Search Documents

By Cashman R. S. Mason

Removal of halides (fluoride, chloride) from metallurgical solutions can reduce corrosion rates and improve hygiene from decreased anodic chlorine evolution. This is particularly true for zinc sulphate electrowinning solutions. This paper describes the chemistry of a new process for the removal of halides from such solutions by solvent extraction ? the Teck Cominco Halogon? process, for which patents are pending. In this process, the halides are loaded directly from commercial zinc sulphate solutions and are stripped into a form suitable for disposal. Sulphate extraction efficiency is variable while maintaining halide extraction efficiency. The method of optimizing the solvent composition is demonstrated.

Jan 1, 2003

By Neil Styler

This paper presents an analysis of measurements of inter-burden deformations above six longwall faces. An attempt is made to demonstrate some correlation between the movements at the various sites, and to examine their importance with respect to predicting caving height, disruption of overlying seams, and disruption of aquifers. This analysis demonstrates some significant differences between predicted surface subsidence, and inter-burden deformation. In addition it is shown that the caving height above a longwall face is equal to 8 to 12 times the extraction height, with a zone of fractured rock extending to approximately 50 times the extraction height above the seam.

Jan 1, 1984

By V. T. Taniguchi

A process for large scale chromatographic separations using a continuous chromatography technique is described. The process combines the advantages of large scale batch fixed column displacement chromatography with conventional analytical or elution continuous annular chromatography (CAC) to enable large scale displacement chromatography to be performed on a continuous basis (CDC). Such large scale, continuous displacement chromatography separations have not been reported in the literature. The process is demonstrated with the ion exchange separation of a binary lanthanide (Nd/Pr) mixture. The process is, however, applicable to any displacement chromatography separation that can be performed using conventional batch, fixed column chromatography.

Jan 1, 1989

By D R. Rankin, J J. Fuykschot

Forrestania Nickel Mines is owned and operated by Outokumpu Mining Australia Pty Ltd and is situated 400 km east of Perth, WA in the Forrestania Greenstone Belt. Production started in late-1992 at a rate of 600 ktpa and reserves were exhausted in August 1999. Cosmic Boy is the largest of three mines worked and operates in a high stress environment with both very high and very low rock mass strength domains. Stoping commenced in 1995 using conventional benching with long hole slot rises but because of drilling and blasting problems the mine switched to airleg rising. In 1997 the mining method was changed to smaller scale up hole retreat benching with each stope requiring a slot rise of up to 16 m length. This method does not allow top access to the rise location and so airleg rising was used until mid-1998. At this stage mining was approaching areas of higher stress for which it was clear that an alternative to this entry method of rising was required. Small diameter raise boring and Cubex rigs were considered but because of the set up costs were not considered to be viable. Since the ore is relatively soft, burn cuts were developed to make use of specially designed 152, 203 and 254 mm diameter reamer bits (depending on the rise length) and drilled with conventional long hole drilling equipment. These rises are fired in one blast together with the slot rings. In the northern lower section of the mine (below 400 m) the principle stress has been estimated at 60 MPa and this causes minor strain bursting in BIF development headings and loose material to form on walls and backs. Trials of destress blasting modelled on Canadian experience has greatly reduced strain bursting at the face. However only around 300 m of development was affected and so this method had not been optimised when mine development was completed.

Jan 1, 1999

By Taner Sumer, H Altay Guvenir

Fragmentation in rock quarries is tried to be achieved by changing the specific charge, drill pattern and bore hole diameters by different experts. This paper is a brief summary consisting of the utilization of practical experiences of the other group on cost optimization procedure that takes into account blasting, transportation and crushing as a whole process and optimize the cost by defining the optimum gelatin based explosives to be used as a main primer of anfo in three different limestone and granite quarries, with similar rock characteristics.

Jan 1, 1993

By R. A. Burmeister, P. E. Greene

Two methods for the synthesis and growth of single crystals of B6 P are described: a solution-growth process employing nickel as the solvent, and a vapor-growth process employing BBr3 and pH3 as the reac-tants. Relevant portions of the Ni-B-P phase diagram have been examined and liquidus data are presented for an isobaric section at an equivalent P2 pressure of 3.8 Torr, and an isothertnal section at 1300°C. Solution-growth techniques are described and the purity and crystalline perfection of the resulting material is discussed. Epitaxial growth of BeP on &P substrates has been obtained using the vapor-phase system. Evidence is presented which supports the assignment of the stoichioknetry B6P to boron sub-plwsphide. THE B-P system differs from other III-V systems in that it contains two distinct compounds. The existence of the monophosphide (BP) has been known for some time,' whereas the subphosphide (B6P) was reported only recently.' Both of these compounds are large bandgap semiconductors (Eg = 2.0 ev for BP~ and 3.3 ev for B6P4), and are therefore of interest for optoelectronic applications. The crystal structure of B6P is quite different from those of most semiconductors, being derived from that of a-rhombohedral boron by the incorporation of the two phosphorus atoms in the intericosahedral sites of the a-boron unit cell?76 B6P also exhibits a number of unusual characteristics, including a high degree of chemical inertness, hardness, and high-temperature stability. No information concerning other physical properties is available in the literature. The present study is part of a broader investigation of the preparation and properties of B6P. This paper considers methods of growing single crystals of B6P of suitable size and quality for physical-property measurements. A detailed discussion of the electrical and optical properties of B6P will be given elsewhere.' GENERAL CONSIDERATIONS The method first used to synthesize B6P was the disproportionation of BP' according to the reaction The equilibrium P2 pressures corresponding to this reaction were also determined .'" It is therefore possible, in principle, to apply several of the reactions reported for the synthesis of BP to the synthesis of B6P merely by selecting lower phosphorus pressures or higher temperatures, in accordance with the equilibrium data. Other techniques for the direct synthesis of microcry stalline B8P have also been reported.1°

Jan 1, 1968

By D. Kang, K. N. Han

The adsorption behavior of silver in ammoniacal solutions on activated carbon was studied. In addition to the concentration of ammonia, the parameters that affect adsorption include temperature, degree of agitation and anion and cation concentrations. In the study, it was found that the adsorption of silver from ammoniacal solutions is dependent on the initial silver concentration in the solution. It was also found that the recovery of silver from ammoniacal solutions is not as effective us gold. The adsorption rate was relatively slow overall, despite a rapid initial adsorption. The apparent activation energy ,for the adsorption was measured at 30.2 kJ/mol. It was believed that the kinetics of the silver adsorption on activated carbon was limited by a mixed control mechanism.

Jan 1, 1999

This Association is made up of Alabama members of the following technical societies: The American Society of Civil Engineers, American Institute of Mining Engineers, American Society of Mechanical Engineers, American Institute of Electrical. Engineers, American Chemical Society and the American Institute of Architects. The association organized last winter for the purpose of maintaining an organization among the technical men of the State of Alabama, to stimulate the development of the natural resources of the State, to foster public interest in all things beneficial to the State, to advance the interest of the technical profession in the State and to encourage social intercourse among its members. On June 30, 1917, an excursion was made to the power house of the Alabama Power Co. at Lock 12 on the Coosa River. This is the first meeting held outside of Birmingham and is also the first meeting to which ladies were invited. About 85 members and guests attended and the excursion was voted a great success by all present.

Jan 8, 1917

By R. A. Halatchev

Historically two basic approaches of production sequencing have been formed in the theory of open pit mine design. The first approach implements a technological discretization of the pit space within the ultimate pit outlines where the minimum working width is the limiting technological factor. The second approach uses a pseudo-economic discretization based on the implementation of analytical methods for designing intermediate/ultimate pit outlines and the concept of pit shells generation. The paper offers an elaborate analysis of both approaches used currently for discretization of the geological medium into working benches and modelling the working zone of open pit mine. The analysis is extended with a new vision for unification of the mining systems in open pit mine design under the form of a classification. A comparison of the approaches is provided to illustrate their advantages and disadvantages with regard to the implementation of the principle of waste deferment as one of the main principles of mine planning that exploits the time effect of money.

Jan 1, 2003

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill both in MICAF sills and in recovery of major horizontal pillars in the 650 copper orebody, where, during mining, cemented fill has regularly been exposed on unsupported vertical faces up to 90 ft high. In the paper the main considerations are the role and specifications of the fill used but also included is a brief description of fill preparation and placement.Data resulting from a Portland cemented hydraulic fill sampling, curing and testing campaign covering about 18 months of operating practice are presented, analysed, and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. The data collected showed that the fill station can operate within tolerances set on product quality, that laboratory and field strength results are comparable, and that rapidly obtained fillsample properties such as moisture content and void ratio can be related to cement content and strength, and hence used for quality control.Results of a fill research programme conducted by the author in Mount Isa since early 1968 are presented involving Portland cemented hydraulic fill and alternative, cheaper additives for cementing hydraulic fill. The most significant alternative to Portland cement is quenched and ground copper reverberatory furnace slag, whIch behaves as a pozzolan, reacting strongly with any available lime to produce cementitious hydrated calcium silicates and allowing Portland cement reductions of at least 50 per cent without strength loss.

Jan 1, 1971

By H. E. Montgomery

H. L. Burghoff.*—I have a question, Dr. Smith. A number of the alloys you mentioned contain lead, which, of course, is present as discrcte particles. At what level of concentration does lead begin to play an important part in determining these elevated-temperature characteristics ? A. J. Smith.—That is a difficult question to answer because of the complicating features of the alloys that arc lead free. I do not know of any work done on the subject. But for comparison, 85-5-5-5 has about the same characteristics at, say 450°F. as 88-10-2, which is lead free or contains at most 0.30 per cent. Both 85-5-5-5 and 88-10-2 precipitate delta. The specification limit of usage is 406°F., temperature of saturated steam at

Jan 1, 1945

By John A. Bischoff, Francis S. Kendorski

A technique that has been used for inspection and appraisal of rock tunnels is described. It enables a rapid and complete record to be made of those factors necessary for the engineering assessment of the rock conditions surrounding a tunnel. Full understanding of the regional geology, and a careful recording of data concerning the principal geological and construction factors is essential basic data for a tunneling project, whether the tunnel is under construction or is already in service. A methodical recording of data concerning general geology, shears, fracture orientations, spacing, persistence, rock classification, water condition, shear frequency, excavation method, blasting procedure, and rock stabilization and support methods, combined with a photographic record, can be completed by experienced engineers and geologists at the rate of over 1000 feet of tunnel per shift.

Jan 1, 1976

By George W. Huseman, W. D. Mcmillan

"INTRODUCTION Feldspars represent one of the most abundant groups of minerals and constitute nearly Go percent of the material contained in the igneous rocks. They are grouped in a series of related aluminum silicates with varying amounts of potash, soda, and lime. .Approximately 85 percent of the feldspar produced in the United States is used as a flux in the production of glass, pottery, enamel and sanitary ware, brick, and tile. Notwithstanding the abundance of feldspar in the earth's crust, the only deposits that are worked to any extent are the pegmatites or coarsely crystalline dikes where natural segregation of the constituents facilitates recovery of the feldspar with a minimum of free quartz, mica, tourmaline, garnet, and other iron-bearing minerals that are detrimental in most ceramic industries.Although there are three glassplants and numerous other ceramic industries in Texas, all of the feldspar used in these plants is from other States. In the Llano region of central Texas, however, there are numerous coarse pegmatite dikes consisting primarily of feldspar and quartz in ratios up to 3 to 1. One of the more important of these dikes is the Badu Hill deposit in Llano County, Tex., which was first described by Carl Chelf 4/ in 1942. Following an examination of the deposit by W. D. McMillan, engineer in charge of the Texas field office of the Bureau of Mines, in January 1946, a proposal was made to investigate the deposit by core drilling in cooperation with the Department of Ceramic Engineering, University of Texas. This report presents the results of the cooperative investigation, which was begun April 24, 1946, and completed May 17, 1946."

Jul 1, 1947

By R. S. Hendricks

During the past two years, Hecla Mining Co. has used shotcrete for ground support purposes with substantial cost savings. Hecla's experience indicates that shotcrete is an extremely effective ground support material which can be successfully employed in problem areas where various conventional systems would fail. To date, Hecla's use of shotcrete has been limited to openings where long-term high-quality support was required, to specific areas where exceptionally difficult ground conditions were encountered [ ] and, occasionally, to stope support. It is anticipated that when the necessary engineering and procurement of the components of an efficient materials handling system have been accomplished, shotcrete will be used on a routine basis in stoping and development situations. The real future of shotcrete is based, however, on the fact that this form of support offers greater opportunity for mechanization than rock bolt, timber or steel. Unlike all other support operations, which are cyclic, shotcrete is a continuous process, and therein lies its potential for incorporation into an efficient rapid excavation system. Hecla has obtained and operated both wet- and dry-process shotcrete application equipment. The operational characteristics of the two processes are presented and discussed below.

Jan 1, 1970

By J. J. Kollé

A compressed-water hydraulic pulse generator (HPG) for nonexplosive blasting of rock and con¬crete is described Energy is stored in the HPG by compressing water to ultrahigh pressure. A large, fastopening valve discharges the com¬pressed water, resulting in a high-energy impulse. The HPG can be used for small-scale bench blasting by discharging the water through a nozzle that is closely fitted into a borehole. A bench blasting system requires an HPG, a drill and an indexing mechanism to allow insertion of the HPG nozzle into a drilled borehole. Systems with discharge energies ranging from 40 to 250 kJ have been used to excavate hard rock, including andesite, granite and quartzite. The largest system can excavate 15 t/h (16.5 stph) of massive quartzite based on a 2-min cycle time for hole drilling. Blasting with an ultrahigh-pressure hydraulic pulse generator was demonstrated as an effective means of excavating hard massive rock under the confined conditions of a tunnel opening or underground sloping panel. Hydraulic blasting provides a continuous mechanized mining capability that is well suited for deep-level mining and urban excavation sites where explosives are prohibited

Jan 1, 1997

By J. J. Kollé

A compressed-water hydraulic pulse generator (HPG) for nonexplosive blasting of rock and concrete is described. Energy is stored in the HPG by compressing water to ultrahigh pressure. A large, fast-opening valve discharges the compressed water, resulting in a high-energy impulse. The HPG can be used for small-scale bench blasting by discharging the water through a nozzle that is closely fitted into a borehole. A bench blasting system requires an HPG, a drill and an indexing mechanism to allow insertion of the HPG nozzle into a drilled borehole. Systems with discharge energies ranging from 40 to 250 kJ have been used to excavate hard rock, including andesite, granite and quartzite. The largest system can excavate 15 t/h (16.5 stph) of massive quartzite based on a 2-min cycle time for hole drilling. Blasting with an ultrahigh -pressure hydraulic pulse generator was demonstrated as an effective means of excavating hard, massive rock under the confined conditions of a tunnel opening or underground sloping panel. Hydraulic blasting provides a continuous mechanized mining capability that is well suited for deep-level mining and urban excavation sites where explosives are prohibited.

Jan 1, 1998

By R. C. Beckstrom

Russia's first "Petaletka'' has ended. Technically it did not succeed but practically it has been a great achievement in the petroleum industry. Out of the chaos of revolution and civil war Russia has developed her oil industry to second place in the world's production. For 1932 production of crude oil is estimated at 150,000,000 bbl. and refined products at 145,000,000 barrels. Russia has been able to give the petroleum industry every advantage that a government can extend to a fast growing industry. She has obtained all of her property by confiscation. Under government ownership, operation and control, her petroleum industry is not handicapped in any way by state rulings or by unnecessary competition in production, refining and marketing. There are no damage suits resulting from offsetting, flooding, repressuring, laying of pipe lines, building of docks or other necessary work. Russian oil fields2 have been easy to develop and operate. They lie advantageously to transportation for foreign markets. The chief disadvantages have been a lack of credit and technical cooperation, but the former is being overcome by the sacrifice of the people. They go without the comforts of life that all salable articles may be exported for the imports of modern machinery. Modern machinery is fast replacing the obsolete and worn-out equipment. Technical cooperation has been difficult because it has been necessary to train thousands of adults to do technical and mechanical work. Great quantities of pipe, tools and electrical equipment were necessary for the rapidly developing fields and refineries. The supplies have been inadequate and the quality poor. This lack of equipment, along with the untrained technical supervision, has been the cause of the proposed quota falling short. Fig. 1 shows the production for 1931 and 1932. During 1932 a large percentage of the oil was produced in the proven fields of the Caucasus.

Jan 1, 1933

By C. F. Quest, T. S. Washburn

The steel industry has a definite need in its tonnage mills for a formula relating expected tensile strength to the analysis of the steel. The McWilliam-Barnes1 and other less comprehensive formulas are used for this purpose, but these formulas were designed for an analysis range that does not include the medium manganese and silicon-bearing steels. This type of steel is being produced to meet the demand for tensile strength slightly higher than that of ordinary structural steel but not high enough to justify expensive alloy steels. The purpose of this paper is to present a somewhat more comprehensive formula based on data accumulated over a number of years by the Inland Steel Co., and to discuss the method followed in obtaining a formula to fit the data. The resultant formula admittedly is still weak in some respects, but for the expanded analysis range appears to be an improvement over the other formulas. It is hoped that with the collection of more data and possible collaboration with other mills studying this problem it will be possible to work out a more nearly perfect formula. Several publications have been issued on this subject. In some, the equation type of relation was evolved while others made a combination of tables and an equation. The latter include work by Campbel12,3 and Webster.4,5 Campbell classified the steels as acid and basic and applied a different formula to each. For basic steels, he used the equation: Teosile etrength = 41500 + 770C + 1000P + yMn [1 y was a variable depending on the carbon and manganese content of the steel and was listed in tables. Webster investigated acid Bessemer steel and developed the equation: Tensile strength = 38000 + 800C + xTP+ yMn [2]

Jan 1, 1940

By C. F. Quest, T. S. Washburn

The steel industry has a definite need in its tonnage mills for a formula relating expected tensile strength to the analysis of the steel. The McWilliam-Barnes1 and other less comprehensive formulas are used for this purpose, but these formulas were designed for an analysis range that does not include the medium manganese and silicon-bearing steels. This type of steel is being produced to meet the demand for tensile strength slightly higher than that of ordinary structural steel but not high enough to justify expensive alloy steels. The purpose of this paper is to present a somewhat more comprehensive formula based on data accumulated over a number of years by the Inland Steel Co., and to discuss the method followed in obtaining a formula to fit the data. The resultant formula admittedly is still weak in some respects, but for the expanded analysis range appears to be an improvement over the other formulas. It is hoped that with the collection of more data and possible collaboration with other mills studying this problem it will be possible to work out a more nearly perfect formula. Several publications have been issued on this subject. In some, the equation type of relation was evolved while others made a combination of tables and an equation. The latter include work by Campbel12,3 and Webster.4,5 Campbell classified the steels as acid and basic and applied a different formula to each. For basic steels, he used the equation: Teosile etrength = 41500 + 770C + 1000P + yMn [1 y was a variable depending on the carbon and manganese content of the steel and was listed in tables. Webster investigated acid Bessemer steel and developed the equation: Tensile strength = 38000 + 800C + xTP+ yMn [2]

Jan 1, 1940

By C. F. Quest

THE steel industry has a definite need in its tonnage mills for a formula relating expected tensile strength to the analysis of the steel. The McWilliam-Barnes1 and other less comprehensive formulas are used for this purpose, but these formulas were designed for an analysis range that does not include the medium manganese and silicon-bearing steels. This type of steel is being produced to meet the demand for tensile strength slightly higher than that of ordinary structural steel but not high enough to justify expensive alloy steels. The purpose of this paper is to present a somewhat more compre-hensive formula based on data accumulated over a number of years by the Inland Steel Co., and to discuss the method followed in obtaining a formula to fit the data. The resultant formula admittedly is still weak in some respects, but for the expanded analysis range appears to be an improvement over the other formulas. It is hoped that with the collec-tion of more data and possible collaboration with other mills studying this problem it will be possible to work out a more nearly perfect formula. Several publications have been issued on this subject. In some, the equation type of relation was evolved while others made a combina-tion of tables and an equation. The latter include work by Campbell2,3 and Webster.4,5 Campbell classified the steels as acid and basic and applied a different formula to each. For basic steels, he used the equation: Tensile strength = 41500 + 770C + 1000P + yMn [1] y was a variable depending on the carbon and manganese content of the steel and was listed in tables, Webster investigated acid Bessemer steel and developed the equation Tensile strength = 38000 + 800C + xP + yMn [2]

Jan 1, 1940