Search Documents

By G. H. Schnakenberg Jr.

In response to the underground mining industry's growing concern with the exposure of workers to the diesel particulate matter (DPM) component of diesel exhaust, a method was developed to estimate the average workplace concentration of DPM that could be expected from using the new lower DPMemitting engines now being approved by the US Mine Safety and Health Administration (MSHA) when these new engines are equipped with state-of-the-art exhaustcontrol technology for filtering and combusting DPM. The resulting estimate uses the MSHA-reported particulate index for these engines, the prevailing rule-of-thumb ventilation rate of 150 cfm/hp and the available diesel-exhaust filter technology that has been shown to be at least 80% effective in reducing tailpipe DPM. In the estimate calculation, every engine used in an underground mine is assumed to be equipped with this control technology. Under the stated reasonable conditions, an average DPM level of 90 µg/m3 (mass) is predicted as technically feasible.

Jan 1, 2002

By A. T. Janssen

Production planning of direct-shipping ore from a number of relatively small deposits serves to sequence development and mining of these deposits so that both long- and short-range demand can be met while the timing of development cost is such that the average annual rate is minimized. Hand-computed methods have the disadvantage that they require substantial effort and time and cannot be exhaustive. The application of operations research and computers not only overcomes these disadvantages, but opens up additional applications, such as feasibility studies involving alternative mining strategies and changes in the ore market. The method employed concerns linear programming and specifically the Big-M algorithm applied to the variant on the simplex technique with penalties applied to deviations from the desired ore grade. Acceptable 20-year production schedules could be generated in relatively little time, i. e. , in less than 200 seconds for the central processor of the Control Data Corporation 6400 system of the University of Colorado in Boulder.

Jan 1, 1969

By H. Michael Breza

Texasgulf Inc. installed bucketwheel excavators and overland conveyor sysems at its Aurora, NC phosphate mine o increase the productivity and flexibilty of the surface mining operation. This ;ystem has significantly improved overrall. Its flexibility is evidenced by adapation to operation requirements, such is mining area moves, movement of xcavated overburden to designated ites, selective handling of overburden, poll placement contouring, and proiding an environmentally sound and afe operation. The system's productiv:y is evidenced by case studies relating. overall production, excavation rates nd cost-effectiveness. There are many competing alternaves available for excavating uncon)lidated overburden: truck-shovel, raglines, dredges and bucket wheel ticavators. These alternatives also may used in tandem to recover reserves icated at greater depths.

Jan 1, 1993

When underground extractions occur beneath or in close proximity to valleys and other forms of irregular surface topographic features, the observed vertical subsidence at the base of the valley is less than that would be expected in flat terrain, while the valley sides are observed to move inwards towards the centre of the valley. The reduction in subsidence at the bottom of the valley is referred to as upsidence and the convergence of two sides of the valley is termed valley closure. Research coupled with mining experience over the past few decades in Australia has identified valley closure subsidence as being very real and quite significant part of non-conventional subsidence effects, which always have adverse effects on natural features, with risks to water flow and aquatic ecosystems. In this paper, we describe a threedimensional numerical modelling approach to investigate the geomechanical mechanisms which cause the valley closure subsidence behaviour, using distinct element computer package 3DEC. The calibrated models can accurately predict subsidence and horizontal displacements, and they are subsequently extended to specifically study the effect of a series of mining geological and topographical factors on valley closure subsidence phenomenon, by developing a range of hypothetical scenarios. Previous analyses carried out using a two-dimensional numerical modelling technique have identified the potential parameters that affect the valley closure subsidence, which mainly include longwall position, horizontal stresses, valley sloping angle, and valley shape. Further three-dimensional analyses regarding the relationships between the major factors and valley closure subsidence are discussed in this paper. The results have significant implications with regard to both the underlying mechanisms that lead to this nonconventional subsidence behaviour, and how these should be incorporated in future valley closure subsidence prediction and mitigation of its impacts on natural features.

Jan 1, 2015

THE morning session on non-metallic minerals was opened briefly by the chairman, Oliver Bowles, giving the usual instructions and then turning immediately to the introduction of the speakers. "Min-ing and Preparation of the St. Peter Sandstone in' Arkansas" by D. D. Dunkin was first presented by W. M. Weigel, mining technologist for the Missouri Pacific R. R. The paper covered a discussion of the geology of the sandstone, correlating it with the sand-stones at Klondike, Mo., and at Ottawa, III. Its physical appearance, structural characteristics and thickness; the mining methods, blasting, loading, haulage and classification were taken up. A series of slides aided in clarifying the details. The discussion consisted of questioning Mr. Weigel on operating details. The second paper, "Geology and Mining of Diaspore and Flint Fire-Clays of Missouri," written by H. S. McQueen, geologist with the Missouri Bureau of Geology and Mines, and C. R. Forbes, professor of mining, Missouri School of Mines and Metallurgy, was presented by Mr. Forbes. It thoroughly covered the geology, stressing the peculiar sink formations in which all diaspore clay deposits of the region occur. The crudeness of the mining methods was mentioned and believed justifiable because of the small size of the indi-vidual deposits. It was stated that the diaspore and flint clay deposits of Missouri were confined to an area 60 mi. square and it was found in a survey that the average deposit had dimensions comparable to the fol-lowing: 100 ft. long, 75 ft. wide and 50 ft. deep. The largest deposit found was 800 ft. long. 500 ft. wide and 20 ft. deep. It is estimated that the known reserve of clays is from 750.000 to 1,500,000 tons. Mr. Forbes stressed the fact that in mining clays the major problem is entirely one of sorting. This is done under the supervision of a pit foreman trained to make this classification by eye. The mine-run clays are sepa-rated into diaspore clay ranging in alumina content from 70 to about 85 per cent, first grade Burly clay 00 to 70 per cent, and Flint clay 52 to 60 per cent. Discussion of the paper consisted in questioning Pro-fessor Forbes on labor. cost, haulage, drilling, and geology.

Jan 3, 1928

By Yuki Tsunazawa, Shuji Owada, Kazuki Tahara, Shinobu Ogino, Chiharu Tokoro

"Printed circuit boards (PCBs) are an important constituent of waste electric and electronic equipment (WEEE), and contain many electronic components with valuable, hazardous or both materials. Recycling of PCBs is an important subject not only from the treatment of waste but also from the recovery of valuable materials. Demand for rare earth metals is expected to accelerate because of their growing use in next generation high technologies. Since some of these metals are concentrated in a specific electronic component, for example, Ta in capacitors, a special and selective grinding such as parts detachment from the board is effective for the recycling of a part of rare metals. However, direct computer simulation method to investigate a comminution/detachment process of PCBs has not yet been established. In this study, our objective was revealing the mechanism of breakage phenomena in comminution / detachment process of PCBs using computer simulation. A special and selective grinding using an agitation mill promoted the removal of components from a PCB by detachment and was an effective method for the recovery of rare metals. Simulant PCBs on which some capacitors were solder-mounted were used for the comminution test using drum type mill with agitator. To describe this mechanism of the parts detachment process, a computer simulation using discrete element method (DEM) was conducted. Although only an indirect simulation using the spherical particle model was possible for part detachment and board breakage, the particle-based rigid body model could directly represent the behaviour of PCBs. Simulation results successfully corresponded to comminution experimental results."

Jan 1, 2014

By G. R. Frank, R. E. Willett, E. H. Hollingsworth

The most generally accepted equilibrium diagram for A1-Fe alloys has a eutectic system on the aluminum side with an essentially insoluble constituent of the formula, FeAl,, as the second phase. In 1938, Bradley and Taylor1 did report a phase change of FeAl,, but this change has never been confirmed. According to them, FeA1, is the stable phase only at higher temperatures; at lower temperatures, it is converted into Fe2Al7 and aluminum. It has now been found that there is, in fact, a phase change of the Al-Fe constituent on the aluminum side of the equilibrium diagram. This change, however, is not the one reported by Bradley and Taylor. The alloys used were cast by continuous processes and had these analyses: Fe - 1.98 to 2.02 pct, Cu-0.01 pct, Si - 0.01 pct, Mn - 0.01 pct, Mg - 0.00 pct, Zn - 0.00 to 0.01 pct, Cr - 0.00 pet, Ti - 0.00 to 0.04 pct. The constituent in these alloys was identified by X-ray analysis with a Guinier camera and by chemical and X-ray powder diffraction analyses. Two procedures were used to separate constituent for the last two analyses. In one procedure, it was separated by treating a sample with a solution of methanol saturated with iodine. And in the other procedure, it was separated by first applying, at 12 amp per sq ft in 15 pct sulfuric acid at 70°F, an oxide coating to a sample, and then dissolving this coating in a solution of 35 ml of 85 pct H3PO4 and 20 g of CrO3 per liter. Several observations directed attention to a phase change of the A1-Fe constituent. Differences that appeared too great to be accounted for by micro-structure alone were found in the voltages required to apply the same thickness of an oxide coating to products from rapidly and slowly chilled ingot. Even more striking was the difference in appearance of the coatings themselves. One applied to a product from a rapidly chilled ingot was dark gray in appearance, in fact, almost black, while one applied to a product from a slowly chilled ingot was essentially white. Also, even a short period of thermal treatment at an elevated temperature of products from rapidly chilled ingot led to the same anodizing behavior as that of products from slowly chilled in-

Jan 1, 1962

Willemite mineralization was discovered in 1966 in the North Flinders Ranges of South Australia, in the course of a stream sediment sampling programme. Further work outlined a total of nine separate willemite occurrences in the Copley/Beltana area, and ten small deposits in the Toondana area south of Parachilna. Mineable reserves of 1 000 000 tonnes grading 36.8% zinc were outlined in three deposits in the Copley/Beltana area and campaign mining of the Main Orebody commenced early in 1974. The main group of deposits all occurred within red, dolomitized Cambrian Ajax Limestone, and most are associated with significant thrust faulting. The area of the Main Orebody group of deposits has been intensely fractured, and the surrounding dolomites are often brecciated and contain up to 5% zinc. Lead and arsenic mineralization are minor components of the main group of deposits. Masses of Middle Proterozoic Willouran Formation crop out adjacent to or close to most of the deposits in the Copley/Beltana area. The Willouran is frequently highly sheared, brecciated, and often contains large inclusions of younger formations. It is believed that most of the Willouran outcrops represent piercement structures.

Jan 1, 1975

By Jaeheon Lee, Junmo Ahn, Jiajia Wu

In this project, low grade copper ore samples were obtained from two mining sites in the US, and they were chalcopyrite-rich (sample A) and conichalcite-rich (sample B) ore. Copper grades were 0.6% and 0.4% for the two samples, A and B, respectively. Leaching experiments were conducted by bottle roll tests for 24 hours, and various lixiviant systems were applied. Methanesulfonic acid (MSA) and glycine were used as alternative lixiviants to sulfuric acid. Oxidants including ferric ion and hydrogen peroxide were tested. The results showed the copper extraction of sample A increased after adding 1 g/L ferric ion in sulfuric acid and MSA solution, from 20% to 36%, but further increase was not observed with higher ferric ion concentration. The copper recovery increased significantly with H2O2 concentration, and over 80% copper recovery was obtained with 10% H2O2. For sample B, the copper dissolution kinetics were relatively fast and reached the maximum value in five hours. Around 60% copper were extracted in sulfuric acid and MSA solution. Copper recovery slightly increased after adding ferric ion and H2O2. Glycine is a weaker lixiviant for both samples, the copper extractions were 36% and 4% respectively. INTRODUCTION Chalcopyrite is the most abundant copper sulfide mineral on earth, and it is one of the most refractory copper minerals regarding chemical processing. The declining copper grade and depletion of copper oxide deposits stimulate the development of hydrometallurgical process to extract copper from chalcopyrite. The dissolution of chalcopyrite by ferric ion is normally illustrated as Equation (1) and (2) (Dutrizac & MacDonald, 1974): CuFeS2 + 4Fe3+ → Cu2+ + 5Fe2+ + 2S0 (1) CuFeS2 + 4Fe3+ + 3O2 + 2H2O → Cu2+ + 5Fe2+ + 2H2SO4 (2) However, slow kinetics are usually observed from chalcopyrite leaching at ambient temperature and pressure. Researchers attribute the slow kinetics to passivation during chalcopyrite dissolution, and different passivation products are also proposed (Klauber, 2008). In recent years, many efforts have made to develop new methods to extract copper from chalcopyrite, such as utilizing bacteria or stronger oxidant (Zhao et al., 2015; Ruiz-Sánchez & Lapidus, 2017).

Jan 1, 2019

By H. Z. Liu, J. M. Zhao, F. C. Wang

"Novel silicate-alginate composite beads containing 2-ethylhexyl phosphonic acid mono-2- ethylhexyl ester (P507) were synthesized and applied for the adsorption of Nd3+ from aqueous solutions. The adsorption amount of Nd3+ has been increased owing to the introduction of P507. The effect of equilibrium pH (pHe), the kinetic and isotherm experiments were investigated. The adsorption reaches equilibrium at 9 h and the maximum uptake capacity is up to 195.4 mg/(g dry adsorbent). The Langmuir isotherm equations are used to describe the adsorption process. Complete desorption can be realized with 0.2 M HCl within 20 min. INTRODUCTIONRare earth elements (REEs) have found various applications in different domains, such as metallurgy industry, ceramic industry, nuclear fuel control, photo-electro-magnetic functional materials owing to their unique properties. Neodymium (Nd), as a representative of all of the most valuable REEs, is widely used as catalysts, laser crystals, capacitors, rubber additives, Nd-Fe-B magnets, hydrogen storage and so on. Thus, the separation and purification of neodymium is significant. Unfortunately, Nd always coexists with other REEs and selective separation of the individual Nd from the REEs mixtures is still extremely difficult owing to their strictly similar atomic structures and chemical properties.Liquid-liquid extraction (LLE) and solid-liquid adsorption (SLA) are the most widely adopted techniques for the separation of REEs in the hydrometallurgical fields. The LLE process is well suited for large-scale continuous operation because of its inherent high capacity and fast kinetics. Nowadays, as a commercial extractant, 2-ethylhexyl phosphonic acid mono-2-ethylhexyl ester (P507) has been extensively studied for extraction and separation of REEs since it has considerably good extractability and high separation efficiency (Xu et al., 1992). SLA is one of the effective and green separation methods with some prominent advantages, such as easy regeneration of adsorbents, small footprint size, less industrial wastes, higher enrichment factors and column efficiency,rapid solid–liquid separation without emulsion and so on. Hence, the introduction of extractants with excellent performance into adsorbents will integrate the advantages of LLE and SLA (Lee et al., 2009)."

Jan 1, 2012

By Wilson Blake

Rock deformation and failure taking place around underground openings is usually both accompanied and preceded by the phenomena of rock noise or microseismic activity. These small-scale releases of seismic and acoustic energy can be detected with special geophysical monitoring equipment. Use of this equipment allows one to look inside a rock mass to determine how an opening is behaving under the applied loading system. Microseismic equipment and monitoring techniques are briefly reviewed, and use of the microseismic method as an engineering tool in monitoring rock structure stability is illustrated by case histories. Examples cited range from evaluating roof stability using single-channel portable equipment, to rock burst monitoring using sophisticated computer controlled, multichannel monitoring systems.

Jan 1, 1983

By Malcolm Scoble, Sean Dessureault, Scott Dunbar

Budgets are key financial and behavior drivers for most businesses, including mining. Budgets are used to link strategic objectives to tactical decisions, to measure performance, and to provide basic financial planning. More accurate and pertinent budgets should result in improved strategic decision making and performance measures. This paper discusses how a process based production and cost database, based on activity based costing models and the one year production plan, can be used to create the annual budget for an operating mine as an Activity Based Budget (ABB). A case study is used to compare budgets derived from traditional methods and an ABB approach. It is evident that the ABB method is more accurate.

Jan 1, 2002

By Thomas M. Barczak

A theoretical evaluation of the impact of horizontal load on shield support capacity is made from a static rigid body analysis of the shield structure. Parameters affecting horizontal support resistance are investigated for a typical too-leg shield design. Horizontal forces acting on a roof support element are found to be both roof-generated and shield-generated. The impact of shield-generated horizontal forces on roof strata is also discussed from a theoretical viewpoint in relation to desired ground control. A technique is described whereby horizontal loading of shield supports can be measured underground. Horizontal load measurements from two different longwall faces were found to be significant, ranging from 20-35 pct of measured vertical load.

Jan 1, 1984

By FRANK COLE

THE territory covered in this discussion includes all the states west of the Mississippi river. Agriculture is expanding each year in this section, but until recent years the application of commercial fertilizers as an aid to crop production was not practised to any great extent. The use of commercial fertilizers has increased somewhat, but is still on a small basis as compared with the tonnages used else- where in the United States. During 1928 these western states used 665,100 tons of all classes of fertilizer as compared 'with 7,933,600 tons used in the whole United States; or this western area, compromising near- ly two-thirds the land area, uses about 5 per cent of the total fertilizer. To show how large a tonnage one state may consume, North Carolina for the year 192s used 1,349,360 tons of commercial fertilizer or about twice the amount used by 22 western states.

Jan 1, 1930

The cost benefits of controlling dilution of extracted ore have been very well understood by miners and mining professionals for many years. However, as we strive towards more mechanization, the dilution factor has been compromised in order to fit ?equipment? that is better suited to provide improved safety and productivity. Alternately, the drilling and ground support is accomplished by handheld drilling. In 2007, a short study, commissioned by CAMIRO (Canadian Mining Industry Research Organization) on the safety of hand held drilling vs. mechanized drilling, concluded that the risk of injury with handheld drills was seven times greater than with mechanized drills. Armed with this data, MEDATech Engineering proposed to the CAMIRO group to fund development of a ?MICRO Bolter?.

May 1, 2009

By J. Burns Read, S. Tour

It is the purpose of this paper to summarize, as far as possible, the metallurgical information and experience gained by the Ordnancc Department, during the war, in the manufacture of artillery cartridge cases, to describe the tests to which artillery cartridge cases were put, and to summarize the knowledge and experience gained in this testing. The authors wish to acknowledge the aid given by manufacturers, army officers, and civilian employees of the Department in obtaining data. Artillery cartridge cases are cold drawn from circular disks punched from strips of rolled brass. The rnanufacture involves from 25 to 30 main operations, which are done almost entirely on a punch press. Descriptions of the operations have appeared in various periodical:: and, therefore, will not he given here. After each cupping, or drawing, operation, except the last, the cases are annealed at from 540" to 650" C. (1000" to 1200°F.), to remove all the hardening stresses set up in the metal and to allow complete recrystallization. After each annealing, the cases are pickled in niter cake or sulfuric-acid solution and then washed in water to remove all traces of acid. In some instances, the cases arc then immersed in a cyanide-salt solution, and afterwards rinsed in water, to remove the thin layer of copper that forms on the surface of the cases during the acid pickle. The last cold-drawing operation is followcd by the heading operation which, by flattening the head of the case on the outside, causes the metal to flow on the inside to approximately the proper finished dimensions. The mouth, or open end, is then annealed at 430" to 450" ('. 1800" to 900" F.) by immersion in a salt bath or by gas flames. After being washed, the eases are tapered, when they arc ready for machining, inspection, and testing. Cartridge-case Disks Good disks of proper composition and physical properties are essential to the production of good cartridge cases. The Ordnance Department

Jan 1, 1923

By J. Burns Read, S. Tour

It is the purpose of this paper to summarize, as far as possible, the metallurgical information and experience gained by the Ordnancc Department, during the war, in the manufacture of artillery cartridge cases, to describe the tests to which artillery cartridge cases were put, and to summarize the knowledge and experience gained in this testing. The authors wish to acknowledge the aid given by manufacturers, army officers, and civilian employees of the Department in obtaining data. Artillery cartridge cases are cold drawn from circular disks punched from strips of rolled brass. The rnanufacture involves from 25 to 30 main operations, which are done almost entirely on a punch press. Descriptions of the operations have appeared in various periodical:: and, therefore, will not he given here. After each cupping, or drawing, operation, except the last, the cases are annealed at from 540" to 650" C. (1000" to 1200°F.), to remove all the hardening stresses set up in the metal and to allow complete recrystallization. After each annealing, the cases are pickled in niter cake or sulfuric-acid solution and then washed in water to remove all traces of acid. In some instances, the cases arc then immersed in a cyanide-salt solution, and afterwards rinsed in water, to remove the thin layer of copper that forms on the surface of the cases during the acid pickle. The last cold-drawing operation is followcd by the heading operation which, by flattening the head of the case on the outside, causes the metal to flow on the inside to approximately the proper finished dimensions. The mouth, or open end, is then annealed at 430" to 450" ('. 1800" to 900" F.) by immersion in a salt bath or by gas flames. After being washed, the eases are tapered, when they arc ready for machining, inspection, and testing. Cartridge-case Disks Good disks of proper composition and physical properties are essential to the production of good cartridge cases. The Ordnance Department

Jan 1, 1923

By C. Camurri

Results from the Metallurgical Department of Universidad de Conception showed that fire-refined copper could be rolled without previous remelting for deoxidation. The goal of this work is to determine the rheology of fire-refined copper from tensile tests at different temperatures and strain rates, and Ford plane compression tests. All that in order to simulate and calculate rolling process variables. For rheology hardness coefficients, n variables between 0.28 at 600°C and 0.46 at ambient temperature are obtained. The sensibility coefficient for strain rate m varies between 0.056 at 600°C and 0.006 at ambient temperature. The activation energy for plastic flow Q in the considered temperature range is 1436 cal/mol.

Jan 1, 1999

By S. P. Lin

The numerical models of nonlinear piles for deep foundations are studied in this paper. The purpose of these is to clarify the mechanical behaviour of deep foundation nonlinear piles subjected to axial and lateral loadings. Based on the site data of p-y curve as well as t-z curve of foundation soils, it is possible to evaluate pile performance under above mentioned loads by means of combined FEM/FDM models. Numerical examples are presented in tall building and offshore jacket for illustrating the technique, it show high efficiency of these models. Some information to be interested by design engineers are given, especially for those who pay very concerns on the interaction behaviours of structure and its pile foundation.

Jan 1, 2010

By Robert L. Opila

Negative electrodes for alkaline nickel-metal hydride batteries composed of MmNi3.5Al0.8Co0.7, where Mm is misch metal, have been characterized electrochermically and using x-ray photoelectron spectroscopy. The stability and rapid hydriding and dehydriding kinetics of the alloy in KOH are attibuted to a surface film. The protective surface film is shown to consist of an porous, outer hydrated layer and a dense, inner oxide layer. In addition, metallic nickel and cobalt are found throughout the film, and are presumed to form a conductive, percolative network that permits rapid electron transfer from the bulk to the solution, allowing rapid electrochemical formation of atomic hydrogen.

Jan 1, 1997