Search Documents

By Borsaru M, Wylie AW

A neutron irradiation technique has been developed which is suitable for the determinat- ion of the iron and aluminium content of iron ore fines (-6 mm particle size) on a moving rubber conveyor belt. The determination of iron entails measure- ment with a NaI(Tl) gamma ray detector of the characteristic prompt gamma rays (7.64 MeV) due to thermal neutron capture in iron, while the determination of aluminium is based on thermal neutron activation analysis. For the latter a second detector must be placed down- stream to monitor the 1.78 MeV gamma radiation emitted after activation of aluminium. Although conveyor speed has no effect on the Fe measurement, it has an adverse influence on the aluminium signal, and the belt speed should not exceed 0.1 m/s if good accuracy is required. Static trials on a 460 mm rubber conveyor belt with constant ore geometry indicate that for iron an accuracy of ¦ 1.2% Fe (2a) can be achieved for crushed run-of-mine ore at

Jan 1, 1978

By Frank Doxey

Louis A. Turnbull (U.S. Bureau of Mines, Washington, D. C.)—This paper is a well-organized concise discussion of progress in mechanization at coal mines in Nova Scotia during the last 50 years. It shows the perseverance and resourcefulness of those responsible for the production of high-quality coal essential to steel production in the area. The development of the Dosco miner and its use in longwall mining at the Sydney

Jan 1, 1955

By Andrew P. W. Briggs, Corale L. Brierley

A considerable economic and technical knowledge base has been amassed with the successful and sustained operation of commercial minerals bioleaching/biooxidation plants to extract copper from chalcocite ore and enhance precious metal recovery from sulfidic refractory ores and concentrates. Economic evaluation ofbio-processing must consider the value of the ore, the sulfide-sulfur requiring oxidation to achieve significant metal recovery, the time required for the biological process and, in the case of precious metal feed-stocks, the down-stream reagent consumption. Of these considerations oxygen requirement for the biologically-catalyzed oxidation of sulfide minerals is the prevailing determinant in the capital and operating costs of aerated, stirred-tank reactors for processing concentrates and bio-heaps for processing ores. Oxygen requirement is dictated by the amount of sulfide-sulfur requiring oxidation to achieve desired metal recovery. The testwork program to evaluate a project for application of biooxidation/bioleaching must be designed to insure that factors critical to economic assessment are fully quantified.

Jan 1, 1997

By J. Esterle, J. Kruttschnitt

Fragmentation modelling in soft rocks presents a challenge due to their propensity to further fragment after blasting during normal handling. Coal and some iron ore deposits are examples of materials that undergo significant degradation during the extraction, hauling and dumping process of the mining operation. The Kuz-Ram model is an empirically derived predictor of size distribution from blasting hard rock. Little breakage occurs during excavation and subsequent sizing of hard rock, so the measured Run of Mine (ROM) size distribution is essentially the same as the post-blast (before excavation) size distribution. However, for soft rocks, each step of the excavation and hauling operation imparts energy to the rock particles so the measured. ROM size distribution will be significantly different from the postblast size distribution. In order to calculate the ROM fragmentation at any stage of the extraction (or sizing) operation, the JKMRC has developed a model that combines both blast fragmentation and degradation through subsequent handling.

Jan 1, 2001

By Antonio Marrano, Eda F. Quadros, Diogo Correa [Fo], Paulo T. Cruz

For many years the water pressure test has been used as a normal procedure to investigate the hydraulic characteristics of rock masses and discontinuities. Although the test has given evidence of problematic areas, the nature of flow and the so called equivalent permeability are seldom seriously affected by the testing tecnique. In order to improve the information on these points the Instituto de Pesquisas Tecnológicas de São Paulo - IPT, has developed an extensive program at laboratory and field research on the hydraulics at rock fractures. This paper summarizes the main items related to this research. Is shows that with only small improvements on field tests and some support of laboratory conductivity tests on natural rock joints it is possible to obtain a better understanding of the nature of flow in fractures, improve flow predictions and estimate the opening and hydraulic conductivity, as well as the transmissivity of natural joints or rock discontinuities.

Jan 1, 1982

By J. Riccardi

Copper refineries use massive copper castings as moulds into which impure molten copper from the reverberatory furnace is poured to form anodes for further electrolytic refining. To facilitate removal of the copper anodes from the mould and to prolong the life of the mould itself, it is traditional to spray the mould surface prior to each use with a slurry of baryte in water. This slurry application leads to poor housekeeping, operating costs are escalated by the cost of the slurry, and additional problems in the subsequent refining process are experienced due to carry-over of excess undesirable baryte powder. A one-time application of a diffused layer of aluminum to the surface of the copper mould prior to putting the mould into service has been found to provide extended mould life and facilitate anode removal, as well as reducing baryte consumption; thereby reducing operating costs at both the anode manufacturing and refining stages.

Jan 1, 1999

By A. G. Sciulli, G. P. Ballock, G. Hearnshaw, K. K. Wu

Waste disposal underground is the most effective method when viewed from an environmental aspect. As costs of other methods of disposal continue to escalate, the cost effectiveness of underground disposal during the mining cycle becomes increasingly attractive. The use of concrete for sealing abandoned mines has proved to be suspect when associated with a relatively incompetent adjacent strata due to its shrinkage characteristics. Complete failure of the plug has been known to occur in some instances. A more effective, cost competitive seal can be obtained using pneumatically stowed material and incorporating a polyurethane grout, which has greater adhesion characteristics than concrete. Injection of the surrounding strata and of the stowed material helps to ensure an impervious barrier and prevent the plug from moving when subject to high pressure heads. When properly placed, impervious seals cause the old workings to flood, raise the mine pool level, and thus eventually eliminate the potential for oxidation, which is the primary cause of acidity in the water

Jan 1, 1987

By Jesse Jones

1. BRINELL tests at progressively increasing temperatures are given for a representative lead-base and a representative tin-base babbitt, showing that the former has superior resistance to deformation at the working temperatures of bearings. 2. Small squares of bearing bronze, tinned and then babbitted with a representative lead-base babbitt and a representative tin-base. babbitt were subjected to compressive loading. The lead-base babbitt showed less average compression than the tin-base babbitt. Compression did not materially increase the Brinell hardness of the babbitts. 3. A process and a tool are described for giving smoother and more accurate surfaces to bearings than has heretofore been possible. The following experiments have recently been carried out in the chemical laboratory of the Westinghouse Electric and Manufacturing Co., Pittsburgh, Pa. While the work is incomplete, it is described at the present time because data on the comparative merits of lead-base and tin-base babbitts are of interest in connection with the present shortage of tin.

Jan 8, 1918

The Charters Towers 1:250 000 Gravity Data Set represents a new initiative of the Department of Resource Industries (DRI, formerly Queensland Department of Mines) to provide high quality regional gravity data over areas of the State that have high potential for new mineral discoveries. The Department has adopted a strategy to upgrade geophysical data to complement the ongoing Regional Geological Mapping Program (RGMP) of this Department and in areas where the data would be of most benefit to the mineral exploration industry. Part of this strategy is to ensure that these data are released within 6 months of data collection.The 1989 Charters Towers survey was completed as a joint project with the Bureau of Mineral Resources, Geology and Geophysics (BMR), and is the first regional geophysical data acquisition project undertaken by the DRI. Prior to this survey, the only gravity data in this area dates from the B MR regional surveys carried out between 1960 and 1967.

Jan 1, 1990

By A. G. Sciulli, G. P. Ballock, K. K. Wu

Waste disposal underground is the most effective method when viewed from an environmental aspect. As costs of other methods of disposal continue to escalate, the cost effectiveness of underground disposal during the mining cycle becomes increasingly attractive. The use of concrete for sealing abandoned mines has proved to be suspect when associated with a relatively incompetent adjacent strata due to its shrinkage characteristics. Complete failure of the plug has been known to occur in some instances. A more effective, cost competitive seal can be obtained using pneumatically stowed material and incorporating a polyurethane grout, which has greater adhesion characteristics than concrete. Injection of the surrounding strata and of the stowed material helps to ensure an impervious barrier and prevent the plug from moving when subject to high pressure heads. When properly placed, impervious seals cause the old workings to flood, raise the mine pool level, and thus eventually eliminate the potential for oxidation, which is the primary cause of acidity in the water.

Jan 11, 1986

By Richard Birk

Rf sputtered quartz has been successfully used in multilayer interconnects for MOS devices. The target potential was 2000 v peak to peak with a frequency of 13.56 Mc per sec. The sputtering rate was approximately 60A per min with an operating pressure of argon gas at 10 to 15 p. The dielectric strength is 8.0 x 10' v per cm and the pinhole density is less than 2 x 10-2 per sq mm. Infrared absorption peaks for the Si-O vibrational bands we at 9.4, 12.4, and at 22.5 p. The etch rate of the sputtered SiO2 is 1200A per min. MOS devices have been fabricated using multilayer interconnects with no degradation of electrical characteristics. MULTILAYER interconnects require an insdating film between the metal layers which can be deposited below any potential eutectic temperature. Sputtered Si4, which can be deposited with substrate temperatures below 200°C, satisfactorily meets the multilayer insulation requirements and has been used to prepare MOS circuits with multilayer interconnects. The physical and electrical properties of rf sput-

Jan 1, 1969

By D. Harris, M. Osterberg

This paper examines the economics of acquiring mineral exploration rights by royalty-rate bidding when the royalty basis does not provide for full cost recovery. Bidding takes place prior to exploration and the documentation of actual tonnage and grade. Consequently, it increases considerably the risk to exploration capital when the fraction of cost recovered is small and the product price exhibits large fluctuations. Price and grade risk are demonstrated on a 360-Mt (400-million-st) porphyry copper deposit by Monte Carlo simulation of discounted-cash-flow analysis. Copper price is modeled as a stochastic price process, and costs are based on US Bureau of Mines cost models. When both grade and price risk are considered, the probability for a negative NPV is 0.54, given a royalty rate of 5% applied to a basis that allows the recovery of costs up to 50% of product price. Investment risk could be considerably reduced by defining the royalty basis to allow greater cost recovery. Although such a basis would require society to share in the risk, society would benefit from greater resource development.

Jan 1, 2000

By Vernon E. Swanson, Tom G. Ging

Experiments indicate that simple addition of water to mixtures of untreated trona and otherwise insoluble leonardite yields a rich, black, slightly alkaline solution of concentrated humic substances. Prices of both trona from Wyoming and leonardite from South Dakota and Wyoming are very similar-$10-30 per ton. Leonardite is the term commonly given to naturally weathered, oxidized coal that is readily soluble in slightly alkaline water.1 Several tens of thousands of

Jan 1, 1973

By Leena Vesa, Antti Remes

Design of thickeners is based on laboratory test work, characterizing the material and determining the optimal reagents, dosages and settling regimes. Several methods for dimensioning plant scale equipment exist. Kynch and Talmage-Fitch design procedures has been applied widely for a long time. Nowadays, besides them, a dynamic laboratory test work is applied for design of high rate thickeners. In that the laboratory unit is operated with known solids load per area, feed and flocculation conditions and with raking of the underflow. All these test methods afford useful data for setting up and calibrating a dynamic simulation model of a plant scale thickener. This paper presents a flocculation kinetics based dynamic thickener simulation model and a procedure to calibrate the model parameters. With the model, the underflow stream composition can be simulated over time as a function of the thickener operating parameters, which are: the feed rate and composition, underflow pumping rate, flocculant dosage and dilution of the feed. In addition, the model incorporates calculation of the slurry bed level, the cone pressure, the yield stress and the rake torque. Such a dynamic modeling scheme enables setting up simulation aided operator trainings and developing and testing of advanced control strategies, for example. The unit model can be integrated as a part of concentrator-wide flow sheet simulation model as well. Here, calibration of the kinetic flocculation model based on a laboratory test case data and further the operation of a simulated plant scale thickener are presented.

Jan 1, 2014

There has been considerable attention in the literature to coarse sizing by wet and dry screening, but these methods have not proven to be applicable to the calculation of screen capacities for fine wet sizing, desliming and media recovery: A method is presented for the calculation of the size of screens for such duties, being based on the mean particle size of the oversize material on the screen which reflects the surface area from which the fines or media must be removed. Similarly for dewatering, it is the area from which the water must be drained. Desliming, media recovery and dewatering are each considered along with water require- ments both with the feed and as wash water.

Jan 1, 1984

By T. Vincent, J. Steele, C. Debrunner, M. Whitehorn

This paper presents current work on the development and use of stereovision for underground mining. Information on the calibration of the cameras and the feature-matching algorithm are presented. This system uses an intensity-based approach that evaluated correspondences along the epipolar line. Once features have been identified and their distance from the cameras computed, a three-dimensional map of the muck pile is developed. The approach used here uses a ray-tracing algorithm. This approach provides an uncertainty measure along with the elevation. A discussion of the use of this modelling information in the control of the LHD is included. Keywords: Robotics, automation, LHD, underground mining, vision sensing, task automation, tele-operation

Sep 1, 2001

By Wonn Soh

As for Earth, where human beings live, approximately 70 % of its surface is covered by oceans. Today, advanced technology has led us to understanding the abyssal ocean floor through the use of submersibles and ROVs (remotely operated vehicles) for the last 30 years. Furthermore, the oceanic crust beneath the abyssal floor still remains an unexplored scientific frontier due to the lack of a direct approach. Exploration of this frontier is required to enhance our understanding of the mechanism of the M.8 class plate-subduction-type earthquake, of generation of the big tsunami, that caused the disaster, and of the paleo-global environmental change as well as of the origin of life as viewed in deep water thermal vents.

By Sundar S. Saluja

Efficient and re1iable methods of fragmentation through blasting have been sought ever since the introduction of black powder in mining operations, but the pace of investigation became faster with the discovery of nitroglycerine. The development of modern measuring instruments and the need to blast more rock with the least damage has made the study of blasting mechanics and its application more important, particularly since the oil embargo. Investigations into the practical approach evolved by Daws (1909) and the work done to make it more useful is discussed. The work of several investigators is touched upon with particular reference to the development of computer programs to simulate and optimize blasting operations.

Jan 1, 1986

By Victor F. Hollister

The great increase in post-World War I1 use of molybdenum was made possible by discoveries of that metal in porphyry molybdenum and porphyry copper deposits. This section documents significant porphyry molybdenum discoveries of the post-war period. The most important discovery was Henderson in Colorado. It is not only one of the world's largest and richest, but it was found by a team of geologists who defined the hood model and tested it successfully at Henderson. Under the leadership of Stewart Wallace, these scientists established a set of criteria for exploration for Henderson-type de- posits that was copied by the industry. The discovery bf vertical cylinder type porphyry molybdenum deposits was less renowned. Boss Mountain in British Columbia and then Mt. Pleasant in New Brunswick were given relatively scant notice, compared with the Henderson discovery. However, these deposits have geometrics distinct from that found in the typical hood, which directly affects their exploration characteristics. Mt. Pleasant, included in this section, is a well defined, near vertical breccia pipe. Both the Henderson and Mt. Pleasant discoveries were made by relatively small groups operating independently of the bureaucracy that characterizes large corporations. The management role in each case was one of encouragement. In addition, Wallace had the beneficial experience of working for Climax, whose objective was the discovery of porphyry molybdenum deposits. Henderson was the natural outgrowth of the exploration effort by those who studied and understood the Climax deposit.

Jan 1, 1991

By R. Woods

INTRODUCTION Gaudin (1), considered that "the mechanism of mineral collection is the central problem of flotation theory". From their work on adsorption phenomena in flotation for more than fifty years (2), Gaudin and his co-workers have made major contributions to the elucidation of this mechanism, a fact acknowledged by their contemporaries in the field (e.g. (3)). Their investigations in a number of areas, e. g. demonstrating that submonolayer quantities of adsorbed collector species can induce flotation, or identifying the influence of substances which can activate or depress (1), have helped to provide the basis for and the development of a theory to account for the interaction between mineral and collector. It was established in the late fifties (4) that the presence of oxygen is a prerequisite for the flotation of metal sulfides with thiol collectors. This fact rendered inadequate the concept of simple ion adsorption being responsible for rendering these minerals hydrophobic. The requirement for oxygen has been explained (1) in terms of this species being a component in chemical reactions between the sulfide surface and the collector. Gaudin has been instrumental in identifying the products of chemical reactions at sulfide minerals (1, 5), a line of work which has been continued particularly by Finkelstein and co-workers in South Africa (6). In presenting a detailed mechanism of the mineral-collector- oxygen interaction, it has often been considered that the mineral surface [must] first be oxidized to a metal oxy-sulfur species which

Jan 1, 1976