Search Documents

By G. T. Lineberry, R. S. Mateer

Often only after years of "technical dormancy" do errors in published literature become apparent and meaningful. To prevent duplication of effort for future generations, the following corrections are offered. These errors were discovered during a recent study in which a computer program for mine hoist rope selection was developed (Lineberry and Mateer, 1988). In order of increasing gravity: Captions for Figs. 3 and 4 are transposed. Purported to be a more accurate method of rope selection than the process of successive approximation, the direct method assumes linearity between a given rope's minimum breaking strength, T, and unit rope weight, WV. Because of the sensitive location of the constant, K, in equation (8) for breaking strength, the significance of this nonlinearity is magnified. For a typical 6 x 37 class fiber core wire rope (Wire Rope Corp. of America, 1985), K actually varies from 43,650 to 52,190, depending upon rope diameter. Although the direct solution permits a rapid selection of hoist rope, an indirect (iterative) solution procedure is favored because of its improved accuracy and ease of computerization. Equation (8) for minimum breaking strength is in error. It should read:

Jan 1, 1990

Prof. Frank H. Probert, dean of the College of Mining of the University of California, visited the mining areas in the devastated regions as a member of the Bureau of Mines committee, which is studying the problems presented in the rehabilitation of mines there. He says that the absolute destruction of the coal mines in the Pas de Calais section makes it-necessary to use either the Westphalia or the Saar valley coal. The Saar mines, however, produce a poor quality of coking coal: therefore, it will not be possible to operate blast furnaces very efficiently unless provision is made for the introduction of better coal. He believes

Jan 6, 1919

By R. O. Y. Breese

Perlite is a hydrated acid volcanic glass that has been derived from the alteration of obsidians through incorporation of water into the silica structure. It is distinguished from other members of the water-bearing natural glass family by total water content, characteristic fracture and luster. The distribution of major occurrences worldwide is associated with silicic Tertiary through early-mid Quaternary volcanics related to plate movement. The No Agua dome and flow complex is one of the most highly studied perlite occurrences in the world. It clearly exhibits lithologic and textural zonations that reflect simple cooling history. Similar features are commonly observed within other perlitized, extrusive glass selvages. This paper briefly discusses current thought regarding geologic occurrence, the hydration process and the modes of origin with special emphasis on No Agua.

Jan 1, 1985

By Ting Chinsu

Diaphragm wall with tie-back cable is widely used for deep excavation, especially in the area with high density of buildings. This paper presents the measured earth pressure distribution on diaphragm wall during excavation. The earth pressure cells used in field were successfully installed in deep slurry trench by a new type of simplified manipulator. The sizes of the deep excavation are 26m X 36m on plane and 9m in depth. The construction site is located between two multistorey buildings at the main business section of Beijing city. In this paper the field measurements of earth pressure distribution and the analyses based on the comparison between calculation and measurement are very valuable to improve the current calculation method for diaphragm wall design.

Jan 1, 1991

By R. V. Ramani, V. T. Burgos, J. A. McClay

Introduction The Cost program was developed to provide the planning engineer with a tool to evaluate the cost implications of the technical mine design decisions. Direct costing methods are employed, where feasible, to provide greater detail and accuracy in the primary cost centers. Options have been provided in the cost computation, economic analysis, and output data subsystems to increase the flexibility of the system. Computer Program The program is written in Fortran IV for use in the IBM System 360/370 computers. i. Main - The main routine reads and stores input data from three sources, user input, Cost Data Library, and data transfer from the Master Design Simulator. Data is trans¬ferred to the appropriate subroutines, as they are called, by means of labeled common blocks. ii. Subroutine CSTCOM - is a data modification routine which computes the peripheral charges related to labor and supervisory costs. iii. Subroutine MANPWR - interrogates section data to determine the total labor and supervisory costs for each cost center. iv. Subroutine CAPCST - computes the total capital investment for each cost center, including the economic life and salvage value of each element. Capital costs are determined by user selection of quantities and models of equipment. Equipment costs are stored in the Cost Data Library for retriev-

Jan 1, 1975

By M. S. Moats, C. M. Campbell

Samples of a high impurity (90.05 wt. % Cu, 4076 ppm Pb, 1939 ppm As and 635 ppm Bi) commercial copper anode were characterized and then electrorefined in a laboratory scale cell. Anode inclusions were examined using backscatter mode scanning electron microscopy and energy dispersive spectroscopy. Hundreds of inclusions were measured for size, morphology and composition. Commonly found inclusions were copper oxide (Cu2O), complex oxides (Cu-Pb-Bi-As-O) and copper selenides/tellurides. The weight percent of lead and arsenic increased with increasing inclusion size up to 4- 5 microns. During electrorefining, starter sheet ductility was negatively impacted by thiourea addition. The importance of arsenic (V) concentration on the electrolyte concentration of bismuth was observed. INTRODUCTION Copper electrorefining is a commercial process used to produce the majority of the world’s refined copper. During this process, impure copper anodes are dissolved electrolytically, and high purity copper is deposited on cathodes. As the anodes dissolve, the impurities either accumulate in the electrolyte or report to solids that form on anodes surfaces or at the bottom of the refining cell. These solids are called slimes. Slimes contain precious metals and are collected for further processing. Slimes are also an important outlet for problem impurities such as lead, antimony and bismuth. The electrorefining process is operated in such a way to encourage the deportment of these elements to the slimes. Impurities in copper anodes have been studied extensively by Chen and Dutrizac (1990, 1993 and 2005). The most common impurities found in modern copper anodes include: Ag, As, Au, Bi, Fe, Ni, O, Pb, Sb, Se, Sn and Te. Impure copper anodes are produced by pyrometallurgical methods and have purities ranging from 97.7–99.7% Cu (Moats et al., 2019). The composition ranges of commercial copper anodes from the 2019 worldwide tankhouse survey are given in Table 1. The concentrations of anode impurities vary widely dependent on the source material and prior processing steps. Based on the work of Chen and Dutrizac, both gold and silver are predominantly found in solid solution within the copper grains while a minor amount of Ag can be found in Cu2(Se/Te) inclusions. Nickel is entirely soluble within the copper grains up to anode compositions of 2500–3000 ppm Ni; above which NiO and kupferglimmer phases are formed (Chen & Dutrizac, 1990). As, Bi, Pb and Sb are found in solid solution within copper and within oxide inclusions typically found along grain boundaries. Oxides are formed due to the presence of 0.13-0.18 wt. % O (Chen & Dutrizac, 1990). This is because during solidification of the cast anodes, impurities are enriched in the liquid phase as the copper grains nucleate and grow. The inclusions form from the last liquid to freeze, which is typically along grain boundaries (Wenzl & Filzwieser, 2007; Wenzl, Filzwieser, Mori & Pesl, 2008).

Jan 1, 2019

By Yueyue Ding, Yuanhui Li, Zhengrong Li, Pengfei Yu, Kunmeng Li, Zhipeng Xiong

The stress evolution and failure characteristics of overburden were studied during multi-stope mining for a gently inclined thin orebody. Firstly, an indoor physical experiment was conducted on the excavation of a multi-stope mine with an orebody dip angle of 20°. The results show that the vertical stress concentration area gradually shifts to deep-buried rock mass with the mining from shallow to deep buried stopes, resulting in shear failure originating from high stress. On the contrary, the pressure relief zone presents an asymmetric distribution characteristic that is biased towards the upper part of the goaf, resulting in large subsidence and tensile failure of the stope #1 and #2 roofs. Secondly, the numerical simulation model under the same geological condition was established to measure the roof deformation at different stages of mining. The numerical simulation results are in good agreement with the physical test results; the roof displacement is largest in stope #2, second-largest in stope #1, and smallest in stope #3. Finally, the evolution of deviator stress concentration, displacement field and potential failure zone of overburden under different orebody dip angles were studied. As the dip angle of the orebody increase, the deep-buried stope roof changes from deviator stress release to deviator stress concentration in different stages of mining, and shear failure is most likely to be induced when the orebody dip angle is 30°. Meanwhile, the closure displacement of the stope roof decreases gradually, while the tangential displacement increases, so the anti-sliding ability of the support bodies in the stope should be improved. The potential tensile failure zone gradually shifts from the center of the goaf to the upper part, and the deep-buried stope roof evolves from tensile failure to shear failure. Results of this research expected to provide guiding significance for stope support design to control roof deformation and failure, to ensure the safety of the stope.

Mar 2, 2023

By Frank E. Chase, John L. Ellenberger, Christopher Mark

The nature of competition in the coal market tends to deplete the most favorable coal reserves first, and forces subsequent development of mines in more extreme ground conditions such as those associated with multiple-seam mining. In fact, 70% of the United States coal reserves are in multiple-seam situations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop mine design algorithms that will result in safer multiple seam mines. This paper presents an overview of multiple seam issues in the central Appalachian coalfields. To date, more than 50 case histories have been analyzed from 20 operating mines in Eastern KY, Western VA, and Southern WV. Each case history is classified according to the degree of multiple-seam interaction, ranging from no apparent interaction to severe interaction with direct impacts on mine safety and resource recovery. The case histories are also examined with regard to amount and geologic characteristics of interburden and overburden, and design stability factors. The sequence of mining has also been found to be critical when the lower seam is fully-extracted. This paper compares current case histories to traditional rules of thumb. In addition two situations were modeled using LaModel software. LaModel has been upgraded to import pillar grids and topographic data from AutoCAD files. The cases presented demonstrate vertical stress capabilities of LaModel.

By Thomas P. Mahoney

Phelps Dodge Corporation's Tyrone Mine is a large open pit copper operation located in the southwestern corner of New Mexico. The Tyrone concentrator processes approximately 50,000 tons per day of copper ore. The waste ratio for this operation is 3:1; e.g., for every one ton of ore mined, three tons of waste material are also removed. This results in a mining rate of about 200,000 tons per day.

Jan 1, 1986

By G. Y. Chin, M. T. Dolan, W. L. Mammel

In the case of plastic deformation by slip, von Mises&apos; showed that an arbitrary shape change of a crystal generally requires the activation of five independent slip systems. The selection of the five active systems was worked out by Taylor ,&apos; who hypothesized that, among all combinations of equivalent slip systems which are capable of accommodating a given imposed strain, the active combination is that one for which the sum of the absolute values of the glide shears is a minimum. Taylor analyzed the case of {lll}( 110) slip for fcc metals and applied the analysis to crystals undergoing axisymmetric flow, which approximates the shape change of an embedded grain in a polycrystalline aggregate deformed in tension (or compression). For the twelve equivalent (111) (110) slip systems, there are 384 independent combinations of five slip systems that satisfy the imposed strain.&apos; Taylor laboriously calculated the value of M = ZjIyj /E for each combination (although some were missed) and obtained the minimum M, hence the active combination, for a number of axial orientations distributed throughout the stereographic triangle. (yj is shear from slip on the th system and e is the tensile strain). Detailed contours of constant minimum M were recently obtained by Hosford and Backofen using a simplified but equivalent Bishop and ill&apos; analysis. Due to the numerous combinations of slip systems involved in the calculations, however, the full potential of the powerful Taylor analysis has not been exploited. For this reason, we have recently utilized techniques of linear programming to obtain solutions of the Taylor analysis for axisymmetric flow, for slip on {110)(< 111), {112)(111), and {123)(111) systems as well as mixed slip composed of these three systems. These slip modes are of obvious importance in the deformation of bcc crystals. Some of the salient results are summarized below. 1) Stress-Strain Data for Polycrystal. The value of M averaged over all axial orientations is the ratio of the tensile flow strength of a randomly oriented aggregate to the critical resolved shear stress for slip. This value enters importantly in theoretical deductions of the polycrystalline stress-strain curve from single-crystal data.2&apos;3&apos;5 Table I lists the values of Ma,, for the several cases of slip, as obtained by the present computer work. 2) Texture Hardening. Since the value of M depends on the axial orientation, the (tensile) flow strength of a specimen may be increased through texture control.&apos; An example of the computer results is shown in Fig. 1, where contours of minimum M have been computer-plotted for the case of mixed slip on {110}(111), {112)(111),and {123}(11 1) systems. It may be seen that, under axisymmetric flow, wires of (111) and (110) axial orientations are 50 pct stronger than those oriented at (100) .

Jan 1, 1968

By John Ellenberger

The nature of competition in the coal market tends to deplete the most favorable coal reserves first, and forces subsequent development of mines in more extreme ground conditions such as those associated with multiple-seam mining. In fact, 70% of the United States coal reserves are in multiple-seam situations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop mine design algorithms that will result in safer multiple seam mines. This paper presents an overview of multiple seam issues in the central Appalachian coalfields. To date, more than 50 case histories have been analyzed from 20 operating mines in Eastern KY, Western VA, and Southern WV. Each case history is classified according to the degree of multiple-seam interaction, ranging from no apparent interaction to severe interaction with direct impacts on mine safety and resource recovery. The case histories are also examined with regard to amount and geologic characteristics of interburden and overburden, and design stability factors. The sequence of mining has also been found to be critical when the lower seam is fully-extracted. This paper compares current case histories to traditional rules of thumb. In addition two situations were modeled using LaModel software. LaModel has been upgraded to import pillar grids and topographic data from AutoCAD files. The cases presented demonstrate vertical stress capabilities of LaModel.

Jan 1, 2003

By L. I. Hewes, Joseph W. Roe

A graphic solution of Kutter&apos;s formula for the flow of water has been worked out by Dr. L. I. Hewes in connection with his course in Graphic Computations, given in the Sheffield Scientific School, Yale University, which may be of interest to those who deal with canals, flumes and streams. 1.811 0.002811 , 41.66+ -n+-S- I Kutter&apos;s formula, V= - n 0 .00281 78- 1+(41.66 + 0.00281)7B781 is probably the most accurate of those proposed determining the flow of water. But it is extremely cumbersome, and if many calculations are to be made their solution becomes drudgery. The purpose of this chart, Fig. 1, is to furnish a rapid solution, sufficiently accurate to be well within the limits of the observed data. The chart consists essentially of three parallel scales, one for the mean velocity, V, one for the hydraulic radius, R, and one for the slope; a diagonal line, not graduated ; and a set of curves for the various values of n, the factor which involves the na-

Jan 1, 1910

By R. C. Mahon

Operators concerned with the destruction of their piping by acid mine waters will be interested in the method by which this problem was solved at the Cardiff mine of the Homer group. Rubber lined, or acid resisting metal pipes were found too expensive. Casting concrete lining in pipe would have required a minimum thickness of one inch, thus excessively reducing the pipe&apos;s diameter, as well as taking twenty four hours per length of pipe. The Naylor Pipe Co. of Chicago, having experimented with centrifugal lining of pipe with concrete, provided information which eventually solved the problem. An experimental plant was constructed as shown, and the following procedure developed : (1) Kerosene is used to remove the interior oil coating of new pipe. Closed with blank flanges, the pipe is revolved for eight minutes at varying speeds. Stopping and starting the motor achieves a good washing action. The kerosene is then drained off, and similar washing action with caustic soda removes any excess. Swabbing in done with burlap fastened to a 1/2-in. pipe. (2) The aggregate, made of one. part quick-setting cement and two

Jan 1, 1949

By J. A. Reizes, C. A. J. Fletcher, T. Jancar

Spirals play an important role in fine coal and mineral processing. To date, almost all spiral designs have been empirically based. Although many operational units have evolved utilising this approach, it does not necessarily lead to optimal spiral designs. This paper presents the preliminary results of a collaborative computational and experimental research program to understand the detailed separation process which will ultimately lead to a parametric assessment of alternative spiral designs through computational simulation. Unlike the empirical approach, a computational simulation is only subject to the fundamental physics of the fluid flow. No prior knowledge of the generic spiral flow is necessary. The computer code implements a robust finite volume technique to predict the three dimensional fluid motion. A height function method is used to model free surfaces and the code is capable of handling arbitrary spiral geometries. Preliminary validation of the computational simulation is carried out through analysis of an existing spiral design -the Mineral Technologies LD9 unit. Computational flow predictions are compared with experimental measurements obtained using a number of techniques, including sampling and flow visualisation, for flow test cases where no solid particulate is present.

Jan 1, 1995

By Melissa L. Trapani

The removal of molten products from metallurgical furnaces is one of the most hazardous and labour intensive processes in a non-ferrous smelter. The proximity of operators to the molten metal and slag during tapping and the oxygen lancing that facilitates the flow have led to many reported injuries on tapping floors. In most cases, tapholes are opened and closed periodically leading to extreme thermal cycling in the tapping assembly. As a consequence, refractory wear rates are high and unpredictable in the taphole. This paper provides a review of the current state of taphole development, and gives a methodology that is now being applied to gain a better understanding of the taphole region to allow design improvements.

Jan 1, 2002

By Duncan B

Shortwall continuous mining as first introduced at Burwood colliery, and currently being used at John Darling, Lambton, and Corrimal collieries, is a method of coal winning which was pioneered in the Newcastle district. The system uses individual hydraulic self-advancing chocks for roof support and the coal winning operation is by continuous miners and shuttle cars. Where physical conditions are suitable the system provides a safe, efficient and economically viable basis for pillar extraction. Shortwall operations have been conducted successfully in the Victoria and Dudley seam, near the coastal fringe of the Newcastle district and are now being tried out in the more difficult conditions of the Bulli seam in the Illawarra district.

Jan 1, 1972

By AIME AIME

ALTHOUGH the retiring Chairman of the Industrial Minerals Division, Charles Henry Behre, Jr., does not say "you all" he is a product of the deep South, since he was born at Atlanta, on March 16, 1896. At the Boy Scout age he moved to New Orleans, where his father owned an ice plant, which seems an intelligent business for that climate. Intelligence evidently runs in the family, for Charlie, as his friends call him, has one sister who is a professor of zoology and another who is a concert pianist. Charlie has no explanation of why, when he reached college age, he decided to go to the University of Wisconsin, other than something more than an ordinary boyish interest in science, and the reputation which Wisconsin then enjoyed. At Madison he fell under the influence of Eliot Blackwelder, chose paleontology as his objective, and transferred, at the end of his sophomore year, to the University of Chicago, where the paleontological panorama seemed more extensive. He took his B.S. there in 1918, and graduated into the U. S. Army, where he eventually became a Sergeant in the Medical Corps.

Jan 1, 1945

By A. Geoffrion, L. J. Cousineau

In underground powerhouse excavations, the access to the horizontal sections of the penstocks is most often critical. Other factors which influence the schedule include: the sequences of excavation, the interface dates between contracts, the type of support for the overhead cranes and whether the roof in the powerhouse is a reinforced concrete arch or a suspended prefabricated material. At Outardes 3, Churchill Falls and LG-2, these factors, along with the size of the powerhouse and the local topgraphy and geology were studied to produce the optimum schedule.

Jan 1, 1983

By W. M. Moon, Hugh G. Miller, C. -S. So

"Digital image processing and enhancement techniques have been applied to airborne gamma ray spectrometry data from Sudbury, Ontario. These results have been correlated and compared with the available geological maps to evaluate their usefulness for identifying lithological units. Digital processing allows the correlation of various data sets, and different combinations of images can be tested and viewed as a composite image. Composite images with pseudocolours provide an opportunity to analyze and correlate information that is not otherwise apparent in individual images. Principal component analysis has been applied to the gamma ray spectrometry data to evaluate their efficacy and relative information contents of the measured and computed data. The results of this study indicate that the combined radioelements image (obtained by combining the radioelement image and the ratio images) is effective for defining areas of relative concentration of a specific element in near surface materials. Furthermore, the composite radioelements image (produced by combining three separate radioelement images) and composite principal components image reflect large-scale lithological variations. IntroductionThe Sudbury area is a unique geological structure located in the southern Canadian Shield (Fig. 1). Because the area hosts economically significant nickel-copper deposits (Pye et al., 1984), it has been surveyed in great detail by geological and geophysical methods. In order to obtain meaningful geological infonnation about the Sudbury area, several studies have been carried out with the application of innovative mathematical techniques for geophysical modelling, and attempts have been made to integrate the multisensor geophysical data available for the area (e.g. Gupta et aI., 1984; Moon et al., 1988; Singh et al., 1993). The main objective of this paper is to apply digital image processing and enhancement techniques to airborne ganuna ray spectrometry data in order to determine their usefulness for regional geological mapping."

Jan 1, 1994

By J R. Manuel, M J. Peterson

Selected drill core samples from a Ferrobamba-limestone-hosted, magnetite-haematite skarn deposit, located in the Apurimac department of the Andahuaylas-Yauri skarn/porphyry belt of south-eastern Peru, were mineralogically and texturally characterised to gain a preliminary indication of the deposit&apos;s potential as an iron ore resource. Optical microscopy, X-ray diffraction (XRD) and scanning electron microscopy/electron probe microanalysis (SEM/EPMA) techniques were utilised to determine the characteristics of magnetite, haematite and/or goethite dominated ore types, including variations in the relative proportions and textural relationships of the ore and gangue minerals. The deportment of elements deleterious to processing performance (eg copper, sulfur and potassium) was determined and the beneficiation potential of the samples was briefly assessed. In drill core sections, the ores are grey to reddish in colour, massive and &apos;metallic&apos; to dark brown and earthy in character, moderately hard and porous (macro and microporous), with variable gangue infill. Ores often appear weathered, typified by ochreous goethite staining and common minor goethite (except in dense core fragments), occasionally exhibiting a more friable texture with coarse magnetite/martite grains. Silicates and lesser carbonate gangue are visible as blue-green to beige to white scaly and/or shaly surface coatings, and finely particulate infill, often goethite stained. Sulfide-rich ore types also occur in part of the deposit, but are restricted to specific drill holes. Magnetite grain size is relatively coarse, compared with magnetite from typical banded iron formations, whereas discrete silicate gangue is mainly bladed/fibrous and/or layered and micaceous in form. XRD analysis indicates the presence of vermiculite, serpentine, stilpnomelane, chlorite, actinolite and clays. There is a spectrum of ore types representing the gradation from &apos;fresh&apos; (magnetite-dominated) to oxidised and weathered (martite/goethite-dominated). Martite-dominated samples are generally higher in grade, due to leaching and removal of silicate gangue, resulting in higher macroporosity. Where gangue has been leached out, partial replacement by vitreous goethite and/or hydrohaematite is typical, often preserving the fibrous/layered characteristics of the original silicates.

Jan 1, 2009