centres of population means that it has to be carried by sea to the area in which it is required. There is, therefore, a constant flow of oil around the world in very definite channels.

Jan 1, 1962

By Tong Qin, Jinxia Zhang, Fusheng Niu, Limei Bai

"The interaction between a deformable bubble and a rigid particle in viscous liquids under microgravity conditions is studied by direct numerical simulation via an Arbitrary-Lagrangian-Eulerian (ALE) method. Due to the microgravity, the bubble will stay as a sphere in the fluid without external forces and its deformation is caused by the moving particle. In this study we assume the flow field is axisymmetric and the motion of the gas inside the bubble is neglected. The particle equations and the Navier-Stokes equations for the fluid are solved in a unified finite element framework. The particle obtains an impact velocity by an external force and the impact velocity is varied over a wide range. A ‘critical time scale’ T0 was identified for the interaction process. For successful contacts between particle and bubble, the time scale of their relative motion must be less than T0.INTRODUCTIONThe particle-bubble interaction is an important process in many applied industrial domains such as water treatment, froth flotation and liquid steel purification. It is a complex three phase process in that it embraces many research areas: fluid hydrodynamics, interfacial forces, particle and bubble behaviour and solution chemistry.Derjaguin and Dukhin(1961) clarified the particle-bubble interaction by introducing three-zone model for small and medium size particles. When the particle is far away from the bubble surface, the hydrodynamic forces are dominant. The particle is driven toward the bubble surface by the particle inertial and gravity. This region is regarded as Zone 1 and the interaction in this zone is a collision subprocess. As the particle gets close to the bubble, it exits a zone where the liquid flow around the bubble surface creates a tangential stream from the upper surface of the bubble toward the rear of the bubble. This is Zone 2 which is called the diffusiophoretic zone. In Zone 3, the particle is very closed to the bubble, surface forces like van der Waals, electrostatic and structural forces are considered. Contrast to Zone 1, Zone3 can be regarded as an attachment subprocess."

Jan 1, 2016

By L. A. Panek

When rock is subjected to a load it is deformed. Ordinarily this is observed in a mine as the displacement of one point with respect to another-the deflection of the roof, which may be observed as a convergence between roof and floor; or the extrusion of material from the rib, which may be observed as a decrease of the distance between the rib and the post of a timber set. The effect of excessive pressure may be a rockburst if the rock is strong, or it may be "squeezing" ground if the rock is "soft". Some desirable effects of high stress (high in relation to strength) are the caving of roof in a longwall mining operation, the caving of ore in block caving, and the decrease in mechanical energy required to break down the mineral seam in a retreating pillar-robbing operation. In any case, whether the observable effect of rock load is desirable or undesirable, it is a displacement, and depends on the following four factors:

Jan 3, 1961

By Charles Mabery

So FAR as the elementary composition of petroleum is -known, it may be briefly stated. Petroleum consists principally of a few series of hydrocarbons, with admixtures of sulfur, nitrogen, and oxygen derivatives in comparatively minute proportions, which may be regarded as impurities to be removed in the preparation Of commercial products. But as each series is represented by many homologs, in the aggregate, crude petroleum is an extremely complex mixture of hydrocarbons and their derivatives. In part, these hydrocarbons individually conform in structure to the system of synthetic hydrocarbons whose structure is well defined and -represented by the typical series CnH2n+2, CnH2n, the series CnH2n-2, CnH2n-4, the members of which have not been sufficiently studied to establish their structure, and the series CnH2n-6 composed of the aromatic group, benzene and its homologs. Hydrocarbons of greater density contained in the portions of petroleum that cannot be distilled without decomposition doubtless have less hydrogen than is represented by these formulas. Since to every hydrocarbon there is a definite temperature, even in vacuum, at which its constituent carbon and hydrogen atoms fall apart, and since for the heavier bodies this temperature is not much above 360° C. in vacuum, it is evident that some other method than distillation must be devised for their separation if anything further is to be learned concerning their individual constitution. CLASSIFICATION OF PETROLEUMS There is such a wide variation in the composition of petroleum from different fields, it would seem possible to make a classification on this basis were it not that no single variety is entirely free from hydrocarbons contained in others. Such a classification has been suggested of the exceptionally pure Pennsylvania petroleum, the sulfur oil from Trenton

Jan 2, 1920

By Charles Trotter

AN instrument has recently been developed for determining the inclination and azimuthal direction of boreholes. This instrument is known as the Tro-Pari Instrument and is the invention of C. Trotter and G. Pajari of Sudbury, Ontario. DESCRIPTION The instrument is characterized by a unit mounted in gimbals and provided with a clockwork mechanism to clamp a compass to indicate azimuthal direction and simultaneously to clamp the unit in its plumb position to indicate inclination (Fig I). By means of a timing ring suitably calibrated in 5-min divisions, the unit may be set to lock after a lapse of time sufficient to allow the placing of the instrument at the desired point in the drill hole where readings are to be taken. The maximum time lapse obtainable with the instrument designed for use in EX or AX size holes is 1 hr 30 min which is considered to be ample time to lower to the greatest depths that may be drilled with this size of equipment. Larger sizes could be developed for larger diameter holes such as BX and NX sizes or the larger oil-well sizes and a correspondingly greater time lapse could be provided for. Up to the present time only the EX-AX size has been built. OPERATION Assuming a borehole is to be surveyed at 1000-ft depth and assuming it will take 30 min to lower the instrument to this depth, the timing ring is rotated through seven divisions which represent a time lapse of 35 min (5-min leeway) and is then returned to its zero position. This operation imparts energy to a spring which drives the clockwork mechanism. Simultaneously the compass needle is freed to swing to its magnetic north-south position and the encased mechanism is freed to hang plumb within a semicircular portion of the frame which is graduated in degrees after the fashion of a protractor. This semicircular protractor portion has a V-shaped notch at each degree division of its inner periphery. The instrument, now in its free position, is inserted in a bronze container made to suit the size of hole to be surveyed (Fig 2). Soft rubber washers are provided within the container to prevent undue shock. The container is connected to the drill rods with three 5-ft lengths of brass or aluminum alloy rods separating it from the steel rods in order to prevent distortion of the magnetic field. The assembly is then lowered to the desired point where readings are to be taken and is allowed to remain at rest until a period of time has elapsed slightly in excess of the time for which the timing ring was set. In the example cited above, when the 35 min has elapsed the compass needle is locked in its north-south position and the protractor locking pin is extruded and locks in the V notch opposite its plumb position. The device may now be removed from the borehole and it will remain in this locked position in spite of jarring or shak-

Jan 1, 1947

By Charles Trotter

An instrument has recently been developed for determining the inclination and azimuthal direction of boreholes. This instrument is known as the Tro-Pari Instrument and is the invention of C. Trotter and G. Pajari of Sudbury, Ontario. Description The instrument is characterized by a unit mounted in gimbals and provided with a clockwork mechanism to clamp a compass to indicate azimuthal direction and simultaneously to clamp the unit in its plumb position to indicate inclination (Fig I). By means of a timing ring suitably calibrated in 5-min divisions, the unit may be set to lock after a lapse of time sufficient to allow the placing of the instrument at the desired point in the drill hole where readings are to be taken. The maximum time Lapse obtainable with the instrument designed for use in EX or AX size holes is I hr 30 min which is considered to be ample time to lower to the greatest depths that may be drilled with this size of equipment. Larger sizes could be developed for larger diameter holes such as BX and NX sizes or the larger oil-well sizes and a correspondingly greater time lapse could be provided for. Up to the present time only the EX-AX size has been built. Operation Assuming a borehole is to be surveyed at 1000-ft depth and assuming it will take 30 min to lower the instrument to this depth, the timing ring is rotated through seven divisions which represent a time lapse of 35 min (5-min leeway) and is then returned to its zero position. This operation imparts energy to a spring which drives the clockwork mechanism. Simultaneously the compass needle is freed to swing to its magnetic north-south position and the encased mechanism is freed to hang plumb within a semicircular portion of the frame which is graduated in degrees after the fashion of a protractor. This semicircular protractor portion has a V-shaped notch at each degree division of its inner periphery. The instrument, now in its free position, is inserted in a bronze container made to suit the size of hole to be surveyed (Fig 2). Soft rubber washers are provided within the container to prevent undue shock. The container is connected to the drill rods with three 5-ft lengths of brass or aluminum alloy rods separating it from the steel rods in order to prevent distortion of the magnetic field. The assembly is then lowered to the desired point where readings are to be taken and is allowed to remain at rest until a period of time has elapsed slightly in excess of the time for which the timing ring was set. In the example cited above, when the 35 min has elapsed the compass needle is locked in its north-south position and the protractor locking pin is extruded and locks in the V notch opposite its plumb position. The device may now be removed from the borehole and it will remain in this locked position in spite of jarring or shak-

Jan 1, 1949

By D. Perry, G. W. Binkley, G. K. Dumbauld, F. A. Brooks

A new cementing technique has been developed which is particularly applicable to permanent-type well completion operations. The technique makes use of the accelerating effect of calcium chloride on setting time and strength development of cement cake deposited in squeeze cementing. An unique feature is that the accelerator is applied after the unaccelera-ted cement slurry has been squeezed and the excess has been reversed from the well. Laboratory data on the accelerating effect of calcium chloride applied to the fi1ter cakes of three low-water-loss cementing compositions demorzstrate that the procedure results in relatively rapid development of strength and impermeability of the cement cake. Simulated squeeze-ceinenting tests made in the laboratory likewise corroborated the practicality of the procedure. The laboratory tests showed that a newly developed oil-emulsion cemerzting composition is more susceptible to acceleration of set than are modified cements containing high percentages of bentonite. The acceleration procedure has been used successfully in field operations. INTRODUCTION Nature of Problem In squeeze-cementing operations, a substantial amount of time is consumed in waiting on the cement to develop strength after it has been squeezed into the well. Frequently, an interval of 18 to 24 hours or longer is required for the development of strength sufficient to prevent failure of the cement during subsequent operations in the well. Reduction of this waiting-on-cement time offers appreciable savings both in time and in money. A particular type of squeeze-cementing operation to which an increasing amount of attention has been given is encountered in permanent-type well completion operations wherein perforations are to be squeezed off1. In this procedure, it is customary to pump the cement slurry down the tubing and out into the perforated section through a retractable extension pipe. Squeeze pressure is then applied, which forces the cement slurry into the perforations and causes the build up of a compact filter cake of cement within the perforations. The excess slurry remaining in the hole is then removed by reverse circulation. The extension pipe is then retracted, and, if a new interval is to be perforated, a perforating gun is run through the tubing. The newly perforated interval may then be tested by swabbing. In such operations, it has been customary to allow approximately 20 hours or so for hardening of the cement squeezed into the perforations. This time interval is usually measured from the time that the cement is reversed out of the hole to the time that subsequent swabbing is started. If the cement has not developed strength at the commencement of swabbing, the pressure differential caused by swabbing results in failure of the squeeze job. At the time that the work described in this report was initiated, particular consideration was given to the reduction of waiting-on-cement time in squeeze cementing by the permanent-type completion technique. Consequently, much of the experimental work was directed to this specific objective, though the process which was developed for acceleration of strength development has possible application in other than permanent-type completion operations. Method of Attack Although quick-setting cements

Jan 1, 1957

By Dick Lewis

The Misima deposit is on Misima Island in the Lousaide Archipelago, 240 km east-southeast of the Papua New Guinea mainland, and 600 km east of Port Morseby. Misima is a narrow mountainous island 40 km long and up to 10 km wide. The highest point is 1035 m above sea level. Gold mineralization is restricted to the eastern and less rugged third of the island. The Melanesian population lives in coastal villages. Subsistence agriculture is the main activity, although copra and cocoa are grown in plantations on the eastern and southern coasts. Prior to 1950, mining was important in the economy of the island. Climate is tropical, with little seasonal variation in temperature or rainfall. Tropical cyclones occur about every 10 years (Fig. 1).

Jan 1, 1990

By R. S. Handy

DOES hand-sorting of mill feed pay? The fact that the practice is so general would seem to indicate that there must be good reasons for following it; yet, to my mind, the advantage in many cases is doubtful enough to invite a thorough discussion of the subject, in an effort to determine under what conditions hand-sorting does pay. A typical sorting plant in the Coeur d'Alene district handles about 800 tons of mine-run ore per day. The material is run over a grizzly with about 4-in. opening; the oversize is crushed to about 4-in. size and joins the undersize, and the whole product is washed and screened on trommels with about 1 ½ -in. openings. The oversize from these trommels is spread on a belt and the waste and first-class ore are sorted out by hand, the residue being further crushed, and passes, together with the trommel undersize, into the mill feed bins. About 50 tons of shipping ore and 150 tons of waste are sorted out per day, leaving about 600 tons of mill feed. To sort out this material requires 20 ore sorters and five bosses and repairmen. The normal cost of hand-sorting is about 16 c. per ton of run-of-mine ore, or 65 c. per ton of material sorted out. I believe that straight crushing and milling of the run-of-mine ore, in this case, is not only cheaper, but is metallurgically moree canonical and efficient than hand-sorting followed by milling of the residue. At one of the Bunker Hill rock-houses, 1250 tons of run-of-mine ore are reduced to pass 30-mm., or about 1 ¼ -in. opening in six hours, requiring five men. The equipment and the power consumed are not greatly different from that required in a sorting plant of the same capacity, and the normal cost of thus preparing the feed for milling is under 3 c. per ton of mine product. The relative cheapness of this method as against hand-sorting is thus clearly established, the saving being about 13 c. per ton. If there is any virtue in hand-sorting, then, it must lie in the metallurgical results achieved.

Jan 4, 1918

By Roald Ysteboe, Finn Olesen

"Elkem has developed a process that utilizes SPL as a raw material for pig iron production. This process will be demonstrated in industrial scale during 2008 and 2009. The process developed produce iron, and the reduction material used, is the carbon present in the SPL. The iron source could be either virgin iron ore or waste/recycled material from the steel industry. The SPLrefractory and bath material is dissolved in the slag produced. The slag is designed so that any leaching of environmentally dangerous elements is minimized. This process can in addition to SPL, consume other types of waste derived from the primary production of aluminium. Elkem intends to supply this demo project with SPL and other waste products from external sources, domestic as well as international ones.IntroductionSpent Pot Lining (SPL) is generated when an electrolytic cell for producing aluminium is taken out of service and the refractory and carbon lining is removed from the steel potshell.The yearly generation of SPL world wide is exceeding 500 000 tonnes. The major amount of this quantity is stockpiled or land filled, unprocessed.SPL contain large amount of water soluble fluorides and some amount of cyanides and is classified as hazardous waste in most countries."

Jan 1, 2008

By Richard A. Kesler, W. Michael Reed

Grindability or resistance to fine comminution is the fundamental issue involved in the application and sizing of grinding mills. Over the years, many theories for determining the amount of energy required for size reduction to a specified fineness have been proposed. The first published theory, introduced by P. R. von Rittinger in 1867, stated that the energy required for crushing or grinding is proportional to the increase in surface area produced. The surface area of a ton of particles of diameter (d) is proportional to (1/d), therefore the work input per ton for particles of diameter (d) would be proportional to (1/d). The second significant theory is that of F. Kick published in 1885. Kick said that the work required is proportional to the reduction in volume of the particles concerned. If (f) is the diameter of the feed particles and (p) is the diameter of the product particles, the work input relationship would be: [W =Ioq(f/p) 9] The "Third Theory" of F.C. Bond, introduced in 1951, states that the work required is proportional to the length of the new crack tips produced in particle breakage during crushing or grinding and equals work represented by the product minus that represented by the feed. This takes the form: [W=]

Jan 1, 1982

By Walter Rose

It is the purpose of this note to call attention to the circumstance complicating the attainment of uniform gas-liquid distributions in multi-phase flow systems, and especially in those of the so-called Hassler type.' Although the complication arises directly as a consequence of gas compressibility and the dependence of fluid distributions on interfacial curvature phenomena, little reference to the problem has yet appeared in the literature.' In fact, it is only the paper of Geffen et al.3 which gives any experimental evidence that a problem exists. On the other hand, previous authorsl,4,5 have made the tacit, albeit fallaceous assumption that uniform gas-liquid distributions automatically are established in linear flow systems by the expedient of maintaining the pressure gradients equal in the flowing gas and liquid phases. Such a device, it can be shown, will succeed only if the immiscible fluids are both equally compressible or both essentially non-compressible. Another necessary condition required before uniform fluid-fluid distributions can be achieved is that the porous matrix is isotropic. Uniform fluid saturation distribution conditions obtain in isotropic media only when the curvature of each interface of contact between wetting and non-wetting fluids is everywhere the same throughout the interspaces. This is a necessary condition which follows from the consideration that variation in interfacial curvature gives rise to finite capillary pressure gradients and therefore to variation in the saturation distribution. That this is not a sufficient condition follows from the consideration that hysteric possibilities allow for different saturations even though the capillary pressure gradient is zero. In any event, it will- be recalled that it is the intent in the Hassler scheme of relative permeability determination' to obtain initially (by the capillary pressure drainage or imhibition process) uniform conditions of fluid distribution in the core sample, and then to maintain this uniformity during mixture flow so that the resultant fluid mobilities which are calculated will refer to steady-state transfer under fixed conditions of uniform saturation. If the flowing fluids are incompressible, it is recognized that employment of the same value of the pressure gradient in each fluid will result in maintenance of the initially obtained condition of zero capillary pressure gradient. On the other hand, the consequence of gas compressibility is that the gradient in the gas pressure varies from point to point in the flowing stream. and since the pressure gradient in an incompressible liquid is constant it is thus impossible to maintain zero capillary pressure gradient during the simultaneous flow of gas-liquid mixtures. Therefore, one would expect to observe a variation in the gas-liquid saturation in the directions of the capillary pressure gradients, depending in magnitude on the particular way saturation changed with capillary pressure. In order to formulate the manner gas compressibility effects prevent the attainment of uniform gas-liquid distributions during mixture flow, consider a linear flow system of unit length. As noted, it is necessary to assume an isotropic medium (viz. one where permeability is independent of position and direction). One then can arbitrarily set the pressure

Jan 1, 1951

By Walter Rose

It is the purpose of this note to call attention to the circumstance complicating the attainment of uniform gas-liquid distributions in multi-phase flow systems, and especially in those of the so-called Hassler type.' Although the complication arises directly as a consequence of gas compressibility and the dependence of fluid distributions on interfacial curvature phenomena, little reference to the problem has yet appeared in the literature.' In fact, it is only the paper of Geffen et al.3 which gives any experimental evidence that a problem exists. On the other hand, previous authorsl,4,5 have made the tacit, albeit fallaceous assumption that uniform gas-liquid distributions automatically are established in linear flow systems by the expedient of maintaining the pressure gradients equal in the flowing gas and liquid phases. Such a device, it can be shown, will succeed only if the immiscible fluids are both equally compressible or both essentially non-compressible. Another necessary condition required before uniform fluid-fluid distributions can be achieved is that the porous matrix is isotropic. Uniform fluid saturation distribution conditions obtain in isotropic media only when the curvature of each interface of contact between wetting and non-wetting fluids is everywhere the same throughout the interspaces. This is a necessary condition which follows from the consideration that variation in interfacial curvature gives rise to finite capillary pressure gradients and therefore to variation in the saturation distribution. That this is not a sufficient condition follows from the consideration that hysteric possibilities allow for different saturations even though the capillary pressure gradient is zero. In any event, it will- be recalled that it is the intent in the Hassler scheme of relative permeability determination' to obtain initially (by the capillary pressure drainage or imhibition process) uniform conditions of fluid distribution in the core sample, and then to maintain this uniformity during mixture flow so that the resultant fluid mobilities which are calculated will refer to steady-state transfer under fixed conditions of uniform saturation. If the flowing fluids are incompressible, it is recognized that employment of the same value of the pressure gradient in each fluid will result in maintenance of the initially obtained condition of zero capillary pressure gradient. On the other hand, the consequence of gas compressibility is that the gradient in the gas pressure varies from point to point in the flowing stream. and since the pressure gradient in an incompressible liquid is constant it is thus impossible to maintain zero capillary pressure gradient during the simultaneous flow of gas-liquid mixtures. Therefore, one would expect to observe a variation in the gas-liquid saturation in the directions of the capillary pressure gradients, depending in magnitude on the particular way saturation changed with capillary pressure. In order to formulate the manner gas compressibility effects prevent the attainment of uniform gas-liquid distributions during mixture flow, consider a linear flow system of unit length. As noted, it is necessary to assume an isotropic medium (viz. one where permeability is independent of position and direction). One then can arbitrarily set the pressure

Jan 1, 1951

By Tuncel M. Yegulalp, Malcolm T. Wane

In general, many problems relating to the exploitation of mineral deposits are probabilistic in nature. This derives from the fact that the geologic universe is inherently random. Probability theory and statistics have been found useful for forecasting the behavior of natural events that occur in the geologic universe. The objective of this paper is to outline the application of the theory of extremes to this forecasting problem. Consider the design of an underground structure or the design of a rock slope. The initial step is the formulation of the various possible structural actions which result from the geometry of the layout. For a given structural model, various intensities of behavior are possible depending upon the load, deformation, and material characteristic spectra, respectively. Of popular interest to mining people is the failure behavior or condition. A necessary feature of the analysis is the rupture strength of the material. Information on the rupture strength is derived from testing either in situ or in the laboratory and the usual outcome is a variation in the test results. This variation is overcome by constructing a frequency distribution of rupture strengths, and then determining a measure of central tendency and variability. The main feature of interest in the analysis is the failure characteristic and its percentage chance of occurrence. Hence, one is naturally led to examine those areas of a distribution curve which are termed the tails. The statistical concepts which can most efficiently handle such areas are contained within extreme value statistics.

Jan 8, 1969

By Walter L. Maxson, Fred C. Bond

THIS paper is a continuation of two earlier papers, l, 2 and presents new data on the grindability of various ores and other materials-the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a new method of measuring the "surface energy" of an ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems. 1. GRINDABILITY OF VARIOUS ORES This part is a continuation of the paper listed as reference No. 1. The method of testing is described in detail in that paper. The sample to be tested is crushed to all through 6 mesh in rolls set at x6-in. opening in closed circuit with a screen. Of this sample 700 C.C. is ground dry in a laboratory ball mill under constant conditions of mill speed and ball charge in closed circuit with a screen of the desired size at 250 per cent circulating load. The mill is cylindrical, 12 by 12 in., and rotates at 70 r.p.m. It contains a charge of 285 iron balls weighing 20,125 grams and ranging from 1 ½ to ¾ in. in diameter. Each test is continued for a sufficient number of periods to establish equilibrium at 250 per cent circulating load, or until the composition of the circulating load is constant for successive periods. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the results are expressed as the net production in grams of screen undersize per revolution of the mill. This is designated as the

Jan 1, 1938

By Fred C. Bond and

This paper is a continuation of two earlier papers,12 and presents new data on the grindability of various ores and other materials—the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a new method of measuring the "surface energy" of an ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems. 1. GRindability of Various Ores This part is a continuation of the paper listed as reference No. 1. The method of testing is described in detail in that paper. The sample to be tested is crushed to all through 6 mesh in rolls set at 1/16-in. opening in closed circuit with a screen. Of this sample 700 C.C. is ground dry in a laboratory ball mill under constant conditions of mill speed and ball charge in closed circuit with a screen of the desired size at 250 per cent circulating load. The mill is cylindrical, 12 by 12 in., and rotates at 70 r.p.m. It contains a charge of 285 iron balls weighing 20,125 grams and ranging from 1½ to ¾ in. in diameter. Each test is continued for a sufficient number of periods to establish equilibrium at 250 per cent circulating load, or until the composition of the circulating load is constant for successive periods. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the results are expressed as the net production in grams of screen undersize per revolution of the mill. This is designated as the

Jan 1, 1939