Search Documents

Provide optimum visibility of mining operations while maintaining protection and comfort for machine operators. Approach A cab with hydraulically powered variable-height control was developed and used on a loading machine in underground operations. How It Works The cab is attached to the vehicle on a horizontal trunnion located near the forward end of the cab. A hydraulic cylinder, controlled by the operator from inside the cab, pivots the cab about the trunnion providing variations of up to 16 inches in elevation. The nominal tramming position of the cab is with its underside 6 inches above the mine bottom. From this position the cab can be pivoted up, or down, so that its back end is elevated 10 inches, or lowered to the floor. (See Figure 1.) The cab encloses the operator for protection against both overhead and lateral obstructions, and it raises or lowers, allowing the operator to select the most advantageous cab height. The cab is angled inboard 30 degrees to the machine line of direction. The operator's seat swivels to allow view of the conveyor during loading. All controls are located within the cab and move up and down with it.

Jan 1, 1978

H. G. Haemers (Ghent University, Belgium)—The authors claimed "the results of their work indicate that the metals can be arranged in a sulfation series similar in its application for selective sulfation tot the electromotive series for displacement of metals from solution". The series as stated in decreasing order for tendency of SO3 give up, is the same as that stated by free energy diagrams. Indeed, the degree of stability of a sulfate is measured by the free energy of sulfate formation out of the corresponding metal oxide and SO3. The more negative the value of the free energy (-DG) the greater the stability of the sulfate. As a second consequence this statement results in a relative aptitude for capture of SO3 by each metal oxide when brought in contact with the sulfate of other metals. Let M1 and M1 be the two metals, and — DG1 and — DG2 their free energy values at temperature T. Both sulfates are stable at temperature T if - DG1 < O and — DG2 < O. In case where — DG1 < — DG2 the stability of M1SO4 is greater than that of M2SO4, and when M1O (oxide of

Jan 1, 1958

By Eugene F. Casey, William H. Hansmire, J. Ghaboussi, Randall L. Lentell, Harvey W. Parker

INTRODUCTION Construction of a major intercepting sewer in Brooklyn, New York involved tunneling in soil over several subway lines. In two instances the clearance between the subway and sewer was sufficiently close that concern was raised about the influence of the new construction. Prior to each critical crossing, analytical studies were performed which characterized the tunneling influence. It was demonstrated that with adjustments in construction procedures the crossings could be made without affecting the integrity of the subway linings. A comprehensive program of instrumentation and full-time monitoring was undertaken to ensure that any unforeseen adverse developments during crossing would be recognized. The successful crossings were subsequently made with minimal influence. Reported herein are the special construction conditions for the two crossings, the analytical simulation of behavior, and the results of monitoring on the subway linings. SEWER TUNNEL CONSTRUCTION AND EXISTING SUBWAYS The Red Hook Intercepting Sewer is a 2600 m (8600 ft) long tunnel which is part of a major water pollution control project in New York City. For clarity of nomenclature, the sewer is termed a &apos;tunnel&apos; while the rapid transit structures are termed &apos;subways&apos;. For routine construction, the tunnel was mined by hand with a 3.2 m (10 ft-5 in.)

Jan 1, 1981

By J. L. Stokes, L. J. Demer

It has recently been shown&apos; that epitaxial films of silicon carbide deposited on silicon single crystals possess desirable properties for semiconductor applications. There is one apparent disadvantage to such a system, however; since epitaxial deposition is a high-temperature process, it can result in plastic deformation of the silicon substrate. The accompanying Berg-Barrett X-ray diffraction photographs reveal plastic deformation in two silicon semiconductor crystals which occurred when the crystals were coated with an epitaxial layer of silicon carbide at 1150°C. Due to differences in thermal expansion between the silicon substrate and the epitaxial silicon carbide, the silicon was subjected to stresses while still in the plastic temperature range. Both crystals shown were 0.7 in. in diam and 0.0055 in. thick. The crystals were sliced from a larger crystal so that their polar axes were parallel to the [ill] direction. After cutting, the crystals were polished with diamond paste, and etched in HC1 vapor to remove surface damage re- sulting from the cutting and polishing operations. This provided clean, damage-free surfaces on which to deposit the silicon carbide. Figs. l(a) and l(b) are reflection and transmission photographs, respectively, of the same crystal. A smaller portion of the crystal is shown in the transmission geometry, because a vertical slit was

Jan 1, 1965

In recent years rehabilitation of mine sites has become a principal focus of mining legislation in Victoria. In previous eras, managed rehabilitation commenced, if at all, towards the end of mining operations. Planning for rehabilitation works now commences before an exploration licence is granted.The paper gives a brief overview of the requirements for rehabilitation under the Mineral Resources Development Act 1990, Extractive Industries Act 1966, and related environmental planning legislation including rehabilitation bonds and enforcement provisions.A brief review of the current taxation provisions is also included.

Jan 1, 1992

By D. K. Sitler

Continuing advancements in manufactured diamond materials as used in rock cutting tools have created a new generation of high production tools for mining. This paper reviews the three major manufactured diamond product types available in the mining industry as supplied by General Electric Co., Specialty Materials Dept., and examines the ways these materials are used. As an integral part of this examination, the economic impact of manufactured diamond tools is evaluuted. Time and again, one will find that the premium price for these tools is economically justified when compared to traditional tools.

Jan 1, 1988

By L. J. Demer, W. W. Walker

AMONG several variables of the indentation hardness test is the effect of loading time on the measured hardness of a material. The most generally recommended duration of loading is 10sec.1-3 Although this short loading duration is undoubtedly satisfactory for harder metals, it is questionable that it is sufficient for very soft metals,4 or for certain plastics.5 The effect of duration of loading on the measured hardness of ionic crystals is largely unknown, although Onitsche and Mitsches found that the indentor (under a very low load) had not yet reached equilibrium after 60 sec in a variety of ionic crystals. To extend further the data of Onitsche and Mitsche, a systematic study was made of the effect of duration of loading for longer periods, up to 50,000 sec, on the 136 deg Dph of synthetic lithium fluoride. For comparison, less extensive tests were made on synthetic magnesium oxide and copper single crystals. The general procedure used was to indent a cleaved and polished (100) face of a lithium fluoride crystal using a Leitz Durimet microhardness tester. In certain cases, the indentor was so oriented as to align the diagonals of the 136 deg diamond pyramid indentation parallel to a (100) edge. In other cases the diagonal of the indentation was aligned at 45 deg to a (100) edge of the crystal. After indenting, the surface tested was etched in the acid etchant recommended by Gilman and Johnston.&apos; This revealed the position of dislocation lines which intersected the surface tested. At these points of emergence were formed the usual sharp, pyramidal etch pits as shown in Fig. 1. The specific procedure used in studying duration of loading was as follows. The surface of the crystal was indented, and the load was left on the indentor for a predetermined time. This duration of loading was varied systematically from 1 to 50,000 sec. After the desired amount of time had elapsed, the indentor was removed from the crystal and the size of the resulting indentation was determined using a micrometer eyepiece. The surface was then etched to reveal the dislocation etch pit pattern around the indentation. Procedures used for lithium fluoride, magnesium oxide, and copper were similar. Preliminary studies revealed that, although an indentation was enlarged by increasing loading time, no corresponding changes occurred in the surface etch pit pattern. Since no evidence of dislocation movement was observed on the surface, it was assumed that the plastic deformation indicated by the indentor sinking into the surface was a result of dislocation movement inside the crystal. This movement was studied bf making a series of surface indentations in a crystal corresponding to various lengths of time, cleaving the crystal vertically through the indentations, etching the freshly

Jan 1, 1964

FOR twelve successive years Canada&apos;s mineral production has shown a steady increase, rising from a value of $0.5 billion in 1945 to $2.06 billion in 1956, and the outlook for the future is one of continued growth. A great deal of credit for this growth must go to Canada&apos;s tax policies, which recognize that mines are difficult and costly to find, and that once found, they are a wasting asset. These tax policies take form under the Income Tax Act, which provides a tax- free period of three years on initial production for new mines and, after that period is over, allows all proper expenses of operation to be deducted from mine revenue. These allowable expenses include write-off of plant and pre-production development expenditures. From the resulting profit figure after this procedure, a further deduction of one-third is allowed for depletion before net taxable income is arrived at. Tax rates of 20 pct on the first $20,000 and 47 pct on the excess are then applicable to the net taxable income.

Jan 12, 1957

By Fred C., Bond

IN CYANIDE milling, little attention has been paid to the effect of the viscosity of the mill solution on the extraction speed. The viscosity of the solution varies with the amount of dissolved salts present as impurities. These salts build up to a maximum depending on the character of the ore, the grade of cyanide used, the lime and salts added, and the impurities originally in the water. The viscosity will change from month to month and week to week as these factors vary; and that this variation affects the extraction is unquestioned, although methods for calculating it are lacking. The character of the ore is probably the most important of the four factors, as the amount of minerals present that are soluble in cyanide solution will vary constantly, and each variation affects the viscosity of the mill solution. When the cyanide consumption increases as the character of the ore changes, the viscosity of the solution will increase and the extraction will decrease, for the cyanide consumption is usually a measure of the impurities dissolved from the ore. In other words, as the difference between the total and free cyanide increases the extraction will decrease, other factors remaining constant.

Jan 1, 1926

By C. J. Bise, D. A. Poukhovski

Hazard recognition and prevention of accidents are two components of the 30 CFR 48 training requirements, which are mandated for new miners and newly employed experienced miners. These components are also part of the annual refresher training course required of all miners. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine and shall include a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition presents a particular challenge to safety-training specialists, because they are often limited in their ability to adequately gauge the level of awareness of the individual prior to training. Further, they must also assure that the training is relevant and presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard-recognition topics, because it can be used in pretraining and posttraining modes for assessment of training effectiveness, in addition to its use as a presentation tool. This article presents a recent approach, developed at The Pennsylvania State University, that applies the technology for the assessment and instruction of accident prevention through hazard recognition. The application is prepared for surface coal mines.

Jan 1, 1999

By G Dean Barrett

Just one year ago at the 1986 Annual Meeting of the Society of Explosives Engineers, Dr. Calvin J. Konya presented a paper entitled "Presplitting Granite Using Pyrodex, A Propellant.'' Since that time more evidence has been developed to support the concept that "...gas energy can be the principal splitting force and that the stress wave or shock wave is not necessary to cause the presplitting action to occur." Work done in Vermont and Georgia is presented, and the ability to split granite without causing radial cracking of the bore holes is demonstrated.

Jan 1, 1987

By R. P. Moran, B. C. Lewis

The objective of this article is to discuss the fundamentals for determining the value of a limestone reserve or operation. The general step-by-step procedure, while prudent, is subject to the various site-specific issues that influence the valuation calculation. The most common methods for determining fair market value of mining lands are: comparable sales, operational analysis, and royalty analysis. An overview of typical eastern limestone mines (both quarries and underground) is presented. Specifically, properties in West Virginia and Alabama are reviewed and the sample methodologies and valuation calculations are presented.

Jan 1, 1991

By J. A. Elias, R. H. Heyer, J. H. Smith

Plastic anisotropy determined by the ratio of width strain to thickness strain in tensile specimens of low-carbon steels is strongly related to crystallographic preferred orientation. Using(222) Pole figures, a method was developed which permits rapid Predictions of plastic anisotropy for any crystallographic texture or orientation. The method is applied to low-carbon steel sheets in which four different crystallographic orientations were produced by variations in cold rolling and annealing treatments. AnISOTROPIC behavior of metal sheets during plastic deformation has long been evident. A familiar example is earing in cup type draws. During tension testing of sheet specimens, anisotropy results in a difference in width strain as compared with thickness strain. Carpenter and Elam1 observed this phenomenon in single crystals of aluminum for both sheet and rod samples. Lankford, Snyder, and Bauscher2 made tension tests on sheet samples of aluminum-killed low-carbon steel to determine the ratio of the width-to-thickness strains, and showed that this ratio was related to drawing performance. Burns and Heyer3 calculated theoretical ratios of width strain to thickness strain for two specific orientations of the bee system, using <111> as the operative slip direction. These calculated values were in fairly good agreement with the ratios determined by tension tests of low-carbon steel sheets in which these preferred orientations existed. The high degree of plastic anisotropy of silicon steel sheets could also be predicted from their crystallographic structure by these calculations. The present study has been made to show that the anisotropy observed in plastic tensile straining is strongly orientation dependent and can be adequately predicted for many orientations and textures. PLASTIC STRAIN RATIO R In the region of uniform elongation of a tension test specimen the plastic deformation may proceed at different rates in the width and thickness directions. Such anisotropy has been described in the past by the plastic strain ratioR:

Jan 1, 1962

By Graham W. Marks, RALPH MILLS, FRANK COSSEY

To determine the focal length of lenses or the performance of lens systems before mounting them permanently , it is desirable to have a device in which one or more lenses can be mounted easily and their positions relative to a light source and screen changed readily . We have designed and constructed such an optical bench and lens holder . The bench is similar to that of Houstoun5/ but has been modified , whereas the lens holder is , we believe , a new design .

Jan 1, 1948

By J. F. Nicholas

THE angles between the crystallographic planes in cubic metals were originally given by Bozorth and have been republished many times. Recently, Salkovitz2 tabulated the angles for the hexagonal metals (magnesium, zinc, and cadmium). he most commonly used metal which does not fail into either of these groups is tin, which has a tetragonal structure with an axial ratio of c/a = 0.54558 (99.99 pct purity, 25°C).² ccordingly, Table I has been prepared giving the possible values for the angle, 4, between planes of the types {HKL) and {hkl). The formula used was: Hh + Kk + LI — cos? = —--------------—-----------— A [(H2 + K2 + L2-a2c2(h2 + k2 + r;)] All angles are given correct to the nearest minute as this is sufficient for all practical purposes. Every angle depends in a different way on variations in the value of c/a, but even in the worst cases a variation of about 0.0003 in this ratio is needed to vary an angle by l&apos;, which corresponds to a temperature change of 20 °C or can be caused by impurities.

Jan 1, 1952

By H. D. Hoskold

This paper is presented in fulfillment of the promise made in my paper, " Remarks upon Surveying-Instruments,"" etc., and much of the material which would constitute an appropriate introductioil here is omitted, because it has been already published by the Institute, in connection with my own contributions- or those of Mr. Scott and others, in vols. xxviii. to xxxi. of the Transactions, and in the special Institute volume on Mine-Surveying Instruments. In these preceding publications will be found, for instance, descriptions of the writer&apos;s " miner&apos;s transit-theodolite" of 1863,† and his later " angleometer,"‡ both of which were steps of the progress in engineering instruments and methods which originated in the work of Bourns, before 1842, on the " BoxTunnel " of the Great Western railway in England, in which he had to make connections by direct telescopic sights down the shafts. About 1870 the writer devised a practical and much superior plan, and made detailed drawings for an instrument to meet all the conditions he had proposed prior to that year. The detailed plans were communicated to a celebrated optical firm in London; but, owing to their loss (in Paris or Germany, it is believed) and to other reasons, the matter was, for the time, allowed to lapse. Following upon Bourns&apos;s idea, my friend, the late Mr. Beansland, introduced, in 1856, a new system and a portable astronomical instrument.§ Such instruments, however, were neither common nor convenient, and did not come into general use among engineers.

Jan 1, 1902

By Adranyl W. W

Sub-level caving with bottom ore drawing has gained wide acceptance in rich, soft, low magnetic iron ores because it provides moderate ore dilution and ore losses. The main problem here is the high rock pressure exerted on sub-level drives situated in the sub-level sill pillars. To reduce this effect, the ore block is divided into panels. This paper illustraes the method of determining the maximum panel width providing low maintenance cost of sub-level drives.

Jan 1, 1995

By Anthony Iannacchione, Christopher Mark

Residents of Maxwell Hill, a suburb of Beckley, West Virginia, reported from January until March of 1988 a series of earth tremors. The tremors rattled dishes, and the noises associated with tremors were sometimes loud enough to wake people at night. These events were puzzling because Beckley is in an area of low seismic activity. Maxwell Hill is located above abandoned coal mines, though no direct subsidence damage to surface structures has been documented. A research program was initiated to determine whether subsurface ground movements associated with the abandoned mines could be responsible for the seismic activity experienced at the surface. A hypothesis is proposed which states that seismic disturbances can be caused by abandoned mine failure when two conditions are met. First, some instability must exist at the mine level. The most likely cause of instability is the failure of pillars of coal that were left for support at the time of mining. Second, subsurface movements can result in significant seismic activity only when the rock above the mine contains at least one very strong and brittle layer that is prone to fail violently through rupture or fault slip movement. Analysis of the data indicates that both hypothesized conditions for mine-related seismicity appear to have been satisfied in the case of Maxwell Hill. It has therefore been concluded that the earth tremors experienced by Maxwell Hill residents probably are related to the abandoned mines. Analysis of the potential magnitude of these events indicates that they are unlikely to cause significant surface danlage. The probability that future events will disturb the residence of Maxwell Hill should be quite low based on the identified mechanism.

By Peter de Kort

Tunnels in urban areas generally require deep excavations in soils under the groundwater table. In The Netherlands uplift loads are generally taken by piles installed into dense sand layers, which are hard to penetrate. To avoid nuisance and damage to the environment, piles often need to be installed using vibration free methods, which also have the advantage of low noise levels during installation. Drilling piles and obtaining a high uplift resistance is a contradiction in itself. Franki has adopted several installation methods based on the injection of grout during drilling and/or post grouting to overcome the difficulty of hard layers. This report presents two projects, situated in Rotterdam and Sneek, where vertical tension piles in floors, subject to high uplift loads, have been used. It also explores a project in Zeebrugge (Belgium), where tension piles are installed at an inclination of 1:1 to anchor a diaphragm wall for a quay construction. Test results presented in this report show, that vibration free and soil displacing piles can be installed in very dense sand layers and that a high uplift resistance can be achieved. It is also shown, that a variety of installation methods is available, even in limited space.

Jan 1, 2008

By Jyotirmoy Sarma

The surface-active agent, like sodium humate, in the present systems produces a very stable suspension. Saline water up to 15% is used as a flocculating agent for recovery of water from the dispersed phase containing 1% solid. The recovered water in the presence of humate at different concentrations (0.05-0.2%) and at pH 8 also produces a stable dispersed phase of iron ore fines and tailings. The beneficiation techniques adopted in the present systems can increase ~ 2-3% iron value in the concentrate of iron ore fine, however, for tailings the increase in iron value is not observed. Keywords: beneficiation, flocculation, iron ore fines, tailings, saline water, surface-active agent

Sep 1, 2012