Search Documents

By C. D. Hall, F. E. Dollarhide

Conventional static tests of fluid-loss agents do not realistically simulate conditions in a fracturing treatment. The dynamic tests reported here show that fluid-loss volume is better represented as proportional to time, rather than as the square root of time. This leads to a different equation for fracture area. The leak-off rate increases with increasing shear rate at the fracture wall, but appears to approach a limiting value. Pressure effects are minor. Spurt loss ordinarily is not affected by the flow velocity in the fracture and is inversely proportional to concentration of agent. The filter cake, once it is well established, is resistant to damage by the flow of plain fracturing liquid (without fluid-loss agent). The latter two findings indicate that a treatment employing a high-concentration spearhead followed by plain fluid can offer a more economical treatment under suitable conditions. INTRODUCTION The successful design of hydraulic fracturing treatments depends on accurate knowledge of the fluid-loss properties of the fracturing fluid. Howard and Fast,' in giving the basic equation relating fracture area to fluid and treating parameters, described three mechanisms which might control the rate of fluid leak-off from the fracture. One mechanism usually is dominant in a given well treatment. For each mechanism, the leak-off velocity is inversely proportional to the square root of time, and the proportionality constant is designated as the fracturing-fluid coefficient. For the wall-building type of fluid-loss agent, the coefficient is determined by a filtration test in a pressure cell, usually with a rock wafer or core as the filter medium. In these static tests, the cumulative volume generally is proportional to the square root of time, after an initial spurt volume. The static-fluid-loss test is not representative of the con,-&tions under which a fluid-loss agent performs in a fratturing treatment. The marked difference between the dynamic- and static-fluid-loss behavior of drilling fluids reported in the literature2,3 implies that dynamic testing is also needed with fracturing fluids. We have therefore undertaken a study of the dynamic-fluid-loss behavior of fracturing fluids. The testing apparatus has also afforded opportunity to evaluate the resistance of the filter cake to removal or damage by flowing fluid containing no fluid-loss agent, with and without sand. The results of these studies offer a means for more accurate evaluation of fluid-loss agent performance, and point the way to a "spearhead" fracturing technique which may offer more economical treatment for some wells. EXPERIMENTAL METHODS The dynamic-fluid-loss testing method is applicable to any type of wall-building fracturing fluid. The present study aimed first at finding what phenomena are involved, and therefore has been limited in the number of materials tested. All of the results specifically reported herein are for kerosene containing a commercial solid fluid-loss agent, which is commonly used at 50 lb/1,000 gal of oil. Another agent in liquid form, used usually at 20 ga1/1,000 gal oil, has shown all the same phenomena in dynamic tests, and generally the same level of fluid-loss control as the solid agent. The dynamic-fluid-loss core cell used in all tests is shown in Fig. 1. The fracture was simulated by the an-nulus between a 2.03 in. OD sandstone core and the surrounding pipe. Annulus widths of 0.234 and 0.117 in. were used, and the core was 3.5 in. long. The annular geometry provides a uniform fluid velocity and a well-defined shear rate over the entire filtering surface, and permits a large filter area (144 sq cm) in a reasonably compact cell. The leak-off fluid passed into a 0.5 in. diameter axial hole in the core. A hollow steel rod through this hole was threaded into a rounded "streamliner" upstream of the core, and into a mounting stud downstream. The streamliner and the stud had the same outside diameter as the core. In all tests except those where sand was circulated, the mounting stud had protruding rings which constricted the annulus, to minimize any tendency for channeling of the fluid to the side exit port. The ends of the core were sealed by Neoprene, steel and Teflon washers. The leak-off fluid was conducted from the hollow rod to an exit tube, through a metering valve (a fine-pitched needle valve) and a quick-opening toggle valve in series, and into graduated cylinders for volume measurement; Two separate circulating systems were used in the experimental program. The extensive initial testing was done at 50 to 150 Psi. The fluid was circulated by a variable speed Moyno pump, and the flow rate was read by a rota-meter flow meter. The filtration Pressure was supplied by holding a back-pressure with a throttling valve. The discharge streamcould be diverted into any of four sections

Jan 1, 1965

By P. Mills

More than 95 percent of all the barite mined and produced is used in the petroleum industry as “drillers mud.” The remaining barite is used in the industrial and medical markets. Therefore, the amount of drilling activity is a good indicator of the health and growth of the barite industry. The four major barite-producing countries in the world are China, the United States, India and Morocco. In 2005, the average number of drilling rigs exploring for oil and gas increased by about 15 percent over the average number in 2004. This increase in oil and gas exploration has resulted in a higher demand for barite and an increase in barite production.

Jan 1, 2006

By R. L. Dietrich

Magnesium alloy sheet has less ability to accept bending at room temperature than most of the heavier metals. In work designed to improve the bend properties, the preferred orientation of the sheet is of major importance as it is in all studies of the properties of wrought magnesium products. When rolled into sheet, all of the common magnesium alloys form an orientation texture having the basal (002) planes approaching parallel to the surface of the sheet. This texture is only slightly affected by annealing. Magnesium single crystals are highly anisotropic, and, as might be expected, so are magnesium alloy wrought products in which a strong preferred orientation is developed. It is therefore not surprising that bend properties are affected by orientation. Ansel and Betterton1 reported that the orientation of AZ3lXt sheet varies from surface to center and that bend properties are improved by etching away the sharply oriented material at the surface of the sheet to reach the more broadly oriented structure below. This paper covers a study of that orientation, either during the rolling process or by treatment of the finished sheet, in an effort to improve the bend properties and toughness of sheet. Literature The orientation texture of magnesium and magnesium alloy sheet has been studied extensively. Early determinations2 showed that pure magnesium sheet has a preferred orientation in which the basal planes are parallel to the sheet surface within very narrow limits. J. C. hIcDonald3 and J. D. Hanawalt4 reported that sheet containing a small amount of calcium develops a "double" texture, that is, the majority of the basal planes are a few degrees from parallel to the surface and there is a noticeable vacancy at the parallel position. Bakarian5 made careful quantitative pole figures of both pure magnesium sheet and MI alloy SEPTEMBER 1949 sheet which show these features. In all of these studies, however, the orientation was determined by transmission methods in which the resulting pattern is an average through the thickness of the sheet. The tendency of wrought metal to exhibit a different orientation at the surface from that in the center has been reported by many investigators. G. von Vargha and G. Wasserman6 found that with copper, aluminum, iron, and brass the textures of rolled compared to drawn wires were the same at the center but differed markedly at the surface. It was also reported by investigators7 that the orientation of rolled aluminum varies from surface to center. Har-greaves8 found that the surface texture of AM503 (magnesium alloy similar to MI) sheet was different from the center texture. It is reported by Edmunds and Fuller9 that zinc alloy sheet sometimes had a thin layer at the surface with a strong orientation of the basal planes parallel to the surface, which, if present, impaired the bend properties of the sheet. Part1 Surface Orientation ofMag- nesium Alloy Sheet and the Effect on Properties Attempts to correlate the bend properties of magnesium alloy sheet with tension ductility over short gauge lengths proved unsuccessful and the subsequent investigation showed that nonuniformity in orientation is a con- tributing factor as the properties of the surface material have a much more important effect in bending than in tension. A program to study the relationship between surface orientation at the surface and bend properties was then undertaken. First, the effect of etching away the surface of sheet on the bend properties and the orientations at the various depths were studied. Sheet samples of M1, AZ31X, and AZ61X were etched in dilute nitric acid to remove the surface material for various depths to 0.015 in. As may be seen in Table 1, the minimum bend radius improved considerably as the surface layers were etched away but it was necessary to etch the sheet quite deeply, much more so than was found necessary by Edmunds and Fuller9 on zinc sheet. It is also apparent that the amount of etching required is a function of the sheet thickness. In all of this work, radii were measured as R/t, the radius divided by the sheet thickness, in order to eliminate the effect of the reduction in sheet thickness produced by the etching. To determine the orientation texture of the sheet, X ray reflection patterns were taken using copper radiation with the bearn striking the specimen at an angle of 17' to the surface, which is the Bragg angle for the (002) planes of magnesium. Two exposures were made of each specimen, one with the beam perpendicular to the rolling direction and the other with the beam parallel to the rolling direction. The symmetry of the preferred orientation in magnesium sheet is such that these two photographs gave an approximation of the pole figure sufficiently accurate for qualitative work and it was not thought worthwhile to make complete pole figures. These X ray patterns show that the orientation has a much narrower spread at the original surface of the sheet than below the surface. The narrow spread is found in sheet having the majority of the basal planes (002) parallel to the surface, and since this is an unfavorable position for slip, it is

Jan 1, 1950

By N. L. Hancox

Previous researchers have used the cutting and rejoining model to represent a porous body when attempting to place Archie's law on a theoretical basis and calculate rock permeabilities (F = Ø-m, where F = formation factor, = - porosity and m = a constant). In using the model, a porous solid is assumed to consist of sections with parallel sides containing straight. continuous pores of total porosity 4 (pore to total volume or, for a homogeneous body, pore to total area). The joining of pores at an interface between two sections is assumed to be random which results in a common pore area Ø2. This reduced area Ø2 is then taken as that area which limits electrical conduction or fluid flow in the body. Agreement between experimental results and results calculated using a model is not always good Because of this, various modifications of the model are presented — for instance, the random nature of the joining is questioned. Formation factor measurements on specially constructed porous specimens are described in this paper. it is concluded that the common pore area limits flow completely only if sections containing straight pores are very thin, and that, in most natural materials, the common pore area at an interface must be greater than that given by random joining. However, the model is still useful in permeability calculations, provided that the fractional area limiting flow is determined from formation factor measurements. INTRODUCTION Two important properties of porous media are permeability k, which describes the ease with which a fluid can flow through a porous medium, and formation factor F, defined as the ratio of the resistivity of a saturated specimen to the resistivity of the saturating liquid which describes the electrical properties of the saturated material. k is defined by Darcy's law,l k= µqL/P Ae . . . . . . . . . . . . . . . [1] where µ = liquid viscosity, q = flow rate, L = length of specimen, p = pressure across the specimen and = - the effective area over which flow occurs, F is given experimentally by Archie's law,2 F = Ø-m ,..............(2) where 4 is porosity defined as the pore to total volume or, for a homogeneous body, the pore to total area; and m lies between 1.3 for loose sand and 2 for cemented sand. Consider a porous body of total cross-sectional area A and length L, saturated with a liquid of resistivity R and with an effective area for conduction of Ae. Then, from the definition of F given previously, F=A/Ae , ................(3) or, from Eqs. 2 and 3, Ae = A Øm ..............(4) Thus, in any attempt to calculate k or F, some assumptions must be made concerning the pore structure of the body and a value derived for A,. To determine Ae, Childs and George3 and Wyllie and Gardner4 suggested an elementary statistical representation often referred to as the cutting and rejoining model of a porous body. The body is assumed to be composed of two or more parallel-sided sections of porosity 4, containing straight, continuous pores with a common pore area of Ø2 at an interface between two sections. The value is given by a random joining of the pores in either section. Two such sections,

Jan 1, 1969

By Kaushik Dey

Bord and pillar is the most predominant method of wining of coal in Indian underground coal mines. Development heading in coal mines often encounters roof stability problem and results in roof overbreak. Research on this reveals that the blast-induced ground vibration may have significant contribution in roof overbreak, especially, when solid blasting is carried out in the bord and pillar method. Solid blasting, in general, is associated with higher charge confinement due to lack of free face and generates higher ground vibration, which in turn results in excess overbreak.

Jan 1, 2008

By Charles E. Wait

IN order to secure cupels uniform in size, density, etc., I have arranged a machine which has proved quite satisfactory, and is so simple and inexpensive as to be within the reach of nearly everyone. It has been in operation here about four years, and with it all cupels used in the assay department of the School of Mines have been made. As shown in the accompanying figure, it consists of a common letter-press, the movable platen of which has been removed. In place of the plate, there is attached to the screw a plunger, which turns with the screw, moving up and down, and making the depression in the cupel. The ring holding the bone-ash is held in place directly underneath the plunger by a wooden guide fastened to the base of the press. There is also fastened to the top of the guide for the ring, at a distance above the base of the press equal to the height of the cupel-ring, a piece of mood about § inch thick, under which the ring will just slide into place, and through which there is cut a circular hole exactly fitting the plunger, guiding it in its downward movement always in the same vertical line; this last guide not only directs the plunger, but also prevents the lifting of the ring by the plunger, upon the raising of the latter.

Jan 1, 1886

By William Reynolds

THIS paper deals with the results of a study of the application and development of mining machines for cutting out and removing dirt bands in bituminous coal beds. FACE PREPARATION When one or more dirt bands1 occur in a seam of coal, the problem of elimination of impurities becomes manifest. The degree of complete-ness to which these impurities are removed at the face has an important bearing upon labor costs, haulage costs and outside cleaning costs, and often the ash content of the product is markedly affected. Yet, because the present-day miner is paid for the number of tons he loads he often lacks interest in the quality of the coal. To insure a clean product, a system of penalties for dirty coal is enforced, but control of extraneous impurity content in the loaded coal is often inadequate and ineffectual when coal and banded impurity are shot as one. It seems only logical that to reduce the amount of impurities by proper face preparation before the men are permitted to load the coal is the most efficient method of preparation.

Jan 1, 1936

By Gaifeng Xue, Lijun Lu, Honghui Fang, Jiannyang Hwang

"Steel slag has been stockpiled in many steel mills due to its poor performance in various construction related applications. Free lime in steel slag has been considered as a major barrier for its utilizations. Composite of steel slag and powders of granulated blast furnace slag have been found an excellent cementitious material for concrete. Portland cement is not required in this kind of concrete. Concretes with various amounts of steel slag and powders of granulated blast furnace slag additions have been investigated. Physical and chemical properties of the products were examined. High performance concrete can be obtained. Field testing of the concrete products was conducted for various applications, including buildings and pavements, and the results demonstrated the soundness of the concrete. Drill cores of field tested concrete, with ages up to 26 years, were examined for the microstructures under SEM.IntroductionIn the steel industry, a major source of the solid waste is steel slag. Steel slag has poor stability in construction applications. This is a major reason that only a small amount of steel slag has been utilized. Some of the reported applications include the land filling/creation in the sea, road base materials, soil treatment for acid neutralization and micronutrients supply, and sintering aid in the sintering plant of the steel industry [1].To solve the stability problem for using steel slag as construction materials, the common approach is to find a method capable of depressing or eliminating the expansion of steel slag. Free lime in steel slag is the major component that causes the expansion. Aging and hydration pretreatment of free lime in steel slag are the well known methods for increasing the steel slag stability. However, there has been limited success on these approaches due to that a large portion of free lime is locked in the grains during the pretreatment process."

Jan 1, 2012

By P Rourke

In this climate of increasing demand for commodities, it is becoming necessary to expand and optimise existing bulk material handling facilities in order to increase capacity to satisfy demand. Production capacity in these facilities is often adversely impacted during the expansion process. A successful and proven strategy to reduce this impact is to bring the additional capacity online in stages coinciding with routine maintenance or other short shutdowns. Compatibility of the automation systems with staged upgrades in capacity is the key to achieving a successful outcome. Since 1994, Hatch has been researching a generic, highly configurable product transport control system that can be reconfigured to cater for plant expansions or modifications without incurring significant risk to production capacity. In 2002, BHP Billiton Iron Ore (BHPB IO) recognised the need for such a generic Route Selection and Sequencing (RSS) system and engaged Hatch to build a generic RSS system as part of the $US351 million BHPB IO Products and Capacity Expansion (PACE) project. In 2004, Hatch successfully deployed such a generic configurable control system at BHPB IO Port Hedland Ore Handling Facility. This generic system is known as the Hatch Product Transport (HPT) System.

Jan 1, 2005

By Mckenzie CK, Leach KR, Bateman KW

Modelling of industrial coal flotation based on data collected in several Central Queensland flotation plants and supplemented by laboratory data is discussed. The model is kinetic in form and provides the basis of an automatic control system. The important features of the model are, 1. a distribution of flotation rates for each species of particles corresponding to the range of particle sizes, 2. a physical restriction on the removal rate of solids in cells where froth 'overloading' occurs. In this condition the removal rate of solids is proportional to the removal rate of water, 3. enhanced particle floatability due to increasing collector addition where froth overloading does not occur, 4. a second mechanism of recovery of all particles by mechanical associ- ation with water. This mechanism is particularly important in the recovery of fine high-ash species.

Jan 1, 1978

By Charles H. MacDowell

Up to 1909 the American public had little knowledge of, or interest in, potash. Some remembered that it had to do with soft soap and sore throat,, but further they knew not. In 1909-10, the German-American potash war, and the publicity attending hostilities, brought home to America the knowledge that potash was an important article of commerce; that Germany monopolized its production and distribution, and exercised all the prerogatives attending complete control. The present war, with its transportation embargo, has again directed attention to Germany's strength as a potash producer and her present unfortunate situation as a distributor. As a consequence, the search for potash takes on new life and it again becomes a subject of general interest. My first knowledge of potash came from a study of the German potash exhibit at the World's Fair in 1893. This investigation led to the recommendation that Armour & Co. engage in the manufacture of commercial fertilizers and the fertilizer branch was organized early in 1894. From then to now " potash " has been a live subject. Two and eight-tenths per cent. of the earth's crust consists of potassium oxide. It is an important constituent of feldspar, granite, and other igneous rocks. Potash is valuable commercially in a water-soluble form. In igneous rocks it is locked in so tight that it is of little value and no utilization in a commercial way has been made of these insoluble forms. Potash in water-soluble form is found in large deposits in Germany; in smaller deposits in Austria and Spain; and in brines in some of our Western arid basins. The deposits in Germany, Austria, and Spain are concentrations from sea waters containing potash derived from the decomposition of potash-bearing rocks. It has been found that the amount of potash remaining in decomposed rocks is not the same as that in the original rock. For instance, granite containing originally 5.58 per cent. potash contained only 1.49 per cent, in the decomposed rock. Syenite containing 6 per cent. in the original

Jan 1, 1915

By T. H. Alden

BaCKOFEN, Avery, and Turner have shown"2 that the large tensile elongation in superplastic metals is correlated with a high strain-rate sensitivity of the flow stress. At present, the reported superplastic materials are complex eutectic or eutectoid systems with a large solubility range in at least one of the terminal phases. This note describes the behavior of a solid-solution alloy (at 22°C)5,= Sn-1 wt pct Bi, which has been processed in order to produce a fine grain size.2,3,6 The chill-cast, 1/2-in.-diam ingot was homogenized for 1 week at 130°C, extruded at O°C to 0.083 in. diam, quenched within 15 sec, and stored at -196°C. Samples were warmed to room temperature 16 hr prior to mechanical testing or metallography. During tension testing at room temperature, it was found that the flow stress reached a steady-state value which depended on the imposed elongation rate and was independent of strain to an error of about ±5 pct. In Fig. 1 is plotted log a vs log e where a is the measured steady-state flow stress and i the imposed strain rate. These quantities were calculated using "instantaneous" area and length to an accuracy in the sample diameter of ±5 x 10-4 in. The log a-log 1 curve is sigmoidal. The strain-rate sensitivity, which may be given by d log old log 6,' has a maximum value of about 0.48 between i = 5 x 10-4 and 5 x 10-3 per min. The value is well above frequently measured values for metals at creep temperatures (0.1 to 0.3) and comparable to the rate sensitivity for Pb-Sn solder: which has been shown to be superplastic.2,3 Note, however, that below or above the strain rate of 10-3 per min the rate sensitivity of Sn-1 pct Bi decreases and at high rates is more nearly like that of conventional metals. The grain size of this material is relatively uniform, Fig. 2, and may be specified by an average linear intercept i.' Grain growth occurs at room temperature but after 16 hr, L = 5. Tensile elongation was measured on finer-grain-size specimens, which had been at room temperature 15 min prior to testing. After 15 min, the samples are fully recrystallized. Three strain rates, 5 x 10-3, 10-2, and 2.5 x 10-2 per min, were employed for which the measured elongations varied from 425 to 500 pct. These results would seem to justify the term superplastic, applied to this alloy, although the ductility is inferior to that of the Sn-Bi eutectic.3 The Sn-1 pct Bi alloy, which is a single-phase material with equiaxed, fine grains, is an excellent one on which to make an estimate of the Nabarro-Herring9 creep rate. According to the model of Avery and Backofen2 a substantial part of the deformation must be accomplished by N-H creep in the strain rate-temperature regime in which d log a/d log 1 = 0.5. The maximum N-H creep rate is given by9 L2kT where v is the atomic volume and D the self-diffusion coefficient. For this test v = 3.O x 10-23 cu cm, D = 1.4 e-23,300/RT = 2.5 x 10-l7 sq cm per sec,7 L = 5x 10+4 cm, T = 295°K, and a = 2000 lb per sq in. = 1.38 x 10' dyne per sq cm. The calculated creep rate is E= 4 x 10-11 per sec which may be compared with the measured creep rate at this stress, Fig. 1, of 6.7 x 10-5 per sec. The N-H creep rate is seen to be negligible. Earlier consideration2 of this question was in error because incorrect diffusion coefficients were used. The assistance of R. R. Russell in metallography is acknowledged gratefully.

Jan 1, 1967

By J. M. Cormie

"The orebodies of the East Malarcic mine are interesting from a geological standpoint because of the very small amount of vein quartz, the occurrence of much of the ore in soft greenstone schist, the presence of innumerable bodies of porphyry and diorite, and their obvious relationship to structural features .The property lies in the northeast part of Fourniere township in western Quebec, and within the important fault zone that geological mapping in recent years has shown is traceable wesrward through the Noranda and Kirkland Lake camps and eastward to beyond the Val d'Or region . The claims included in the property were staked by J.P. Norrie and L. K. Coffin in 1932, but gold was not discovered until i934. Production began late in 1938. The total amount of ore milled up to the end of 1945 was 2,837,091 tons from which gold having the value of $16,631,758 was recovered.The region is underlain by an alternating series of Early Precambrian sediments and volcanics cut by innumerable intrusives. These are more fully described in the works of Gunning, Ambrose, and Norman. The East Malanie property is underlain by three formations, which, named from north· to south, are : the Cadillac sediments, the Blake River volcanics, and the Kewagama sediments. In addition, there are countless intrusions of porphyry and diorite, particularly in the greenstone, occurring in all sizes up to those measurable in hundreds and even thousands of feet . These constitute a large proportion of the greenstone in places. In many parts of the ore zone there is more porphyry and diorite than schist. The greenstone itself is not homogeneous but includes peridotite, andesitic lava, and soft talcose schist.Orebodies have been found in both the Blake River volcanics and the Kewagama sediments. They are not known to occur in the Cadillac group. The ore occurs in a zone of pyrite mineralization in which almost no other metallic minerals and very little vein quartz are present. Generally, the grade varies directly with the amount of pyrite. The mineralization is later than all the rocks of the area. Diorite was a particularly favourable rock for mineralization and contains the highest grade of ore, but any rock in the fault zone may be ore-bearing, whereas the same type away from the zone is not."

Jan 1, 1954

By Shichao Zhao, Ke Xie, Qijie Zhai, Wenbin Xia, Yuanyi Guo, Changjiang Song

"This paper investigated the structure evolution and phase formation ofFe-(11,13,15wt.%)Mn alloy under near-rapid solidification conditions. It is found that the area ratio of equiaxed zone in the Fe-13Mn alloy is the largest. And the primary dendrite arm spacing of Fe-(11,13,15wt.%)Mn alloy increased clearly with increasing distance from the surface. The volume percentage of HCP phase increased with increasing manganese content in the range from 11 pct to 15pct.IntroductionThe developing trend of automobile is the energy conservation, enviromnent protection, light weight, and high security. So the material would be required to the higher strength, higher plasticity and more likely to processing of automotive steel. Fe-Mn based alloys is considered as a potential material to the third generation automobile steel for its high damping performance [1], good mechanical properties [2-3], and high young's modulus [4]. And it is important that metastable HCP phases of Fe-Mn based alloys, which attracts technological interest for theoretical and experimental research [5-6].Metastable materials have been extensively used in the area of iron steels. Among various fabrication methods for high performance materials, rapid solidification is one of most popular ways to produce advanced materials by obtaining metastable phases. The solidification of metals in metastable phases provides access to an extended range of materials properties with novel properties [7]. Thus, in this work, Fe-Mn alloy metastable materials prepared by near rapid solidification is studied."

Jan 1, 2013

By N. L. Wesis

General History The first jaw crusher in the US was patented about 1830, but the Blake crusher that has maintained a substantial advantage over other types was invented in 1858 by Eli Whitney Blake. For going on 150 years the jaw crusher has been an invaluable machine; even today, when gyratory crushers have assumed most of the burden of crushing large tonnages of large rock and ore, the jaw crusher has a firm place in the mining industry. It is interesting that soon after the invention of the Philetius Gates gyratory crusher in 1881, a contest between the first No. 2 Gates and Blake jaw crushers of equal gape showed the gyratory to be 3.2 times as fast. This foretold a day not far in the future when the jaw crusher would not be adequate on the largest jobs. In his Textbook of Ore Dressing (1909) R. H. Richards recom¬mended that the word breaker be used for all machines breaking to relatively large sizes (say to 5 in. or greater), and crusher be used for finer work. Even in the 1968 US Bureau of Mines dictionary of mining terms the work breaker is defined by Richards in this context. However, in modern US usage it is nearly limited to coal breaking. Over the years the jaw crusher has been developed in a variety of forms but it appears today in these three general forms: (I) Blake type, (2) Dodge type, and (3) single toggle (or overhead eccentric) type. All of these crushers have a fixed jaw and a moving jaw, between which the coarse rock fragments are intermittently caught and crushed. The three types are differentiated by the manner in which the movable jaw is moved in relation to the fixed. Types The Blake-type crusher is shown in cross section in Fig. 1. The simplicity and strength that have made it first among jaw crushers are evident. The movable jaw is suspended from a cross-shaft at its upper end, this shaft being carried in bearings on the sides of the frame. The actuating mechanism consists of an eccentric shaft, also supported in frame-mounted bearings, which imparts through a pit¬ man and a pair of toggles a reciprocating motion to the bottom of the swing jaw, the return movement being effected by several spring¬loaded rods. The whole is built into a box frame with the crushing chamber at one end. As in all jaw crushers, the eccentric shaft is equipped with a heavy flywheel that maintains an even speed through¬out each stroke. The Dodge-type crusher illustrated in Fig. 2 is simple, mechani¬cally. Its movable jaw, being pivoted below the discharge opening, has minimum movement at crusher discharge and maximum at crusher feed. Because the choke point coincides with the point of least motion, these crushers are of relatively low capacity, and the rapid action in the feed area gives the machine the advantages of large reduction ratio and closely sized product. Thus, it fits well into low-capacity operations like sample reduction. Besides low capacity, its principal disadvantages are tendency to pack and make fines. The single-toggle or overhead-eccentric type of jaw crusher (see Fig. 3) has gained in usage, starting as a modification of the Dodge idea in that the greatest movement of the movable jaw occurs at the top, and being gradually improved and strengthened to its position today where it covers just as wide a field of application as the Blake type from the standpoint of feed opening. The motion of the movable jaw is the result of the circular motion of the eccentric shaft at the top of the swing jaw combined with the rocking action imparted to the bottom by the inclined toggle plate. Because of light weight and mechanical simplicity, it is economical in small mills and portable plants where the rock is not as tough and abrasive as to punish the machine with excessive impact from shocks, or excessive wear result¬ing from the pronounced vertical component of motion.

Jan 1, 1985

By Gerald, Sherman

INCREASED production and con¬sumption of all metals, indicate the progress of industry toward that condition formerly thought to be normal. With no market limitations on silver and gold the two new precious-metal mines, the Silver Queen (now the Golden Queen), in southern California, and the Sunshine, at Kellogg in northern Idaho have made progress toward a high routine production. The Golden Queen 300-ton mill is finished and ready. The Sunshine mill has been enlarged and production is now at the rate of 500 tons per day of high-grade silver ore. The Hecla Mining Co. is developing the Polaris vein, which should be the extension of the Sunshine to the east. Some rich ore is reported. The developments of the' East African Gold Fields, Ltd., in the Lupa gold field of Tanganyika Territory, have made good progress, but operation in an isolated locality is not rapid and a large plant will be required. There have been no other discoveries reported that can be compared with the three mentioned, but production has increased, with greater capacity in dredging equipment and underground mines more adequately prepared for production.

Jan 1, 1936

By Walter K. Utt

The process of drilling and bolting the roof is currently one of the most dangerous jobs in underground mining, resulting in about 1,000 accidents with injuries each year in the United States. To increase the safety of underground miners, researchers froth the Spokane Research Laboratory of- the National Institute for Occupational Safety and Health are applying neural network technology to rite classification of mine roof strata in terms of relative strength. In this project, the feasibility of using a monitoring system on a roof drill to assess the integrity of a mine roof and warn a roof drill operator when a weak layer is encountered is being studied. Using measurements taken while a layer is being drilled, one can convert the data to suitably scaled features and classify the strength of the layer with a neural network. The feasibility of using a drill monitoring system to estimate the strength of successive layers of rock was demonstrated in the laboratory.

By H. N. Mills

The glass industry is a major user of many industrial minerals in the manufacture of its product. It is the intent of this chapter to: (1) acquaint the reader with the glass industry by including a few production statistics, and then (2) cover the various aspects of the major raw materials used to make glass. Some of the items covered are: type of materials, their function in glass, their composition, cost, and the relative quantity used in glass vs. totals produced. In addition, a discussion of glass raw material specifications, some byproduct materials used in glassmaking, and comments on future prospects related to the environment, technology, and growth are included. The matter of glass compositions, properties, and batches is considered beyond the scope of this chapter which deals only with raw materials. For more details on the particular minerals and rocks, the reader is referred to the commodity chapters in this book.

Jan 1, 1975

By W. A. Griffith

Fractional replication of factorial design, a general method for planning experimentation and for analysis of data obtained, is described as applied to a flotation investigation. This method leads to determination of optimum process conditions with minimum experimental effort. Its advantages over simple factorial design are demonstrated. A METHOD for planning experimentation and for analyzing the data secured will be demonstrated. This method, termed fractional replication of factorial design, employs a relatively small number of individual experiments to determine which of a large number of process variables are controlling, to determine which combination of levels of these variables is most likely to produce optimum results, and also to predict what results will be obtained with a particular combination of conditions not already tested. Although the general method is not new, having been developed by Finney in 1945,' the extent to which it can improve the effectiveness of applied research generally has not been recognized by metallurgists. The fractional replication procedure is particularly useful in flotation experimentation and an example from such an investigation will be used in the paper. However, it has equal value in any investigation in which similar experimental difficulties are encountered. In developing a flotation process for a particular mineral separation, the investigator is inevitably confronted with the following difficulties: 1—There are a large number of potentially important process variables. 2—Results of individual experiments are not highly reproducible, due in part to the difficulty in precisely controlling all the variables. 3—Considerable effort is expended in conducting individual experiments. 4—There are practical limits on the number of individual experiments which can be made. In situations of just such a type, modern statistical methods of planning experimentation and analyzing data have their greatest value. Applications of one such technique, called factorial design, to problems of this type have been described by Dorenfeld and others.'-' The simple factorial design is an efficient procedure when the investigator hopes to provide a comprehensive understanding of the effects and interrelationships of a small number of variables over a limited range. In applied research, this is seldom the main objective. Rather, the investigator usually wishes to determine which of the many potentially important variables are in fact controlling, which levels of the controlling variables will provide opti- mum metallurgical results, and what these results will be at optimum conditions. Interest in detailed trends is limited to the controlling variables and to levels in the region of optimum conditions. Simple factorial design has serious deficiencies for such objectives and is not the most efficient method of experimental design. Deficiencies of Factorial Design In a simple factorial design, an experiment must be made at every possible combination of each level of every variable, once these have been chosen and the levels of each to be included have been decided upon. As the number of variables or levels of each increases, the experimental program quickly reaches prohibitive size. For example, an investigation of only four variables, each at four levels, requires 256 individual experiments. Often upon completion of such an extensive program, it is found that one or more of the variables has metallurgically unimportant effects or that a poor estimate has been made as to the appropriate range of levels to be investigated. The result is that only a small proportion of the data obtained falls in the range of real metallurgical interest. Indeed, it frequently can be anticipated that certain combinations of levels of variables will not produce results of interest, but they still must be included so that the essential balance, or orthogonality, of the design will be retained. It may be true that factorial design will provide the greatest amount of information from a given number of experiments, but it does not necessarily follow that it will lead to the desired information with a minimum number of experiments. Much of the information provided may be of little value. Advantages of Fractional Replication The disadvantages of simple factorial design are overcome to a great extent by a modification known as fractional replication. This is a technique for sampling systematically the potential data of a full factorial experiment, that is, the data which would have been obtained if the complete factorially designed program had been completed. Only a fraction of the total array of experiments is made, but the experiments are chosen in such a way that the important advantages of factorial design and the accompanying analysis of variance are retained. The data obtained from the first group of experiments are used to determine which of several variables are controlling and which levels of these variables are most likely to produce the desired result. Unimportant variables and levels of variables then may be

Jan 1, 1956

By Hugh Douglas

ANTIMONY Antimony (Sb) has been used since the early Egyptian dynasties. Prior to World War I, total demand amounted to only 6000 to 7000 tons per year (tpy). Wartime uses and rapid rise of industrialization in the Northern Hemisphere nations have pushed world antimony use to the 78,000-tpy level. An overwhelming supply of low-cost antimonial resources in the Sino-Russian bloc countries has and will continue to have a major impact on availability and price to users outside the bloc. Table 14.4.1 shows trends in world production, United States production and consumption, and prices. Demand Antimony is used principally as an alloy in lead-based metals and other alloys. Pure metallic antimony usage is small and is confined to such areas as laboratory and electronic applications. Lead-antimony alloys are used in automobile storage batteries, chemical pumps, and pipes, tank linings, roofing material, and cable sheaths. The metal increases the hardness of lead, and, for such uses as foundry printing type, reduces shrinkage for casting and lowers the melting point. Antimonial oxides are used for ceramic purposes, white paint pigments, glass forming, textile finishing, fire retardants in military clothing, matches, and solder. Wartime applications include use as hardener for bullets, an element for tracer bullets, and ingredient for producing dense white smoke for visual markers. A small but rapidly growing use for antimony is for metallic compounds in semiconductors and thermoelectric devices. In the United States demand for antimony is about evenly divided between metallic end-use markets and nonmetallic markets. In metallic end uses, antimonial lead accounts for 27% of total metallic and nonmetallic use; in nonmetallic areas major uses are flame retardants (15%) which is the fastest growing market, plastics (13 % ), and ceramics and glass (11%). While antimony has advantages in most of its applications, there are uses in which other materials can be substituted, including: mercury, titanium, lead, zinc, chromium, tin, and zirconium in paints and pigments; tin in sheathings; calcium in battery plates; and bismuth in type metal. Supply Antimony is produced from both antimony ores and as a byproduct of smelting other ores. The principal ore mineral is stibnite (Sb2S3), along with its oxidized antimonial minerals and derivatives which occur in small discontinuous replacement veins or fissure vein implacements. Stibnite occurs in quartz-gold veins and copper-lead-zinc

Jan 1, 1976