Search Documents

By William O. Vanderburg

Some mines after passing through the prospecting stage and becoming sizable enterprises still adhere to the development program of the prospect, extending their workings without definite plans. In mining operations where definite structural conditions do not exist, a prearranged layout of mine development is not feasible; but where exploration and preliminary development have indicated the extent and probable limits within which the ore is expected, careful planning of development will result in a lowering of mining costs and a consequent increase is profits. A lack of definite plane for laying out mine workings is one of the contributory factors to unnecessarily high costs. Although this paper deals primarily with the influence of level spacing on mining costs, still other phases of mine development, such as the proper spacing of ore chutes and raises, can be analyzed on a cost basis in a similar manner, as shown herein. LEVEL SPACING The problem of establishing a new level or levels in order to exploit steeply dioping ore deposits and prospect the ground at depth recurs at intervals during the active life of mines. Driving levels is largely "dead work" and therefore costly. By the judicious selection of the proper level interval after balancing the opposing factors involved in the problem, a considerable saving in mining costs can be effected. Although much has been written in regard to the various methods employed in ore extraction, mining literature is still incomplete in regard to the factors-influencing level spacing at various mines. Level spacing involves procedures not lending themselves readily to description, and, moreover, it is a phase of mining operations that is apt to escape criticism, because only those in close contact with the operations are equipped with the necessary familiarity with the conditions to pass judgment.

Jan 1, 1932

By M. Pope

By 1950, packaged oil and gas fired boilers were on the market for capacities up to 30,000 lbs./hr. By 1962, capacities were up to 100,000 lbs./hr. and even higher when separate heat traps (economizers and air preheaters) were attached to the boiler packages. During this period, complete packaged coal fired boilers were developed into the 10-15,000 lbs./hr. range. Oil and gas fired plant designs became very compact, "basementless", and far: less costly than the coal fired plants of any capacity. Coal fired plants remained large and expensive, required field erection of boilers and required basements. With the spectacular strides made in automation, oil and gas plants became far less costly to operate, requiring only the part-time attendance of a single operator. Some advances were made in coal fired plants, but not to the degree attained by the fluid fuel competition.

Jan 1, 1965

By Richard L. Gordon

Coal supply analysis has since about 1973 become a major activity of many scholars and consulting firms. The present paper is an effort to explain in as nontechnical fashion as possible the state of the art and what implications, if any, the research has for those actually engaged in producing coal or regulating the industry. l The discussion stresses the coal supply side of the models and makes limited comments about other elements in the analysis. To orient the appraisal, it is desirable to recall the features of coal supply that an adequate model should capture. The first considerations are the locational aspects of the industry. Transportation costs can, in some cases, exceed the production costs of coal, and thus any adequate model must incorporate a treatment of the economics of transporting coal from one location to another. A second major issue is that of the heterogeneity of coal; models should treat as well as possible such key differences among coals as their Btu and sulfur content. Third, we recognize that, with given technology and labor, capital, and supply costs, an expansion of the supply of a given type of coal in a specific region will occur only if prices rise. This is the familiar proposition of textbook economics that supply is an increasing function of price. Finally, over time, changes in technology, input cost, and depletion interact to cause changes in the price of given amounts of coal. Economics represents the net effect of this process by a shift over time in the supply curve. During the 1950s and 1960s, the trend was to reduce the production costs of a given output; subsequently costs rose sharply.

Jan 1, 1977

By J. W. Rogers, S. K. Schwartz

"The Cape Breton Development Corporation (CBDC) is a federal Crown corporation which operates two coal mines (Phalen and Prince Collieries), a coal preparation plant, a railway, a central workshop and a deep water shipping facility.The Sydney coal field consists of 11 major seams, which range from 0.8 m to over 3.7 m in thickness. Of the 2.4 billion tonnes of known coal resources in the field, approximately 550 million tonnes can be mined with present mining technology. These parameters define reserves which extend more than 8 km beneath the ocean to a depth of 1200 m. With today’s design and present high production faces, the colliery life is projected at approximately 20 years."

Jan 1, 1996

By S Slouka

Airborne rock dust poses serious long-term health complications to workers in the underground mining and civil environment where rock excavation is utilised. During drilling, airborne rock particles are immediately released into the breathable environment where additionally, the settled dust can be reintroduced into the air further down in production. The purpose of this study is to build a characterisation suite of dust particles such that underground operations can implement more appropriate dust suppression and mitigation techniques in accordance to pick wear. Therefore, concrete is cut to create a preliminary dust characterisation baseline, where future cutting tests will be performed on limestone and sandstone rocks.In this study, three conical pick wears (new, moderately worn, and fully worn picks) are used to generate dust from a concrete block and characteristics are statistically compared between the dusts. Airborne respirable particles are collected during cutting and deposited fine material, orparticles left on the surface of the block, are collected after cutting. The dusts are then analysed through standardised methods, field emission scanning electron microscope image capture with image analyses, and laser diffraction methods. Findings reveal that the worn pick generated thehighest concentration of respirable dust, all picks generated dust containing quartz, the three picks generally generated respirable dusts with similar particle shapes (in terms of roundness, roughness, and aspect ratio), and the worn pick generated the largest deposited fine material particles.

Oct 12, 2022

By O. C. Blade

"INTRODUCTION This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1952 was mode under a co¬operative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior.Analytical data are presented for 94 samples of aviation gasoline which include for the first time in this series of reports, data on five samples of grade 108/135 aviation fuel. Data also are given for 34 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers' production in their laboratories and the results sub¬mitted to the Bureau of Mines for compilation. The products of 20 manufacturers of aviation gasolines and of 16 producers of aviation jet fuels are represented.SUMMARYA comparison of certain properties of the commercial aviation gasolines produced in the United States during 1950, 1951, and 1952 is presented in table 1, the 1952 data being average values from tables 3 through 7 of the present report. Trends in certain characteristics of these fuels may be seen in figures 1 through 5 which also indicate the minimum and maximum values. As may be observed, the properties of commercial aviation gasolines have not varied greatly during recent years. A list of aviation-fuel survey reports published by the Bureau of Mines is given on page 7.Table 2 presents a summary of data from table 8 and compares properties of aviation jet fuels of 1952 with summarized data on jet fuels of October 1951."

May 1, 1953

By Ray Mason, Damien Label, Howard Bernier, Kevin McDermott, Kevin Coombs

"GeneralWabush Mines is an unincorporated joint venture of seven steel companies and Pickands Mather & Co. The mining and concentrating facilities are located in southwestern Labrador and the pelletizing and shiploading facilities are at Pointe Noire, 200 miles south, near the town of Sept-lies.The operation is based on a 5 ½ sq. mi. specular hematite deposit with a reserve of 375 million tons of concentrate. Annual production capacity is rated at 6 million tons of pellets per year. The final upgrading process utilizes high-tension separation of silica following wet autogenous grinding, spiral gravity separation and fluo-solids drying. The concentrate is railed in closed cars to Pointe Noire. The concentrate is reground dry and pelletized on Dravo Lurgi travelling grate machines to produce an oxide pellet with 65.5% Fe, 3.0% Si02, 1.95% Mn and 93.5% Tumble Index.HistoryPlant operations commenced in 1965 with a concentrator capacity of 5.3 million tons per year and a pelletizing capacity of 4.8 million tons per year. The original facilities for classifying the crude ore into fine and coarse fractions for storage purposes before reblending as autogenous mill feed were found to be unnecessary and were by-passed after plant startup. Capacity of the operation was increased to 6.0 million tons of pellets per year in 1968. This increased capacity required the installation of an additional160 cleaner spirals in the ore dressing plant, a new 5000 hp ball mill, three balling circuits and increased cooling air capacity in the pellet plant.In 1970, the regrind circuit in the pellet plant was converted to dry grinding and a significant reduction in grinding media consumption and maintenance costs was realized. A ninth grinding mill of 5000 hp capacity was installed to compensate for the reduced capacity in going from wet to dry grinding."

Jan 1, 2000

By S. Peng, N. Vayenas, A. Farah

"While genetic algorithms have been widely adopted in ore grade estimation and optimization, mine design, and production scheduling in the mining engineering field, reliability and maintainability analysis of mining equipment using genetic algorithms has been a relatively new research area in recent years. This paper presents an application of genetic algorithms using case studies with seven underground scoop trams whose maintenance records have been collected over a period of 12 months from an underground mine in the Sudbury mining area. Based on the assumption that various factors that contribute to machine failures resemble the biological evolution process, the authors have developed an in-house PC software application called GenRel which adopts genetic algorithms in its programming. In this study, the authors feed the historical maintenance data into GenRel in order to predict future maintenance characteristics of mining equipment in a time period of three months. Then the predicted maintenance characteristics are compared to the actual maintenance records in the same time period. A statistical study is then used to examine the similarity between the predicted data and the recorded data.INTRODUCTION Today maintenance costs of sophisticated engineering systems are so high that maintainability draws great attention from scientific researchers to operations managers. For instance, a study by [1] shows that American manufacturers spend more than 300 billion U.S. dollars on plant maintenance and operations. Therefore it is understandable that the main objectives of applying maintainability principles to engineering systems are to reduce projected maintenance costs, to use maintainability data to estimate system or equipment availability/unavailability and to determine labor-hours and other related resources needed to perform the projected maintenance. A system with better maintainability would inherently provide the benefit of lower maintenance costs, less time to recover with lower breakdown frequency (design for simplicity), less complexity of maintenance tasks and relatively reduced man-hours [2]. Most maintainability functions use the Time To Repair (TTR) as the independent variable. It is common to use probabilistic or statistical concepts to define a maintainability function, for example, the probability density function. Let t denote the time. Assuming a repair starts at t=0 and completes at time T, the maintainability can be mathematically defined [3] as in Equation (1)."

Jan 1, 2015

By G. S. Scott

The investigation of the causes, behavior, and control of anthracite mine fires, which the Bureau of Mines has been carrying on has yielded several publications directly applicable to mine-fire problems. 3/, 4/, 5/, 6/, 7/, 8/ As a further step in elucidating the causes of heating in certain anthracites subjected to oxidation, reliable information vial needed relative to the actual amount of heat that is liberated when a unit volume of oxygen combines with anthracite at varying temperatures.

Jan 1, 1939

By Caisa Samuelsson

Experimental studies in laboratory-scale equipment have been carried out to study the vaporisation from dust generated during the copper converting process. In the present work the vaporisation of Zn, Pb, As, Sb, and Bi from a dust collected in the electrostatic precipitator after the copper converter were studied. The results show that Pb, Bi and As were vaporised to a high degree from the dust at a temperature above 900°C in a gas containing N2, SO2 and a small amount of H2. The vaporisation was high for these elements also in a gas containing N2, SO2 and 02 at temperatures above 1120°C. In an earlier study, thermodynamic calculations showed that it is possible to selectively condense metals at high temperature' in a gas atmosphere generated during a copper converting process. The present study was carried out to verify the thermodynamic model. The results indicate that it should be possible for a selective condensation of Zn at high temperature. The temperature required for a selective condensation of Zn is dependent upon the gas atmosphere, e.g., the oxygen potential.

Jan 1, 1998

By L. H. Harrison

In coal mines equipped with electrically driven mechanical mining equipment, the problem of protection for electrical circuits and machinery important, because the hazards of fires and explosions resulting from electrical failures is greater than in most other industries. There is need for better methods and improved protective devices for this service. Studies and tests designed to determine possible value of the short-circuiting contactor as an electrical device for coal mine service were investigated. Preliminary made to determine the operating characteristics of the device, after which tests were made under actual service in three coal mines. Ordinarily, electrical protection in coal mines is divided into three classes, as follows: 1. Overload protection that is intended to protect against damage from overheating and excessive mechanical strain due to overloading. 2. Short-circuit protection that provides a means of de-energizing the equipment instantly when an accidental short circuit occurs in the equipment or on the power system. Short cm protection tends to damage from fires and, explosions resulting in the dissipation of large amounts of electrical energy in a short circuit. 3. Ground fault protection that, in its various forms, is intended, to maintain the frames of electrical equipment at or near the same potential surfaces in contact with the earth for the purpose of safe-guarding human life.

Jan 1, 1951

By Edwin W. Tooker

Creation of needed new resources will be accomplished mainly by imaginative and diligent geologic exploration because geologic availability is the key determinant of future mineral supply. Adequate resources of most commodities can be made available for the rest of this century and beyond if they are discovered. Thus conversion of hypothetical and speculative resources into available reserves will provide the principal challenge to earth scientists. Additional problems now compete for our attention. First is a challenge to discover more resources than have been found to date for domestic needs as world-wide demands increase exponentially and as easily found high-grade deposits are rapidly being depleted. New ways to find new types of deposits are required. Second, the United States, a resource importer, increasingly is challenged for access to foreign supplies through stiffening competition and economic or expropriation sanctions. Balancing needs for mineral supply and environmental protection is a third challenge. Geologic explorers must consider statutory as well as economic and technologic requirements, controlled access to public and private lands, competition with urban sprawl or wilderness, limitations on discovery, appraisal and mining methods, and restoration of mined areas. Finally, is the challenge to temper public and private attitudes and assure that decisions bearing on resource problems are based on comprehensive credible facts. While striving to maintain and improve the standard of living, many Americans appear to disdain and mistrust those organizations that provide their material where-withal. Meeting these challenges effectively, and in time, will require careful appraisal of the resource system and the joint efforts of industry, university, and government earth science research.

Jan 1, 1974

By J. C. Murray

Introductory: In dealing with a topic so large, one that involves such a multiplicity of details, and that also has certain controversial aspects, it is quite impracticable within the limits of this article to touch upon many most interesting phases and incidents. Also, to bring out the actual truth, it is necessary to make certain categorical statements. The writer believes that all such statements made here-under are supported by facts. Again, however, it is out of the question to cite all the proof. The writer, therefore, will gladly answer any pertinent criticisms or questions and thus supplement the unavoidable brevity of this paper. Controversial points will take care of themselves. Historical: For present purposes the history of gold mining in Nova Scotia may best be summed up in a very few paragraphs, in some of which the writer quotes freely from recent reports compiled by himself. The first material discovery of gold was made in the year 1860. As this and rapidly succeeding discoveries were looked upon as bonanzas, the claims were fixed at a size of 20 by 50 feet, and a yearly rental of $20 was charged. Later the claims (areas) were increased in size to 50 by 150 feet. In the year 1866 a temporarily successful company, so we are informed by a contemporary writer, owned a mill and mining plant worth $6,000. As this fact is cited with admiration, it is apparent that most of the mining and milling must have been done in a very primitive manner indeed.

Jan 1, 1926

By SIMON TIMBILLAH

The chalcopyrite-molybdenite (Cu-Mo) flotation industry is increasingly turning to organic depressants as suitable replacements for inorganic reagents, such as NaHS, due to environmental and safety concerns as well as high consumption rates of the inorganic reagents. This presents an opportunity for improvements or design and synthesis of alternative reagents. Disodium carboxymethyl trithiocarbonate (Orfom® D8) depressant is an organic depressant with a carboxylate group on one end and a trithiocarbonate group at the other end. Fundamental results are shown regarding the interaction of the Orfom® D8 depressant in the bulk flotation of a Cu-Mo concentrate from an operating North American mine. Cyclic Voltammetry on pure copper and Fourier Transform Infrared Spectroscopy (FT-IR) and X-ray Photoelectron Spectroscopy (XPS) measurements on pure chalcopyrite with Orfom® D8 depressant treatment are also reported. Through such characterization techniques a potential adsorption mechanism of Orfom® D8 on the mineral surface was identified and its depressant characteristics in the Cu-Mo flotation systems explained.

By D J. Bradshaw, B Lottermoser, A Parbhakar-Fox

"Best practice for acid rock drainage (ARD) risk assessment still relies solely on the geochemical properties of sulfidic rocks and mineral processing products, despite the fact that a rockÆs tendency to produce acid also depends on mineralogy and texture. Consequently, there are a plethora of geochemical tests routinely utilised by the mining industry to predict ARD formation. Due to limitations associated with these tests and their relatively high costs, analysis of recommended best practice sample numbers is rarely achieved, reducing the accuracy of waste management plans. Our research addressed this through examining the application of geometallurgical data for predicting acid formation, and led to the identification of potential environmental geometallurgy indicators.Samples obtained from an iron-oxide copper gold deposit were subjected to the geochemistry-mineralogy-texture (GMT) approach, an improved methodology for classifying acid forming potential. GMT results were compared against geometallurgical and assay data sets to evaluate: relative carbonate content measurements (measured by HyLogger) and identify how these could be used to calculate effective acid neutralising capacity mineral hardness (measured by EQUOtip) to determine application of this data for calculating lag-time to acid formation opportunities to automate the acid rock drainage index (ARDI) using classified images produced by a GEOTEK logger and automated microscopy.Links between the GMT approach and geometallurgical data sets were identified. Classified mineralogy data has application at stage one, HyLogger and EQUOtip at stage two and computer-based ARDI evaluations of classified images at stage three. Through such integration, ARD characterisation costs can be reduced, with value added to geometallurgical data sets. Furthermore, deposit-wide ARD domaining is possible, and acquisition of total-orebody knowledge more likely. Through adoption of this environmental geometallurgy approach, a better informed waste management plan can be formulated, allowing for best practice ARD sampling in a more cost-effective manner.CITATION:Parbhakar-Fox, A, Lottermoser, B and Bradshaw, D J, 2013. Cost-effective means for identifying acid rock drainage risks - integration of the geochemistry-mineralogy-texture approach and geometallurgical techniques, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 143-154 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By A. Perry

Latin America is in the path of economic growth characterized by increased privatization, joint-venture projects, and reduced trade barriers. Privatization is changing the industrial operating mode from Government-owned/Government-operated to a privately-owned/government-regulated regime. The establishment of joint ventures, such as in construction and management of infrastructure, energy and mining projects, and deregulated industries (electricity/gas/ telecommunications), is now a common practice in the region. These changes, coupled with the growing awareness of environmental protection issues, have led to a sincere effort on the part of the countries of Latin America to establish reasonable environmental regulations and controls (RERCs) for all industries, including mining and energy, for the benefit of present and future generations. However, RERCs require further consideration of many factors with respect to environmental, geologic, economic, and social impacts in the region. The process must find a balance between the need to sustain profitable operations and the need to adequately protect the environment. While striving to find a balance between continued industrial profitability and environmental protection, the RERCs must be scientifically sound, pragmatic, flexible, and enforceable. There has been worldwide attention focused on the environment, and international symposia have been held on such issues as global warming, water pollution, air pollution, and hazardous wastes. Organizations such as the United Nations (UN) and the Organization of American States have performed rather extensive studies on the environment for various industries and activities, and have developed some broad general plans to address environmental concerns. This technical information is available for the asking, and should be considered a starting point for countries embarking on the passage and enforcement of their own RERCs.

Jan 1, 1998

By Kefton H. Teague

An article entitled "The Rule of the Geologist in the Industrial Mineral Field" by G. R. Gullet, was published in the August, 1967, issue of the Canadian Mining Journal. Mr. Gullet defined industrial minerals as follows: "Industrial minerals are largely non-metallic minerals and rocks that find value because of their physical or chemical properties." This definition is brief, but all-inclusive. Mr. Gullet continues, "They include all useful minerals and mineral commodities except those used as fuels and those from which metals are extracted. Factors in the evaluation of an industrial mineral deposit are generally as different from those used in the evaluation of a metal deposit as is the assessment of a potential oil field. The key to the successful development of an industrial mineral, deposit is more often a balance of accessibility, transport, and proximity to markets than to any natural quality advantage of the deposit itself."

Jan 1, 1972

The role of a project metallurgist is diverse and covers input into the resource definition, mining studies, metallurgical test program development, process engineering and plant design, cost estimate preparation and financial analysis aspects of project feasibility studies. Mining project schedule and cost overruns can often be attributed to cutting short metallurgical test work, engineering and cost estimating leading up to commitment to development. In a significant number of cases this may result from the lack of understanding and commitment by the project proponent to the requisite metallurgical and processing studies required during the various pre-commitment stages of a mining project. Metallurgical test work, process development, engineering and cost estimating requirements for each stage of pre-commitment development are described together with a summary of the ongoing role of the project metallurgist during detailed engineering and commissioning of a process plant.

Jan 1, 2008

By John Newby, Mahmood Khwaja, Bernard Theron, Janice McGovern, Bernard Catalano, Michael S. Schultz

Launching a full-size pressurized-face Tunnel Boring Machine (TBM) in difficult ground conditions is always challenging. Recently, few projects have innovated the process by scaling the trenchless method of pipe jacking, and modified steel bell approach, to facilitate the launching of a full-size TBM without the need for large and deep trenches, starter/tail tunnels, or for incrementally installing supporting gear as the machine advances. This paper presents three such projects; evaluates the post-bid contractor proposed modifications; details the innovative use of pre-cast pipe segments to facilitate machine launch; and, provides an overall assessment of the benefits, challenges and lessons learned related to the modified approach.

Jun 13, 2021

By Long Meng, Yaodong Yi, Kuiyuan Chen, Zhancheng Guo, Yu Li

Blast furnace slag is the main by-product discharged in the iron and steel industry and contains considerable waste heat at dischargeing temperature between 1450 and 1550 °C. To fully utilize waste heat and slag, this study directly converted high temperature liquid Ti-bearing blast furnace slag into glass-ceramics via the “Petrurgic” method. Samples at different crystallization temperature were prepared and its influence on crystal phases, pore structure, and compressive strength were investigated via SEM, XRD techniques, and compressive strength measurements. Results showed that all glass-ceramic samples contained main crystals of perovskite, diopside and gehlenite and had a qualified mechanical performance with compressive strength above 100 Mpa, which meets the requirement of Chinese national standard for natural granite stone. With increasing crystallization temperature, pore size decreased, while the size of the perovskite phase firstly decreased and then increased with decreasing crystallization temperature. Samples had an optimum crystallization temperature of 1215 °C, maximum grain size and a densified structure with minimal pore defect.

Mar 1, 2018