Search Documents

Builders have been very familiar with iron since ancient times, but because of its weathering characteristics it was relegated to use as a fastening material in unexposed places and bronze became the popular metal for exposed applications. It is of interest that iron nails buried deeply about A.D. 87 at a Roman fortress and carefully covered with clean beaten earth under conditions practically excluding oxygen were found to be almost unrusted 1870 years later. (1) Today, weathering steels, which contain less than 2% of alloying additions, can be used in exposed situations without protection and without experiencing continuous wastage. As we all know the steady access of atmospheric oxygen to the surface of plain steel causes continuous corrosion. Weathering steels, on the other hand, due to their alloying additions develop their own impervious surface layer which limits the access of atmospheric oxygen and effectively limits corrosion. Table 1 shows the chemical composition of a plain carbon steel and a typical weathering steel. Fig. 1 shows what we refer to as direct corrosion - time curves in which corrosion loss is plotted against time of exposure in an strial environment. The weathering steel has a high rate initially which then decreases steadily for about three years, as the stable rust film builds up. This is followed by a practically linear relation where the very low corrosion rate, according to one school (2), is due to a blocking of the rust pores by insoluble complex salts formed from interaction of the oxidation products of the separate alloying elements. The start of the linear region represents a total corrosion loss of only about 2 thousandths of an inch.

Jan 1, 1970

By P. B. Bucky

THE purpose of this paper is to present a scientific method for deter-mining the proper span and shape of roof for safe and economical mining; at present, these two vital factors wherever pillars are left to support the roof are determined by local practice or general experience. To develop the method described here, experimental laboratory work was done. The arch adopted was a segment of a circle, a flat roof being considered an arch with an infinite radius. Hitherto, arches have been used underground without the background of stress analysis that generally precedes arch construction on the surface. In many cases results have not been as expected, because of the lack of knowledge of the factors affecting its strength and behavior. A theoretical and experimental study of arches should furnish informa-tion that will make it possible to design safe and economical surface structures as well as underground openings. For example, on the subject of mine drifts and tunnels, the present idea is that arching their backs increases their strength; this paper will indicate that this is not always true, and if it can be shown that under certain conditions arching becomes unnecessary an economic saving will result. In room-and-pillar work a question may arise as to whether arching the roof and gobbing the excavated material will result in timber saving, and a decrease in the dan¬gers from falls of roof. It is to be distinctly understood that each mine must be treated as an individual problem, and that answers to these ques-tions and many others can now be found after experimental laboratory data have been obtained.

Jan 1, 1934

By H. M. Lawrence

The recovery of phosphate rack from the ores in the land-pebble district of Florida is a simple washing and screening operation. In the gashing plants coarse phosphate only is saved. Log-Washer overflows and screen-undersize products containing an appreciable content of fine phosphate are discarded. The phosphate grains in the material discharged to waste are generally finer in size than the mesh--14 to 20 mesh or 0.346 to 0.03 inch--of the finest screen in the washer. The operators state that the washers ordinarily recover from 50 to 60 per cent of the phosphate content of the matrix mined. Any increase that can be effected in the recovery of phosphate would be of advantage to the industry and would conserve the mineral resources of the country. In considering possible methods that might increase the recovery obtained in phosphate-washing plants the application of flotation, if it could be successfully developed, seemed to warrant investigation.

Jan 1, 1928

By S. Nowosad, O. Langefeld, A. Godge

Pumped storage power plants are one of the options to store the fluctuating production of electric energy from renewable sources in a sustainable manner and is able to provide Europe with the opportunity to overcome the effects of climate change. However, due to the extensive land use required when planning the water reservoirs, several projects have been declined after social conflicts raised, even in Germany. Nonetheless, after the flooding and drought periods in northern Germany, the catastrophic floods of July 2021 in south west Germany, the country’s need to decrease its dependency on import of gas and energy supply, and the energy transition goals set for 2030 and 2050, it has become clear that the implementation for water reservoirs must increase in the coming years, whether above ground or underground. Furthermore, not only Germany is interested in the use of underground cavities for water and energy storage, other European countries as Sweden are currently developing studies and solutions to bring this concept soon to reality in Europe. This article introduces the systematic approach for planning and designing large underground cavities for water reservoirs as a sustainable energy transition approach and a climate change response by showcasing the process of selection and results of the “Energy and Water Storage Harz” (EWAZ) research project. Additionally, the results of the evaluation of the effect of implementing the selected underground and surface infrastructure into the current water management system in the region is presented. Finally, the different possibilities evaluated for the underground cavities within the project and the technical challenges involved are be discussed.

Feb 1, 2023

By S Vianna

Mineralogical information obtained from plant surveys is subject to errors, both due to sampling and experiment. To reduce these errors, and to ensure that information is consistent, a data reconciliation model has been developed for mineralogical data. Its capability includes mass balancing size data, total assays, assays within size-classes and liberation data. Unlike any other mass balance package, this package also allows reconciliation of the complex mineralogical information. For example, particles cannot simply be treated as binary, but consist of combinations of many minerals. Hence the distribution of mineralogical information is multidimensional and the mineralogical distributions are referred to as multiphase. In this paper, the different levels of mass balancing are explained, including how to mass balance liberation data. Furthermore a new technique based on probability theory can be used to infer distributions even when there is insufficient information to perform a mass balance, and this technique is also explained. Results for various stages are given.

Jan 1, 2002

By B. Wilhelmi, W. H. Somerton

Simultaneous measurement of pore and elastic properties of socks under a wide range of triaxial stress conditions may be made with equipment and methods developed in this paper. Tests were run on three outcrop sandstones at several confining pressures and axial stresses up to approximately 80 percent of failure stress. The greater reduction in porosities and permeabilities occurred in the hydrostatic loading portion of the stress cycle, but substantial reductions in both properties did occur upon application of deviator (triaxial) stress. Triaxial elastic moduli were calculated from strain gauge measurements. Both Young's moduli and shear moduli were found to increase with increasing confining pressure. Poisson's ratios increased with axial stress but showed no consistent change with confining pressure. Only very general relations were observed between pore and elastic properties. The lesser decrease in porosity and permeability at higher stress values is related to increase in rigidity of rocks at higher stresses. INTRODUCTION Many investigators have studied the effects of hydrostatic stress on the properties and behavior of rocks. A few have studied the effects of triaxial stress fields on individual physical properties of rocks. To our knowledge no one has measured simultaneously pore and elastic properties of rocks under a wide range of triaxial stress conditions. This is the purpose of this work. Rocks exist in the subsurface under what Jaegerl refers to as "polyaxial" stress conditions (all principal stresses unequal). When two of the three principal stresses are equal, this is referred to as triaxial loading. The triaxial method of loading is most commonly used in modern testing work because experimental difficulties in measuring physical properties of rocks are greatly reduced over polyaxial testing. Although triaxial loading may not reproduce subsurface conditions precisely, subsurface stress conditions are never known precisely anyway. Triaxial testing would seem to be more realistic than testing under hydrostatic loading (all principal stresses equal) for application of results to subsurface problems. The objectives of this work were threefold: (1) to develop methods of measuring simultaneously pore and elastic properties of rocks under triaxial stress conditions, (2) to determine whether changes in these properties are of sufficient magnitude to be considered in subsurface calculations and (3) to attempt to relate changes in pore properties and elastic properties since they will have been measured at the same time under identical loading conditions. REVIEW OF EARLIER WORK PORE PROPERTIES Several investigators have studied the effects of stress on the physical properties of rocks. Fatt and Davis2 showed the reduction of permeability of rock with hydrostatic loading. McLatchie et al.3 and Knutson and Bohor4 related permeability reduction to compessibility of reservoir rock, again under hydrostatic loading. Wble,5 and later Redmond,6 evaluated the effects of applied radial pressure on conductivity, porosity and permeability of sandstones. In this latter work, no axial stress was applied. Dobrynin7 reviewed much of the previous work done . on the effects of overburden pressure on physical properties of rocks. He concluded that changes in physical properties are controlled to a large extent by pore compressibility of the rock. Several sets of curves developed from empirical relations are presented. These curves permit estimation of change of properties with net overburden pressure, knowing the pore compressibility and porosity of the rock. Net overburden pressure is defined as (Pe - 0.85 Pi ) where Pe is the

By Michael J. Bailey, Peter M. Douglass

INTRODUCTION Spoil pile slope failures can have costly consequences. In- stability in the form of a single major event or as a recurring problem can 'mean lost production, lost resources and damaged mining equipment. In extreme but not uncomnon cases, a major spoils slide can force the closure and abandonment of a pit. Slope stability is affected by mine operating practices as we1 l as geologic conditions and material parameters. Mine operators can enhance spoil pile stability through constructive changes in their operations. Attention to the causes of in- stability can lead to development of operating practices tailored to site specific problems. Action aimed at limiting future instability is frequently more cost effective than continually "coping" with unstable spoils. The effect of mine operations on material properties is often overlooked because the "data" are not easily quantified nor input directly into stability analysis equations. We have found, however, that miners' experience with their own operation, as well as data pooled from similar operations, yields relation- ships which can be utilized to solve stability problems. The repetitive nature of area type surface coal mines with successive spoil pile rows further enables the development of useful site specific relationships. Stability problems can be mitigated by applying these relationships.

Jan 1, 1983

By S. M. Moos, R. E. Dugger

In reviewing available vacuum filtration equipment in this paper, several types of filters have been included which are probably not familiar to operators in the mining industry. However, it was felt that these units might be of interest in the event that an application should arise for the filtration of a product in the future that does not exist today. In addition, exposure of our industry to equipment used in other industries might have a tendency to be thought provoking and perhaps lead to the development of equipment and/or applications in our industry which do not necessarily exist at this time. Most innovations in filtration equipment have been confined to the improvement or design change of components and accessories, particularly reflecting the availability of materials of construction that have been developed. Recent developments in the application of horizontal belt filters have been innovative. The application of this unit as a substitute for or an adjunct to thickeners in a CCD circuit can certainly be innovative and perhaps provide a basis for reduction in capital and operating costs in this area. For example, mill tails are generally pumped at the highest possible density that will adequately flow. Tailings ponds and dams with their attendant design requirements are based upon this estimated water volume. Availability of a much dryer, non-flowing filter cake opens up several new options for disposal. Considerable cost savings could result in the design and planning of disposal areas for containing dryer material. No attempt has been made in this paper to provide a manual for the operation of all of the many types of equipment that are available. Rather, the paper tries to present an overview. Fundamentals of Vacuum Filtration Filtration may be defined as the separation of solids from a liquid effected by passing the liquids through a porous medium. If the filtrate is induced to flow through the medium by hydrostatic head, we refer to it as gravity filtration. If we utilize super-atmospheric pressure upstream of the medium we call it pressure filtration and if sub-atmospheric pressure is applied downstream of the medium we call it vacuum filtration. Centrifugal filtration occurs when a centrifugal force is applied across the medium. Centrifuges will not be discussed in this paper. The process goal of filtration may be the production of dry solids where the cake is the valuable product, clarified liquid

Jan 1, 1980

By R. A. Morse, W. W. Owens, D. R. Parrish, T. M. Geffen

Laboratory studies of several factors affecting measurements of relative permeability were made using the three-section plastic-covered core technique. Results show that the core assembly, properly constructed, will perform as a single unit, and that the testing technique will, under suitable conditions of pressure gradient, gas expansion, and migration of partial water saturation, permit measurement of flow characteristics not affected by technique. Wettability equilibrium is readily established in cores exhibiting strong wetting preference to water or oil when initially saturated with water. Laboratory tests must be conducted so that saturation changes represent those that occur in the reservoir. Immediate implications of saturation history are (1:) that the possibility exists of increasing the displacement efficiency of solution gas drive reservoirs over the natural process, and (2) residual gas saturations following water flooding in gas or gas condensate reservoirs will be 15 to 50 per cent pore space rather than 1 to 11 per cent as generally believed. INTRODUCTION Solutions of petroleum reservoir problems pertaining to production performance require the use of true relative permeability characteristics. 'This relationship of fluid conductivity and saturation has been obtained by reservoir engineers in four ways, namely: 1. From past gross reservoir performance and the extrapolation of this data based on experience,1,2 2. By using published fluid flow relationships obtained in laboratory studies on general type porous materials,3, 4, 5 3. By attempting a mathematical derivation of flow behavior," using some experimentally obtained characteristics of reservoir rocks, and 4. By laboratory flow tests using representative rock samples of a reservoir. The first three methods listed above have shortcomings which make their use limited or questionable. Production characteristics of only certain processes are obtained from field data and these are not available at the beginning of a reservoir's producing life, at which time they are desirable. It is fortuitous if general fluid flow characteristics obtained experimentally have accurate application to specific field problems. Also, it is felt that at this time there is not sufficient knowledge of the flow behavior of oil, water, and gas in porous materials to enable applicable analytical description of this to be made based on other measured rock characteristics. Measurement of relative permeability in the laboratory offers the only direct method subject to adequate checking for determination of flow characteristics applicable to field problems. Primarily, this paper deals with laboratory experiments to establish the effects of several factors on the measurement of relative permeability and the practical significance of this knowledge. Laboratory flow tests are essentially model studies; the gross reservoir being represented by a small rock sample. It is necessary to simulate in experiments all the factors of importance which influence flow in the reservoir, as well a.; to eliminate effects peculiar to the model studied to assure measurement of valid flow behavior. Factors which affect the measurement and behavior of fluid flow in porous materials have been studied by other investigators.3,7,8,9,10,11 This analysis is not intended to evaluate fully all factors involved, but to establish first the validity of measurements by the technique used and then study flow behavior under various conditions. The studies reported are as follows: 1. Effects of pressure gradient, 2. Effects of gas expansion in tests conducted at near atmospheric pressure, 3. Effects of migration of a partial water saturation in oil-gas-water systems, 4. Effects If wettability characteristics of the system. and 5. Effects of the fluid saturation history. The first three are important only in laboratory measure-

Jan 1, 1951

By D. R. Parrish, T. M. Geffen, R. A. Morse, W. W. Owens

Laboratory studies of several factors affecting measurements of relative permeability were made using the three-section plastic-covered core technique. Results show that the core assembly, properly constructed, will perform as a single unit, and that the testing technique will, under suitable conditions of pressure gradient, gas expansion, and migration of partial water saturation, permit measurement of flow characteristics not affected by technique. Wettability equilibrium is readily established in cores exhibiting strong wetting preference to water or oil when initially saturated with water. Laboratory tests must be conducted so that saturation changes represent those that occur in the reservoir. Immediate implications of saturation history are (1:) that the possibility exists of increasing the displacement efficiency of solution gas drive reservoirs over the natural process, and (2) residual gas saturations following water flooding in gas or gas condensate reservoirs will be 15 to 50 per cent pore space rather than 1 to 11 per cent as generally believed. INTRODUCTION Solutions of petroleum reservoir problems pertaining to production performance require the use of true relative permeability characteristics. 'This relationship of fluid conductivity and saturation has been obtained by reservoir engineers in four ways, namely: 1. From past gross reservoir performance and the extrapolation of this data based on experience,1,2 2. By using published fluid flow relationships obtained in laboratory studies on general type porous materials,3, 4, 5 3. By attempting a mathematical derivation of flow behavior," using some experimentally obtained characteristics of reservoir rocks, and 4. By laboratory flow tests using representative rock samples of a reservoir. The first three methods listed above have shortcomings which make their use limited or questionable. Production characteristics of only certain processes are obtained from field data and these are not available at the beginning of a reservoir's producing life, at which time they are desirable. It is fortuitous if general fluid flow characteristics obtained experimentally have accurate application to specific field problems. Also, it is felt that at this time there is not sufficient knowledge of the flow behavior of oil, water, and gas in porous materials to enable applicable analytical description of this to be made based on other measured rock characteristics. Measurement of relative permeability in the laboratory offers the only direct method subject to adequate checking for determination of flow characteristics applicable to field problems. Primarily, this paper deals with laboratory experiments to establish the effects of several factors on the measurement of relative permeability and the practical significance of this knowledge. Laboratory flow tests are essentially model studies; the gross reservoir being represented by a small rock sample. It is necessary to simulate in experiments all the factors of importance which influence flow in the reservoir, as well a.; to eliminate effects peculiar to the model studied to assure measurement of valid flow behavior. Factors which affect the measurement and behavior of fluid flow in porous materials have been studied by other investigators.3,7,8,9,10,11 This analysis is not intended to evaluate fully all factors involved, but to establish first the validity of measurements by the technique used and then study flow behavior under various conditions. The studies reported are as follows: 1. Effects of pressure gradient, 2. Effects of gas expansion in tests conducted at near atmospheric pressure, 3. Effects of migration of a partial water saturation in oil-gas-water systems, 4. Effects If wettability characteristics of the system. and 5. Effects of the fluid saturation history. The first three are important only in laboratory measure-

Jan 1, 1951

Reduce the hazards to which mine personnel are exposed by providing safer procedures for removing dragline wire rope terminations. Background The termination points of wire ropes used on draglines consist of a wedge and socket that lock the rope in place through friction. These components must be separated when the wire rope is changed. At present, the cannon method is the most common procedure used to accomplish this. However this method, using a small cannon and primer (detonator) cord to propel a steel projectile that will knock the wedge out of the socket, has the potential of causing injuries to mine personnel and damage to equipment. The Bureau of Mines, has devised safer, and equally efficient methods of removing wire rope terminations. The Bureau began by studying the cannon method, its merits and draw-backs. Safety guidelines were then developed for the cannon method, and two alternative methods-the pendulum ram and hydraulic pusher-were devised and tested. The Cannon Method The steel projectile used to separate the wedge and socket in the cannon method was found to be very effective. However, the method poses the inherent hazards of any explosive de-vice-hazards that could be increased by lax work procedures. There is no strict uniformity in the manufacture of the cannon or in the work procedures used in the mines employing it. Hazards could be reduced, or even eliminated, with adaption of certain manufacturing and work-procedure guidelines, such as 1) making the cannon and projectile de-signs, as well the work procedures used, uniform, 2) ensuring separate loading of the charge and detonator with insertion of the detonator through a separate port, 3) connecting electrical firing circuits only after the charge and projectile are loaded and the cannon is placed in its final firing position, 4) using approved detonating devices, 5) anchoring the cannon before firing and, 6) placing armor netting over the cannon before detonation.

Jan 1, 1986

By D. W. Park

Longwall Strata Control and Maintenance System (LoSCoMS) is a software and data communication system developed at the University of Alabama. This system integrates real-time shield monitoring, data presentation, analysis and forecasting of forthcoming events. The main objective of this system is to provide stability information on longwall panels including excessive shield load, low setting pressure, leg leakage and poor shield performance, eminent maintenance problems, etc. Analyses of various mining and geological parameters were also performed to determine past and present roof characteristics and to forecast roof loading patterns for the following mining cycles, next periodic weighting, etc. A local coal mine in the Warrior Coal Basin has adopted this system to provide daily evaluation of ground stability and maintenance problems of their longwall panels. Two years of experience with this system is covered in this paper.

Jan 1, 1998

The resistance of lead to chemical attack and the ease of its fabrication has made it one of the most useful of the metals available to the chemical engineer and the electrometallurgist. It has proved to be of particular value in the manufacture of sulphuric acid, and since the conversion of the sulphur of pyritic ores into sulphuric acid is becoming the duty of the metallurgist, the corrosion resistance of this metal will be a matter of considerable interest to him from the standpoints of both producer and user. He realises that there is little to be gained in carrying the process of purification past the ordinary economic limit if little or nothing is to be added to its corrosion resistance, and he as user would not be willing to pay a premium for such purification if it can be shown that its reputed value has no scientific foundation.The metallurgist is well acquainted with the trouble and expense of meeting demands which have nothing torecommend them but prejudice and fancy. The valuable anti-corrosive properties of lead are very commonly ascribed to its forming insoluble compounds with the acids sulphuric, hydrochloric, carbonic, etc. If we trusted superficial visual evidence alone, such a view would receive strong support, but in the light of what we know of the mechanism of corrosion we must attribute its resistance to other factors much less obvious to casual inspection. Certainly there may be some mechanical obstruction set up to diffusion of the liquids towards the surface of the metal.

Jan 1, 1932

By C. B. Manula, R. L. Sanford, R. A. Rivell

The need for a large capacity, high speed computer is more apparent in the revised model than in the original one. Core storage requirements for data and model logic have at least tripled. This dictates the use of one of the large modern machines such as the IBM 360-370 series or the Univac 1108 and 1110, which handle the model without the need for extensive program overlay. Computer time is expensive on these machines, however, and comprehensive analysis has gone into optimizing computer execution time consistent with model information flow sensitivity. For example, revised locomotive tramming routines have been developed which will significantly cut execution time compared to the previous version. Transceiver Applications The computer coding for the model has been developed to enable program execution and testing using a remote terminal on a time sharing system. In fact, nearly all of the coding, debugging, testing and modifications have been performed from a terminal during develop¬ment. The gaming options described in the Model Input Section of this report have been designed so that they are easily changed by the user from any remote site. One restriction on remote applications which could arise, however, is where highly detailed output options are specified, resulting in a large amount of output records which could be handled more efficiently on a high speed printer.

Jan 1, 1974

By Nina I. Fedunec, Olga E. Fomicheva

Results of researches on creation of the intelligent adviser system for mining dispatcher are represented. A method of the analysis of subject domain is considered and results as the generalized expert questionnaire and diagrams are represented. The system-adviser REALTREE, functioning in real time, is represented, results of an estimation of a system effectiveness during decision making by the dispatcher are submitted.

Jan 1, 1996

By F. G. Robb, D. N. Madge

This paper details some of the specifications and problems associated with implementing on-line control of a potash concentrator. The computer system described has the capability of three levels of control, including DDC with a single central processor. The system is also capable of on-line program compilation and modification through an extension of vendor utilities. The system is now in operation.

Jan 1, 1969

By Robert S. Mayo

My subject today is "Drilling-and-Blasting of Small Rock Tunnels". I am sure that there will be some people, primarily college students but perhaps Consulting Engineers, who will say: "Drilling-and-Blasting? I thought that went out with the invention of the Tunnel Boring Machine". A few years ago I talked to Dick Robbins and he told me that they did not try to sell a "Robbin's Mole" unless the tunnel was two miles long. For easy calculations I use 10,000-ft. (3km) A Mole today costs about $2 million which works out to $200 per lineal foot. This is "front money". You cannot place the order unless you are the uncontested low-bidder and then you must wait at least six months for delivery. Of course you can use that time to square up your portals, ready to turn-the-eye, or maybe you have shafts to sink to reach the tunnel grade. But this is "dead-time" and it is a heck of a feeling to have a job and cannot get started on it until you get the Mole. I do not have the American figures on lengths of tunnels but there was an article a few years ago in a British magazine: NEW CIVIL ENGINEER, on this subject. This stated that 75% of the jobs in Britain which were bid were for small tunnels, 10-ft x 10-ft (3m x 3m) or smaller, and that they were less than 5,000-ft (1.5km) in length. This does not mean that 75% of the footage in Britain was less than 10-ft in diameter. It means that 75% of the jobs being bid were less than a mile in length. From my experience in the U.S. I believe that we have substantially the same ratio: so many of the jobs with which I was associated were short, 1,000-ft, 2,000-ft and sometimes 3,000-ft and the bores

Jan 1, 1981

By M. W. Grodner, J. Maaren, G. Guler, J. K. Schweitzer

The selection of the most suitable mechanized mining strategy has to consider the geotechnical environment in which it will be operating. A mechanized mining method or machine is designed to a given set of specifications to work within an environment. The geological conditions that define this environment are fixed—detailed information of these conditions for design specifications is thus critical. Two major classes of geotechnical parameters are defined—critical and design. The critical controlling factors are a result of mineral composition, size, shape, abundance, assemblage and associated texture, as well as discontinuity type and orientation. Design parameters are specific to each deposit, and their nature cannot be broadly described, as with the critical factors. It is shown that for major deposits in South Africa, namely the Witwatersrand Basin (gold), the Bushveld Igneous Complex (PGEs) and the Karoo Coalfields that by incorporating geological and geotechnical information that appropriate mechanized mining methods can be deduced, and that the performance and design parameters of specific technologies can be determined

Sep 1, 2001

By J. Beddoes

The various microstructural factors that influence the creep resistance of y-titanium aluminides are presented and discussed. Titanium aluminides have potential for a variety of intermediate temperature applications in both gas turbine and reciprocating engines. While it is well established that the 'fully lamellar' titanium aluminide microstructure offers superior creep properties, the particular influence of lamellar morphology, third phase precipitation, and grain boundary structure in controlling both the primary and tertiary creep behaviour is presented. The results are primarily based on tensile creep experiments undertaken using several titanium aluminide intermetallic compositions processed via powder metallurgical techniques, investment casting and Bridgman directional solidification. The results indicate that lamellar structure and precipitate formation have a major impact on primary creep, while microstructural degradation through both lamellar and precipitate coarsening influence on the onset of tertiary creep leading to fracture. The results are used to design a creep resistant microstructure produced by directional solidification and the effectiveness of this designed microstructure is demonstrated through 10,000 hour creep tests.

Jan 1, 2004

By Caitlyn J. McKinley, Ahmad Ghahreman, Maziar E. Sauber

Ever-growing global needs for critical metals, such as rare earth elements (REE), and base metals, such as copper and nickel, and their environmental impact motivated the pursuit of sustainable flowsheets. Regeneration of hydrochloric acid in chloride-based leaching flowsheets as a critical unit operation is an example of such endeavours. This study presents an efficient hydrochloric acid regeneration method from a magnesium chloride solution waste by addition of sulphuric acid in relatively low temperatures. The effects of temperature, initial magnesium chloride concentration, amount of sulphuric acid added, and airflow are examined. Experimental work are focused on temperatures between 80 and 95°C, initial magnesium chloride concentrations of 2 to 5 M, 100% to 220% stoichiometric sulphuric acid additions, and airflows between 200 to 600 mL/min. The developed technology recovers hydrochloric acid at a high rate and concentration with a relatively small environmental footprint. INTRODUCTION The mining and metals sector is under increasing environmental and economic pressure to make more efficient use of chemical reagents and energy in the production process. This affects several areas of process and flowsheet design such as the selection of the most appropriate unit operations and the overall design of the process steps paying heed to sustainability. Owing to the inherent inefficiencies of physical and chemical processes used in the mining industry, there will be materials and streams generated that are not a desirable part of the envisaged flowsheet. Thus, methods are implemented to recover and recycle such effluents. If the recovery and recycling are not economical, then procedures are followed to neutralize and dispose these effluents. In many cases, these effluents are potential contaminants or hazardous materials, and their disposal should be looked at in a much larger context. The safe management of the contaminants and hazardous effluents is a daunting problem in the mining industry and is fraught with technological, economic, social, and political challenges.

Jan 1, 2019