Search Documents

By G. W. Doepel, W. P. Sibley

A three-dimensional, multilayer, mathematical model has been developed for predicting performance by mis-c.ible displacement. Areal and vertical coverage, total gas-oil ratio, propane-oil ratio and oil-recovery factor for the multilayer system are computed as functions of hydrocarbon pore volumes of solvent injected. The technique has been programed for use on the IBM-7090 digital computer and was used in calculating perfortnance for continuous miscible displacement of a five-spot, 50-layer .system. Results reported are based on the use of published laboratory data for a single, uniform five-spot layer. However, the technique is sufficiently generalized to calculate performance of any system of layers of any pattern configuration and mobility ratio, provided data are available to describe perfortilance of a single layer. The technique has also been adapted for predicting oil recovery resulting from various gas-driven slug sizes. The results presented for both continuous and slug-type injection show, that permeability variation has 0 significant effect on oil recovery but that solvent composition, within the range studied, has a lesser effect on oil recovery. INTRODUCTION Experience from many of the miscible-phase displacement projects currently in operation indicates that the injected solvent flows preferentially through the more permeable zones in the reservoir. This preferential solvent flow in the high-permeability streaks results in a reduction of vertical coverage (C,) and an attendant decrease in oil recovery. The multilayer technique presented in this paper uses areal coverage (C.,) data for a single layer from the literature and from laboratory measurements of displacement efficiency (herein referred to as microscopic coverage, C,,) to calculate areal coverage (C,) and vertical coverage (C,) for the multilayer system. Oil recovery for the multilayer system is obtained as the product of (Ca) (Cm) (Cv). It is assumed that C, in a single layer is 100 per cent; therefore, (C,) (Cm) is a measure of oil recovery from that layer. Data presented in the literature for a single layer generally deal only with areal coverage and/or microscopic coverage —but seldom specifically with oil recovery. Nevertheless, this technique is flexible in that either Ca and C,, of an individual layer or a direct measurement of oil recovery for the layer may be used. In developing this technique, the problem arose concerning a method of determining the relative amounts of solvent that will enter each layer during any increment of solvent injected. To solve the problem, a dimensionless equation was derived for expressing solvent injected into each layer as a fraction of total injection. A finite-difference method was applied in integrating the equation to determine oil recovery for the system of layers as a function of pore volumes injected. The technique subsequently was programed for solution on a digital computer. The method was applied to predict performance of a deep California reservoir under continuous miscible displacement and has been extended for calculating oil recovery as a function of slug size for gas-driven slug injection. The technique may be applied to any petroleum reservoir that can be adequately represented as a layered system, by considering permeability variation,1-3 permeability range and average permeability. Each layer is then assigned its appropriate permeability, porosity and hydrocarbon saturation. RESERVOIR VOLUME CONTACTED BY SOLVENT It has been recognized for some time that high microscopic coverage (C,) can be obtained by injecting a miscible agent, such as propane, into an oil reservoir. These high values of C,,, have been demonstrated in the laboratory and are normally between 80 and 100 per cent, depending on solvent and reservoir oil composition as well as on reservoir temperature and pressure. In miscible-phase displacement, because there is no interface between solvent and oil, effective permeability to solvent is the same as that to oil. (This assumes that oil saturation has not changed and that water is immobile.) Consequently, mobility ratio (M) simply reduces to that of viscosity ratio . Perrine4 and Habermann5 have shown that large

By A. E. Wells

"When the United States entered the World War, the heavy requirements for sulphuric acid in the manufacture of explosives made necessary a definite knowledge of the sulphuric acid capacity of the country. The Bureau of Mines, under the authority conferred by the explosives regulation act, made a thorough survey of the sulphuric acid situation. In this work, which was personally directed by the writer, comprehensive data were collected on the situation and capacities of the various acid plants, sources of supply of raw materials (brimstone, pyrite, pyrrohotite, zinc ores and concentrates, waste sulphur dioxide gases from copper smelting, and spent oxide from gas works), the principal points in regard to manufacturing processes (chamber and contact) and the uses of the acid. The results of this investigaion have recently been published by the Bureau of Mines, as Bulletin 184, entitled ""The Manufacture of Sulphuric Acid in the United States"" by A. E. Wells and D. E. Fogg. The following paragraphs on the uses of sulphuric acid are abstracted from this bulletin.Sulphuric acid is one of the most important of all chemicals, not only because of the large quantities manufactured but also because of the wide use of the acid in many different industrial works. Sulphuric acid is to the chemical industry what iron is to metallurgy. The general public, however, does not realize this fact, for sulphuric acid does not appear in the finished product as does iron and steel, but is only a means to an end. It is essential in many industries, such for example as in the manufacture of phosphate fertilizers, explosives, dyes and petroleum products. In recent years in the United States, especially in the East, the demand for sulphuric acid for chemical and metallurgical industries has been an accurate and sensitive barometer of the general business conditions. This demand for acid responds much more quickly to a general slump or boom in the industrial world than does the demand for iron and steel."

Oct 1, 1920

By R. H. Brown

EARLY workers attempted to study the structure of alloys by measurement of equilibrium electrode potentials in aqueous solutions containing ions of the metals from which the alloy was made.1 The method was subject to such limitations (e.g., the difficulty in attaining electro-chemical equilibrium at low temperatures) that it has not been widely used by metallurgists. Recently, Seltz and co-workers have introduced a greatly improved method for studying alloys by measurement of equilib-rium electrode potentials in molten salts.2-4 The mathematical treatment is the same, of course, as for equilibrium potentials of amalgams in aqueous solutions.5 This method will probably find extensive use, since it makes possible not only the deter-mination of phase fields of equilibrium diagrams but also the determination of certain thermodynamic quantities which can be used advantageously in metal-lurgical calculations. However, the method presents difficulties. With many metallic and alloy electrodes, reversibility is not readily obtainable. Also, the difficulty of obtaining suitable material from which to make the cells is increased as the temper-ature is increased. Moreover, the necessity of carrying out measurements in a vacuum requires additional apparatus and intro-duces considerable difficulty, especially at the higher temperatures.

Jan 1, 1940

"A 3-dimensional finite element model for stress/stability analysis of rock excavations in underground mines is presented. Developed for use on personal computer under OS/2 operating system, the model employs the 8-node isoparametric brick element and accounts for such loading conditions as in situ stresses and gravity loading of the rock mass. In addition, modelling of backfill in mine stopes as in situ stress-free material is incorporated. Material failure is assessed by Mohr-Coulomb or Hoek-Brown failure criterion. A mine design example is presented to illustrate the potential use of the model as a tool for stope design.IntroductionNumerical modelling of mine structures has become a vital tool for mine design in recent years. The need to maximize ore extraction ratio and to reach deeper mineral deposits underground has led the mining industry to employ numerical methods of analysis to undertake complex ground control studies in order to better understand the ground response to mining excavations and to evaluate the ground support requirements. Thanks to the rapid developments in computer technology, it is now possible to perform very comprehensive analyses including, but not limited to, 3-dimensional, elasto-plastic, or large deformation or time dependent nonlinear analyses on personal computer.During the past ten years or so, many researchers undertook 3-D finite element analyses of rock mechanics problems in mining engineering. The following is only a sample review. For example, Chan'!' used three-dimensional finite elements to study the mechanical response of jointed granite during shaft sinking at the Canadian Underground Research Laboratory. Wang et al.(2) performed 2-D and 3-D finite element analyses of room-and-pillar mining system with flat and rolling coal seams. Thatejatu used three-dimensional finite element method to examine the problem of branching tunnels. Dolezalovaw used three-dimensional finite elements for the analysis of tunnel-face advance with partial excavation as well as full-face excavation in combination with rein for cement of the face by long anchors. Peili (5) used three-dimensional finite elements for the simulation of rock-liner interaction near the tunnel face."

Jan 1, 1992

By Raymond M. Stateham

The Bureau of Mines has developed a portable, lightweight device for determining the integrity of resin-grouted roof bolts. The instrument functions by sending a known pulse of ulstrasonic energy into the bolt and comparing the amount of energy reflected hack with the original measured pulse. Where the bolt is properly bonded or coupled with the rock, the energy passes through the bolt-resin-rock interface and dissipates in the rock. Where the bolt is not properly coupled, the energy is reflected back along the bolt to the instrument. The ratio of reflected energy to the pulse approximates the fraction of the bolt's surface that is improperly bonded. The instrument is easy to use. The operator holds the sensor head of the device firmly over the head of the bolt to be tested, causing the pulse of ultrasonic energy to be imparted to the bolt. The device then listens for reflected energy. This cycle is repeated about 200 times per second until an evaluation of the bolt installation is made and indicated by colored lights in the display window. Bolts having 50% or less of their surface bonded are considered had and cause a red light to he illuminated. Bolts with 50% to 75% of their surface bonded cause a yellow light to be lit and are considered marginal. Bolts having more than 75% of their surface bonded are considered good and cause a green light to be lit. The indicator lamp remains on for about 4 seconds and then goes off, indicating that the instrument is ready for another test.

Jan 1, 1982

By R. S. Adhikari

The changes in defects patterns or in element condition index during visual inspection of bridges are primary concerns for inspectors. This paper presents a new approach for change detection of defects in bridges by identifying changes in texture patterns through spectral analysis of digital images. The commonly used method for change detection is image differentiation. This subtraction method requires images to be of same size, scale, and rotation. However, no two images are same in real practices. Thus, image registration is required to align images and to produce change maps. This process is tedious and it is difficult often to achieve a good registered image. But, the change detection task can be readily modeled in frequency domain for texture patterns discrimination and also for quantifying their properties. This paper proposes a novel approach for change detection by transforming digital images into Fourier spectrum. In new coordinate system, 1-D signature functions can be drawn which facilitates easy comparison of textures in different directions. The proposed methodology provides useful tools for comparison of inspection history graphically and quantitatively. In practice, expensive sensors are used to detect subtle change in defect patterns. The proposed method can be used to detect any subtle change in defect patterns using digital images at much lower cost.

Aug 1, 2013

By L. H. Levenson, Charles S. Barrett

Since 1925, when the preferred orientations in compressed aluminum were first determined1,2 the orientations have been described as a fiber texture in which a face diagonal, [110], of the face-centered cubic lattice is parallel to the compression axis. Subsequent experiments have seemed to confirm this texture,3-5 and a number of theories (recently summarized in references 6 and 7) have been proposed to explain it and to relate it to the behavior of single crystals during compression.3,8-11 The experiments reported in this paper prove that the orientations are not adequately described as quoted above—i.e., as a [110] fiber texture—although this is a first approximation to the actual texture. They also show that the texture cannot be thought of as a stable orientati011 that is reached and maintained after a sufficient amount of deformation. The actual texture, when studied in detail at successive stages of compression, indicates that a hitherto unsuspected range of orientations is present, both in the polycrystalline metal as a whole and in various individual grains in its interior, and that a state of dynamic equilibrium exists within this range. The reasons for the failure of previous theories to predict the actual texture become obvious when the heterogeneous nature of the flow is considered. In addition to the deformation texture, the manner of its development, and its theory, this paper presents data on the following related subjects: the identity of strain markings in aluminum; the orientation changes in aluminum single crystals during compression and a comparison of these with the conditions in individual grains of a polycrystalliile specimen; the origin of asterism ill deformed single crystals, which heretofore has been regarded as a distortion localized at the surfaces or slip planes; and the relation of plastic strain in individual grains ill all aggregate to the strain of the whole.

Jan 1, 1940

By Charles S. Barrett, L. H. Levenson

Since 1925, when the preferred orientations in compressed aluminum were first determined1,2 the orientations have been described as a fiber texture in which a face diagonal, [110], of the face-centered cubic lattice is parallel to the compression axis. Subsequent experiments have seemed to confirm this texture,3-5 and a number of theories (recently summarized in references 6 and 7) have been proposed to explain it and to relate it to the behavior of single crystals during compression.3,8-11 The experiments reported in this paper prove that the orientations are not adequately described as quoted above—i.e., as a [110] fiber texture—although this is a first approximation to the actual texture. They also show that the texture cannot be thought of as a stable orientati011 that is reached and maintained after a sufficient amount of deformation. The actual texture, when studied in detail at successive stages of compression, indicates that a hitherto unsuspected range of orientations is present, both in the polycrystalline metal as a whole and in various individual grains in its interior, and that a state of dynamic equilibrium exists within this range. The reasons for the failure of previous theories to predict the actual texture become obvious when the heterogeneous nature of the flow is considered. In addition to the deformation texture, the manner of its development, and its theory, this paper presents data on the following related subjects: the identity of strain markings in aluminum; the orientation changes in aluminum single crystals during compression and a comparison of these with the conditions in individual grains of a polycrystalliile specimen; the origin of asterism ill deformed single crystals, which heretofore has been regarded as a distortion localized at the surfaces or slip planes; and the relation of plastic strain in individual grains ill all aggregate to the strain of the whole.

Jan 1, 1940

By Louis W. Cope

Placer material, regardless of the value of gold, tin, titanium, diamonds or other value mineral it contains, remains worthless until the valuable constituent is separated from the bulk of the material. This separation is no mean task when considering that a gold placer containing 0.01 to 0.03 oz/yd3 of gold, which is the range of grade of typical placer deposits; yes, 1:3,000,000! It is a miracle that gold placer mining has ever been profitable. Added to the situation of minute quantities of gold are several other problems, such as the gold often being very finely divided, the association of boulders and clay, and running and/or ground water. As each placer deposit is individual and distinctive, many factors have to be considered in planning the method for gold recovery from the alluvial deposit. Previous chapters have shown that in the exploration and sampling stage, some knowledge of the amount of each size of coarse and fine material which occurs in the deposit as well as the size distribution of the discrete gold particles is determined. Unless informed to the contrary, as a general rule of thumb, plant designers will consider that 40 percent of the material will pass through a 5/8-inch screen or punched plate hole. Also that there may be an occasional nugget and normally considerable amounts of fine gold. The designer must

Jan 1, 1992

By S. A. Kenzap

This paper provides an overview and discussion of key aspects of operating risk valuation in underground metal mining systems, with impact on project economics, using stochastic computer modelling in Discounted Cash Flow (DCF) analysis. Mine operating risk classification and assessment for ground, equipment and scheduling aspects are presented with an overview of available risk valuation tools that have been developed in engineering disciplines. The classification is organized by keeping in perspective the mine design needs and constraints, as well as the potential economic impact that operating problems can have on an underground development and production system. These sources of cost, revenue and time delays are tabulated to enable the hierarchization of potentially hazardous unplanned events occurring during the mining project life cycle. In complex technological systems, like the underground mining systems, the decision-making process involve a wide range of uncertainties, and often this is based on subjective and qualitative expert evaluations. Whether a qualitative or quantitative analysis is conducted, it is often the case that the probability of a certain project parameter value needs to be estimated. This requires use of methods and techniques to handle subjective, qualitative measures and to combine them with quantitative stochastic modelling in order to evaluate mine operations-related issues on DCF economic performance measure parameters. Links are established between decision making and the risk-based mine planning process for evaluation of design alternatives, with emphasis on the need of introducing flexibility in mine design. Finally, challenges of risk-based mine planning and design implementations are discussed and the call for an integrated risk-based real options systems valuation (ROV) ?in? projects analysis is made.

Aug 1, 2013

By G. M. T. Marshall

Plans to bring the Geco Mines property in Manitouwadge, Ont., into production began in 1954. At that time over 12 million tons of copper-zinc ore were indicated in a zone 2700 ft long. A concentrating plant was built to handle 3300 tpd of ore and a production shaft was sunk about 1500 ft. MINE LAYOUT Vertical attitude, width, rake, and competent country rock of a 4-million ton orebody west of the main diabase dike suggested a system of blasthole stopes, undercut with scram drifts connected by a transfer raise system to a crusher on the 1250-ft level and this system was employed. A 42-in. conveyor on this level transfers the ore about 1200 ft to a loading pocket at the No. 1 shaft. The system has a number of advantages: 1) Cost of tramming is eliminated. 2) Rate of extraction from any stope is controlled only by the scraping capacity of the scram. 3) Rate of extraction from the stoping area can be very rapid. Fast extraction makes it possible to cut mining costs for the following reasons: The number of stopes actively producing is kept to an economical minimum; the operating area is concentrated-manpower can be used more effectively; and active life of the stoping block is short, making ground support problems simpler and less costly.

Jan 8, 1959

By B. T. Brady

Experimental data 1,2 on the energy dissipation in polycrystalline materials over a large frequency spectrum (10-2 cps to 106 cps) suggests that the quality factor [(e= Q )] is independent of the frequency providing both fluid-saturated and ferromagnetic materials are excluded from the test data. Additional data 3 suggest that the quality factors are less at high pressures than at low pressure, i.e., Q increases as the pressure increases. Observations on the dissipation of single quartz crystals with their polycrystalline counterparts indicate that the energy dissipation is less for the single crystal than for the aggregate .2 Both of the above observations, particularly the latter, are indicative of the fact that the dissipation increases with increasing surface contact within the polycrystal, i.e., a frictional attenuation scheme may be operative. Knopoff and MacDonald 4 have shown that a friction model gives rise to a quality factor frequency independence property. A partial listing of some values of Q, observed for both metals and non-metals, is given in Tables I, II, and III. In Tables I and II, the data all show Qs>Qp, i.e., the energy loss per cycle for compressional body waves is greater than that for shear waves of the same frequency. Most samples in Table III show the same effect. It is objective of this paper to suggest: (1) a frictional attenuation scheme may account for the observed losses incurred during the propagation of low amplitude stress waves in dry brittle rock and, in particular, that such a scheme can account for the observed relative magnitudes of the quality factors for P and S wave motion; (2) a friction scheme can readily explain the difference between the dynamic and static moduli in dry brittle rock; (3) a friction scheme, while in itself an intrinsically

Jan 1, 1968

By E. B. Hunt

Paraffin deposition has been studied in the laboratory under conditions simulating deposition in well tubing. A theoretical analysis has been made of the cooling of the oil and the precipitation of paraffin from the oil as it flows up the well tubing and through surface flowlines. It is proposed that paraffin deposits are initiated by the precipitation of paraffin directly on or adjacent to the pipe wall and grow by diffusion of paraffin from solution to the deposit. This mechanism is consistent with laboratory and field observations, and has proved useful in the design and interpretation of laboratory paraffin-deposition tests. Tests have been made of the effect of plastic pipe coatings and chemical additives on paraffin deposition. INTRODUCTION Paraffin deposits which form in well tubing and surface flowlines interfere with production and must be removed. Over the years much progress has been made in developing and improving methods of removing these deposits after they form. Much less progress has been made in developing methods of preventing or inhibiting the formation of paraffin deposits. This is due, it is believed, to the lack of knowledge of the mechanism of paraffin deposition, the absence of satisfactory laboratory testing methods and the difficulties in evaluating the results of field tests of preventive treatments. The present investigation was undertaken to elucidate the mechanism of paraffin deposition and to develop suitable laboratory tests for studying the inhibition of paraffin deposition in well tubing and surface flowlines. Current theories on the mechanism of paraffin deposition have been evolved from field observations, from laboratory studies of various factors which might be involved in paraffin deposition, and from laboratory paraffin-deposition tests.1-9 Paraffin deposits have been formed in the laboratory by immersing a cold finger into a hot wax-oil solution and by flowing hot wax-oil solutions through cooled pipe or over cooled plates. These laboratory conditions differ in important features from field conditions, and the observed deposition behavior is not entirely field-like." Thus, there is reason to question the field applicability of the results of these tests. The present investigation was undertaken to determine how to perform and interpret laboratory paraffin-deposition tests to obtain information on the inhibition of deposition in the field. The paraffin problem in the broadest sense encompasses the formation of any predominantly organic deposit in well tubing, surface flowlines and other equipment in contact with crude oil or gas. The present investigation was limited to paraffin deposition involving the precipitation of paraffin wax from solution by cooling and its concentration in a deposit on a cooled surface. This probably excludes its applicability to those problems arising from asphaltic-base crudes, but not those arising from paraffin-or mixed-base crudes. This also excludes its applicability to emulsion and congealing oil problems which are often included as part of the paraffin problem. The phenomenon of cooling appears to be the controlling factor in paraffin deposition involving the precipitation of paraffin wax and its concentration in the deposit. Deposits of this type are usually found in the field only where cooling occurs. Early in this laboratory investigation, it was not found possible to form deposits under constant temperature conditions from a wax-oil slurry, either by steady flow through pipe or by gas-lift up a pipe. Thus, the investigation was limited to situations involving cooling. THEORY The relationships involved in establishing the temperature profiles in an oil stream as it flows up well tubing with a linear (geothermal) pipe-wall temperature distribution or through surface flowlines with essentially constant pipe-wall temperature are presented in the Appendix. The relationship between radial distance in the pipe and the rate of cooling of the oil is then combined with a relationship between cloud point and rate of cooling to develop the pattern of formation of a wax cloud in the oil. The following discussion of paraffin deposition under various laboratory and field conditions is based upon this development which is presented in the Appendix. PARAFFIN DEPOSITION IN SURFACE FLOWLINES The average temperature of the oil coming out of a well is somewhat higher than the ground temperature. Thus, the oil continues to cool on its trip through the surface flowline, and wax deposition can occur. The temperature distributions calculated from Eq. A-4 are given in Fig. 1. As can be seen, almost all the cooling occurs in the first 500 ft from the wellhead. In addition, the radial temperature gradient near the wall decreases rapidly with distance and becomes very small after a few hundred feet. Thus, growth of a paraffin deposit would be expected to decrease rapidly with distance from the wellhead and become negligible after a few hundred feet, since growth is dependent on concentration gradient. Wax precipitation and diffusion of wax to the already

By Wright G. A

The objective of refining in steelmaking is to reduce the concentration of impurity atoms, e.g. sulphur, phosphorus, from an initially high level to a specified low concentration. A two-film theory of refining is presented in which the rate of

Jan 1, 1980

By John Bailey

Stressmap is a program whereby the earth's stress field is charted in detail and utilized for design of mines and mine exploitation. This program is implemented by mapping the attitude (location, direction, dip, and extent) of induced rock ruptures during the process of hydrafracturing drill holes contiguous to mine interest. The program includes utilization of ancillary naturally occurring stress relief signals, They are precipitated because the earth is indeed dynamic and the strata of the crust are continually adjusting to load and/or strain differentials resulting in rock deformation and fracturing. These fracturing adjustments occur as small to tiny earthquakes comparable to Richter magnitudes of one, zero, minus one, and smaller events termed microearthquakes. Obviously, the earth's stress field changes due to continued differential loading and crustal movements; therefore it becomes conspicuously evident that resolving today's stress field as opposed to paleostresses is most important for efficient, economical, and safe mining operations.

Jan 1, 1974

By J. A. van Huyssteen, P. H. Radcliffe

With the profit squeeze of recent years and indeed the survival of many mines at risk due to low gold prices and declining grades, many inventive solutions have been found of increase production and decrease cost. One of these is the application of process auditing methodology which is essentially a tool to determine systematically whether a process is delivering optimally and, if not, to identify the basic causes. Then a prioritized action plan can be developed with the client. Our experience has shown that problems are seldom what they appear to be and that most processes can operate far more efficiently with relative little effort. A process auditor requires good facilitation skills to overcome initial suspicion, and for sustainable solutions client involvement is essential. Process auditing as it is being applied in Anglogold has evolved over many years to reach its current format. The lessons learned and insights gained in the process are shared here with the reader.

Jan 1, 1999

By D. J. Barrett, M. A. Sochocky

INTRODUCTION Summary of Factors Influencing Comminution Circuit Design The selection of an appropriate comminution circuit for a specific ore is one of the most important decisions in the design of a processing plant. The importance is related to the fact that the capital and operating costs for crushing and grinding plant generally represent, as is well known, the major portion of the plant costs. This chapter will, therefore, identify as many as possible of the factors which influence the selection of a comminution circuit. The number of factors which will have to be considered for any comminution project will depend, among other things, on the type of project. If, for example, the project is an entirely new mining development, then most, if not all, the factors identified will have to be analyzed. If the project is an expansion of a developed mining operation or if the new orebody is adjacent to a viable operation, then the existing operation will influence the choice of factors or design constraints which need to be considered. The existing infrastructure or supporting systems may be quite adequate to accommodate the requirements of any expansion or new development. Hence, those factors may not have to be considered. To cover, however, the widest spectrum of projects, the factors which have been identified in this chapter are those which will have to be considered for the most complex of projects, that of developing an entirely new mining operation. The range of factors is as broad as the range of different ore types. Thus, each development must be treated with individualized care. The most important step in the development is the analysis and understanding of the ore characteristics. The hardness of the ore, its abrasiveness, friability, moisture content, grade, mineralization including gangue mineralization, liberation size, chemistry, and other characteristics should be the first to be analyzed in the investigation. The next should be the determination of factors such as plant size, throughput, location, climate, accessibility, and availability of water. The selection of samples for initial bench scale work and bulk sampling (when needed) for further

Jan 1, 1982

By Clinton L. Miller

MINING operations have been carried on in the immediate area of the Elizabeth mine during periods of high copper prices since 1793, when copperas and vermillion were first won from the outcrop. Present operations started in 1942 as a war baby. Since then production has totaled 1.7 million tons of 1.8 pct Cu ore. Elizabeth mining operations are on a pyrrhotite- chalcopyrite orebody contained in a gently plunging amphibolite syncline. The oreshoot varies in width from 10 to 40 ft, and in the area under consideration is about 150 ft in vertical extent, and more than 1000 ft long. Surface pits or cuts have been worked in three areas along the outcrop, with one pit just completed and a second in full production. Present production is 24,000 tons per month, of which 6000 to 7000 tons is trucked from the open pit.

Jan 11, 1954

By Felipe P. D. Lopes, Ailton Silva Ferreira, Sergio N. Monteiro

"Environmental issues such as global warming and water pollution are motivating fast changes in scientific and technological paradigms. Special importance is now being given to the so called environmentally friendly materials, which are renewable, recyclable and biodegradable. An example is the natural fibers with increasing industrial applications beyond the conventional uses as baskets, fabrics, ropes and carpets. In addition to traditional natural fibers, others like curaua (Ananas erectifolius) are being investigated for possible use as reinforcement of industrial composites. Since epoxy matrix is not yet incorporated with curaua fibers, the objective of this paper was to study the basic properties of epoxy composites reinforced with different amounts of curaua waste fibers. A comparative analysis aiming at the use of these composites as substitute for conventional building materials was carried out.IntroductionThis new millennium, which initiates with the 21th century, is experiencing a fast degradation of the environment by pollution and climate changes. Most of the problems are related to our methods of development associated with the use of fossil fuels and the energy intensive processing and production of synthetic materials. As a consequence, environmental issues such as global warming and ocean pollution are motivating rapid changes in technological paradigms. One relevant example is the current importance given to natural materials like the lignocellulosic fibers extracted from cultivated plants or found as industrial wastes [1]. These fibers are considered environmentally correct alternatives to substitute energy intensive conventional synthetic fibers such as carbon, glass, nylon and aramid. In addition to the renewable recyclable and biodegradable nature of the lignocellulosic fibers, the low cost and abundance in developing regions are major advantages that justify their increasing application as reinforcement of composites [2,3].In fact, nowadays, the use of natural fibers is no longer restricted to baskets, ropes, clothes and carpets. Industrial composites are introducing these fibers in large technological segments associated with car making, building construction and furniture [4,5]."

Jan 1, 2008

By C. S. Trewin

ZINC, in its wrought form, is produced commercially in rolled strip, sheet, wire, rod and tubing. Wire has been made periodically, but due to the fact that slight drafts are necessary, the cost of production is greater than for the more common non-ferrous metals which are made into wire. Notwithstanding the cost, zinc wire has certain special uses for which it is particularly adaptable. Rod has been made both by rolling and extrusion, the product, however, has not indicated great commercial value. Tubing has been made from strip from time to time by forming a strip around a mandrel and either electrically or gas-welding a longitudinal joint. Recently a tube manufacturer has succeeded in making a fair quantity of this material. Its commercial adaptability is still to be determined but anyone who desires it can obtain quantities of the smaller sizes. Inasmuch as strip and sheet are commercially the most important, this paper will be devoted to these products. In the broader sense, zinc is not alloyed. That is, there are no combinations comparable to the various copper, aluminum and nickel alloys. It has been recognized,, for some time, that the lead and cadmium occurring with commercial zinc have some effect on its properties and such alloys as may be said to exist are those made from zincs containing varying amounts of lead and cadmium with a relatively low iron content. The foreign rolled zinc will analyze higher in lead than the domestic grades. A representative foreign analysis will run 1.1 per cent. lead, 0.07 per cent. cadmium and 0.02 per cent. iron. The American grades vary from zinc approximating high grade. and analyzing 0.08 per cent. lead, 0.002 per cent. cadmium and 0.015 per cent. iron, to the lower grades in which the lead will vary from 0.3 to 1.0 per cent., cadmium from 0.10 to 0.5 per cent. and the iron in the neighborhood of 0.02 percent.

Jan 1, 1927