Search Documents

By E. G. Leonardon, C. Schlumberger, M. Schlumberger

The object of this paper is to describe the adaptation of electrical resistivity measurements to the particular case of exploration in which the surface is an expanse of water (river, lake, sea). Water in itself does not constitute an obstacle to electrical exploration. It is merely an overburden, which is fluid instead of being solid, and as a consequence the routine of the measurements has to be modified. Also, in many instances, the liquid under consideration is highly conductive (salt water). This introduces an additional difficulty into exploration work, and has to be overcome by the geophysicist. We do not propose to discuss here the basic principles of electrical resistivity measurements, which have been dealt with in various previous papers,' but will simply recall the two fundamental techniques which govern its field application: 1. Horizontal exploration, or method of the resistivity map, in which a series of electrical measurements are carried out at various stations, keeping the same electrode spacing. Thus, a horizontal layer of the subsoil, of a practically constant thickness, is explored. 2. Vertical exploration, or "vertical sounding"2 method, in which a seriesr of measurements is made with increasing electrode spacings at one or several stations. In this way, the apparent resistivity is determined at a given station for various increasing thicknesses of the ground.

Jan 1, 1934

By J. D. Forrester, Erich Sarapuu, T. C. Cheasley

John G. Tripp-—The concept of converting fuel deposits in-situ to useful forms of energy and chemical raw materials has important possibilities as a means of stretching out our fuel resources. The authors have worked in this field for years and in fact are among the pioneers in developing in-situ techniques based on underground electrocarbonization. Their efforts have aroused great interest in this subject and their contributions will undoubtedly gain even more significance as time goes on. The 4 to 5 billion tons of petroleum are proved reserves, that is, they are completely defined and could be produced economically with present methods of recovery. Reserves of coal, tar sands, and oil shale shown in Table I are not equivalent to proved reserves as the term is used in the oil industry. Incidentally, the 4.3 billion tons of oil shown in the tabulation is equal to about 28 billion barrels of oil and, therefore, presumably does not include reserves of natural gas liquids estimated at about 5 billion barrels. The relative comparisons would be more complete if these liquids together with the reserves of natural gas were included in the tabulation. It is stated in the report that production costs of the order of 10c per million Btu's could be expected from a large industrial electrocarbonization installation. The authors state that the operation probably could be operated successfully and at a profit. I would like to express my view that for the operation to be profitable extremely favorable conditions would have to prevail. For example, the coal seam would have to be thick and close to the surface in order to minimize drilling costs; the deposit should be dry and so situated that there would be little, if any, inflow of ground water; and the seam would have to be relatively gas tight to avoid excessive gas leakage. Notwithstanding the tremendous strides that have already been made, it is my hope that the authors plan to continue their development work. Experiments on underground electrolinking and initial carbonization at Gorgas, Ala., indicate a need for improved control over the operation. Subsequent examination of the underground system at Gorgas has shown that the gasification zone did not always follow a direct path between the electrodes. Undoubtedly the control of the in-situ thermal processes can be improved by further development work. With respect to the electrocarbonization of oil shale it may be well to point out that the cost of mining oil shale is estimated to be 50c to 60c per ton. These are low mining costs as compared to coal. Thus it would appear that there is less economic incentive for applying in-situ thermal methods to oil shale than there is for applying these methods to coal. As is the case with in-situ methods for petroleum, the product from the shale having the most economic interest would be liquid oil rather than gas. The authors point out that for distances up to several hundred miles it is cheaper to transmit energy as electricity than it is to ship energy as coal. This is a very important point, and with coal shipping rates rising periodically, it could prove increasingly important in the future. I believe that the authors deserve great credit for their outstanding work on underground electrocarbonization. The knowledge resulting from their efforts is of great value to our fuels technology. James L. Elder—The experimental work conducted by the authors on the electrolinking-carbonization of carbonaceous materials in situ is of great interest. The method is of great importance in the development

Jan 1, 1955

By Zhang Wei

"Pulang Copper Mine is located in Shangri-La county, Diqing Prefecture, Yunnan Province, with currently defined copper reserve of 4.8 million tonnes of copper metal and an average grade of 0.34% Cu. The mineralized zone in a dome shape is 2,300 m long, 600–800 m wide, and 1,000 m high. At present, the project is at a construction phase, with a first-stage mining and processing capacity of 12.5 million tonnes of ore per year. Ore haulage is planned via a drift and ore pass development system. The cavability of mineralized rock is classified into three types (II, III, IV), with type III accounting for more than 98% of the total reserves. The cavability of the orebody is generally considered to be good and block caving mining method is planned. Semi-autogenous grinding and ball milling are adopted for the mineral processing. The tailing dam construction method is a center-line method.INTRODUCTIONAs the China's largest underground nonferrous mine, Pulang Copper Mine is located in the northeast of Shangri-La County, Diqing Prefecture, Yunnan Province, China. It is 62 km northeast of Shangri-La city. Shangri-La County is a Tibetan-dominated, multiple-ethnic region, with a population of approximately 163,000 in 2009. The county is rich in mineral and water resources, thriving with tourism. Its economy is also dominated by agriculture. To date, the defined copper reserves at the Pulang Copper Mine is 4.8 million tonnes of copper metal at an average grade of 0.34% Cu. In addition, it contains a gold reserve of 145 tonnes, a silver reserve of 2,754 tonnes, a molybdenum reserve of 0.19 million tonnes, and a sulphur reserve of 10.5 million tonnes. The first-stage mining and processing capacity is planned at 12.5 million tonnes of ore per year. When it ramps up to this production rate, the mine will produce copper concentrate containing 50,000 tonnes of copper and molybdenum concentrate containing 968 tonnes of molybdenum. A drift and ore pass system is planned for ore haulage and mining method is a block caving method. Semi-autogenous grinding and ball milling are considered for mineral processing. A center line dam is adopted for the tailing dam construction (Feng, 2010; Feng, Li, & Wang, 2011; China Enfi Engineering Corporation, 2014)."

Jan 1, 2016

By E. C. Hopkinson, A. H. Youmans, R. A. Bergan, H. I. Oshry

A new log has been developed for quantitative formation evaluation which is based on a measurement of the length of time slow neutrons survive before they are captured in the rocks and fluids. The logging instrument employs a cyclically pulsed neutron generator and a gated scintillation counter which is synchronized with the source. The source emits short, intense bursts of 14 mev neutrons once every 1,000 microsec and is quiescent between bursts. During the period the source is quiescent, the detector is electronically actuated for two independent preselected intervals. A comparison of the counting rates during these two intervals gives a measure of the rate of decay of the slow neutrons and of the associated gamma radiation. The average neutron lifetime in most earth formations is in the range from 50 to 500 microsec. It can be measured during a continuous logging operation at conventional logging speeds. The design of the logging instrument is described and the results of tests are compared with theoretical predictiom. Formulas are developed which give the relationship between log response and formation properties. It is shown that the method is particularly sensitive to formation fluid salinity, and that salt water saturation can be measured accurately in either cased or open hole. The measurement can be made independent of borehole size, fluid type, casing and tool position in the hole by properly selecting the intervals during which the measurements are made. The results of tests with a prototype logging tool are given. INTRODUCTION A new nuclear logging system has been developed which employs the Accelatron,* an accelerator-type neutron source, and accurately measures formation brine saturation in an entirely new way. It has produced a type of formation log with better sensitivity, greater sampling depth and simpler quantitative interpretation than any other nuclear log thus far suggested. The new Neutron Lifetime Log* employs a pulsed electromechanical neutron source and a synchronously gated radiation detector. A prototype instrument has been field tested during recent months to demonstrate the operability of the apparatus and the feasibility of the method. Tests in wells and simulated boreholes have confirmed theoretical predictions and have shown that formation param ters can be measured independent of casing and other borehole parameters. Preliminary results of field tests have indicated that the log may have important and widespread applications. BASIC PRINCIPLE OF NEUTRON LIFETIME LOG The Neutron Lifetime Log is based on the fact that neutrons emitted by a source in a well are rapidly but not instantly captured by the material around the source. Their capture is a matter of statistical probability; the greater the number of capturing nuclei and the greater the "capture cross section", the greater is the probability that a neutron will be captured quickly. The average life of a thermal neutron in vacuum is about 13 minutes, but in common earth materials, the average neutron life ranges between extremes of about 5 rnicrosec for rock salt and perhaps 900 microsec for quartzite. The Neutron Lifetime Log responds to variations in this average neutron life. The theoretical basis for a log of this general type has been well understood by nuclear logging experts in many laboratories both in America and in Russia, and develop mental work along these lines has been in progress for many years. The Russian literature has reported both theoretical and experimental work1,2 but in this country there have been no published reports of progress toward a practical logging instrument. The logging instrument is designed to measure radiation produced by slow neutrons during selected intervals when no neutrons are being emitted by the source. The source is arranged to emit neutrons in bursts or pulses. During the quiescent interval between the pulses, it is possible to observe the exponential "decay" of the neutrons and the neutron-induced radiation as the individual neutrons progressively disappear due to capture by atoms in the formation or the borehole. When a short pulse of 14 mev neutrons is emitted by a source in a borehole, the individual neutrons are slowed to thermal energy within a few microsec. Thus, a cloud of "slow" neutrons is formed around the source within 10 to 50 microsec after the pulse. This cloud is most dense within a few inches of the source, and is progressively less dense out to a radius of about 3 ft, where radiation from the source is practically undetectable.

Jan 1, 1965

By A.A. Gustafson

In diamond or churn drilling for the prospecting of ore bodies, two products can be used for quantitative analyses; i.e., the core and the cuttings, or sludge. Some operators prefer an assay of core; others insist that the sludge be sent for analysis. Both must recover the sludge for check samples or for assays if there is no core recovery for any particular section of the diamond-drill hole. The Freeport Sulphur Co. found that numerous cumbersome sludge boxes or barrels were inconvenient and delayed drilling. The sludge settled slowly in the ordinary shallow, rectangular diamond-drill boxes and its total removal from the container was difficult, time-consuming and unsatisfactory; and sampling of deposits of which the metal contents are easily concentrated, as in ores containing cinnabar, gold and silver, is subject to error if the boxes are not thoroughly cleaned. Mr. Charles Ballard, dredge superintendent at Freeport's operation at Grande Ecaille, Louisiana, developed a portable cone while he was in charge of prospecting a mercury property near Tonopah, Nevada, in 1940. Ballard later improved the design while the settler was being used at a manganese property in New Mexico. The operation is based on the "free settling" of comminuted particles in a quiescent liquid. The ordinary sludge box discharges over a lip 8 to 12 in. wide and consequently the water has sufficient velocity so that the discharge water is never clear. The cone settler used by Free-port Sulphur Co. discharges over the entire circumference, which gives a discharge ltp of 9 ft. in the size of cone used at the cinnabar and manganese prospects. Consequently, the velocity of the discharge water is slow enough so that all fine material settles and the discharge water is clear. When the drilling of a sample interval is complete, the sludge can be drawn off by the time the driller is ready to cut another sample. Thus, only one cone is needed per drill. The cone has been used by Freeport successfully in churn-drilling a manganese deposit, in diamond-drilling a mercury deposit, and in diamond-drilling a deposit of ore containing tin, copper, gold and silver. The cone is greatly superior to the old methods of collecting sludge and is now used on all Freeport drilling campaigns in the western states, both for surface and underground drilling. Fig. I shows the important details of a cone designed for average operating conditions, 30 in. in diameter and 36 in. high. Abnormal conditions may require some revisions in design. Fig. 2 shows a working drawing. A hose or pipe larger than the one used to convey water from the pump to the swivel head of the string of rods is connected to the stuffing box at the collar of a diamond-drill hole, The usual T-connection is used. It is not necessary to use a stuffing box if the top of the cone can be placed lower than the collar of the hole. Then the return water and cuttings can be made to flow by gravity. This hose or pipe discharges the cuttings of the drill bit and the return

Jan 1, 1943

By A. A. Gustafson

IN diamond or churn drilling for the prospecting of ore bodies, two products can be used for quantitative analyses; i.e., the core and the cuttings, or sludge. Some operators prefer an assay of core; others insist that the sludge be sent for analysis. Both must recover the sludge for check samples or for assays if there is no core recovery for any particular section of the diamond-drill hole. The Freeport Sulphur Co. found that numerous cumbersome sludge boxes or barrels were inconvenient and delayed drilling. The sludge settled slowly in the ordinary shallow, rectangular diamond-drill boxes and its total removal from the container was difficult, time-consuming and unsatisfactory; and sampling of deposits of which the metal contents are easily concentrated, as in ores containing cinnabar, gold and silver, is subject to error if the boxes are not thoroughly cleaned. Mr. Charles Ballard, dredge superintendent at Freeport's operation at Grande Ecaille, Louisiana, developed a portable cone while he was in charge of prospecting a mercury property near Tonopah, Nevada, in 1040. Ballard later improved the design while the settler was being used at a manganese property in New Mexico. The operation is based on the "free settling" of comminuted particles in a quiescent liquid. The ordinary sludge box discharges over a lip 8 to 12 in. wide and consequently the water has sufficient velocity so that the discharge water is never clear. The cone settler used by Freeport Sulphur Co. discharges over the entire circumference, which gives a discharge lip of 9 ft. in the size of cone used at the cinnabar and manganese prospects. Consequently, the velocity of the discharge water is slow enough so that all fine material settles and the discharge water is clear. When the drilling of a sample interval is complete, the sludge can be drawn off by the time the driller is ready to cut another sample. Thus, only one cone is needed per drill. The cone has been used by Freeport successfully in churn-drilling a manganese deposit, in diamond-drilling a mercury deposit, and in diamond-drilling a deposit of ore containing tin, copper, gold and silver. The cone is greatly superior to the old methods of collecting sludge and is now used on all Freeport drilling campaigns in the western states, both for surface and underground drilling. Fig. I shows the important details of a cone designed for average operating conditions, 30 in. in diameter and 36 in. high. Abnormal conditions may require some revisions in design. Fig. 2 shows a working drawing. A hose or pipe larger than the one used to convey water from the pump to the swivel head of the string of rods is connected to the stuffing box at the collar of a diamond-drill hole. The usual T-connection is used. It is not necessary to use a stuffing box if the top of the cone can be placed lower than the collar of the hole. Then the return water and cuttings can be made to flow by gravity. This hose or pipe discharges the cuttings of the drill bit and the return

Jan 1, 1943

By A. A. Gustafson

In diamond or churn drilling for the prospecting of ore bodies, two products can be used for quantitative analyses; i.e., the core and the cuttings, or sludge. Some operators prefer an assay of core; others insist that the sludge be sent for analysis. Both must recover the sludge for check samples or for assays if there is no core recovery for any particular section of the diamond-drill hole. The Freeport Sulphur Co. found that numerous cumbersome sludge boxes or barrels were inconvenient and delayed drilling. The sludge settled slowly in the ordinary shallow, rectangular diamond-drill boxes and its total removal from the container was difficult, time-consuming and unsatisfactory; and sampling of deposits of which the metal contents are easily concentrated, as in ores containing cinnabar, gold and silver, is subject to error if the boxes are not thoroughly cleaned. Mr. Charles Ballard, dredge superintendent at Freeport's operation at Grande Ecaille, Louisiana, developed a portable cone while he was in charge of prospecting a mercury property near Tonopah, Nevada, in 1940. Ballard later improved the design while the settler was being used at a manganese property in New Mexico. The operation is based on the "free settling" of comminuted particles in a quiescent liquid. The ordinary sludge box discharges over a lip 8 to 12 in. wide and consequently the water has sufficient velocity so that the discharge water is never clear. The cone settler used by Free-port Sulphur Co. discharges over the entire circumference, which gives a discharge ltp of 9 ft. in the size of cone used at the cinnabar and manganese prospects. Consequently, the velocity of the discharge water is slow enough so that all fine material settles and the discharge water is clear. When the drilling of a sample interval is complete, the sludge can be drawn off by the time the driller is ready to cut another sample. Thus, only one cone is needed per drill. The cone has been used by Freeport successfully in churn-drilling a manganese deposit, in diamond-drilling a mercury deposit, and in diamond-drilling a deposit of ore containing tin, copper, gold and silver. The cone is greatly superior to the old methods of collecting sludge and is now used on all Freeport drilling campaigns in the western states, both for surface and underground drilling. Fig. I shows the important details of a cone designed for average operating conditions, 30 in. in diameter and 36 in. high. Abnormal conditions may require some revisions in design. Fig. 2 shows a working drawing. A hose or pipe larger than the one used to convey water from the pump to the swivel head of the string of rods is connected to the stuffing box at the collar of a diamond-drill hole, The usual T-connection is used. It is not necessary to use a stuffing box if the top of the cone can be placed lower than the collar of the hole. Then the return water and cuttings can be made to flow by gravity. This hose or pipe discharges the cuttings of the drill bit and the return

Jan 1, 1943

Assure fail-safe stopping of a mining vehicle immediately following a loss of electric power. Approach A separate emergency brake system which actuates when electrical power is interrupted, was installed on several mining vehicles and tested in a long-term underground mining demonstration. How It Works Separate, spring-actuated brakes, which press against brake discs, are used to stop the vehicle following power failure. To allow norm al movement of the vehicle, hydraulic oil under pres? sure from the vehicle's hydraulic system is directed to a spring? loaded piston in each emergency brake housing. That pressure causes the piston to compress the spring and relieves the spring pressure against the puck, thereby allowing the brake disc to turn freely. See Figure 1 A. If the electrical power fails or if the machine is turned off, a valve in the hydraulic line to the emergency brakes opens. That valve, shown as ?Solenoid Valve (automatic)" in Figure 1, which is normally held closed by its electrical solenoid while the vehicle is electrically powered, is opened by the spring in the valve assembly. The pressure in the hydraulic line which is connected to the emergency brakes then drops to

Jan 1, 1978

By K. Schonert

Jigging is a separtion process that has already been described by Agricola in 1556. Fine size material is normally treated in a hutch jigging process, in which the heavy particles are penetrating the jigging bed and are recovered in the hutch. In this process, a ragging consisting of the same or higher specific gravity particles is inserted upon the screen. The ragging is used mainly as a valve to maintain a constant upward flow of the water. Since the heavy particles should pass easily into the hutch, the ragging particles are up to ten times larger than the maximum feed size (1). In the fine size range - 1 mm the performance of jigs is mainly insufficient; some of the low density particles percolate the ragging while the hutch water flow prevents the fine heavy particles from entering the bed (2). By giving a thin layer of particles, which posesses a density sensitivity in case of certain adjustment of flow conditions, directly on the screen, the precision of separation can be increased. Stroke length and frequency have to be adjusted to give this filter layer a homogenous porosity between 60 and 70% during the pulsion phase, and the "en masse" lifting of the bed, as it is known in jigging of coarser material, has to be prevented (3). In this case, the jig cycle is only of minor influence.

Jan 1, 1987

By E. D. Glass, R. C. Hessing

The volume of gas in storage reservoirs may be compuled from estimates of hydrocarbon pore volume and gas density. However, both are dificult 10 estimate accurrately. Further, no adequate method has been presented for estimating reservoir performance during operation for Volumetric gas-storage reservoirs. Normally, gas-storage reservoirs exhibit small pressure gradients in the area conr(zilliitg the storage wells, even under conditions of maximum injection or withdrawal. A zone of low permeability usally surrounds, and is in communication with, tile permeable zone which causes the storage reservoir to exhibit a definite pressure lag, as evidenced by lack of pressure stabilization after extended periods of shut-in. An analysis is presented for determining pore volume and gas in place, and for predicting future reservoir behavior of such reservoirs. The mathematical development is presented and a solution is shown for an operating storage reservoir. INTRODUCTION Depleted gas reservoirs arc often used for gas storage. The reservoir usually contains a permeable area in which numerous storage wells arc located. The permeable zone permits high deliverability and injectivity with relatively small pressure loss. However, pressure equilibrium may not be attained even after long periods of shut-in because of the fact that the permeable zone is in communication with an adjacent tight section. Most of these gas-storage reservoirs are sand lenses, such as ancient beaches or offshore bars. The areal geometry of these reservoirs is normally such that flow in the tight zone will be approximately linear, and the solutions presented here should apply. DISCUSSION For purposes of this paper, a gas-storage reservoir is considered to consist of a volume of permeable rock in communication with tight rock, all of which is surrounded by an impermeable barrier. Pressure gradients across the permeable zone are small due to low flow resistance and well density. Hence, the permeable zone is considered to be at a uniform pressure which is only a function of time as gas is injected or withdrawn. The tight zone is considered to be linear with uniform permeability and porosity, and the pressure in the tight zone is a function of both position and time. l'wo solutions for flow in this system are used to define the reservoir and determine its properties. The first solution is for an infinite linear tight zone in communication with the permeable zone. The expression for constant gas-withdrawal rate is Eqs. I and 2 ore superposed to account for varying rates of production or injection and are used to fit gas-storage field reservoir history. The solution for the infinite case, Eq. 1, is first applied to field data for early times following a shut-in period. Constants BDa and c are ohtained by a least-squares fit of pressure and rate data. After the pressure wave from gas injection or withdrawal reaches the external boundary of the tight zone, the infinite solution will no longer apply and pressure behavior should be more nearly represented by Eq. 2 for a gas reservoir in communication with a finite linear tight zone. The values of the constants found from curve-fitting Eq. 1 to the early time data may then be used in Eq. 2 that only the coefficient- L containing the unknown

This volume summarizes characteristics and the geological setting of porphyry copper deposits of the Western Hemisphere. Grouped by characteristics, porphyry copper deposits are described in six regions: Andean orogen, Appalachian orogen, Alaska, northern Cordilleran orogen, southern Cordilleran orogen, and the Caribbean. Each region has its own peculiarities of geologic setting, and those deposit characteristics that may be projected from one chapter to another will be used in reaching the conclusions from which to draw genetic models for porphyry copper deposits. The term porphyry in this volume denotes a type of ore deposit, rather than a rock classification. The classification of intrusive igneous rocks used in this volume is shown in Figs. 36a and 42 (pp. 103, 130). Some modern classifications suggest mineral-ratio definitions other than those used in this volume; however, most literature references cited are based on the classification shown in Figs. 36a and 42. The reader should be aware, therefore, that quartz monzonite in this volume contains from 35% to 65% potassuim feldspar and at least 10% quartz. A term used in this volume is defined where introduced within the context of a specific chapter. Distensional tectonic conditions are used in the sense of Cady (1972) in the Appalachian orogen, for example. Porphyry copper deposits are defined as large bodies of mineralized rock, usually including a porphyritic intrusive phase, that have copper sulfide minerals disseminated through them. The definition has no commercial connotation and is used strictly in a noneconomic sense to encompass the spectrum of copper mineralization associated with these deposits. Terms commonly accepted in the literature are not defined. Porphyry molybdenum and porphyry copper deposits commonly are distinguished by most economic geologists. The basis for the separation is summarized in one chapter of this volume. To permit the reader to more easily peruse the bibliography for any particular region, references will be found at the end of each chapter. The bibliography is not intended to be complete, but is designed to provide adequate minimum coverage for descriptions of deposits in the chapter concerned. Each entry is properly referenced in the text of that chapter to facilitate the reader's research into any particular topic. This volume is written from the point of view of the exploration geologist whose task it is to evaluate the structural, petrographic, mineralogic, and metallogenic characteristics of a porphyry copper deposit. The goal of the evaluation is to determine if, and where, concentrations of metals may exist in an igneous- hydrothermal system that includes the most complex set of geologic factors found in any of the many types of ore deposits. The successful porphyry copper geologist is simultaneously a petrographer, geochemist, structural geologist, and mineralogist. Some porphyry copper deposits have developed in volcanic arcs underlain by a Benioff seismic zone with a trench paralleling the arc. The most convincing example of a deposit known to have developed in an environment where subduction is an active process is the 3.3 m.y. (million years) old Dry Creek occurrence in the Aleutian arc (this volume). On the other hand, the younger deposits in the Cascades appear to have formed in a volcanic arc lacking both the Benioff zone and the offshore trench. Subduction is not widely accepted as an active mechanism for the period when the younger Cascade deposits formed. Subduction has also been questioned for deposits formed at a great distance from a plate boundary (e.g., Bingham). Regardless of the pros and cons regarding subduction, most deposits are associated with regional faults. Strike-slip

Jan 1, 1978

By Thomas L. Kesler

Essentially all of the barite produced in Georgia has come from the Carters-ville district in the northwest part of the state. The earliest recorded shipment of ore, 60 tons, was made in 1894.' With the exception of the four-year period 1931 to 1934, the separate yearly output has been recorded and published since 1915, whereas the total yearly output of the United States has been published since 1880. The separately recorded production of Georgia (Cartersville) through 1947 is 2,232,544 short tons valued at $14,900,746,2 but unpublished data on the period 1931 to 1934, plus the estimated unrecorded output prior to 1915, make the actual total about 2,400,000 short tons. This is about 21 pct of the total production of the United States, which, through 1947, is 11,328,440 short tons valued at $71,683,386.2 The barite-producing part of the Cartersville district is relatively small, having from north to south a length of 4.5 miles, and a width of 2 miles. This small area, containing 35 barite mines, is the source of practically all of the barite produced in the state. The area is hilly, and has a total relief of 500 ft. The west-flowing Etowah River crosses the middle of the area, and is an unfailing source of water for operations on properties near its course. Opencut mining is carried on during the entire year, but is hampered by rain in the winter and early spring. Three railroads, two U.S. highways, and a network of graded roads provide access to and within the district, as well as excellent shipping facilities for ore and supplies. In addition to the barite, the district contains deposits of manganese, brown iron, ocher, umber, and specular hematite. Geologic Setting The area containing the barite deposits is underlain by Lower Cambrian rocks and their weathered residua. These rocks are grouped in three formations; in ascending order, these are the Weisner, the Shady, and the Rome. The Weisner formation consists mainly of finely micaceous metashale containing many random beds of quartzite, a few beds of conglomerate and metasiltstone, and beds of crystalline limestone that is apparently scarce. The formation is more than 1000 ft thick, and the base is not exposed. On account of their resistance to weathering, the rocks of the Weisner formation have sustained the higher elevations and therefore crop out on the ridges that characterize the area. Nearly all of these ridges are underlain by asymmetric anticlinal folds, and conversely the intervening valleys are underlain by synclinal folds. A diagrammatic section, showing typical mode of exposure of the Weisner rocks and their relation to overlying formations, in the limb of a fold, is shown in Fig 1. The Shady formation here consists of a lithologically distinctive series of variably siliceous specular hematite beds and thin beds of dolomite, which in places contain abundant fossils. In the zone of weathering, the dolomite has been leached and most of the hematite hydrated to ocherous and umber-ous clays, hut bedding planes in these weathered materials are commonly well preserved with or without distortion effected by slumping. This preservation of structure during weathering is lacking in the residuum that rests on the Rome dolomite, which is described below. The maximum thickness of the

Jan 1, 1950

By M. D. G. Salamon

In view of an urgent need for a simple means of simulating the behaviour of stratified rock masses, a long-dormant linear model is revived, generalized, and discussed in some depth. The model is piecewise homogeneous, consisting of a pile of homogeneous isotropic laminae in which the interfaces between beds are parallel and free of shear stresses and cohesion. The continuity of stresses and normal displacements is assured across the bedding planes and, to maintain simplicity, the theory of thin plates is used as the kernel of the model. The paper covers the case where the rock mass consists of discrete beds in which the layers are arranged either heterogeneously or systematically. The stratification is regarded as uniform when all the layers are of the same thickness and their Young's modulus changes exponentially with depth; and as homogeneous when all the laminae have identical thickness and properties. The case of uniform stratification is also treated on the basis of an equivalent quasi-continuum derived from the basic model. Attention is focused on the derivation of influence functions. It is demonstrated that the quasi-continuous models, when they are available, can replace their distinct-layer counterparts. The homogeneous quasi-continuum, which permits the derivation of its influence functions in closed form, facilitates the determination of the roof and floor convergence. In the case of a significant class of problems, the convergence distribution is defined by a second-order differential equation in the xy plane, which simplifies to a Poisson's equation if the mining excavations are unsupported. With this result, the paper prepares for the solution of a host of practical problems. These solutions are presented in a series of papers that are in the course of publication.

Jan 1, 1991

By J. Philip Neal, Carroll P. Rogers

Feldspars, the most abundant minerals of the igneous rocks, occur in numerous forms and mixtures. The feldspars of commercial significance are found in widely distributed pegmatites as large crystals usually free of iron- bearing impurities and thus suitable for hand-cobbing, and also in larger bodies where the ore contains various types of feldspar inter- mingled with quartz and relatively free of iron- bearing impurities, or at least readily unlocked from impurities present at relatively coarse mesh. The latter type of ore includes some pegmatites, and the ''alaskite" bodies so common in the Spruce Pine district of North Carolina. On the west coast of the U.S. and in Oklahoma there is-r has been--commercial recovery of natural feldspathic sand as a source of alumina in glass and ceramics. "Aplite" in commercial terminology is a light-colored igneous rock with a granitic composition and a fine sugary texture, often banded with readily removable iron impurities. Two areas in Virginia produce aplite for the glass industry: one located in the vicinity of Piney River, Amherst County, and the other near Montpelier in Hanover County. According to Deer et al. (1966) the word feldspar derives from the Swedish feldt or falt (field) and "spath:" chunks of rock appearing in tilled ground overlying granite. Castle and Gillson (1960) indicate a Germanic origin, citing "spat," which is said to refer to any transparent or translucent material which is readily cleavable. The term "spar" has in the past been applied to minerals other than feld- spar, such as barite, calcite, and fluorite. It is correct to call the latter "fluorspar." There is a true barium feldspar, but it is rare and of no present economic importance. What is recognized as feldspar or "spar" by present producers and consumers consists of three silicate minerals which, if pure, would have the formu- las KAISi,O, (microcline or orthoclase), NaAlSi,O, (albite), and CaAl,Si,O, (anorthite). These are almost never found in pure form in nature, but occur together in great abundance in a three-component system. A considerable number of different combined ratios of these three exists, with the exception that isomorphism between potassium spar and calcium spar is very limited. User specifications for feldspar products are largely built around the prevalent naturally occurring ratios. Pas- sages following will refer to "K-spar," "Na- spar," or "Ca-spar." Nomenclature and Descriptive Terms Relating to both the mineralogy and the economics of feldspar are certain terms whose coverage it is useful to specify. Commercially, aplite is a feldspathic rock mined and beneficiated in two locations in Virginia, in which both titanium and feldspar minerals are present-the latter now being the major, if not the only, economic product. Technically, the term aplite when applied to this rock is of questionable accuracy. But, in light of accepted commercial usage, the term will be here used to designate it. Regarding the Virginia rock, Ross (1941) is cited.

Jan 1, 1975

By F. Lombard

We consider in this paper the use of a modified version of Hotelling?s statistic in the analysis of particle size distributions. The statistic can be adversely affected by the presence of outliers among the data. We propose a competitor to the statistic that is based on ranks, and hence is less sensitive to outlier effects. The results of a Monte Carlo study suggest that the rank test is highly competitive with the Hotelling test in its ability to detect differences between two mass size distributions. The calculation of the rank statistic is explained in detail and its application is illustrated on two sets of data.

Jan 1, 2012

By F. Lombard

We consider in this paper the use of a modified version of Hotelling?s statistic in the analysis of particle size distributions. The statistic can be adversely affected by the presence of outliers among the data. We propose a competitor to the statistic that is based on ranks, and hence is less sensitive to outlier effects. The results of a Monte Carlo study suggest that the rank test is highly competitive with the Hotelling test in its ability to detect differences between two mass size distributions. The calculation of the rank statistic is explained in detail and its application is illustrated on two sets of data.

Jan 1, 2012

By Osamu Fukuta

The geological and geochemical characteristics of the Japanese iodine-rich brines are outlined. The iodine-rich brine in Japan is primary in its origin and its occurrence is limited in the younger marine sediments. The iodine-rich subsurface water is saturated or over- saturated by natural gas, but the water saturated by natural gas is not always rich in iodine. The iodide and bromide contents decrease with time. The bromide content decreases much more rapidly than that of iodide. It should be emphasized that the genetic environment of the Japanese type of dissolved gas and iodine deposit is not peculiar to the Japanese islands.

Jan 1, 1985

By P Lilly

Blasting is the primary comminution process in most mining operations. This process involves the highly complex and dynamic interaction between two main components. The first is the detonating explosive and the second is the rock mass into which the explosive is loaded. The mechanical properties of the rock material (such as dynamic strength, tensile strength, dynamic modulus and fracture toughness) are important considerations in understanding the blasting process. However, it is the characteristics of the geological defects (joints, foliation planes, bedding planes) within the rock mass that ultimately determine how effectively a blast performs in terms of fragmentation, all else being equal. The defect characteristics include, but are not limited to, their orientation, spacing, and mechanical properties. During the blasting process, some of the geotechnical characteristics of the rock mass are substantially changed. From the blasting outcome point of view, the most notable and important is the change in fragment size distribution that the rock mass undergoes. The pre-blast in situ defect-bounded block size distribution is transformed into the post-blast muckpile fragment size distribution. Consequently, it is fundamental to our understanding of and ability to predict the blasting process that both the blastability of a rock mass and its transformation into the fragment size distribution can be appropriately quantified.

Jan 1, 2001

Winzes are usually sunk 9 ft. 6 in. long by 6 ft. 0 in. wide and are divided into two compartments, 4 ft. 0 in. by 5 ft. 0 in. inside the timbers. The general practice is to sink the winze to a depth of from 9 to 12 ft., put in bearers and three or four rings of timber, and then erect a sinking headframe before continuing sinking operations.GENERALThe main feature governing the design of the headframe was that all parts could be transported on timber trolleys in No. 2 Shaft. Except for some minor details the structural members consist of steam pipe. Joints are sections of steam pipe welded to one member and into which the other member fits and is held in place by a 1-in. bolt. The headframe consists essentially of two bedpieces to carry the winch and to form a seat for the four legs. The legs support the sheave bearers, the tipping door and the brace.Except during tipping operations the door is in a nearly vertical position. For tipping it is lowered to an inclined position and a hook suspended from one of the bracing members of the headframe is attached to a "D" welded to the bottom of the kibble. This causes the kibble to tip when it is lowered on to the tipping door. The capacity of the kibble is 4 cubic feet.THE HEADFRAMEThe dimensions of the headframe are:Height to top of sheave .. .. 14 ft. 10 in.Distance centre to centre of legs 4 ft. 4 in.Length of bedpieces .. .. .. .. 8 ft. 9 in.The weight is approximately 2,000 lb., the tipping door and bedpieces being the heaviest members. They weigh 240 lb. and 170 lb. respectively.One compartment of the winze is decked over, and the bedpieces, which are 8 ft. 9 in. lengths of 6 in. pipe with three short lengths of plate welded to the underside, are placed over the sinking compartment, either transversely or parallel to the winze. Three 3 inch pipes act as spreaders between them.Welded to the top of each bedpiece is a 6-in. by iHn. plate 3 ft. 0 in. long with four 4-in. by 1.5-in. slots cut longitudinally at 10 in. centres. Two 10 in. by 4-in. timbers are bolted to these plates, the distance between them being adjusted to suit the holes in the winch bedplate, which is bolted to the 10-in. by 4-in. timbers.Two short lengths of 3 in. pipe are welded to each bedpiece at 4 ft. 4 in. centres. These form the seats for the legs of the headframe, which are...

Jan 1, 1941

By A. S. Ericson, J. H. Corrigan, E. J. Jahnsen

Calcine is transported from the Reduction Plant at 850°C in insulated hopper cars and charged into three rectangular electric melting furnaces each equipped with three - 18.5 MVA transformers. The electrical energy is applied through six in line prebaked carbon electrodes, and slag and metal are tapped at opposite ends of the furnaces on an intermittent basis. The slag, 5000 tonnes per day, is disposed of by a pot train directly to the dump. The ferronickel, 250 tonnes per day, is tapped into 40 tonne capacity ladles in which it is refined in two ASEA-SKF ladle furnace stations. Casting is done over lip at 1520°C in a pig casting machine with stepless speed control at up to 55 tonnes per hour. The ingots are stacked into self palletizing bundles weighing about 1500 kilograms and are strapped and tagged and transported to the seaport, from which the final shipment is made to the world market. The paper describes constructional details and gives information of both normal operation and start-up and shut-down procedures. Consumption figures for refractory, electrodes, electric energy and refining additions are given and metal chemistry is given before and after refining.

Jan 1, 1979