Search Documents

By Edgar L. Horner

"The objectives of the Wabush Mines tailings stabilization program are to control dust Ii/t-off and to rehabilitate the disposal area. The evolution of the program started with test plots in 1970, these being continued and expanded upon through 1974. In 1976, a 35-acre vegetation field trial was attempted and failed, part of the failure being attributed to lack of adequate equipment. Subsequently, equipment was purchased and during the summer of 1979-80 extensive areas were treated. The program was also expanded to include the evaluation of chemical and water spray stabilization versus vegetation in areas where shorter-term control is required. In addition, during the summers of 1979-80, spruce bog material was spread over about 100 acres and seeded.The approach to reclamation by vegetation at Wabush is one of soil building. Work to this point indicates that iron ore tailings can be converted to a soil capable of supporting plants. Plans for the Wabush tailings disposal area should make dust lift-off from inactive tailings areas negligible within the next few years."

Jan 1, 1981

By G. S. Walker, W. van Bronswijk

The accurate determination of free cyanide and metal cyanide complexes is of increasing interest to Carbon-in-Pulp (CIP) gold extraction operations as cyanide consumption is an important economic factor in the processing of complex ores. Characteristically complex ores are high cyanide consumers and these ores usually contain a range of sulfide minerals e.g. covellite (CuS), digenite (Cu1,S), chalcocite (Cu, S), Pyrrhotite (Feci-x)S), marcasite (FeS2), arsenic and antimony sulfides and zinc sulfide. These minerals can consume significant quantities of cyanide, e.g. various copper(!) cyanide complexes such as CuCN, Cu(CN)2·, Cu(CN)/ and Cu(CN)/ can form, depending on the cyanide to copper ratio in solution. Measurement of free and complexed cyanide is thus a prerequisite for efficient cyanide dosage control. Free cyanide can be determined potentiometrically or amperometrically but the methods are prone to error and are laborious [1]. Metal cyanide complexes can be determined by reverse phase HPLC, however, the species ofa single cation (e.g. Cu(CN)i-, Cu(CN);2 and Cu(CN)/) elute as one species [2]. Additionally the high amount of suspended matter in CIP leach solutions tends to introduce errors. Raman spectroscopy has the potential to be used as an in­line or on-line method of analysis. Free cyanide and the cyanides of gold, silver, copper and iron have been studied in aqueous alkaline solutions with a view to developing such a method. Spectra were obtained with a Bruker RFSl00 FT-Raman spectrometer using a 1064 nm laser delivering 800 mW of power at the sample. Depending on the solution, 250, 1000 or 4000 scans at 4 cm-1 resolution were accumulated. The cyanide stretches observed were relatively narrow (10 15 cm-1 full width at half height) and well resolved (Figure 1 ).

Jan 1, 1995

By G. D. West, J. D. Purdue

"Marked Ball Wear Testing (MBWT) employs identified grinding balls which are placed in an operating mill for a period of time, retrieved from the mill, and then measured to determine the amount of wear experienced. This is an excellent method to evaluate the relative differences in the wear rates of various grinding ball materials and/ or manufacturing process variables simultaneously and under actual production milling conditions. This paper outlines the methods of ball identification, testing and evaluation procedures and discusses the strengths, weaknesses, and proper application of marked Ball Wear Test results. INTRODUCTIONThe consumption of grinding media in the mineral processing industry represents a substantial cost to the comminution process. Grinding media is most often found to be the second highest consumable cost next to energy. To determine the selection of the most cost effective media, one must determine the specific wear mechanisms present in a given grinding application and decide which media system addresses these mechanisms most economically.A MBWT has definite advantages over other methods used to evaluate the relative consumption rates of grinding media. It allows the comparative testing of a large number of different ball types under identical operating conditions in a very short period of time. In addition, production wear rates can be accurately predicted directly from MBWT results. Typical MBWT test periods are in the order of 350 to 700 operating hours for high wear rate application and upwards of 2000 or 3000 hours for low wear rate applications. These times are much less than the 5000 or more hours required to purge a mill of the incumbent ball charge (to convert it to the test ball) and then provide even a minimal test period in which to conduct a full production test, for just one type of ball. Under production test conditions the evaluation of competitive product or the development of improved grinding balls is necessarily slow."

Jan 1, 1991

A price list of publications of the Geological Survey, complete to May, 1931, and with separate monthly notices of publications to (late, will be sent upon application to The Director, United States Geological Survey, Washington, D. C. A leaflet is issued each month listing new publications; it will be sent upon application to the Director, as well as Circulars containing information about topographic maps. Book publications of the Survey include (1) Annual Reports, (2) Monographs, (3) Professional Papers, (4) Bulletins, (5) Water Supply Papers, (6) chapters and volumes of Mineral Resources of the United States, (7) Folios of the Geologic Atlas of the United States and the World Atlas of Commercial Geology, (8) Topographic Folios and Topographic Maps that bear descriptive texts. Monographs, Folios of the Geologic Atlas of the United States and the World Atlas of Commercial Geology, and Topographic Folios and Topographic Maps, are not distributed free. A publication of one of the other classes can be distributed free only until the end of the fiscal year following that in which it was issued. No person can obtain more than one free copy of the same publication, and general requests for free publications, such as all of any series or all on any subject, can not be granted. In ordering publications one is requested to give both the series designation, as Bulletin 738 or Professional Paper 122, and the title. Give full address, plainly written, including county. Prepayment is required and may he made by postal, or express money order payable to the official charged with the sale of the publications. requested, as indicated in the discussion of each classification following; or it may be made in cash-exact amount -at sender's risk. Postage stamps are not accepted in payment for publications.

Jan 1, 1933

By J. E. Chilton

Regular monitoring for methane gas is required near working faces in gassy underground mines where the potential for methane ignitions is greatest. However, high concentrations of methane can also accumulate outby the face where methane levels are monitored less frequently. Wearing a personal methane monitor equipped with an alarm could protect persons working in these outby areas from injury or death due to methane ignitions. The National Institute for Occupational Safety and Health (NIOSH) has conducted studies to evaluate methanometers that could be used as person-wearable monitors. For the present study, seven different person-wearable monitors that are not currently approved for underground use were evaluated. This paper describes test procedures used to evaluate performance of methane monitors that could be used underground for continuous personal monitoring of methane. The information in this report provides data that allows the reader to make side-by side comparisons of these instruments.

By David R. Hanson

Experimental work performed by the Bureau of Mines in a laboratory environment has shown that the formation of failure zones within certain rock types is accompanied by the emission of significant amounts of radiofrequency (RF) electromagnetic (EM) energy. This radiation was detected using nonresonant, "electrically short," broad-band antennas. Rock types for which emission was observed include granite, quartzite, and taconite; sandstone and marble did not emit measurable radiation. Amplitude spectra of the radiation showed the energy to be concentrated between 10 and 40 kilohertz. These data indicate that emission is directional, but this has not yet been proven. In addition, amplitude of RF emission increases with increasing crack size. Since emission was observed only for brittle quartz-bearing rocks, it appears the formation of piezoelectric fields is a necessary condition for RF radiation. Plausible mechanisms for emission include rapid decay of piezoelectric fields accompanying the sudden stress release at failure and/or the acceleration of an "exoelectron plasma" through the intense local piezoelectric fields. Since emission appears to increase with the scale of failure, and since antennas do not need to be coupled directly to rock surfaces as with conventional geophones, the possibility of developing a portable system to monitor seismically active areas exists.

Jan 1, 1981

By E E. Hall, C D. Taylor, D S. Yantek

Regular monitoring for methane gas is required near working faces in gassy underground mines where the potential for methane ignitions is greatest. However, high concentrations of methane can also accumulate outby the face where methane levels are monitored less frequently. Wearing a personal methane monitor equipped with an alarm could protect persons working in these outby areas from injury or death due to methane ignitions. The National Institute for Occupational Safety and Health (NIOSH) has conducted studies to evaluate methanometers that could be used as person-wearable monitors. For the present study, seven different person-wearable monitors that are not currently approved for underground use were evaluated. This paper describes test procedures used to evaluate performance of methane monitors that could be used underground for continuous personal monitoring of methane. The information in this report provides data that allows the reader to make side-by side comparisons of these instruments.

Jan 1, 2005

By D. Dunbar

Flooding of open pits now receives considerable attention from the mining industry as an option that may minimize environmental impacts, particularly when anoxia in pit lake deep waters can effectively eliminate oxidation of pit-wall sulphides. A state-of-the-art, coupled physical-geochemical pit lake model is used to verify that a cost-effective, environmentally responsible closure strategy for the open pit at the Kori Kollo gold mine, southeast of La Paz, Bolivia is to adopt a controlled, two-stage infilling of the open pit upon cessation of operations. By filling the pit initially with highly saline waters from evaporation/infiltration basins and naturally saline deep groundwater, followed by capping with fresh river water, a very stable and strongly stratified pit lake will be developed. In addition, the stratification will result in the isolation of metal-rich saline bottom waters from surface waters of good quality. Results of this model provide defensible predictions of the physical stability and evolution of water quality in the Kori Kollo pit lake over time. The model results indicate that anoxic conditions will develop below the fresh-saline water boundary within 1 to 2 years, followed by the rapid onset of sulphate reducing conditions in the bottom waters. Hydrogen sulphide produced by sulphate reduction will readily react with dissolved metals to form highly insoluble metal sulphides. The process results in the gradual removal of metals from the water column and the concomitant improvement of water quality over time. A notable benefit of this strategy is that it can be fully integrated with other mine site closure options as well as future environmental management strategies. The proposed plan allows for: 1) safe storage of saline evaporation basin waters; 2) the potential for passive treatment in anoxic bottom waters of ARD seepages from other mine site operations should they arise; and 3) a repository for future reactive wastes that could be effectively isolated in a physically and chemically stable environment.

Jan 1, 2001

By Willem J. Marais

The management of unpaved mine road networks on large surface mines rarely results in optimal road maintenance strategies and minimised total road-user costs. This is ascribed mostly to the complex and dynamic combination of variable road networks and loading and discharge points. In a dynamic mining environment - typically those mines in which production is managed by a centralised truck dispatch system ? there is no guarantee that a particular road maintenance intervention will contribute significantly to reducing total road-user costs or increasing productivity. Most large surface mines operating ultra-heavy mine trucks rely on an integrated on-board diagnostic data collation, communication and GPS-asset location system as a real-time fleet management tool. By extending this system to incorporate a multi-sensor analytical procedure in which specific truck vital signs are monitored and filtered, a road defect can be recognised and a trigger level set to relay the location of defects on the mine haul road to the centralised truck data management system. Previous work established the feasibility of the multi-sensor approach to road defect recognition on large mine haul trucks, and outlined the defect recognition, analytical and modelling issues and system limitations. This paper presents the development of the analytical procedure used as a basis for evaluating the truck on-board data to establish maintenance priorities amongst a network of mine roads. Following an introduction to the system architecture, the results of system field trials are analysed and the results discussed in the light of defect density and traffic volume as the primary variables in an approach to prioritising road maintenance. The paper concludes that by supplementing the existing mine communication and asset management systems, road maintenance can be managed on a near real-time basis and maintenance equipment dispatched to where most immediate benefit will realised from a maintenance intervention on the network, thereby generating the maximum improvement in service and reduction in cost per ton hauled.

Jan 1, 2008

By F. D. Patchen

Changes in the properties of partland cement upon the addition of fine-ground silica are discussed. Data were collected from formulations cured for periods up to 60 days at temperatures varying from 180" to 350°F. Compressive strengths, permeabilities and thickening times are compared. It is demonstrated that addition of find-ground silica in proper proportion results in a hydrated cement with superior properties above 230°F; i.e., early compressive strengths are higher and increase with additional curing, permeabilities are significantly lnrver and thickening times are increased. X-ray analysis of hydrated cement samples have been used to determine more fully the complex chemistry of these systems. Dicalcium silicate alpha-hydrate was found in all neat cements cured above 260°F. A 10 weight per cent silica addition produced a maximum amount of this phase. Xonotlite and tobermorite have been identified as hydration products at 320°F in systems containing 35 or more weight per cent silica. Formation of these components appears to be primarily responsible for the gain in strength and reduction of permeability observed after the addition of silica. INTRODUCTION For several years it has been recognized that loss of compressive strength occurs when portland cement is cured at a temperature above 250°F. This phenomenon has been called "strength retrogression". More recently it has been recognized that increased permeability usually is associated with decreased compressive strength at these temperatures. At curing temperatures above 300°F, these factors reach serious proportions. A compressive strength loss of 50 per cent between curing times of 24 hours and 14 days has been reported,' and permeabilities as high as 10 md have been measured in neat cements cured at 320°F for seven days.' Earlier investigators,' although unsuccessful in eliminating strength retrogression, stated ". . . .it appears possible that by the proper selection of additives for cement, strength loss with age at high temperatures can be either eliminated or considerably lessened". One solution suggested was the use of a pozzolanic material, hydrated lime, and a retarder. Menze15 in 1934 discovered that portland cement containing finely divided silica possessed high compressive strengths when the curing temperature was 350°F. The use of such a composition is now an established practice in the manufacture of steam-cured cement blocks. It is reasonable to assume that the same beneficial effect can be used advantageously in high-temperature oilwell cementing operations. Ludwig first mentioned the use of sand for this purpose. Later, a portland cement containing moderate additions of silica flour and retarded with CMHEC, a cellulose derivative. was recommended for high-temperature application." These formulations have been successfully employed in the field."'" This paper presents the results of a research program to test the efficacy of finely ground silica in increasing the compressive strength and reducing the permeability of oilwell cement compositions containing portland cement. Included also are X-ray diffraction patterns of powdered samples which have been used to determine some of the important chemical reactions occurring in these systems. LABORATORY PROCEDURES AND MATERIALS All compressive-strength test specimens were prepared and cured from a slurry in accordance with API RP 10B, with two modifications. A final curing pressure of 5,000 psi was maintained for a one- or three-day period; but, for further curing, pressures were reduced to the vapor pressure of water at the curing temperature. Also, the water content was varied in samples containing silica to maintain the slurry viscosity within a range of 5 to 15 poise as measured on a consistometer. Test specimens at 180°T were cured in a water bath at atmospheric pressure. At higher temperatures the specimens were cured in a steam-jacketed high-pressure curing vessel at 5,000 psi for a one- or three-day period. cubes cured for longer periods were removed from the pressure-curing vessel after 24 hours, sealed in small bombs containing water and placed in an aging oven.

By R. A. Lohnes, S. M. Levorson

As part of research to develop a coal handleability index that predicts the ease with which coal will flow through a handling system, comparative tests were conducted with a Johanson Indicizer and a low-stress triaxial apparatus on 12 coals at a variety of gradations and moisture contents. The lndicizer test provides a rapid method for generating data associated with coal handling characteristics. The arching index measured with the Indicizer is a function of the geometry of the apparatus as well as the properties of the coal. The handleability index determined from triaxial data is a more direct measure of coal characteristics. The handleability index shows a wider range of values than the arching index and, therefore, appears to be more sensitive to coal variations. Neither the arching index nor the ratholing index, as measured with the Indicizer, agreed well with the handleability index. This is attributed to differences in sample preparation as well as to the tests themselves.

Jan 1, 1993

By Wm. Monay

MR. MONAY (Vice President Kinney Coal Co., Scofield, Utah): The past year and a half has witnessed a series of coal mine disasters in Utah and Wyoming, concentrated into the short space of a few months, following a long period of years in which the industry was comparatively free from devastating calamities. The natural result has been a hysterical activity on the part of bureaus, commissions and professional reformers who know little about coal mining from a practical standpoint. This activity has been met by the industry in Utah with an attitude of submission, no doubt the result of the fear of being misunderstood by the public. But it is my firm conviction that the lives and property of the coal industry will find their surest guaranty of protection in the humanity, and in the self interest of those operating and working in the mines, rather than in governmental regulation. Inelastic, inflexible blanket statutes and rules will simply stifle and hamper the initiative and progress of our industry in working out its own salvation, under the varying and changing conditions of different localities, different conditions, and in different mines. We who have spent our lives in digging in the mines and operating them, know more about this business than anyone else and I believe it is time for us to speak up and no longer sit meekly by while inexperienced bureaus and unskilled commissions make up laws, rules and regulations for us which when made are on the books to stay, even though in a short time they may prove inapplicable, in whole or in part, or be superseded by something different, and which in some cases create new dangers or lull us into a false sense of security. Shortly after the Castle Gate explosion in March, 1924, a new set of safety rules was issued by the Indus- trial Commission of the State of Utah to become effective July 1st of the same year, the most important of which prohibits the use of black powder in any mine--gaseous or non-gaseous; prohibits the use of open flame lamps in any mine-gaseous or non-gaseous; and requires that rock dusting in all main haulage ways as far as the freezing point and required that all mining machines be equipped with water to be applied while cutting. These rules have been characterized as "Utah's Monument to her Dead Miners" in a large poster spread broadcast over the country from an office in New York that styles itself the Association for Labor Legislation. In reviewing the coal mining history of the State of Utah, in the year 1900, a serious disaster occurred at Winter Quarters. The cause of the same is believed to be an explosion of powder that was stored in the mine, which was a common practice in the early days, and from that time until the Castle Gate disaster, March 8, 1924, a period of some twenty-four years, no explosion of any kind occurred in this district. During all this period open lamps were used, considerable black powder was used, rock dusting was unheard of, sprinkling with water was very generally done-all without any catastrophe. Since the adoption of the new rules, we have 'had a very violent explosion at the Carbon Fuel mine in Spring Canyon. At the time of this explosion, 3,000 feet of the main slope had been rock dusted several times between July 1st and September 21st. The second left entry, which is a main haulage way, a distance of 3,000 feet was completely rock dusted on the date of the explosion. This mine is not considered extremely gaseous, yet an explosion as violent as that of the Castle Gate mine occurred. Some thirty men who had been loading coal in various parts of the mine on this Sun- day, the day of the explosion, and other men employed in rock dusting the second left entry, had just left the mine a little while before it occurred, and no abnormal condition in the mine was noted. At the time of the explosion five machine men were in the mine.

Jan 1, 1925

By M. J. Virnig, G. A. Kordosky, K. D. MacKay

LIX 34 liquid ion exchange reagent, one of a totally new class of metal extractants, is discussed in terms of its properties. Specifically, these properties include improved selectivity for copper and greater recovery. Some comparisons to the well known General Mill's LIX 64N have been made. Particular emphasis is given to treating solutions containing very low copper values and high impurity levels.

Jan 1, 1978

By Walter Harvey Weed

CONTENTS. [ ] INTRODUCTION. THIS paper deals with certain ore-deposits whose structural features or mineral contents (or both) result, directly or indirectly, from igneous intrusions and their after-effects. It is largely a discussion of contact metamorphic ore-deposits based upon the physical changes in rocks due to contact action. It involves a classification of ore-deposits only so far as is abso-

Jan 1, 1913

By AMIR EHSAN KIANFAR, Moritz Ziegler, TOBIAS HARTMANN, ELISABETH CLAUSEN

Accurate positioning information is a central step in the process of increasing automation and digitalization in the mining industry. Underground mine environments are prime examples for GNSS-denied environments that pose several additional challenges for the employed indoor positioning system (IPS). This work presents an ultra-wideband (UWB)- based system specifically tailored for underground mine environments. Initially, the UWB technology is reviewed and basic concepts of IPS are explained. Both software and hardware are described in detail, including positioning algorithms, electrical circuitry and the mining-compatible enclosure. Finally, the results from field tests in an underground mine are presented and positioning performance and the influence of dilution of precision (DOP) on positioning results are empirically evaluated. The results show that the localization errors are mostly below 1 m. Individual zones of high localization errors are suspected to be caused by noise interference. Significant DOP influence due to the mining drift geometry can be confirmed. The system shows promising localization results for different mining applications, while influences negatively impacting the accuracy are presented as items for future research.

Jan 1, 2024

By Chu E. Ho

Jet grout column formation at large depths are prone to several uncertainties, such as inaccuracy in setting out boreholes, drilling deviation, soil variability and reduced jetting energy at the nozzle. This would result in shorter cutting distance of the jet, with potential lack of interlock between grouted columns. A design strategy for mitigating the risk should include a soil investigation program aimed at discovering potential variability in soil conditions at the locations of jetting. Determination of soil strength profiles with depth would be useful for evaluation of jetting parameters and prediction of the achievable cutting distance at any depth. Selection of design column spacing should include allowance for setting out accuracy, verticality of the boreholes and the achievable jet cutting distance. For deep jet grouting operations, it would be necessary to take into account the energy losses at the nozzle inlet; however the increase in the presiding pressure at the nozzle outlet at depth is small relative to the range of jetting pressures commonly employed and would not affect the cutting distance to any significant degree. Design column spacing should not be so close as to cause problems with ?masking? which may lead to localized ungrouted zones of soil. For effective field control, boreholes should be cased up to the top elevation of the grouted zone so that the orientation of the borehole can be measured prior to grout injection. An analytical equation for calculating the cutting distance is proposed for adjusting jetting parameters where necessary to compensate for drilling deviation and changes in soil conditions. It is preferable that jet grouting trials be executed at elevations that correspond to the actual production jet grouting depths for accurate evaluation of jet cutting performance.

Jan 1, 2008

By Julie Q. Shang

The electrokinetic (EK) technology for dewatering of two tailings from the uranium mines in Northern Saskatchewan is studied in bench scale experiments. The study includes four phases: 1. Characterization of two uranium mine tailings; 2. Assessment of voltage loss on the coated Ti anode and water interface. 3. EK cell test series to measure electrokinetic permeability (ke) of two tailings; 4. EK dewatering test series to study electrokinetic enhanced gravity dewatering on two tailings samples. The results have demonstrated that both tailings responded positively to the EK process. For the tailings containing gypsum, the EK dewatering should be a short term process (within one hour) with anode conditioning (pH adjustment). The tailings containing clay minerals responded well to EK dewatering, in which pH adjustment is optional and will further enhance the EK flow. Both tailings as tested have low hydraulic conductivity and are particularly suitable for EK dewatering and consolidation.

Aug 1, 2010

By Charles E. Glass

The purpose of this report is to demonstrate the flexibility of rte sensing techniques for providing data with which to implement mined-lands reclamation in an efficient and cost-effective manner. An operational program is presented for using satellite remote sensing data, collateral data, and automated image analysis to provide: 1) an inventory of coal and copper mines and mine waste in Arizona, 2) techniques for periodic monitoring of mining areas using multitemporal classification and image prediction techniques, and 3) delineation of high priority areas for future reclamation and current land-use planning of Arizona mining areas based on environmental hazards indices computed using classified scenes and collateral data.

Jan 1, 1980

By P. L. De Bruyn

The behavior of collectors at the mineral-solution interfaces is usually explained in terms of an ionic adsorption process. Through the distribution of collector ions between the solid surface and the co-existing solution phase the mineral is believed to acquire a water-repellent surface coating. Quantitative adsorption studies have been made on simple flotation systems only within the last few years. Such investigations were made possible by the adoption of the radiotracer method of analysis. As a consequence of these studies a new parameter has been added to aid the understanding of the flotation process.

Jan 3, 1955

By D Linn Coursen

In the proposed method, the charges are elongated and arranged in one or more arrays. The orientation of each charge in an array, its velocity of propagation of explosion, and the velocity of propagation of vibration in the formation are such that, at an outlying location where vibration is to be reduced, the onset of vibration from explosion of the first negligibly small increment of each charge arrives a finite time before that from explosion of the last negligibly small increment of that charge. The charges of each array are fired in accurately-timed sequence, with the times between initiations chosen so that, at the outlying location, the onset of vibration from explosion of the last small increment of each charge, except the last charge, arrives a negligibly small increment of time before the onset of vibration from explosion of the first negligibly small increment of the succeeding charge. With such timing, vibration may be reduced at the widest range of locations by tilting the boreholes so that the terminal end of each charge is directly above or below the terminal end of the succeeding charge.

Jan 1, 1995