Search Documents

By P. B. Elkin, K. C. Ten Brink, Allen D. Garrison

It is the purpose of this article to present the results of an investigation of certain clay and shale suspensions having viscosities that are materially influenced by fluid motion, and to discuss the bearing of these results upon the choice of policy in the control of drilling fluids. A previous article described the design and the characteristics of an instrument adapted to measure the viscosity of plastic suspensions during continuous uniform motion and at a variety of speeds.' It has long been recognized that the viscosity of a clay suspension depends on the past history of the fluid motion. Since an abundance of literature is available on this phenomenon,2 it is not necessary to describe it in more than general terms. It is usually observed that rapid motion reduces the viscosity of a clay suspension, and that some time is required for the viscosity to fall to its equilibrium value after the steady motion is started. On reducing the speed of motion to some lower value, the viscosity again rises, but it also requires some time to attain a steady viscosity value at the slower rate of motion. Thus clay suspensions are usually observed to be increasing in viscosity as time passes when the measurement has been immediately preceded by fluid motion that was more rapid than that employed in the measurement. And it is usually observed that the viscosity falls as time passes when the measurement has been preceded by more quiescent conditions. Reed,3 and Broughton and Hand4 have reported a condition of observation of clay suspensions in which the viscosity was observed to fall during the first few moments of steady motion, and rise thereafter. The characteristics of the new instrument are particularly well adapted to studies of this kind. With it we have been able to observe all of the phenomena described above, and it is important to understand their nature because they all occur at some time during normal drill-

Jan 1, 1940

By K. C. Ten Brink, Allen D. Garrison, P. B. Elkin

It is the purpose of this article to present the results of an investigation of certain clay and shale suspensions having viscosities that are materially influenced by fluid motion, and to discuss the bearing of these results upon the choice of policy in the control of drilling fluids. A previous article described the design and the characteristics of an instrument adapted to measure the viscosity of plastic suspensions during continuous uniform motion and at a variety of speeds.' It has long been recognized that the viscosity of a clay suspension depends on the past history of the fluid motion. Since an abundance of literature is available on this phenomenon,2 it is not necessary to describe it in more than general terms. It is usually observed that rapid motion reduces the viscosity of a clay suspension, and that some time is required for the viscosity to fall to its equilibrium value after the steady motion is started. On reducing the speed of motion to some lower value, the viscosity again rises, but it also requires some time to attain a steady viscosity value at the slower rate of motion. Thus clay suspensions are usually observed to be increasing in viscosity as time passes when the measurement has been immediately preceded by fluid motion that was more rapid than that employed in the measurement. And it is usually observed that the viscosity falls as time passes when the measurement has been preceded by more quiescent conditions. Reed,3 and Broughton and Hand4 have reported a condition of observation of clay suspensions in which the viscosity was observed to fall during the first few moments of steady motion, and rise thereafter. The characteristics of the new instrument are particularly well adapted to studies of this kind. With it we have been able to observe all of the phenomena described above, and it is important to understand their nature because they all occur at some time during normal drill-

Jan 1, 1940

By Allen Garrison

IT is the purpose of this article to present. the results of an investiga-tion of certain clay and shale suspensions having viscosities that are materially influenced by fluid motion, and to discuss the bearing of these results, upon the choice of policy in the control of drilling fluids. A previous article described the design and the characteristics of an instru-ment adapted to measure the viscosity of plastic suspensions during continuous uniform motion and at a variety of speeds.1 It has long been recognized that the viscosity of a clay suspension depends on the past history of the fluid motion. Since an abundance of literature is available on this phenomenon,2 it is not necessary to describe it in more than general terms. It is usually observed that rapid motion reduces the viscosity of a clay suspension, and that some time is required for the viscosity to fall to its equilibrium value after the steady motion is started. On reducing the speed of motion to some lower value, the viscosity again rises, but it also requires some time to attain a steady viscosity value at the slower rate of motion. Thus clay suspensions are usually observed to be increasing in viscosity as time passes when the measurement has been immediately preceded by fluid motion that was more rapid than that employed in the measurement. And it is usually observed that the viscosity falls as time passes when the measurement has been preceded by more quiescent conditions. Reed,3 and Broughton and Hand4 have reported a condition of observa-tion of clay suspensions in which the viscosity was observed to fall during the first few moments of steady motion, and rise thereafter. The characteristics of the new instrument are particularly well adapted to studies of this kind. With it we have been able to observe all of the phenomena described above, and it is important to understand their nature because they all occur at some time during normal drill-

Jan 1, 1939

By Jin Liu

In the early 1990?s, Inco successfully installed two new flash furnaces as part of their SO2abatement project to reduce SO2 emissions from the Copper Cliff Smelter by 60%. The flash furnace off-gas is cooled and cleaned through two new Monsanto Dynawave gas cleaning systems that replaced the traditional venturi scrubbing system. It was discovered that the flash furnace production capacity is often limited by the capacity of the gas cleaning system. The key task is to eliminate pressure drop from the system. The froth column is responsible for by far the largest pressure drop in the gas cleaning system. Initially, the column was fitted with 22 plates. In 1994, both #1 and #2 froth columns were modified by reducing the number of plates in each column from 22 to 18 and increasing the interplate spacing on lower plates. With increasing demand for more throughput in the flash furnaces, further modifications on the froth columns were made in 2005. This paper describes these modifications and results together with some fundamental analysis of the froth column characteristics.

Jan 1, 2006

By A. S. Yue

Small-angle tilt boundaries have been observed in a lamellar eutectic structure. These boundaries are morphologically similar to a theoretical till boundary originally proposed by Burgers. The production of a small-angle tilt boundary in the lamellar eutectic structure is attributed to the formation of an indentation on a planar solid-liquid interface during growth. Constitutional supercooling due to the accumulation of impurity atoms ahead of the interface is primarily responsible for the generation of an indentation. The distance between two faults of like sign, designated as lamellar fault distance, is calculated by the Burgers equation for small-angle boundaries. It was found that the lamellar fault distance decreases exponentially and the tilt angle increases exponentially with freezing rate. SMALL-ANGLE tilt boundaries have been observed in many crystals in the as-grown states by etching techniques. However, a detailed substantial proof for revealing the presence of dislocations in the form of etch-pits was recently accomplished by Vogel. These boundaries are described as an array of dislocations of like sign. The angle of tilt associated with a boundary is treated theoretically by Burgers3 and is given by 0 = b/D for small tilt-angle where b is the Burgers vector of the dislocations and D is their average spacing. During the course of experimentation on the solidi fication of the lamellar Mg-32 wt pct Al eutectic a microstructure which was strikingly similar to a dislocation tilt boundary was observed. An example of the type of microstructure is given in Fig. 1, which shows a combination of transverse and top sections of the lamellar eutectic structure. The lamellae of the top section on one side of the apparent tilt angle are not parallel with those on the other side. Consequently, some lamellae must be terminated somewhere. Fig. 1 shows that the termination of lamellae is analogous to a dislocation tilt boundary in a crystal lattice originally proposed by Burgers. This work represents a closer look at such structures. The factors governing the production of the small-angle tilt boundary are discussed in terms of the freezing condition and impurity distribution in the melt. The effect of freezing rate on the distance between two faults, designated as lamellar fault distance, and the tilt angle is also described. In addition, the lamellar fault distance is determined by means of the Burgers equation for small-angle tilt boundary. EXPERIMENTAL PROCEDURE The slightly impure Mg-32 wt pct Al eutectic rods, 5/8 in. in diam and 12 in. long, were made from 99.99 wt pct Al and 99.98 wt pct Mg and were cast in a high-purity graphite mold. Some of these rods were purified by zone-refining the eutectic using direct-radiation helical-coil furnaces5 A molten zone about 2 in. long was passed through the cast rods at a speed of 5.3 x 104 cm per sec for ten passes of the molten zone. Before the freezing experiment was begun, 2-1/2 in. of the material from the head and tail ends of the zone-refined eutectic were removed from the rod to eliminate any impurity. The freezing experiments were carried out under controlled conditions,8 using a protective atmosphere of purified argon. At the end of each run, observation of the tilt boundary was made throughout the entire length of the rod with a light microscope on the top, longitudinal, and transverse sections (three mutually perpendicular sections) of the lamellar eutectic solid. The experimental data used for the determination of interlamellar spacing and tilt angle were taken from the middle portion of

Jan 1, 1964

By D. J. Brown

Froth flotation is now used to recover millions of tons of fine coal,(-1/2 mm), every year. For example, in Great Britain, 4-million tons of flotation concentrate was produced in 1960, about 3% of the mechanically cleaned out- put and 2% of the total salable output. Coal flotation is not so widely practiced in the U. S. as it is in Europe since much American coal occurs in thick seams of high grade and does not require cleaning. However, in the U. S., as elsewhere, the increasing mechanization of coal mining machinery has lead to a lowering in size and grade of product from the mine and to an increasing need for cleaning of coal to improve the grade before sale. With an increasing proportion of fines in the product, froth flotation has assumed a greater importance as a cleaning process for coal. In the last three years, over 40 flotation plants have been put into operation in the Appalachian area of the U. S.80 Fine coal recovered by means of froth flotation may be used as a powdered fuel alone or mixed with coarser grades. The removal of this fine coal from washery water makes possible the recirculation and re-use of the water and also leads to improved and more consistent operation of jigs and other separating machines which function less effectively when there is a build-up of fine solids in the washery water. Finally, froth flotation is of assistance in the production of a clarified effluent which may be discharged from the washery without polluting local rivers, streams, or wells. The 1961 cost of installing a new coal flotation plant in Great Britain would be about $19,000 per ton of dry solids input per hour, including the cost of new buildings and coal and shale filtration and water clarification equipment. The figure for the gravity concentration of the large coal, the main plant, would be about $4,800 per tph. The operating cost for the new coal flotation plant would be about $1.10 per ton. Even at this level of cost the cleaning operation is economic in Great Britain for coking coals. In the U. S., a froth flotation cost of 14$per ton of cleanfilter cake was quoted early in 1958 for one operation,l though admittedly this was a special case. Assuming a cake moisture con- tent of 30%, it is estimated that this cost is equivalent to a figure of 256 per ton of dry solids input, for the incorporation of coal flotation in an existing washery. A cost oh 416 per ton of concentrate was quoted76 in a recent analysis of flotation economics, this cost being brought up to $1.11 per ton after payment of royalty, welfare and association dues and taxes. Capital cost was $120,000 for a plant producing 133 tpd of concentrate. Before considering the treatment of coal by flotation it is appropriate to survey some of the properties of coal which are of importance in the process.

Jan 1, 1962

By J. Lu, M. Mohammadi, C. Pelletier, B. Wassink

Chemical reduction of selenate by chromous ions is proposed as a novel method to remove selenate from sulfate-bearing solutions Chromous ions were generated by electrochemical reduction of chromic ions using an electrochemical cell. The investigation was conducted in sulfate medium and under various concentrations of chromous ions (0.0062 to 0.05M), pH 1 to 2.2 and temperature 10 to 60°C. Selenate ions were rapidly reduced by chromous ions to hydrogen selenide. The overall reaction at a chromous/selenate molar ratio of 8 or higher can be expressed by the following reaction. At an initial chromous/selenate molar ratio below 8, the products are hydrogen selenide and elemental selenium. At a lower chromous/selenate molar ratio and pH, more elemental selenium and less hydrogen selenide are produced. The reduction kinetics is controlled by both chromous ion and hydrogen ions concentrations. The reaction rate is first order with respect to selenate, hydrogen ion and chromous ion concentrations. It was found that the selenate reduction rate with chromous is independent of the concentration of sulfate present in the solution. The general rate equation was proposed and the rate constant was calculated as k= 0.38 M-2s-1. An activation energy of 58.7 kJ/mol was obtained in the temperature range from 10 to 50°C. Nearly 100% of selenate can be reduced to H2Se from solution containing 17 ppm selenate in less than 30 minutes at pH 2.2 and 60°C. Various strategies have been tested to remove the produced H2Se from solution. INTRODUCTION Selenium in nature is mostly associated with metal sulfide minerals such as copper, iron, zinc, and lead sulfides (Zingaro & Cooper, 1974). The extraction of metals from ores has the potential for selenium contamination of ground and surface water which can pose an environmental and health concern. Therefore, selenium contamination in the receiving environment is a key issue for many industries (specifically copper industry) and the treatment of wastewater contaminated with selenium is a growing challenge. The effective removal of selenium from contaminated water is very important to support sustainability in the copper industry and the other industries with selenium pollution issues.

Jan 1, 2019

By B. F. Oliver

A levitation zone melter is described which has the necessary characteristics for processing metals of controlled purity. No crucible is required; control of the solidification variables is stable; the environment of the charge is chenzically controlled. Rotation of the solidifying interface and mixing in the liquid by the magnetohydrodynamic stirring produce an eight-fold increase in freezing velocity over former melting units with better resulting solute redistributions. The smooth appearance of processed specimens, resistivity ratios as a hnction of position, as well as a segregation curve, are presented as evidence of smooth continuous solute fransport over distances in excess of ten zone lengths. THE difficulties of the floating zone-purification of higher density metals in large quantities under conditions of lowered surface tension are well known and have hindered fundamental research programs for some time. The inordinate amount of time required to obtain a small reproducible yield of high-quality metal has excluded the use of such material for many important material research programs. However, with the use of controllable induction levitation forces' to accomplish stable liquid zones with nearly flat solidifying interfaces, and with good physical and chemical control of the processes involved, these difficulties can be overcome. A zone melter that is to be used for both high-purity and controlled composition work in metal systems must have the following three characteristics: 1) The process must avoid the use of containers. 2) Physical control of the solid-liquid interface and of the mixing within the liquid phase must be stable. 3) The chemical environment of the melt chamber must be controllable. A description of an apparatus that accomplishes these objectives follows.* APPARATUS One of the basic features that is necessary for good process control of large sections is that the charge, the coil, and the motion mechanisms be within the same chamber. This arrangement permits a close coupling between the work coil and the load, which then provides a good flexibility for adjustments of coil dimensions, for controlling the amount of levitation needed for stable operation at a given power level. An overall view of the melter is shown, with the melt-chamber door open, in Fig. 1. The radiation shields surrounding the single-turn induction coil are of water-cooled copper. The chamber is stainless steel, as are most of the components within the chamber. The control panel for the scanner is located at the immediate lower right of the melt chamber. This panel controls the operation of the scanner. The operations controlled are the interface rotation rate, the stretch-squeeze or diameter control, the up and down scanning speeds, and the induction power. All of the drive motors are constant-torque variable-speed motors. The scanning speeds are set with precision helipots and continuously observed with the voltmeter on the control panel and checked with a mechanical indicator within the melt chamber. The rotation rate is also set with a precision helipot. The up-scanning speeds are 2 to 300 in. per hr.

Jan 1, 1963

A concept gaining attention among rock mechanics researchers in studies of soil-structure inter- action is the use of compressible packing between the structure such as tunnel lining and the soil or rock. Lester H. Gabriel, provided information about work on this concept at the II Symposium on Rapid Excavation, October 16-17, 1969, Sacramento State College, Sacramento, Calif. It is well-known that loads transmit their effects to those locations which deform least. Traditionally, the question to be answered by the structural engineer is how rigid the structure ought to be. The stronger the structure, the more resistant it becomes to deformation. If it is more rigid than the surrounding strata, the structure acts as a pillar, focusing load on itself. However, if the structure is less rigid than the surrounding strata, blocking or packing between the structure and the enclosing material facilitates the formation of soil or rock arch. The object then is to design and build structures such as tunnel linings, which harness the advantages of carefully planned small movements. Tests on plaster cylinders imbedded in granular sand and loaded were compared to those of plaster cylinders protected in sheathing of polyfoam rubber. The compressible sheath permitted support of up to ten times greater loads Gabriel, Lester H., "Principles of Soil-Structure Interaction Applied to Tunnel Linings." Hecla Mining Co. has successfully used shotcrete with substantial cost savings for ground support purpose. To date, the use of shotcrete in Hecla's operations has been limited to openings where long-term high quality support was required, in exceptionally difficult ground, and to a limited degree in stope support. Experience with both the wet and dry process indicated that the latter was better for their applications. The availability of effective accelerators which reduce losses from rebound, give high-early strength and permit placement in wet conditions, led to this conclusion. The gross cost under such conditions as those at Hecla, including rebound losses and overshooting, is estimated by Hecla to be $51 per cu yd.

Jan 12, 1969

By Charles W. Merrill

Obsolescence in the mineral world is virtually nonexistent if the term is taken to mean that a mineral commodity, once established in commerce and industry, subsequently has fallen into disuse. We are living in an age of minerals. Each generation puts an increasing array of mineral-based commodities, in larger quantities, to more uses than ever before. Bastnasite, a museum mineral and a collector's item a few years ago, is now produced in quantity at Mountain Pass, Calif. Uranium, a minor byproduct of vanadium mining in the Rocky Mountain plateau area before World War 11, has grown to be a leading mineral product in several western States. And finally the total quantity and value of minerals both in the United States and in the World establish new records almost yearly. Surely the mineral industry as a whole is not obsolescent in our economy. Nevertheless, there are particular uses for particular minerals that are obsolescent and some applications have been supplanted entirely. Tin does not occupy the prominent place in foil manufacture that it once did, and the schoolboy's slate left most classrooms before the oldest of us were born.

Jan 9, 1964

By D. Goodings, W. L. Fourney, Bonenberger, R., Uli Leiste

The problem of the maximum depth at which a mine buried in the surf zone or beach zone is a threat to landing vehicles is being studied by Naval Surface Warfare Center (NSWC), Indian Head Division, Naval Research Laboratory (NRL), and The University of Maryland Dynamic Effects Laboratory. The problem was divided into two parts: The first part involves determining how deep a pressure plate mine can be and still detect a vehicle passing over it. This requires determining the distribution of stress within dry and saturated sand when a vehicle passes over a buried mine. The results obtained from that study are presented in a related paper (1). This paper will cover the second part, which entails determining the impulse delivered to the vehicle. This is equivalent to determining the impulse delivered to a plate suspended above the detonating explosive charge and includes an investigation of the distribution of the impulse over the plate. The purpose of the research is to develop a scaling law and/or computational capability which will permit predicting impulse to be expected in the field from tests conducted in the lab. The computational effort is aimed at the development of and confidence in computer codes that can be used to predict stresses and strains in plates due to the detonation of buried mines.

Jan 1, 2004

By C. E. Jr. Reistle

ALL crude oils become more viscous when chilled, but the only oils that congeal and precipitate paraffin to such an extent as actually to cause production troubles are those that contain an appreciable amount of wax. In handling these oils of high wax content, three distinct problems may be encountered before the oil reaches the refinery. The first problem is the precipitation and accumulation of paraffin in the well, either in the oil string or on the face and in the pores of the sand. The second problem is the accumulation of paraffin and the congealing of oil in the transportation lines. The third problem is the precipitation of paraffin and the formation of tank bottoms.

Jan 1, 1927

By R Willis, D Cooke, G J. Davidson

Mine-groundwater interaction at the Pasminco Rosebery Mine (PRM), western Tasmania, deserves special attention due to the unique climate and mining environment present. High rainfall and low evapotranspiration result in an excess of water, an uncommon problem at Australian sulfide bearing mines. Research is being undertaken to delineate current subsurface fluid flows and predict future fluid flows in order to improve management after mine closure. Acid mine drainage generation is well developed in abandoned mines throughout the area. If acid mine drainage is not controlled after mine closure, significant environmental degradation could occur in the receiving waters of the Pieman River system. The study area encompasses the heavily forested Mount Black, and underlying PRM workings. Groundwater flows beneath Mount Black through a crystalline fractured rock aquifer with faults and underground mine workings observed to act as the major hydraulic conduits. Recharge is controlled by local precipitation, and the ultimate discharge is thought to be the Pieman River system, which forms the topographic low in the area. Slug tests have been used in conjunction with the mineÆs extensive geotechnical database to spatially evaluate variation in hydraulic conductivity. In fractured rock terrain associated with mining, rock quality designation data can be a useful tool in delineating areas of similar hydraulic conductivity when combined with conventional hydrogeological methods. A GIS, mine planning software, an environmental and a geological database are linked to form the input for groundwater modelling.

Jan 1, 2003

By Marshall GA

Structural fatigue damage of haul truck frames is a costly problem associated with the operation of large mine haul trucks. A monitoring programme is described which has been instigated to measure stresses in the frames of haul trucks under actual mine operating conditions. The instrumentation used and methodology employed in the computer analysis of the results is briefly described. The results of the monitoring programmes are reviewed, and the effects of various factors affecting structural fatigue damage of three common types of rear dump truck are considered. Factors discussed include the effects of haul route features (for example shovel, dump and crusher areas); the effect of operations such as turning, braking, loading and dumping; the influence of payload; the effects of malfunctions in suspensions; and the influence of haul route surface quality. It is shown that with respect to payload, while structural fatigue damage is increased with payload, the structural damage per unit of payload does not change significantly for moderate increases in payload above the nominal value. Finally, on the basis of these results, recommendations are made for haul route design and operational practices which will increase the structural fatigue life of haul truck frames.

Jan 1, 1986

By P. Campbell, E. M. Gardy, L. Hachkowski

Introduction The efficient process control of a uranium mill and its associated mining operation requires a nearly continuous knowledge of the uranium concentration in the ore. Generally, the approach is to use laboratory assays of grab samples from the mill feed belt. In some cases, elaborate and expensive systems have been used to ensure random sampling, but even with these systems, mass-balance discrepancies still exist. There is a requirement for an on-line instrument that can give a prompt, accurate analysis of a large portion of the feed stock. The authors have recently evaluated a laboratory system that achieves these goals using neutron activation and delayed neutron counting. The development of the on-line uranium ore analyzer is a consequence of previous work done at the Whiteshell Nuclear Research Establishment (WNRE) (Campbell et al., 1978 and 1981), and is based on the emission of delayed neutrons after the neutron irradiation of fissionable materials. The mechanism of delayed neutron emission has been described (Keepin, 1965), but briefly is as follows. The fission fragments resulting from irradiation are in an excited state. Certain of these delayed fission products, precursors, decay to a more stable state by the emission of a delayed neutron. The delayed neutrons can be divided into six groups with effective half-lives ranging from 0.2-55 sec. It is important to note that more than 50% of the delayed neutrons are emitted within the first 6 sec after irradiation; this has an influence on the design of the analysis instrument. Measurement Cycle The measurement cycle involves a neutron irradiation, a delay time, and a counting period. The laboratory demonstration model of the ore analyzer comprises a californium-252 neutron source, a source chamber, a pneumatic transfer facility, and a neutron irradiation and counting module [(Fig. 1)]. The ore sample is placed in the irradiation chamber. The neutron source is transferred to the center of the chamber for a 5-sec irradiation while the helium-3 thermal neutron detectors are switched off. As the source returns to the storage chamber, the detectors are switched on and the delayed neutrons counted. The total assay cycle is 16 sec. The current instrument design calls for the ore to be cut from the main belt every 16 sec by a mechanical arm and dropped into the analyzer directly, or via another belt. The cycle starts when there is a sufficient mass of ore in the irradiation chamber to depress a switch and stops when the delayed neutron count is finished. The ore is then dropped through the bottom of the analyzer chamber and returned to the main belt. The counts from each cycle are accumulated and the data reduced to give the desired information.

Jan 1, 1985

By B. D. Thomas

GRAVITY concentration is a general term designating processes for separating and sorting granular material by means of forces that depend on the density, size and shape of the particles. When these forces are applied to the particles the latter are caused to move, those of a given density along one path and those of a different density along another, until ultimately they are sufficiently separated to be removed from the operation of the process. The forces producing this separation are in general complex and, unfortunately, no completely rigorous analysis of them has as yet been devised. The science of the hydrodynamics of viscous fluids deals with the little that is known about the problem. Every observer of nature is familiar with the fact that an object moving in a fluid encounters a force of resistance. We have only to walk against a brisk wind or stir a cup of coffee, or observe the slow fall of a grain of sand in water, to experience directly the fact that such forces exist. The exchange of force between an object and a fluid in which it is moving operates on the fluid as well as on the object. Thus a sailboat may be set in motion by the force exerted by the wind on the sail; but the sail also deflects the wind-furthermore, the water in which the boat floats is set in motion by the force exerted by the boat as it cleaves through the water. The wind is thus enabled to do work on the water through the intermediary of the boat. In general, an object moving through a fluid encounters a force that opposes the motion and also acts to change the motion of the fluid. In gravity concentration we are dealing with this force of resistance acting on the granular particles that are to be separated. Furthermore, the motion induced in the fluid by a particle will in turn affect the motion

Jan 1, 1943

By Y. Lizotte

"This paper examines the application of blasthole sloping to narrow vein mining in Canada, for ore deposits where widths are less than two metres. While the technique has now been utilized for more than ten years, it remains in the experimental stage and on-site testing is necessary for its adoption at new mining operations or in differ¬ent geological settings. It is intrinsically a safer method than other narrow vein methods in current use.The investigation describes the main operating parameters for mines recently surveyed. The criteria for method applicability are defined and the problems encountered are studied. It is concluded that blasthole sloping for narrow vein mining is a viable modern method which promises to gain popularity and that emerging fragmentation technology and blasting research can be used to further increase applicability of the stoping method."

Jan 1, 1991

By A. J. Conelius, D. P. Sobocinski

This paper presents a correlation for predicting the behavior of a water cone as it builds from the static water-oil contact to breakthrough conditions. The correlation is partly empirical and involves dimensionless groups of reservoir and fluid properties and of production and well characteristics. The groups were deduced from the scaling criteria for the immiscible displacement of oil by water. The correlation is based on a limited amount of experimenfal data from a laboratory sand-packed model and on results from a computer program for a two-dimensional, incompressible system. Because the correlating groups are dimensionless, they can be used to estimate the performance of water coning cases not specifically considered in the correlation. However, despite its dimensionless nature, the correlation is not completely general and will not provide meaningful estimates of cone behavior in many situations. INTRODUCTION AND BACKGROUND The production of water from oil wells is a common occurrence which increases the cost of producing operations and may reduce the efficiency of the depletion mechanism and the recovery of reserves. We will deal with one cause of this water production, namely, coning. The coning of water into a producing well is caused by pressure gradients established around the wellbore by the production of fluids from the well. These pressure gradients can raise the water-oil contact near the well where gradients are most severe. Gravity forces that arise from fluid density differences counterbalance the flowing pressure gradients and tend to keep the water out of the oil zone. Therefore, at any given time, there is a balance between gravitational and viscous forces at points on and away from the completion interval. When the dynamic forces at the wellbore exceed gravitational forces, a cone of water will ultimately break into the well to produce water along with the oil. We can expand on this basic visualization of coning by introducing the concepts of stable cone, unstable cone and critical production rate. For instance, if a well is produced at a constant rate and the pressure gradients in the drainage system have become constant, a steady-state condition is reached. If, at this condition, the dynamic forces at the well are less than the gravity forces, then the water or gas cone that has formed will not extend to the well. Moreover, the cone will neither advance nor recede, thus establishing what is known as a stable cone. Conversely, if the pressure in the system is in an unsteady-state condition, then an unstable cone will continue to advance until steady-state conditions prevail. If the flowing pressure drop at the well is suffcient to overcome the gravity forces, the unstable cone will grow and ultimately break into the well. It is important to note that in a realistic sense, stable cones may only be "pseudostable" because the drainage system and pressure distribution generally change. For example, with reservoir depletion, the water-oil contact may advance toward the completion interval, thereby increasing chances for coning. As another example, reduced productivity due to well damage requires a corresponding increase in the flowing pressure drop LO maintain a given production rate. This increase in pressure drop may force an otherwise stable cone into a well. The critical production rate, well known in the literature, is the rate above which the flowing pressure gradient at the well causes water (or gas) to cone into the well. It is, therefore, the maximum rate of oil production without concurrent production of the displacing phase by coning. At the critical rate, a built-up cone is stable but is at a position of incipient breakthrough. Numerous papers have been published on critical rates. Some of the better known of these include the work of (1) Muskat and Wyckoff,' who first dealt with the coning problem; (2) Chaney, et al,' who developed expressions similar to those of Muskat but who presented results in a conven ient-to-use graphical form (the "Sun" method); and (3) Meyer and Garder,b hose analysis is based on radial-flow formulas. One assumption in critical production rate analyses is that the cone has built-up to just before its breakthrough into the well. But, these analyses reveal nothing directly about the time it takes for the cone to build up to this incipient breakthrough position. Thus, water-free oil can be produced from a well for prolonged periods at rates above the critical rate before the well reaches the condition to which the critical rate applies. The published literature contains little on the rate of growth of a cone. Experimentally, Meyer and Searcy studied the rate of rise of a cone in a Hele-Shaw model.' Additional related work on water breakthrough and produced water-oil ratios in water driven reservoirs was reported by Muskat," Hutchinson and Kemp," Henley, et al,' and Stevens, et a1.B Theoretically, the basic coning equations for a water-oil system can be developed by applying the conservation of mass to each of the phases, relating flow velocities with pressure by Darcy's law, and relating pressures across water-oil interfaces by capillary pressure. With the usual boundaries at the well and reservoir limits, the solution of the resulting equations for the time behavior of a water-oil interface constitutes a free-surface, boundary-value problem. The shape of the boundary depends on the internal potential distribution, while this

Jan 1, 1966

By W. H. Bassett

THE modern smelting and refining of copper is distinctly an American development. The present demand for sound and perfect castings for rolling is due to the development of American industry. Prac-tically every article made from sheet metal or, for that matter, from any form of metal is made by mass produc-tion methods. Faulty material disturbs the orderly sequence of operations and in addition requires expen-sive inspection and unbearable rejection of finished product. This demand, therefore, is positive and will have to be met. Some mines produce ore that can be smelted and re-fined without the electrolytic process into satisfactory copper for the wrought metal industry, and some of these ores carry small amounts of impurities that are of use in hardening and toughening the copper. Most of the copper ore mined contains impurities that must be removed and, fortunately, precious metals which are separated at the same time make this re-moval profitable. The modern electrolytic refineries have their methods so well under control that the product meets all re-quirements without question if properly fire refined and cast. The "if" in this case is important, because there is evidence of carelessness or want of control at times in the material from some of the producers. It is nec-essary that the melted cathodes should be saturated with oxide to dispose of sulfur and that the copper should then be poled to the proper pitch or set. Sometimes statements leak out to the effect that it is unnecessary to oxidize completely the molten cathodes and a little less rabbling saves poles, which are expensive. The re-sult is that the rolling mill gets porous castings and produces seamy or slivered sheets or strips. The condition of the molds, their temperature, and the temperature of the metal are all important to good copper cakes, wedges, or wire bars. Cracked, and burned molds leave rough places and porous spots. Molds which are out of shape, or cracked, make shrink-age cracks which gap open when the castings are hot-rolled. Dampness means porosity. Drops of oil mean porous or honey-combed areas. Poor or irregular dress-ing means mold wash in the castings. Cold copper or slow pouring means cold sets.

Jan 4, 1928

Currently there is considerable interest in the production of DRI in Western Australia to take advantage of intense interest from the Asian market. Most DRI is produced using gas-based processes and is used as a feedstock in electric arc steel furnaces, otherwise known as mini-mills. This paper critically examines the technical and economic issues of various gas-based DR processes available today and recommends the most effective and attractive processes suitable for Western Australian iron ores.

Jan 1, 1996