Search Documents

By A. T. Schwennesen

Every engineer has occasion to trace or copy a map, plan, or other drawing on paper too thick for the ordinary way of using tracing-cloth or tracing-paper. When the figure is small and simple a copy may be made by holding the original against a window-pane, coverin& it with the paper, and tracing direct by the aid of the strong sunlight from outside. The need of utilizing this principle on a larger scale and in a more convenient position led Dr. J. C. Branner to plan the table of which the following is a description : This table was first made in the form of an adjustable glass-top table with a mirror beneath, in 1887, while Dr. Branner was State Geologist of Arkansas. Later it was modified as experience suggested until the form as here described was evolved. The device consists essentially of a drafting-table with a plate-glass top, upon which the original drawing and the paper are laid, and a mirror mounted underneath to reflect the light of the sky up through the drawing. The glass top is hinged and fitted with two arms and thumb-screws, so that it can be raised and fixed to any position, either inclined or horizontal. The mirror is pivoted and revolves about a horizontal axis, so that it may be tilted to any angle. The hood of cardboard or black cloth prevents the reflection of light from the tracing, and may or may not be attached to the table.

Jan 1, 1912

By Mark A. Anderson

INTRODUCTION The accomplishment of a well engineered design, and the realization of efficient plant operation cannot be achieved without weaving a web of safety consciousness from the beginning of the project. When the plant becomes operational, and throughout its life, responsibility safety will rest with the client or operator. Recognition of this understanding does not reduce the importance of the engineering and construction contractor's role, but merely puts the responsibility where it belongs. A project which has had little or no operator input during the early stages of design is almost certain to have serious work place safety, health, and environmental problems in spite of the fact that all MSHA and OSHA design requirements were met and the engineering was performed using accepted practices. DEFINITIONS The author has a personal preference in safety definitions that begins and ends with simplicity. If the safety criteria, program, and rules are confusing or complex, the results will soon become obvious. Confusing and complex are the key elements in the avoidance of responsibility and if punitive is added to the list, a brew exists which breeds accidents, illness, and poor performance. A safely designed and operated plant is one that a worker can journey to each day; leaving that person and his or her family with the above average expectation that the person will return healthy, emotionally intact, and hopefully a little wealthier. If the objective or results of a planned or existing safety program don't fit the definition. then the reader is probably contemplating a very sophisticated

Jan 1, 1986

By A. Vasebi, É. Poulin, A. Desbiens, D. Hodouin

Maximizing benefits generated by separation plants in the mineral processing industry is of prime importance. To achieve this goal, observers and controllers are both key tools playing a crucial role for economic optimization. Although these methods have been widely discussed in the literature and that numerous applications have been reported, coupling the different algorithms raises practical challenges. The economic function definition, the selection of the real-time optimization structure, the elaboration of observer and controller models, the controller development, and the tuning of stochastic and deterministic parameters strongly influence economic performances. The objective of the paper is to discuss the major difficulties related to the implementation of a real-time optimization system and highlight the benefits of linking data reconciliation and model predictive control for a simulated flotation plant. A systematic topdown approach is used to go through the main design phases and to comment on the different options available for the development of the optimization structure. An internal model predictive controller coupled with a stationary observer is applied for the direct optimization of a three-stage flotation plant simulator based on a phenomenological model. The results show performance improvements in terms of increased revenues brought by reduced grade variability and collector consumption. The discussion also proposes alternative avenues that could be taken to achieve comparable improvements. Finally, since the limited simulated case-study cannot provide a complete understanding of the benefits brought by a data reconciliation observer, recommendations for industrial applications, which are more complex, are provided to promote effective implementations.

Jan 1, 2016

By Arnaud Faucher, Amar Sabih, Sudarshan Martins, Tristan Martin, Sami Makni, Peter Radziszewski, Poorya Hosseini, Francois-Raymond Boyer

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012

By A. Phillips, H. J. Fisher

The influence of temperature and composition on the viscosity of high-purity liquid metals and alloys of the Pb-Sn and Sb-Cd systems was investigated by the logarithmic-decrement method. The variation of viscosity with temperature above the liquidus followed the equation: n = AeE/RT No large increase in viscosity was found just before normal freezing of any of the metals or alloys investigated. Certain alloys, supercooled below their stable liquidus, however, did show a marked increase in viscosity. Experimental activation energies for viscosity were determined for the metals investigated. Liquid-metal density values were obtained by a modified Joeger's method. IK an investigation of the properties of molten metals, the study of viscosity as a suitable means for studying the physical nature of the metallic liquid state has been utilized. Although interest in the relationship of the liquid to the solid-metal state holds promise of broadening the knowledge of metals in general, much information that is available regarding the influence of temperature and composition on viscosity, especially near the freezing point, is still controversial. The purpose of this paper is to present the results of recent work on this subject. Although interest in factors influencing the fluid behavior of metals and alloys has arisen from theoretical as well as applied studies of liquid-metal properties, the development of a comprehensive theory of the mechanism of viscosity has been handicapped because so little is known about the liquid state. Several theories of viscosity have been proposed and among the more recent are those of Andrade,1 Bernal,2 Frenkel,3 Eyring,4 and Gutmann and Simmons.5 Athough these contributions have helped to establish a basis of approach for studying the nature of viscosity, the fundamental aspects of the variation of viscosity with alloy composition have, in general, been neglected. Experimental Metals and Alloys Investigated: The Pb-Sn and Sb-Cd alloy systems were selected for investigation because they form constitutional features of theo-

Jan 1, 1955

By Yanis Miezitis, Gerald Mueller, Timothy F. McConachy, Ronald G. Sait, Keith R. Porritt, William J. McKay

In November 2004, Australia lodged with the United Nations Commission on the Limits of the Continental Shelf possible new maritime boundaries in relation to Australia’s continental shelf extending beyond 200 nautical miles from the Territorial Sea Baseline (Colwell and Symonds, 2005). If agreed by the commission, just over half of Australia’s land mass will lie below the sea, and Australia will have one of the largest marine jurisdictions in the world (14.41 million km2). With this jurisdiction comes a responsibility to manage and sustain the marine environment (McConachy, 2006). Knowledge of minerals and their resource potential is part of this responsibility but is generally poorly known (McConachy, 2005).

Aug 24, 2006

By Frederik P. Agterberg

This paper deals with frequency distributions in the field of mineral resource evaluation when a grid is superimposed on the study area and metallogenetically significant attributes are coded with respect to the cells of the grid. It is shown that the parameters of a negative binomial distribution for frequency of mineral deposits per cell can be derived from the parameters of a gamma distribution for the coded attributes. It is also shown that an exponential model for spatial correlation of cell values and Matheron's discrete Gaussian model for indirect transfer functions may provide a suitable methodology for relating cell value distribution to cell size.

Jan 1, 1977

By W. J. Pennstrom, J. R. Arnold

This paper focuses on solution-balance management around heap-leach operations. Experience has shown that increased leach recoveries can be achieved by utilizing various leach-solution recirculation techniques. The most prominent solution-recirculation technique is intermediate leaching. The net effect of intermediate leaching is to increase recovery plant performance by increasing solution concentration tenors, to increase metal recovery by increasing the total leach time and to decrease the overall capital expenditures required for metal-recovery facilities. The adverse effect on the flow of cash from increased metal inventories in the recirculating solutions is offset by increased metal recovery and lower operating costs per unit produced.

Jan 1, 2000

By C. B. Barlow, T. A. Mekelburg

Due to a tight ash constraint on the clean coal product and difficult middlings washability characteristics, a considerable amount of coal was being lost in the jig middlings at the Monterey No. 2 Mine. An investigation was conducted into circuitry to recover this lost coal with minimal effect on the total clean coal ash. A reverse two-stage hydrocyclone system cleaning at low specific gravities was selected. This system is currently recovering approximately 5.8 kg/s (23 stph) of 11.5% to 12.5% ash coal. The specific gravity of separation for the system is about 1.5 and the probable error is 0.13.

Jan 1, 1986

By Venugopal B, M Kumaran, Thomas John, Vetriselvan A

The initial pile load tests are conducted to ensure the geotechnical capacity of the pile in a particular site condition. Normally kentledge method is adopted for the compression pile load tests. In this method the entire kentledge load is loaded above secondary beams which are supported by concrete blocks above the Natural Ground Level. So, it is important to ensure the SBC (for shear and settlement) of the natural ground. In one of our projects initially it was decided to go with kentledge system for initial compression load test on 56m long 1200mm diameter BCIS pile. The test load and total kentledge load were 2160t and 2700t, respectively. The soil strata mainly consisted of clay with low SPT N value and water table almost at ground level. It was suggested to replace top soil using Granular Sub-base (GSB) with good compaction in order to avoid excessive settlement of concrete blocks placed to support the kentledge weight. When the kentledge loading started, even before reaching 10% of total kentledge load, excessive settlement on the GSB layer was observed. This paper describes the problems faced during normal kentledge method and how it was overcome using the liner pile system for initial compression load tests in this particular site condition for higher test load.

Nov 1, 2022

By Cheong-Kee Park

Since 1983, Korea Ocean Research and Development Institute (KORDI) have performed surveys on deep-sea mineral deposits in various areas with respects to their occurrences in Pacific ocean including manganese nodules in the C-C area of Northeast Pacific, Co-rich manganese crusts in various seamounts of West Pacific and hydrothermal sulfide deposits in back arc basins of Southwest Pacific. Among the results of these activities of KORDI, remarkable things were the registration as a pioneer investor in 1994 through the Government of Korea and the accomplishment of relinquishment on the allocated area in 2002 according to the relevant regulations. KORDI is faced to handle detailed surveys to select the optimum mining sites in the allocated area of 75,000 km2 and environmental studies to meet the requirements of the regulations or recommendations of the ISA. In respects of future exploration strategies, it is considered that methods and tools of previous exploration activities should be changed to the highly advanced technology. Establishment of an advanced exploration system and actual practice in appropriate areas become one of important tasks of KORDI in exploring deep-sea minerals, particularly manganese nodules. A technical strategy for future detailed surveys in the allocated area is realization of simultaneous and precise data acquisition on bottom information, such as variations of microtopography, nodule distribution, and transparent layer thickness of sediments in relatively small area (10 km x 10 km) representing certain specific regions, by high resolution survey technology. It would be not only a challenge for new exploration system in deep-sea environment, but also a mission for deep seabed mining venture.

Jan 1, 2003

By W. L. Falke, A. A. Cochran

Vast deposits of low-grade manganese ore exist in the United States, yet domestic production is insignificant compared to the more than 2 million tons of ore imported yearly into this country.1 A basic problem in connection with manganese is to find economical ways to utilize domestic resources.2 As a part of its program to conserve domestic mineral resources and to reduce dependence on foreign sources, the U.S. Bureau of Mines has conducted extensive research to broaden manganese technology and to find economical processes for recovering manganese from these low-grade resources. Although a great many processes have been proposed for treating domestic manganese resources, a failing of many of them is that too many steps are involved for economical operation.2 Some of the major processes that have been proposed were reviewed by Norman and Kirby.3,4

Jan 3, 1967

By R. E. Lindstrom

Effective separation of rare-earth mixtures is obtained using hydrogen as a retaining ion at 200° F with ethylenediaminetetraacetic acid (EDTA) eluant. Results obtained in Bureau of Mines bench-scale apparatus and large columns with hydrogen as a retaining ion closely parallel those obtained with copper as a retaining ion. The use of hydrogen as a retaining ion permits EDTA and water, collected before rare-earth breakthrough, to be recovered in a form that allows the material to be recycled without extensive processing. With the exception of yttrium and dysprosium, separation of rare-earth mixtures is improved and throughput is increased by elevated temperatures. Separation with 1,2-diaminocyclohexanetetraacetic acid (DCTA) eluant increases markedly on increasing temperature from ambient to 250° F; however, on the basis of separation efficiency, DCTA does not compare favorably with EDTA.

Jan 1, 1962

By Saied S. Navid, Michael A. Piepenburg, Richard F. Escandon, Robert C. Lindsay

INTRODUCTION Phase I of the Los Angeles Metro Rail Project, known as MOS-1 (Minimum Operable Segment-1), is the first phase of the 27 km± (17 mi) subway starter line. MOS-1 is currently under construction and involves approximately 6.4 km (4.4 mi) of subway, five stations, yards and shops routed through the downtown area of Los Angeles. The project will form the initial heavy rail backbone of a more extensive light and heavy rail transit system planned for the greater Los Angeles area in the future. Construction Contract A-171 is one of 4 tunnel contracts within MOS-1 and involves construction of twin tunnels running from the downtown metropolitan area west to MacArthur Park. The heavily populated and developed downtown area, potentially gassy ground conditions, and the possibility of undocumented abandoned oil wells in seismically active southern California made the design and construction of Contract A-171 a uniquely interesting project. This paper summarizes the construction history to date (December, 1988) including design geotechnical considerations, tunnel support design, as-built geologic conditions, shield tunneling performance through soft ground, and ground response. The findings presented herein may aid in the design and construction

Jan 1, 1989

By I. E. Lane

Conventional demand management techniques invariably fail to offer optimum control flexibility in an operationally complex gold mining environment. An improved control system for electrical demand management is proposed. The system is designed to provide more effective load scheduling and control strategies by means of a computer aided demand management system (CADMS). The objective of the CADMS is to provide a responsive computational aid and adaptive control system for effective demand management. The system consists of a short term load forecasting module, an interactive load scheduling module, an incentive based electricity cost allocation module and a power management information module.

Jan 1, 1987

By B. Day, L. Elinson

There is general agreement among those involved in occupational and public health that work-related diseases are under-diagnosed and under-reported. Highmark is particularly well positioned to carry out industry health analysis as it provides medical insurance for approximately three quarters of the insured population of Western Pennsylvania including some of the areas largest employers. The purpose of this study is to gain a more accurate understanding of the mining industry rates of respiratory diseases that maybe occupationally related and identify those inflated respiratory disease and hearing loss rates. Conditions examined included COPD, asthma, and pneumoconiosis.

Jan 1, 2004

By N. O. Johnson, J. Boyer, D. H. Sargent, R. B. Frahme

Although the Western bentonite industry has grown rapidly, it is facing major challenges to sustained growth. The fundamental penalty of costly overland transportation to both domestic markets and to US seaports is of increasing importance; as both substitute materials and foreign bentonites present more formidable competition in the historic market areas of drilling muds, foundry sands, and iron ore pelletizing; and as foreign demand grows more rapidly than domestic demand. The Western bentonite industry is facing these challenges by altering its transportation patterns, by upgrading of products, and by emphasizing customer service and stringent quality control.

Jan 1, 1980

By N. O. Johnson, J. Boyer, D. H. Sargent, R. B. Frahme

Although the Western bentonite industry has grown rapidly, it is facing major challenges to sustained growth. The fundamental penalty of costly overland transportation to both domestic markets and to US seaports is of increasing importance; as both substitute materials and foreign bentonites present more formidable competition in the historic market areas of drilling muds, foundry sands, and iron ore pelletizing; and as foreign demand grows more rapidly than domestic demand. The Western bentonite industry is facing these challenges by altering its transportation patterns, by upgrading of products, and by emphasizing customer service and stringent quality control.

Jan 9, 1979

Pyrrhotite is the predominant gangue mineral at Renison comprising about 60 percent of the sulphides in an average ore blend. It exists as two crystal structures - monoclinic and hexagonal. Monoclinic pyrrhotite is the slowest floating of all minerals but is ferromagnetic and hence recoverable more efficiently by low intensity magnetic wet drum separators than flotation. This paper discusses the installation and commissioning of four 0.915 m x 3.0 m, 0.1 Tesla permanent magnet, wet drum separators prior to sulphide roughing flotation. Planned circuit and process control modifications to better accommodate magnetic separation into Renison's flowsheet will be Discussed.

Jan 1, 1991

Aluminum alloys are used in two broad classifications: wrought and cast. Wrought alloy products, which are formed into final shape by rolling, forging, extruding. etc., contain low percentages of alloying elements; whereas cast aluminum products, which generally are not worked before use, may contain higher percentages and a somewhat different selection of alloying elements. For example, wrought aluminum alloys usually contain less than one percent silicon and cast alloys contain as much as 18 per-cent silicon. While there are good techniques available for separating aluminum alloys from mixed scrap, there are no efficient ways to separate wrought aluminum from cast aluminum. The high levels of silicon, iron) copper, and zinc from the cast alloys make wrought-cast mixtures unacceptable for wrought alloy production. Consequently, separated wrought aluminum scrap commands a premium price on the market. Since increasing amounts of mixed aluminum alloys are being recovered from automobile scrap, this separation is important for efficient recycling of these alloys. Approach The difference in thermo-mechanical properties between the two classes of aluminum alloys is used as the basis for the separation process. Casting alloys lose their ductility within a certain temperature range while wrought alloys remain ductile. As temperature increases, aluminum alloys gradually become weaker, and at a certain temperature, each alloy loses strength and ductility due to incipient melting in localized areas. For casting alloys that temperature generally lies between 520° to 560° C, but it is above 600° C for most wrought alloys. Mild crushing, therefore, in the proper temperature range will result in complete fragmentation of the casting alloys but only plastic deformation of the wrought alloys. A simple screening step then is used to separate the oversize wrought pieces from the fragmented cast alloys.

Jan 1, 1984