Search Documents

By E. C. Babson

In order to explore the possibility of predicting reservoir performance from laboratory data, behavior of a hypothetical low-permeability reservoir has been estimated by applying data and methods currently available in the literature. A method of calculating decline in productivity index is discussed, and recoveries by internal gas drive, external gas drive and water drive are estimated. Introduction During the life of a producing oil property an operator is faced with many perplexing problems. Any attempt to determine proper well spacing, optimum rate of production, or the desirability of pressure maintenance requires the evaluation not only of a host of economic and practical operating factors but also of the future performance of the reservoir. Although in some cases economic or operating con-siderations may be of primary importance in planning a development or production program, the anticipated effect on ultimate recovery is more likely to be the decisive factor. The soundest basis for evaluating reservoir performance is past experience with oil fields, but pertinent data are difficult to obtain or apply under conditions normally encountered in California fields. Many of these fields are characterized by thick sections of alternating sands and shales complicated by faulting and rapidly changing lithologic conditions. Further compli- cations are introduced by haphazard development and production practices resulting from competitive conditions, changing demand for oil, and insufficient knowledge of structural conditions during early development. Even in the rare cases where development has been systematic and adequate, production policy has usually been controlled by economic and competitive factors rather than a desire to obtain information for use in future operations. In other words, comparable reservoirs in which development and production practices have been systematically varied are seldom found. In the light of these conditions, conclusions based on experiences usually lack the certainty required for decisions involving large sums of money. Some other method of attacking these problems is needed to supplement and orient field experience. Progress in laboratory investigations of the flow of oil, gas, and water through sands has been so rapid in recent years that these data may furnish such a supplementary approach in the near future. In order to explore this possibility the author has attempted to predict the behavior of one type of reservoir by applying published data and methods. Basic Data and Assumptions Calculations outlined in this paper are dependent upon a detailed knowledge of the properties of oil, gas, and water present in the reservoir and the portion of the total pore space originally filled by each. It is also necessary to know how the permeability of the sand to oil, gas, and water varies with the saturations of these fluids 20

Jan 1, 1944

By K. Reipas

"Westmin Resources Ltd. operates the 3300 TPD H-W underground copper/zinc mine on Vancouver Island. Ore storage underground is handled in a 6000 tonne coarse ore bin and a 3000 tonne fine ore bin. Both of these bins have experienced significant wear since excavation and construction in 1985. Wear problems have included both deteriorating rock walls as well as worn out steel liners and concrete at the discharge points from the bins. Extensive rehabilitation work was completed in 1993.The basis o/this paper is the rehabilitation work done on the coarse ore bin. The design and installation of ground control measures are discussed. The bin access methods used to allow the work to proceed quickly and safely are also presented. This involved the use of a Tekfoam safety bulkhead to protect workers.IntroductionMine DescriptionThe H-W mine was commissioned in 1985. Mine access is by vertical shaft with most production areas at a depth of about 500 m. Host rocks are composed of andesite and rhyolite. Mine capacity of 3300 tonnes per day is achieved mainly by longhole open stoping methods, complemented by room and pillar mining. Metals recovered from the massive sulphide ore are copper, zinc, gold, and silver. Mineable reserves at January I, 1994 were 9.7 million tonnes."

Jan 1, 1995

By Charles L. Kimbell

Annual global steel industry investment is partly mirrored in the data for selected market economy countries that appear in table 13 for 1988-90. No reasonably comprehensive 1991 data were available for inclusion in this study, and the partial reporting available was so incomplete that it was impossible to demonstrate whether the level advanced or declined from the 1990 level of nearly $15.5 billion. Moreover, with the radical changes that are now being effected in the steel industries of the states that were the U.S.S.R. and its CMEA partners, it is most regrettable that comprehensive and comparable data, both current and historic, on investment in this area are not available. Updated information on market economy country petroleum industry capital and exploration expenditures by geographic area has been included in table 14, and it is evident that there was a substantial upturn in investment in 1991. The level of almost $74.5 billion was 14.5 % above the 1990 level and included gains in every topical category and geographic area. The source of information for this table has been changed to the Oil and Gas Journal Database from the previously used Chase-Manhattan Bank study of Capital Investments of the World Petroleum Industry, which has been discontinued. Because of this source change, it has been necessary to modify the structure of the table somewhat, but its total scope of coverage is regarded as basically unchanged. It should be noted that the grand total, as well as some of the detail appearing for 1987, corresponds precisely with those in the previous source.

Jan 1, 1993

By Pierre M. Gy

The final purpose of exploration is to esti- mate the grade and tonnage of the various qualities of ore contained in a given mineral deposit. This estimation cannot be directly carried out on the whole of the ore body. It usually requires four steps: Core Drilling Campaign The ore body is represented by a series of cores further divided into core sections of equal or unequal length. Core Splitting The core sections are longitudinally split into two halves: the first half is kept for various examinations and physical measurements, and stored for further reference; the second half (core sample) is used for determination of the chemical analysis. Core Sample Reduction The chemical analysis cannot be directly per- formed on the core samples. It requires the constitution of assay portions usually weighing from a few decigrams to one gram (more in precious metals assaying) and passing through a 100 or 150 mesh screen.

Jan 1, 1979

By Z. C. Liu, F. F. Roxborough, Lin. B. B.

The size distribution of coal cut by a mining machine is an important performance factor. It is well established that the main machine system variable that affects product size is the depth of cut. In essence, the greater the amount of coal won by a machine cutting at shallow depths, the greater the proportion of dust and fines produced. Conversely, deep cuts produce less dust and a generally larger product size. When cutting with a rotating drum, as well as with a longwall shearer, the depth of cut always varies from zero in the vicinity of the roof and floor, where most of the dust and fines are produced, to a maximum at mid-drum level. In this paper, minimizing the amount of shallow cutting with a cutting drum is discussed, and the effects of the drum cutting and design parameters on cross-sectional cutting area per revolution are analyzed. This study shows the following: •more shallow cutting occurs during the entry quadrant of a cutting cycle than during pick exit; •the ratio of the projected area of shallow cutting to the total projected area of cutting by a single pick per drum revolution is virtually the same for drums of different radii (however, it decreases as the maximum depth of cut increases); and •for double drums, the use of unequal drum diameters can reduce the production of dust and fines, compared to using drums of the same diameter.

Jan 1, 1998

By William Marsh Baldwin

[Two of the most useful and important equations available to the metallurgist for the study of plastic deformation of metals are the Huber-von Mises-Hencky1-3 and the St. Venant7-10 equations. HUBER-VON MISES-HENCKY EQUATION The Huber-von Mises-Hencky equation answers the question: When does plastic flow occur in metal that is subjected to a multi-axial stress? It occurs, according to this equation, when the three principal stresses,? al, a2, and a3 satisfy the equation: (s1 - s2)2 + (s 2 - s 3)2 + (s 1 ? s3)2 = 2K2 [I] Here K is the yield strength of the material as determined in an ordinary tensile test. If the quantities a1, a2, and a3 are assigned to the coordinates of a Cartesian three-dimensional system, this expression describes a cylinder whose axis of symmetry is inclined at equal angles to the three coordinate axes4,5 (Fig. I). The radius of this cylinder is v2/3K. For the purpose of simplicity, it is sometimes advantageous to ascribe the values s 1/K = si, s 2/K = s2, s 2/K = s3 to the three coordinate axes instead of the principal stress alone. In this case, Eq. I becomes (s1 - S2)2 + (S2 - S3)2 + (Sl - S3)2 = 2 [2] and the radius of the cylinder becomes 2/3v. In the latter method of representation, a point lying inside the cylinder indicates that the metal will react elastically, whereas a point lying on the cylindrical surface indicates that the metal will behave plastically. Some of the geometric features of this cylinder are worthy of study. Let us inquire first as to what interpretation may be placed upon what we will choose to call the "circles of latitude" of the cylinder (L in Fig. I) and the "meridians" of the cylinder (M in Fig. I). Circles of Latitude Circles of latitude are formed by allowing a plane, passing perpendicular to the cylinder axis, to intersect with the cylinder. Any point, P, on this circle is presumed to have the coordinates s1, s2, and s3. The coordinates of the point resulting from the intersection of the plane and the cylinder axis will be a, a, and a (since the cylinder axis is equally inclined to the three coordi¬nate axes). Let us now pass a line through the point on the circle and the point on the axis.]

Jan 1, 1946

Henry C. Carlisle: This is a husband-and-wife act, in which Mary Carlisle is going to listen, and break in as often as she feels like it. I am going to describe my career as a mining engineer. We are at Nantucket, in the 75 Main St. house; The year is 1959. Q: This is something the boys and I have wanted you to do for a long time. Carlisle: After leaving Columbia in 1910, I arrived at Ray, Ariz., January 1, 1911, and rustled a job from Louis Cates, Ralph Nowland and Sprott Boyd, who were running the Ray mine. I went to work as a surveyor's helper, made $90 a month, and paid $35 a month board. I lived in a dormitory where about 25 other engineers, graduates from different colleges, were living. It was very social and you made a lot of young friends early in the game. I did not think much of the idea of being a surveyor, or even a surveyors, helper; the higher-up surveyors only got $125 a month, and had been there quite a long time. So, I asked to be changed to underground sampling, where I would see the mine faces every day and learn more about mining. In about three months, I became an underground sampler and remained at this for a year, but in three months I was promoted to head sampler, with six people under me.

Jan 10, 1963

By Bowden MW

Sintering of lead-zinc concentrates is practised by Sulphide Corporation to provide both desulfurised lump sinter feed, for simultaneous reduction to zinc and lead in the Imperial Smelting Process blast furnace, and sulfur dioxide gas for sulfuric acid manufacture.Moisture control of feed mixes is of paramount importance in the sintering operation and improvements in this area have realised increases in overall plant performance.

Jan 1, 1985

By W. J. Jordaan

The ability of soils to retain and hold cations is called the cation exchange capacity (CEC). Adsorbed cations, however, can be replaced by other cations through the process of cation exchange. Heavy mineral deposits contain a significant portion of slimes including the very fine clay minerals. In most circuits the slimes fraction hampers efficiency and has to be removed during early stages of the process. Being a nonvaluable process stream, the processing of the slimes is a costly exercise. In thickening applications it might be possible to manipulate the ability of clay minerals to retain and hold positively charged cations in order to optimize flocculation and therefore reduce flocculation costs. The CEC value of the slimes could be a measure of this possibility. To investigate this hypothesis, different slimes samples were characterized for size, chemical composition and clay minerals present. The CEC value of each sample was determined and explained in terms of the mineral phases present. Settling tests were conducted and an attempt was made to explain the CEC characteristics of the clay minerals in terms of settling rate. The scope of this investigation was to test the hypothesis and should not be seen as an in-depth study of the subject matter. A greater number of samples and detailed analyses to identify and quantify minerals and phases present would be required to investigate further the relationships between clay minerals in the deposit, CEC and settling rates. Location and geological setting Exxaro KZN Sands is mining a heavy minerals deposit at Hillendale mine located at Richards Bay, South Africa. The orebody consist of a dune some 8 km inland from the coast to the north of eSikhawini. A geological synopsis undertaken by Botha1 concluded that the Hillendale mining area represents a coastal dune sequence that accumulated north of the Tugela River. The northward movement of sediment by long shore drift currents result in a high sand budget on the beaches north of the river youth and is the dominant contributing factor to the accretion of the coastline and development of parallel dune systems along the coastal zone in this area. Beach swash zone processes and enrichment of the fine sand fraction occurs during wind transport off the beach by ascending parabolic dunes that form the coastal barrier dunes. This process results in heavy mineral concentration on the windward dune face and localized enrichment parallel to the dune forms. The aeolian sedimentary facies processes result in the primary concentration of higher grades in the upper silt-enriched reddish brown horizons of the profile. The synopsis by Botha1 further showed that an additional component of heavy mineral concentration can be ascribed to the post-depositional relative enrichment of heavy minerals due to weathering. Therefore, it is likely that the Hillendale orebody protolith was pedogenically weathered to form the homogeneous, silt-enriched, clayey reddish brown to dark red, palaeosol profile that grades downwards into yellowish brown, less clay-enriched sand. Slimes characterization Samples The Hillendale orebody was divided into geochemically discretized zones based on the concentration of ilmenite and other specific minerals and/or phases. Six composite samples were made up from exploration samples taken from Zone 9, Zone 11 and Zone 12. The red and orange horizons within these composite samples were separated and test samples were prepared to conduct test work and analyses. The test samples were submitted for preparation and analysis to characterize the slimes properties. Each test sample was deslimed at 45 µm representing the slimes fraction (-45 µm) and dried at 40°C. The -45 µm slimes samples were then split to conduct size analysis, chemical analysis, XRD and to determine the CEC. Size analysis The size distribution of the composite samples is shown in Table I. The size analysis shows that there is a difference in size distribution between the orange and red horizons of each zone. The orange horizons contain less 850 µ material as well as less slimes (-45 µm). The red horizons contain yore slimes (-45 µm). The size distribution of the slimes fraction (-45 µm) was determined using Malvern size analysis. The cumulative particle size distribution of the slimes is shown in Figure 1. The red horizons of the different zones show similar size distributions. The orange horizons show some differences. However, there is a difference in size distributions between the red and orange horizons.

Jan 1, 2007

By C. M. Haight

The mines of the New Jersey Zinc Co. in New Jersey, are situated in the northern part of Sussex County, at Franklin, formerly Franklin Furnace, and also at Ogdensburg. The mine at Ogdensburg is still in the development stage, but the, mine at Franklin, with which this paper deals chiefly, has been a steady producer of high-grade zinc ores for many years. The town is about 50 miles from New York City, among the foothills -of the Kittatinny Mountains. It is equipped with water supply (filtered and chemically treated), good roads, electric lights, efficient police protection and excellent schools, including a new vocational high school. For a mining community, the conditions and location are far above the average. Franklin Furnace Folio, No. 161 of the U. S. Geological Survey, describes the geology and mineralogy of the district in detail, so that merely an, outline of the main characteristics of the orebody need be given. The

Jan 10, 1917

The mixer that is commonly encountered in hydro metallurgical operations consists of a single turbine and tank combination. However, it would be advantageous to examine some common solvent extraction mixing systems in the light of the fundamentals of chemical reactor design. The basic concepts of reactor design are commonly used in the chemical industry, and it should not be too difficult to apply them to solvent extraction. The factors that affect the engineering design of a reactor are: the reacting system; the type of reaction; and the configuration of the reactor. The reaction system in solvent extraction consists of a heterogeneous liquid phase, involving two immiscible liquids. It is essential f or the process that the reactor product can be separated efficiently in the subsequent settler. The type of reaction in solvent extraction system may be quite complex, and the picture is complicated by the presence of competing and side reactions. The reactors themselves have been generally continuous stirred tanks, and the nature of the mixer-settler makes it unlikely that the pumping mixer can be dispensed with. However, it appears that there should be some definite advantages to a system of stirred reactors in series. The kinetic experiments which are carried out should have the definition of optimum reaction conditions as one of their goals. The data obtained from these experiments must also be applicable to the design of reaction equipment. Reactor selection and design is often a unique problem for each chemical process, and does not lend itself to a systematic general approach. However, the application of chemical and physical principles to mixer design in solvent extraction should result in practical, more efficient plants.

Jan 1, 1979

By Richard H. Jahns

Gem materials, comprising those minerals and closely allied natural substances used for personal adornment, for the fashioning of ornamental objects, or for other decorative purposes, have been valued in human commerce for thousands of years. Amber, jet, natural glasses, and at least 15 mineral species were sought and used by primitive man, and most of the materials in common use today were known well before the time of Christ. Their variety is remarkably great, and the traceable relationships among their respective sources, modes of occurrence, properties, and histories of production, preparation, and valuation are extremely complex. Their uses have been affected by numerous shifts in fashion, and from time to time by superstition, by decrees of church and state, by personal interpretations of religious significance, and by various presumptions concerning medicinal value and influence on human behavior (Ball, 1935, 1950; Kunz, 1913; Pogue, 1915, Whitlock, 1946). Thanks to their durability, portability, and relative scarcity, some gem stones have been employed as media of exchange, and the investment value of the more precious stones has long been recognized and exploited, especially in Asiatic and European countries. Demands for gem materials have stimulated trade among various peoples for centuries, and they also were responsible for much early geographic exploration. During more recent times they have prompted numerous geological studies and a considerable amount of research on the growth and properties of crystals. Apart from decorative uses, some naturally occurring gem materials also are employed directly in numerous fields of industry. Substances that are manufactured for gem or industrial uses are termed synthetic gem materials; most of these correspond in composition and crystal structure to certain minerals found in nature. Imitation materials are those whose use is based upon their resemblance to substances of different composition and greater intrinsic value. Gem stone is a designation commonly restricted to those materials suitable for personal adornment, and the complementary term ornamental stone is applied to the remaining materials not used industrially. This distinction is arbitrary and somewhat inconsistent, owing to numerous geographic differences and historical shifts in end uses. Further, there is a complete gradation between the category of ornamental stones and that of dimension stone. Substances that lose their identity in use are excluded from the gem category; thus a transparent crystal of beryl would not be classified as a gem stone if it were processed as a source of beryllium metal. The adjectives precious and semiprecious have been employed as a means for distinguishing different gem materials on the basis of recognized value. Diamond, emerald, ruby, and sapphire consistently have been regarded as precious stones, and in cut form they commonly are referred to as the noble gems. Opal, pearl, turquoise, and chrysoberyl also have been classed as precious at various times. In recent years, however, it has been increasingly recognized that no satisfactory distinction can be based upon assessed value or any group of specific properties, and now all gem stones normally are referred to as precious. Indeed, the tendency is to extend this term to include many of the so-called ornamental stones, and the designation semi- precious has been essentially discontinued. Unlike most mineral commodities of economic value, gem materials are little altered in processing for end uses. Some stones are used in essentially their natural form, and most are reshaped and polished without significant changes in their fundamental properties. Thus the preparation of gem and ornamental stones is intended chiefly to emphasize or enhance

Jan 1, 1975

By J. Jacob

Diamondiferous linear beaches in Mining Area No. 1 have been the mainstay of Namdeb?s diamond production for more than 80 years. Most of the onshore beaches have been mined out, but in recent years mining has been extended offshore into the surf zone through a process of beach accretion. A total of 61.6 million carats has been produced from the gravel beaches since their discovery in 1928, and Mining Area No. 1 is considered to have great remaining potential from areas currently submerged under water. To date, the surf zone has remained largely unexplored due to the consistently strong winds, currents, and large waves which make access to this area extremely difficult. This paper describes the processes used in developing a practical methodology for exploration of the surf zone in a domain extending approximately 22 km long in a northwest?southeast direction and 0.3 km wide in a perpendicular direction adjacent to the current Mining Area No 1. The vigorous surf zone poses multiple technical challenges in terms of obtaining geological and diamond information. In order to access the area for sampling, a jack-up walking probe drill platform (PDP) with a 5-inch diameter reverse-circulation drill has been developed to carry out exploration drilling in the dynamic surf zone. The hydraulically driven platform has eight legs, each of which is 18 m long. Four of the legs are in fixed positions on the fore and aft sides of the platform. The other four moveable legs are fitted to sliding frames attached to the port and starboard sides of the platform. The sets of fixed and moveable legs can be raised and lowered by hydraulically powered jacking stations. By alternately lifting and lowering the sets of fixed and moveable legs in conjunction with the frames moving back and forth horizontally, a walking action is performed by the PDP. The platform can walk at a speed of 10?15 m/h, depending on weather and footwall conditions. Optimization of sampling for diamondiferous gravel occurrence in Mining Area No.1 was undertaken through creation of a virtual orebody on which different sample configurations were tested. The input data for the construction of a virtual orebody comprises a set of drilling data, collected from recently accreted areas directly adjacent to the 22 km × 0.3 km target domain. The input drilling data covers only 34% of the domain, and for the purpose of this study, a single realization is deemed to be sufficient. The texture obtained from using only the drilling data to construct a simulation did not make geological sense; hence it was necessary to make use of analog data in order to improve the simulation. The first analog data used consists of the gully patterns found in the metasedimentary Precambrian bedrock footwall. Gullies are, in general, gravel filled and it is fair to assume that gully patterns form a subset of the total gravel occurrence. Total gravel occurrence includes marine terraces (governed by sealevel stands) above bedrock peaks, together with gravel within gullies below bedrock peaks. The second analog ?data? introduced is through the use of ?expert interpretation?. The indicator drilling data is interpreted by expert opinion and the 2-dimensional result is hand-sketched, digitized, and then pixelated. The pixelated data set is then used as input for variogram calculation. This study cannot provide a single definite optimization result as the nature of the data does not permit this. The use of different validation approaches (conditioning data, where available; expert interpretation; and gully pattern data), however, can give a very good indication of how to balance sampling effort with de-risking aspects related to geological continuity. Work undertaken by sampling the simulation will give an assessment of the relative probabilities of determining gravel occurrence in the study area. This study showed that a 50 m × 400 m cross-configuration will be a good initial sample spacing for highlighting areas where gravel may be absent, and further infill drilling may be required. The relative efficiency of a 50 m × 400 m cross off-set sampling configuration has been demonstrated using a trumpet curve versus sampling effort when using kriging as the estimation method. Keywords sampling configuration, marine diamonds, orebody simulation.

Jan 1, 2014

By C. Edward Capes

Fine particles in liquid suspension can be agglomerated by a number of mechanisms. Well-known methods include the addition of electrolyte to reduce the zeta potential and allow mutual adhesion arid the use of polymeric flocculants to bridge between the particles. A more recent technique, "spherical Agglomeration", is the subject of this paper. The process involves the addition of a second liquid which is immiscible with the suspending liquid and preferentially wets the particles to cause particle adhesion by capillary liquid bridges. Progress in the application of spherical agglomeration to a number of distinct technological fields is reviewed in this paper. The areas of interest include the formation of dense, highly spherical agglomerates, the separation of solids from suspension and the fractionation of complex, multi-component solids mixtures, such as ores. Some of the more interesting recent applications in the energy and environmental fields, such as the beneficiation of' coal and tar sands, are highlighted.

Jan 1, 1977

By Glastonbury J. R

The kinetics of the direct chlorination of, zircon in the presence of carbon was studied at temperatures between 9000C and 12000 C. From the experimental data it is prop- osed that the most likely mechanism for metal oxide (MeO2) chlorination is as follows: At I Surfaceon zMeO2+ZMeCl - MeOC12 (1) At Carbon MeOC12+C+Cl MeC14+CO (2) Surface It.is envisaged that this type of mechan- ism would occur for both the zirconium and, silicon. constituents of the ore. In the above mechanism; the surface re- actions appear to be fast and not rate controll- ing. In a carbon surface deficient bed the diff- usion of oxychloride intermediate through the boundary layer to the carbon surface becomes the rate controlling step. In a zircon surface deficient bed the diffusion of oxychloride away from the zircon surface controls the reaction. This postulated mechanism can be used to ex-, plain the observed experimental effects.

Jan 1, 1973

By D. A. Norrgran, J. A. Wernham

Introduction In view of the continuing depletion of natural resources, requirements for energy conservation, plant optimization and hazardous waste management, and environmental consciousness, recycling and secondary recovery of materials are being developed with increasing interest Many secondary recovery processes are being developed that apply mineral processing technology. Gravity separation, magnetic separation and flotation have all emerged as explicit methods for recovering residual values from various process streams and hazardous constituents from waste streams. Recently, a technique for concentrating metallics has been successfully reintroduced. The concept of the alternating magnetic field eddy-current separator was developed over a century ago using rudimentary electromagnets (Patent 400317 issued to Thomas Edison on March 26, 1889). Widespread acceptance was, however, hindered by high costs, marginal results and poor economic incentives for secondary recovery. With the recent increased interest in secondary recovery and the development of high-energy rare earth permanent magnets, the eddy-current separator has now gained prominent acceptance. The separation forces imparted by an eddy current separator are the function of the magnetic field intensity and the alternating frequency of the magnetic field. The evolution of permanent magnets has provided a cost effective alternative for the generation of high-intensity magnetic fields. High-energy rare earth permanent magnets have substantially reduced the capital and operating costs over the electromagnetic circuits employed in antecedent eddy-current separators. Specifically, in recent years, the strength of permanent magnets has increased several fold with neodymium-boron-iron rare earth magnets now providing an energy product of 35 million gauss-oersted. Figure 1 shows the evolution in the strength of permanent magnets. The development of these rare earth magnets has led to the design of circuits possessing a magnetic force an order of magnitude greater than that of conventional permanent magnetic circuits. The eddy-current separator has been successfully applied in several metal sorting and recovery operations. Most common is the sorting of metal from shredded automobile scrap and municipal waste. With the advent of high-frequency, high-intensity magnetic fields, the separator has advanced to the point where it has direct application in the beneficiation of fine sized metals. Relatively fine sized (-1/4 in.) metal bearing slags and spent foundry casting sands as well as precious metal hearing electronic scrap demonstrate excellent metallurgical response to the eddy-current separator, and applications have progressed to finer materials and more selective separations. Theory Electrical currents are induced in all conductors when exposed to an alternating magnetic field. The induced current generates a magnetic field in the conductor that opposes that of the alternating magnetic field. Figure 2, is a schematic illustration of generated eddy currents. In this particular example, the alternating magnetic field is produced by a series of permanent magnets mounted on the circumference of a rotor. The permanent magnets have alternating polarity. As the rotor revolves, an alternating magnetic field is produced, and the rate of revolution determines the frequency of the alternating magnetic field. When a conductor, such as a metallic disc in the illustration, is placed in the alternating magnetic field, a closed loop current flow occurs. The current loop in the conductor produces a magnetic field that is a mirror image of the alternating magnetic field. At any point in time, the induced magnetic field in the conductor directly opposes the alternating magnetic field. This opposition of magnetic fields produces an instantaneous repulsion in the conductor. The conductor is consequently repelled from the rotor. The alternating magnetic field has no effect on nonmetallic materials as they pass through the magnetic field and discharge the rotor in a natural trajectory. [ ]

Jan 1, 1992

By Richard H. Jahns

Gem materials, comprising those minerals and closely allied natural substances used for personal adornment, for the fashioning of ornamental objects, or for other decorative purposes, have been valued in human commerce for thousands of years. Amber, jet, natural glasses, and at least 15 mineral species were sought and used by primitive man, and most of the materials in common use today were known well before the time of Christ. Their variety is remarkably great, and the traceable relationships among their respective sources, modes of occurrence, properties, and histories of production, preparation, and valuation are extremely complex. Their uses have been affected by numerous shifts in fashion, and from time to time by superstition, by decrees of church and state, by personal interpretations of religious significance, and by various presumptions concerning medicinal value and influence on human behavior (Ball, 1935, 1950; Kunz, 1913; Pogue, 1915; Whitlock, 1946). Thanks to their durability, portability, and relative scarcity, some gem stones have been employed as media of exchange, and the investment value of the more precious stones has long been recognized and exploited, especially in Asiatic and European countries. Demands for gem materials have stimulated trade among various peoples for centuries, and they also were responsible for much early geographic exploration. During more recent times they have prompted numerous geological studies and a considerable amount of research on the growth and properties of crystals. Apart from decorative uses, some naturally occurring gem materials also are employed directly in numerous fields of industry. Substances that are manufactured for gem or industrial uses are termed synthetic gem materials; most of these correspond in composition and crystal structure to certain minerals found in nature. Imitation materials are those whose use is based upon their resemblance to substances of different composition and greater intrinsic value. Gem stone is a designation commonly restricted to those materials suitable for personal adornment, and the complementary term ornamental stone is applied to the remaining materials not used industrially. This distinction is arbitrary and somewhat inconsistent, owing to numerous geographic differences and historical shifts in end uses. Further, there is a complete gradation between the category of ornamental stones and that of dimension stone. Substances that lose their identity in use are excluded from the gem category; thus a transparent crystal of beryl would not be classified as a gem stone if it were processed as a source of beryllium metal. The adjectives precious and semiprecious have been employed as a means for distinguishing different gem materials on the basis of recognized value. Diamond, emerald, ruby, and sapphire consistently have been regarded as precious stones, and in cut form they commonly are referred to as the noble gems. Opal, pearl, turquoise, and chrysoberyl also have been classed as precious at various times. In recent years, however, it has been increasingly recognized that no satisfactory distinction can be based upon assessed value or any group of specific properties, and now all gem stones normally are referred to as precious. Indeed, the tendency is to extend this term to include many of the so-called ornamental stones, and the designation semiprecious has been essentially discontinued. Unlike most mineral commodities of economic value, gem materials are little altered in processing for end uses. Some stones are used in essentially their natural form, and most are reshaped and polished without significant changes in their fundamental properties. Thus the preparation of gem and ornamental stones is intended chiefly to emphasize or enhance

Jan 1, 1983

The notion of wayfinding, as conceptualized by planners, geographers, and psychologists, denotes the ability of an individual to move from one point to another through physical space. In order to achieve this movement, a person relies on a cognitive map of spatial representations [Passini 1984]. Which features of this cognitive mapping will be stressed depend, in part, on the researcher's perspective. A planner, for instance, would tend to emphasize the effect of physical structures on mobility. A psychologist, on the other hand, might focus on individual differences in how human minds encompass and represent physical space [Evans et al. 1984]. There is yet another dimension to wayfinding that needs consideration, and it rests upon the idea that reality, as experienced by human beings, is mediated: "[People] have preselected and preinterpreted this world by a series of commonsense constructs ... which help them find their bearings in their natural and socio-cultural environment and to come to terms with it" [Schutz 1967]. These "common sense constructs" are arrived at socially and constitute the agreed-upon schemas that guide people's everyday activities. According to this principle, cognition is governed by some nonlogical factors that reflect not only individual procedures but collective ones as well. These group strategies, which are shaped by shared rules and values, influence "the information gathered, the ways it is processed, the inferences that are drawn, the options that are being considered, and those that are finally chosen" [Etzioni 1992]. From this perspective, cognitive maps, rather than being individual-centered templates of environmental images [Rovine and Weisman 1989] or representations of spatial relationships [Evans 1980], are partially group-centered schematic processes. As such, they are subject to reinterpretation, revision, and outside intervention [Kaplan and Kaplan 1982]. As intermediaries between the environment and behavior, cognitive maps serve as bases for decision-making. Traditionally, it has been assumed that good maps facilitate correct decisions, which in turn leads to optimal performance during wayfinding [Hunt 1984]. Given the argument that there is a social (non¬cognitive) facet to cognitive mapping, however, this image of a cognitive map as some sort of static reference construct that motivates individual action is too narrow and mechanistic. If cognition involves less a knowledge of the environ¬ment than it does the process of "giving it meaning through imposing an order on it" [Rapoport 1976], then wayfinding behavior is not j ust a function of setting and individual differences, but is also a function of one's "normative-affective" structure [Etzioni 1992]. Rapoport [1976] used such an assumption as the base for a set of hypotheses about the connection between "external demands" and "organismic factors." One significant assertion deriving from Rapoport's ideas is that environmental

Jan 1, 2000

By Linn Bradley

R. J. WYSOR, So. Bethlehem, Pa. (communication to the Secretary*). At our plant (Bethlehem Steel Co.), we have had several Bradshaw burners under course of construction and erection for some time, but up to the present we have not had opportunity to put them in service. I regret that I can not take part in the discussion with some actual results from these, burners. Mr. Huessener properly emphasizes the importance of obtaining the highest combustion temperature practicable in boiler practice, which demands a near approach to perfect combustion conditions. The ideal burner is the one which, while meeting the various mechanical, requirements, fulfills the above condition under a wide range of gas pressure. The question as to the relative value of hot raw gas and cold washed gas for boiler use is a very interesting one. I think that in the past the importance of low temperature of washed gas sometimes has been over-emphasized. Mr. Huessener has pointed out that so far as temperature is concerned, no advantage accrues in washing gas below 100° F. In

Jan 3, 1917

By Gilbert Thiessen

THE use of a pneumatic process for removing fine material (usually less than 48-mesh) is increasing in, the preparation of stoker-size coal. The fine material, produced as a byproduct, is known as dedusting-plant dust. Since fusain is the most friable ingredient in bituminous coal (it may readily be rubbed to an impalpable powder with the fingers), it tends to accumulate in this byproduct. While studying the properties of cokes produced by blending Illinois coals with other materials, considerable quantities of fusain were required. Dedusting-plant dust suggested itself as a-convenient supply. It became necessary, therefore, to determine how much fusain was contained in a measured sample of dust, how the fusain was distributed with respect to size and specific gravity in the sample, and whether or not it would be feasible or desirable further to concentrate or to recover the fusain from, the dust before using it in the blends to be coked. The results obtained indicate the possibilities of production of a high-fusain material.

Jan 1, 1936