Search Documents

By M. L. Skow

Large tonnages of the manganese ores found in Aroostook County, Maine, are refractory to conventional mineral-dressing techniques and to the common chemical- extraction procedures. The Maple Mountain-Hovey Mountain ores are typical of this type. Because the most promising method of recovering the manganese from these ores has been a chloridizing roast in which the ground ore is in contact with gaseous hydrogen chloride, preliminary batch tests were made with a fluidized bed. On the basis of these tests, it was concluded that fluidization, with careful control of operating conditions, could be employed for this cloridization and warrants further study. Selective volatilization of the iron at 600° C. was unsuccessful. An operating temperature of approximately 950° C. was necessary for a practicable rate of volatilization of manganese chloride. Hydrogen chloride contents of 10 to 100 percent of the fluidized gas gave essentially equivalent manganese recoveries with an 80- minute retention time, For shorter periods reaction was more complete with the higher hydrogen chloride concentrations. At the 80-minute retention period the lower hydrogen chloride concentrations volatilized somewhat less iron and also improved the physical operation of the process. Fluidization gave results superior to comparable tests on chloridization in a fixed bed.

Jan 1, 1956

By N. Ginouse, S. Reny

"In the mining industry time is critical as production depends on the speed of the mining cycle. During the mining process, the time required to re-open access for the next phase of an underground heading is a key point that strongly depends on the ability of the selected ground support technique to promptly ensure the safety of workers. Fiber reinforced dry-mix shotcrete has been proven to be an efficient and well adapted technique, able to produce a ground support material with the required energy absorption or flexural toughness in a single application phase. In this context, this paper demonstrates the possibility of significantly speeding up the mining process by using a new fiber reinforced dry-mix shotcrete. The new fiber reinforced dry-mix shotcrete is capable of developing flexural toughness in only 24 hours that is equivalent to what is typically achieved after 28 days using current fiber reinforced drymix shotcrete technology.INTRODUCTIONShotcrete is often used for ground support when using the drill and blast method or other tunnelling methods. But before re-opening access for the next phase of the underground heading, the applied shotcrete is required to reach a minimum compressive strength and in case of fiber reinforced shotcrete, a minimum flexural toughness (energy absorption) in order to ensure the safety of the workers going into the heading. Combined with bolts, the use of conventional fiber reinforced shotcrete becomes an interesting method for ground support as it is applied very soon after excavation and works to stabilize ground movements (Bernard E. S., 2009). In this case, the toughness development of fiber reinforced shotcrete becomes an important feature of the material when looking to speedup the mining cycle. However, early re-entry criteria in underground openings are difficult to ascertain as the load carrying capacity of fiber reinforced shotcrete is usually assessed after 7 or 28 days. For this reason, re-entry criteria varies from one mining area to another and are usually based on compressive strength requirements. For example, in northern Ontario, Canada, one of the current practices in the mining industry consists of allowing safe re-entry once fiber reinforced shotcrete has developed a compressive strength of higher than 4 MPa (Dufour, O’Donnell, & Ballou, 2003). Flexural toughness requirements on fiber reinforced shotcrete are also typically based on evaluation after 28 days."

Jan 1, 2015

By Fred D. Wright

This paper describes research at the Bureau of Mines experimental oil-shale mine at Rifle, Colo., to improve blasting techniques and reduce breaking costs. Many of the conclusions are applicable to any mining operation. Experiments Were conducted on many phases of blasting. The effectiveness of various grades of explosives was compared, and several different drill-hole patterns were tried in heading rounds. An experiment was conducted to determine the maximum effective burden for various diameter blast holes. High-speed motion-picture studies were made of blasts, and the time for initial movement of rock after detonation of the explosive was measured. Experiments with millisecond-delay detonators in heading rounds proved that, when used properly, these detonators result in improved fragmentation, economical use of explosive, and compact, easily loaded muck piles.

Jan 1, 1953

By Jian-Xun Fu, Hong-Qiang Liu, Si-Yu Liu

The production of zinc-bearing solid dust is up to 4%~8% of total crude steel in steel plant, which is difficult to be recycled in traditional methods. To fully utilize the resources and reduce environmental pollutions, Chinese steel plants are using rotary hearth furnace (RHF) process to recycle solid dust. A consequential life-cycle inventory was carried out to assess the impact of dust recovery on greenhouse gas emissions based on the local production status. In the study system, the selected steel plant named which have 10.5 million tons of Crude steel productivity and 0.48 million tons solid dust come out meanwhile. To research, a RHF production line of 0.3 million tons directly reduced iron (DRI) a year was established to recycle the solid dust. The DRI will be obtained from RHF and sent to the blast furnace as raw materials to reduce the demand for iron ore and coke in steelmaking processes. By researching on the life-cycle inventory in the system, the steelmaking process with RHF was 2299.3kgCO2/ton steel. It’s a little higher while compared with the process without RHF, which data is 2297.0 kgCO2/ton steel. The small production of DRI make a small difference to reduce the carbon footprint of steelmaking process, the added carbon footprint of RHF process is more than BF and other steelmaking processes reduced. It is concluded that dust recovery has no contribution to the greenhouse gas emission reductions in the technic condition of Chinese steel plants currently.

Jan 1, 2016

By Q Gong, J Li, J Zhao, Y Zheng

Excavation by tunnel boring machines (TBMs) offers many advantages over conventional excavation methods, in terms of safety level, working environment, advance rate and overall cost. While TBMs have been extensively used in civil tunnel construction, they are also viewed as a competitive alternative to the drill-and-blast method for underground mining, attracting increasing attention from the mining industry. This paper presents an overview and general assessment on applications of TBMs in mines, by reviewing more than 60 TBM applications in underground/open pit coal and hard rock mines around the world. The projects range from the early exploratory trials of TBMs in mines in Germany, England, South Africa and America in the 1960s and 1970s, to the ongoing projects in Australia, China and Chile. The paper focuses on the geological compatibilities, the problems encountered, the solutions undertaken and the lessons learned from those projects. The paper summarises the progress made in the past and highlights the challenges faced by TBMs in mining due to complex ground conditions and geometrical requirements. With the technological advances of TBM and experiences gained in the past, more applications of TBMs are expected in underground coal and hard rock mines.CITATION:Zheng, Y, Gong, Q, Li, J and Zhao, J, 2014. A review of the applications of tunnel boring machines in mines, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 691–704 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J-L. Tang

A new rhcoforming processing of Al alloys with component shaping systems apart from slurry preparation systems is experimentally exploited, using the reversible multilevel-speed electromagnetic stirrer, the slurry transfer tool and its coating, the thin plate sample with five steps and rheocasting mould, all of which are independently developed. The results show that semi-solid A356 alloy slurry with shape factor of about 0.85 and particle size of 70~80 µm (under air-cooling condition) could be prepared in 20~25 s, fully meeting the production rate of high pressure die casting. The slurry could be smoothly transferred from the slurry preparation equipment to the rheocasting shot chamber while the slurry temperature of slurry decreases by no more than 3 . The tensile strength and elongation of the semi-solid rheocasting samples could be respectively increased by 11.6~18.2 % and 42.5~50 % compared with the traditional liquid die casting ones, and the rheoforming processing has close affinity with the traditional hot working processes.

Jan 1, 2007

By L. H. McGuire

Many coal beds in the State of Washington, pitching as much as 90°, offer unusual mining conditions. This paper describes methods and safe practices of mechanized mining in pitching bituminous-coal beds that have attracted the attention of mining people from most of the coal-producing countries of the world. The development and use of continuous miners as part of the mechanized program apply particularly to the Roslyn-Cle Elum coalfield, Kittitas County, Wash. All three mines now operating in the field use continuous miners and during 1957 furnished 72 percent of the State's total coal production. Mining operations are now conducted in three coal beds of the Roslyn-Cle Elum field. The coal measures range from 3-1/2 to 20 feet in thickness and vary in dip from 5° to 45° in the localities where the coal is mined. Some safety measures adopted by-the principal operating company in the field during the past 30 years of mechanized mining follow: Use of only permissible electrical or compressed-air-operated equipment on other than intake air; providing and using an explosion gallery to test repaired permissible electrical equipment before taking it underground; use of only compressed-air-operated drill augers in preference to permissible

Jan 1, 1959

By S. Norman Kesten

The Resource Conservation and Recovery Act, commonly known as RCRA, which amends the previous Solid Waste Disposal Act, was signed into law on October 21, 1976. Members of the mining industry began their contacts with EPA in this area two to three years before the Act finally was passed, and that seemed and probably was all to the good. We reviewed and commented upon their studies and in general tried to acquaint them with the peculiarities and the uniqueness of the wastes generated by our industry, of which they were abyssmally ignorant. I suppose we thought that through the bureaucracy we might have some influence upon the provisions of the solid waste legislation that was being bandied about on the hill. Certainly the industry, in general, did very little direct lobbying, as I recall, and there were several reasons for that. For one thing we conceived that the legislation was aimed at the chemical industy and believed that if their people looked after their interests, ours would be safeguarded automatically. Also, the Federal Land Policy and Management Act (FLPMA) was heating up at the same time and, in fact, was signed into law on the same day. In addition, a great deal of lobbying activity was required by amendments of the Clean Air Act and Federal Water Pollution Control Act that were being put together in Congress. These were conceived to be of far greater importance to our industry than a bill to control mostly chemical wastes and, in fact, new bills in both areas became law the following year. Finally, the solid waste bill, RCRA, was patched together by committee staffs over one weekend and was reported out by a conference committee rather hurriedly. Some little goodies about mining were almost after-thoughts in this process.

Jan 1, 1981

By J. M. Janssens, Van Quach Tinh, M. Ruel, R. Leblanc

"Microscopic studies of peat moss indicate a highly porous material. In view of using this natural product as an adsorbing agent for the treatment of polluted water, studies of its adsorbing power for beef extract and alkyl benzene sulphonate solution were determined. The effects of time of contact, particle size, concentration of adsorbent and concentration of pollutant were studied. In the case of beef extract, there is a COD reduction of around 27 per cent; in the case of the alkyl benzene sulphonate, the percentage reduction varied from 72 to 95 per cent. A water treatment plant based on the adsorbing power of peat moss with simultaneous recuperation of the pollutant is proposed."

Jan 1, 1971

By Giles D, Wegmann D

The Mt Todd Gold Project is located 42 km northwest of the township of Katherine within the Northern Territory of Australia. It is situated in the southeastern portion of the Pine Creek Geosyncline. The Batman gold deposit, the largest of several deposits at Mt Todd, hosts an identified mineral resource of 92.9 million tonnes (Mt) grading 1.4 grams/tonne (g/t) as at 31 December 1993. Host rocks at Batman are assigned to the Early Proterozoic Burrell Creek Formation, comprising greywacke and siltstone interbedded with shale. Gold mineralisation is associated with a very broad zone of sheeted and stockwork quartz-sulphide veins that occupy a corridor of intense brittle fracture and faulting. A conceptual model of formation involves the dilation of joints and micro-faults within overlying sediments during sinistral movement along a basement shear zone. Synchronous granite intrusion generated convective circulation of crustal fluids through the sedimentary pile resulting in the formation of auriferous quartz veins within favourable structures. The Batman zone of mineralisation is not directly related to fold structures which typify several other major gold deposits within the Pine Creek Geosyncline.

Jan 1, 1994

By S. W. Marcuson, P. J. Mackey

The Canadian non-ferrous mining and metallurgical industry has made great strides in environmental protection during the past half century. The path taken by the copper-nickel smelting industry in reaching today’s level is traced in this paper. Following the practice at early copper smelters in Wales and in the US, Canadian smelters originally used tall stacks to disperse furnace of-gases. This was the normal mode of operation and was accepted by society and by Government. Gradually, Government regulations required fixation of sulphur dioxide emissions and Canadian companies responded with significant technical developments to achieve this result. The initial development in Canada of the first new technologies such as the Cominco Flash Suspension Roaster and the Freeman Flash Smelting Process - both representing early versions of the modern established flash smelting technologies - and then later technologies such as the Inco Flash Smelting Process and the Noranda Process, both of which continue to this day, are discussed in this paper in terms of their contributions to the development of environmentally friendly plants. The evolution of these and other technologies is also discussed. Some comments regarding how the industry will face the future are also included.

Jan 1, 2015

Jan 1, 1886

By R. C. Diehl

Coal, fly ash, and flue gas samples were analyzed for mercury (Hg) by double gold amalgamation-flameless atomic absorption spectrophotometry. The purpose of the study was to elucidate the fate of the trace mercury in the coal when the coal is burned. Samples were collected from a bench-scale 100-g/hr combustor, a 500-lb/hr combustor, and three coal-burning powerplants. In all cases mercury was found in the fly ash. The amounts ranged from about 9 to about 70 percent of the mercury in the coal that was burned.

Jan 1, 1972

By B. Larsen

The Søderberg electrode was invented about 95 years ago by the company Elektrokjemisk, later known as ELKEM. It is still the most commonly used electrode system in submerged-arc furnaces for ferroalloys, platinum smelting, and slag cleaning operations. The size of the furnaces and electrodes has increased over the years and electrode diameters up to 2000 mm are today in use. Such large electrodes can be challenging to manage, and large electrodes are also more demanding when it comes to the electrode paste used in the electrodes. Although electrode sizes and equipment around the electrodes have changed, the main principles of the Søderberg electrode processes are the same. To assists in proper understanding of the electrode processes and to optimize electrode management, Elkem has developed several mathematical tools covering various aspect of the process. Both temperatures and thermal stresses can be calculated during dynamic conditions. The paper demonstrates, with examples, how the tools are used in both education and as practical input to improved electrode performance.

Jan 1, 2012

By Robert Shaw

"The paper point out the volcanogene and sediment-hosted base metal deposit from the Colombian cordilleras have been considered in the light of tectonogenic models for these deposit types, based upon the recent re-interpretation of the geology and tectonic assembly of the Northern Andean Block by Cediel and Cáceres and Cediel. Numerous distinct propitious metallogenic settings containing important but subexploredbase metal mineralisation are manifest as a result of the tectonic evolution of this northern-most sector of the Andes. Some examples include like a) Central African Cu (U) Belt - type mineralisation within the back-arc region of the early– middle Paleozoic Cordillerantype Quetame Orogeny, b) numerous SEDEX and Sediment-Hosted Zn (Pb-Ag) and Cu (Ag) styles of mineralisation associated with various phases of continental and continental margin rifting during the late Paleozoic to Mesozoic Bolívar Aulacogen, and c) various Cu-Zn-Pb (Au, Ag) Volcanogene Massive Sulphide manifestations associated with intra-oceanic magmatic arc development and accretionary tectonics during the Meso-Cenozoic Northern Andean Orogeny. "

Apr 22, 2003

By D. J. MacDonald

As part of a U.S. Bureau of Mines program seeking improvements to the Bayer process, a typical Jamaican bauxite was heated at temperatures up to 500° C in hydrogen, and its leachability under Bayer process conditions was measured and properties of its leached residue were observed. The objectives were to find ways to decrease the amount of organic carbon in bauxite or in leach liquor derived from it without impairing its leachability, and to improve the leached residue's filterability. Techniques employed included heating bauxite under pressure in an autoclave with hydrogen, and in flowing hydrogen at ambient pressure in a tube furnace. Leaching tests were done with a 600-mL stirred reactor. In some of the leaching tests, ferrous sulfate (FeS04) was introduced before leaching to produce a partially magnetic product. Results showed that exposure to hydrogen at temperatures from 160° to 360° C progressively diminished the bauxite's content of organic carbon and decreased the ratio of organic carbon to aluminum in leach liquor, an improvement that would allow a process using hydrogen-treated bauxite to be operated at a smaller recycle ratio, thereby consuming less energy and allowing greater throughput for a plant of given capacity. The bauxite's leachability was not impaired by high-temperature pretreatments, except at temperatures higher than 280° C. Pretreatments in hydrogen produced black, partially reduced bauxite which upon leaching gave a residue that was attracted to a magnetic field and was amenable to separation from green liquor by a magnetic filtration method.

Jan 1, 2010

By W. I. Nelson

This paper describing the mining practices at the Engels mine is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Engels Copper Mining Co. operates two mines about 3 miles apart in Plumas County. Calif. Both mines send ore to the same mill, and the methods of the larger, or Engels mine, are described in this paper. Between 800 and 1,000 tons of 1-3/4 to 2-1/2 per cent copper ore are mined daily from this mine by a shrinkage method. Connection is made with the Western Pacific Railroad at Paxton by the Indian Valley Railroad, which is 22 miles long and operates a daily mixed train to the mine.

Jan 1, 1930

By P Guj, J A. Bell

The valuation of early-stage exploration projects requires a valuer to take into account a large number of uncertain value drivers, the interplay among which may be non-linear. This paper examines some of the key value drivers including geology, target metrics, project area and maturity, the market and the psychology behind the decision-making process. The commonly accepted valuation methods and their underlying logic are outlined, including a view on why they evolved, what value drivers they attempt to address and their potential shortcomings. These methods include the multiple of exploration expenditure, geoscience rating, expected values and market based methods. The potential future valuation methods of replacement values and neural networks are also introduced along with how to minimise heuristic bias and error within the market-based approach.CITATION:Bell, J A and Guj, P, 2012. Exploration value drivers and methodologies, in Proceedings Project Evaluation 2012 , pp 17-28 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By Andressa Alves da Silva

Nowadays, population growth and the interest of food industry, makes the research and applications of biodegradable polymers increase, because under favorable conditions its degradations may occur within weeks or in a few months, reducing the environmental impact. This work presents the processing and characterization of flexible films by the incorporation of 3 % (% wt) of modified bentonite light green clay in the Copolyester/PLA biodegradable blend. The clay incorporation was carried out by melt-mixing processing, using a twin screw extruder machine. The films were obtained by cast extrusion tape. The films obtained were submitted to tensile tests, SEM and XRD analysis, and the correlation between their properties was discussed. The XRD results of clay showed that the quaternary salt and sodium carbonate addition increased the interlayer distance of clay making it easier to intercalation of blend in the nanoclay. The XRD results of PBAT/PLA/Clay nanocomposite show no characteristic organoclay peaks. This result suggests intercalation between nanoclay and matrix (blend). The tensile test results showed an increase of around 30% in tensile strength at break of nanocomposite film when compared with blend film.

Aug 8, 2018

By N Gupta, R Trivedi, S Bhandari

Managing blasting operations in four mines surrounded by villages is a challenging task. This study aims to compare the blast-induced flyrock as observed in opencast mines by predicting flyrock distance using a soft computing approach known as an adaptive neuro-fuzzy inference system (ANFIS) and Flyrock Predictor software based on empirical studies. Blast design and geotechnical variables such as linear charge concentration, burden, stemming length, specific charge, unconfined compressive strength and rock quality designation were selected as independent variables, while flyrock distance was used as a dependent variable. Out of 120 blasts, data from 100 blasts was used to train and test the ANFIS model. Flyrock distance for the remaining 20 blasts was used to evaluate the model. Flyrock distance has also been predicted using Flyrock Predictor software based on an empirical approach using the same data sets as those used for ANFIS. Performance indices like root mean square error (RMSE), mean absolute error and coefficient of determination (R2) were evaluated to compare the reliability of ANFIS and Flyrock Predictor quantitatively. ANFIS was found to be a better predictive tool, with 1.75 m RMSE and 0.966 R2 compared to Flyrock Predictor, which returned RMSE and R2 values of 2.48 m and 0.932 respectively.CITATION:Trivedi, R, Singh, T N, Gupta, N and Bhandari, S, 2015. Soft computing approach to predict blast-induced flyrock, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 455–462 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015