Search Documents

By A. Eslami, H. Tabatabaei, M. Kolandoozan, Z. Manafi, A. R. Shahverdi, M. Noaparast, M. Oliazadeh

Application of Acidithiobacillus ferrooxidans bacteria to flotation of Sarcheshmeh low-grade copper sulphide ore was studied. Sarcheshmeh low-grade ore contains pyrite, which causes some problems in the flotation of copper minerals. In this study, A. ferrooxidans was used to change the surface chemistry of pyrite and copper sulphide ores and consequently, their flotation behaviour. In the presence of A. ferrooxidans and xanthate as a collector, pyrite was depressed whereas chalcopyrite and other sulphide minerals were unaffected. In addition, the pulp pH remained unchanged. It was shown that the surface chemical properties of the bacteria can be manipulated successfully to achieve the desired effects in a flotation process. The results showed that the recovery of pyrite in the presence of the bio-depressant is 50% lower than when no bacteria were present. At the same time the recovery of chalcopyrite remained unchanged.

Jan 1, 2004

By G. T. Lineberry, R. Q. Honaker

Coal extraction typically results in the recovery of pure rock that ranges from small to very large quantities depending on seam thickness and other characteristics. The removal of pure rock may allow the recovery of three times the amount in middling coal particles, which has significant economical benefits. In an industrial example, a 150% increase in revenue was realized from deshaling a low-ash, run-of-mine coal and blending with a processed clean coal product. Deshaling is the process of removing pure rock from coal, which normally involves a high-density separation in a gravity-based process. The removal of the relatively pure rock near the point of extraction has the potential to further enhance the economics of an operation due to reduced materials handling and refuse storage costs.

Jan 1, 2004

By C. H. Mathewson

THIS paper was prepared upon request as a contribution to a symposium covering the manufacture, properties, and uses of the important non-ferrous metals. In approaching a subject as broad as this, there is a natural desire to build up a comprehensive and finished production which shall constitute a dependable source of information on all questions properly belonging to this branch of metal technology. There are, however, a number of circumstances, apart from the mere routine of labor and thought involved, which operate rather effectively against the possibility of completing such an ambitious program at the present time. First of all, as far as any public record of results is concerned, the commercial rolling, drawing, and forming of zinc with relation to changes of structure and properties-and this we consider to constitute the elements of metal technology-might as well be an unpractised art. We have never seen a published photomicrograph showing the structural characteristics of either hard or soft sheet or strip, although the structure of castings has been frequently described, and other coarse-grained structures resulting from hard-hammering and annealing have been reproduced. Thus, an author in this field must proceed to his task without much assistance from the literature, and the outcome can represent only a personal estimate of principles, facts, or findings, and not a summary

Jan 9, 1919

By L. P. Durham

DuRing the early mine development period, 1929 and the first part of 1930, a 300-ton pilot-plant concentrator was built at Nkana mine of the Rhokana Corporation, Northern Rhodesia. This plant operated from May 26, 1930 until Oct. 26, 1931, treating 101,080 tons of Nkana ores and producing 4372 tons of concentrate. The plant was built, primarily, as a test unit to determine the grinding characteristics, floatability, etc. of the Nkana ores and other ores of the Rhodesian copper belt and to supply sufficient data on which to base the design of a 5000-ton concentrating plant at Nkana mine. The test unit operated wholly on development ores and no attempt was made to grade or select the ores from any section of the mine. The average assays for the 17 months of operation are given in Table 1. The first ground was broken for the 5000-ton concentrator during June, 1930, and the construction of the plant was completed in November, 1931. The plant started on Dec. 10 and has operated continuously since that date: The whole of the concentrating plant is compact and closely connected, yet with sufficient space for expansion of all sections up to 20,000 to 25,000 tons per day capacity. Mining operations are carried on along a length of about four miles on the easterly limb of the Nkana syncline. This length includes the North orebody, from which all production has thus far originated, and the Mindola orebody, now being developed for production. The ore-bearing measures in the North orebody are leached for some 75 ft. below the surface; the oxidized zone varies in vertical extent from 100 to 150 ft. Practically all the ore below the 200-ft. level is sufficiently

Jan 1, 1935

The aim of this paper is to examine the problems confronting the planner, designer, constructor and management when rehabilitating the works associated with road building- and including quarry and borrow areas. The importance of further investigation into the many factors involved, including species, methods of planting and aftercare is stressed as is the need for trained personnel and the consequential availability of specialised training courses. Emphasis is placed upon the relevance of a rational and unemotional approach to rehabilitation with respect to the landscape and to the high degree of co-ordination and co-operation between all disciplines involved.

Jan 1, 1976

By William E. Ford, Edward Salisbury Dana

1. Normal Class (28) Gypsum Type 2. Hemimorphic Class (29) Tartaric Acid Type 3. Clinohedral Class (30) Clinohedrite Type Mathematical Relations of the Monoclinic System Crystallographic Axes. - The monoetinic system includes all the forms which are referred to three unequal axes, having one of their axial inclinations oblique. The axes are designated as follows : the inclined or clino-axis is a; the ortho-axis is b, the vertical axis is c. The acute angle between the axes a and c is represented by the letter 0; the angles between a and b and b and c are right angles. See Fig. 331.

Jan 1, 1922

This address is set deliberately in the broadest possible terms. A review of the place of mining in Australian life today will serve to point up the changes that we can see in the life of people in the industry. Some of the influences on the future welfare of mining people bear also on the progress of this Institute, now approaching its 90th year. As mining becomes more and more dependent on higher technology and therefore, on the higher skills of the people in the industry, the role of The Institute, I suggest, becomes more and more significant.With investment per employee in mining generally continuing to rise, our ability to handle problems of manpower and human relations becomes a matter of greater importance.Questions that flow from these general thoughts form the substance of what I have to say.

Jan 1, 1982

By H. W. Glen

In the hope of finding out what the readers of the SAIMM Journal want of our Journal, we sent out a questionnaire with the October 1979 issue. The 2500 copies of the questionnaire sent out elicited 228 responses, which represents a return of 8,8 per cent. The number of responses received from overseas was 24, i.e., approximately 10 per cent of the total. The following is an analysis of the responses received.

Jan 1, 1980

By M. -A. de Ville d’Avray, J. Bosman, S. Brochot

Dense Medium Separation (DMS) technologies are used for light (coal, lithium) or heavy (chromite, iron ore, diamonds) minerals concentration, but also for ore pre-concentration (Pb/Zn) or waste (plastics). Dense media are mainly formed from a suspension of magnetite or ferrosilicon in water. Such DMS circuit design or optimisation requires a full and detailed material balance which can be obtained by the aid of modelling and simulation tools. This balance is not limited to ore and its valuable minerals, but also the recovery of the dense medium itself. If the density is the main property used for separation, the particle size plays a non-negligible role, and, more precisely, the liberation classes which can be associated to the washability curve. The paper presents how the modelling and simulation platform USIM PAC can answer this challenge with the set of models for DMS operating units such as drums or cyclones, and their associated screens (drainage, rinsing) and magnetic separators for medium recovery. Some examples for mineral concentration will illustrate this approach. Keywords: Process simulation, process modelling, dense medium separation, process optimisation

Jan 1, 2020

By R. D. Brown

Ever since British Columbia started the ball rolling in 1974 with the introduction of its now-defunct Mineral Royalties Act, all Canada's resource-based provinces have significantly altered their mining tax systems. The last resource-based province to abandon its pre -1974 mining tax structure is New Brunswick, which introduced a new mining tax regime in the summer of 1977 to take effect from April 1 1977. The new structure, which represents the outcome of considerable study and discussions with industry representatives, contains some intriguing concepts which make Nero Brunswick's new mining tax system unique among the Canadian provinces.

Jan 1, 1977

The nickel operations at Kambalda consist of mining thin massive to disseminated Ni sulphide orebodies from 10 individual mines of variable grade.Daily sampling involves visual estimation of the grade of working faces based on geological parameters. This system of grade estimation is used as a guide for daily grade control only.Nickel metal allocation is based on an external sampling system. As all ore sources are blended at the primary crusher, only one calculated mill head grade is available. Therefore all sources are sampled prior to crushing. This system historically consisted of mechanically grab sampling ore from trucks as they passed over a weighbridge on arrival at the concentrator. Currently the system involves diverting one out of every ten trucks to its mine sample stockpile, which is crushed through the primary, secondary and tertiary crushing system fortnightly. The individual mine grades are re-combined to create a total sample grade. This is reconciled against the calculated mill head grade. The reconciliation factor is applied uniformly to all individual mine sample grades to calculate mill reconciled mine grades.

Jan 1, 1990

By N. E. Garner

Laboratory experiments were conducted to investigate the cutting of a single diamond on limestone and shale under simulated down-hole conditions. A high-pressure chamber was modified by adding a rock-rotating device so that planing tests could be run. Weight on the diamond, diamond geometry and differential pressure across the face of the rock were varied. It was found that (I) high differential pressure reduced the volume of rock cut by the diamond at a given bit weight by strengthening the rock and changing the mode of failure; (2) a finely powdered rock left in the bottom of the grooves reduced the volume cut by as much as 50 percent; and (3) orientation of a single diamond about the axis of a drill point had considerable influence on diamond cutting efficiency. INTRODUCTION Diamond bits consist of many diamonds held in a matrix provided with water courses for fluid passage to clean, cool and lubricate the diamonds as they drill formation. Each diamond contributes its share to the overall effectiveness of a bit, but a lack of understanding of the performance of a single diamond has hampered efforts to engineer improvements in diamond bits. The need for those improvements prompted this study. This paper describes the findings of a laboratory investigation of the outting action of a single diamond where the differential pressure between the wdlbore and formation, diamond geometry and vertical force on the diamond were independently varied. The tests were conducted in a pressure chamber that provided relative horizontal motion (planing) between a rock and diamond under simulated down-hole pressure conditions. EQUIPMENT HIGH-PRESSURE CHAMBER WITH ROTATING DEVICE The high-pressure chamber used in previous rock mechanics studies' was modified for this study by addition of a rock-rotating device. The modified chamber (Fig. 1) differs from the old chamber in that the rock can be rotated to provide relative horizontal movement between the rock and the penetrator which may be a small element of a diamond or a drag bit. In this study the penetrator was a single diamond. The rock sample holder inside the chamber is mounted on a thrust bearing and is connected to the external drive mechanism by a stem that passes through two seal elements. The seal elements are needed to allow formation pressure to enter the bottom of the rock sample through a small hole in the stem. The Kapseal seal elements (Tefion boots backed by O-rings) provide low friction (hand free) even at differentials of 5,000 psi. The drive mechanism is a variable-speed transmission with a speed range from 0 to 30 rpm and an output torque of 2,800 in.-lb. A right-angle-drive gear box couples the drive to the stem. The new design has two independent pressure systems (formation and borehole) to simulate down-hole rock stress environment. Formation pressure enters from the bottom of the rock through a 6-in. diameter area, and borehole pressure acts over the remaining surface. A 14-in. layer of zero fluid loss oil-base mud poured over the top of the rock and an O-ring seal on bottom allow a differential between the borehole and formation pressures. Bayol 50 was used as the hydraulic fluid in the chamber. The differentials reported here were obtained by elevating the borehole pressure while keeping the formation pressure at zero.

By K. R. Price, M. Gauna

A high seam geologic condition exists at Jim Walter Resources No. 4 mine that requires immediate rib support after a continuous miner cuts a place. High seam mining heights are typically 2.4 to 2.6 m (8 to 9 ft) and a thick rock layer is present in the upper portion of the coal rib side. The 610-m (2000 ft) mining depth at No. 4 mine induces horizontal rib line movement after excavating an entry. Horizontal rib movement greater than 305 mm (12 in.) have been noted. When lateral movement occurs in the high seam areas, the thick rock layer, and the coal above the rock layer, become fractured and tend to roll into the entry. If not adequately supported, large rib rolls develop in the place being bolted as well as in previously mined areas that endanger men and equipment. To control this, rib support must be installed in the roof bolting operation as the bolting crew works toward the face. A rib control system has been developed for this high seam mining condition using a mechanical anchor bolt placed at an angle in the rib and installed with a modified Fletcher DDM-15 bolting machine. More than 120 km (75 miles) of entry have been supported with angle rib bolts. These angle bolts constitute 43% to 60% of the total roof and rib bolt footage in the high seam portions of No. 4 mine. The angle rib bolting system has proven safer, more effective, and more efficient than the earlier support method using bolts installed horizontally into the rib. No rib roll accidents have occurred since the angle drill bolting machines were placed in service in 1981. By securing the broken rib material with an angle bolt anchored above the coal pillar, a more effective means of rib control is achieved. Angle rib bolting does not interfere with continuous miner productivity. In addition, bolting crews are now reduced from three to two people. Total drilling supply costs are about 60% the previous cost, when compared to the previous support method using horizontal rib bolts:

Jan 1, 1985

By Dale C. Matthews

The Getchell Gold Hine is located about 40 miles northeast of Winnemucca, Nevada. Gold was discovered at the mine in 1934 and production was started in 1938 and ended in 1967 for its first phase of operation. Gold production during this period was about 800,000 ounces. In 1983, FirstHiss Gold Inc. purchased the property and initiated an exploration program that proved minable reserves of about 1,300,000 ounces of gold remained in the mine. During the exploration period, metallurgical testing was conducted to determine the most economical process that could be utilized for recovery of gold from the very refractory ore. After extensive investigation, pressure oxidation of the ore was selected, Engineering for the new plant commenced in 1987 and construction was completed in 1989 at a cost of about $87,400,000.00, not including financing cost.

Jan 1, 1990

This research contributes to BioMinE (http://biomine.brgm.fr), an integrated European Union project of the Sixth Framework Programme. The general objective of BioMinE is the development and integration of innovative, environmentally friendly, biohydrometallurgical processes for the recovery of metals from primary and secondary resources within Europe. The work presented in this paper deals with the initial plan of study on the sustainable use of solid wastes derived from bio-processing of European metal bearing resources. The approach involves solidifying the waste into cementitious waste composites analogous to controlled low-strength materials (CLSM). The aim is to achieve composites of adequate mechanical, physicochemical and environmental integrity, thus providing a sustainable solution for dealing with such bulk products which are conventionally unmarketable and therefore normally discarded to landfill. Assessment has been based on largely ?model? wastes anticipated to be similar to bio-processing wastes. These include an ochreous mine water sludge and an industrial goethite residue. The work indicates that wastes containing high iron and calcium contents, typical of products from bioleaching of concentrates, could be beneficially reformed as CLSM of appropriate compressive strength. Due to the high water contents of these composites, porosity and hydraulic conductivity were correspondingly high. Flow-through leach tests showed some resistance to immobilisation of toxic elements. Work is continuing to reduce the risk of toxic elements leaching under environmental conditions. This will include laboratory-scale encapsulated systems of CLSM, designed and tested to produce a novel type of engineered fill structure.

Jan 1, 2006

By Julian Nardi

Pumping solids through a pipeline is not new but until very recently other means of transportation were cheaper. Many proposed pipelines for transporting solids, while technically feasible, have not been attractive enough to warrant the financial risk involved. In some instances, the difference in transportation cost was negligible. In others, the threat of pipeline competition resulted in a slashing of rates on existing transportation to the point where a pipeline could no longer be justified. In others, a competitive product was cheaper. FIRST IN PLACERS The earliest record of solids being transported in a pipe was in the late 1850s in California placer mines. Water under pressure was used to force gold-bearing gravel up through a pipe, from 30 to as much as 55 ft, to a point where it could be discharged into a flume or sluice.

Jan 9, 1959

By Des Bolton

With the introduction of Cast Blasting techniques, field controls of Drilling & Blasting operations became more important. New drills were purchased which were equipped with sophisticated instrumentation and more accurate drilling plans were required. Concurrently a decision had to be made on the replacement of borehole logging equipment owned by the mine. The use of a contractor to log blast boreholes was eventually decided upon, the information gained from this operation is used in the short-term drill and blast planning and may also be used to assist in the coaling operation if density I quality correlations prove acceptable.

Jan 1, 1994

By Ahmed M. Nofal

This article reviews some important characteristics of the known Egyptian phosphate deposits, such as mining conditions, transport criteria, quality of products affecting their export markets and utilisation in fertilizers industry. Special attention will be given to the newly discovered large deposit of Abu-Tartur with some billion tons of ore reserves. A big project is now under implementation on Abu-Tartur deposit where the long-wall method of underground mining will be applied and a flow sheet of beneficiation will be in operation including a particular feature nontraditional in phosphate processing: high-intensity magnetic separation to eliminate dolomite impurities. Comparison with some international phosphates will be tried in order to trace the situation of Egyptian phosphates in the world market.

Jan 1, 1993

By Holbrook G. Botset

Experiments performed in this laboratory on the flow of gas-liquid mixtures through unconsolidated sands have been described and discussed in an earlier paper.4 In these earlier experiments a definite relationship was found between the liquid saturation of a sand and its permeability to the liquid or gas phase. Furthermore, the nature of the sand, the permeabilities of the sands over a range between 17 and 260 darcies, appeared to have a negligible effect upon the saturation-permeability relation. Likewise experiments indicated that the viscosity of the liquid, or the substitution of an immiscible liquid for the gas phase, had only a very slight effect on the permeability-saturation relation. This conclusion has since been definitely confirmed by the experiments of M. C. Leverett3 on the flow of oil and water through unconsolidated sands. The sands used by Leverett were of very low permeability (between 6.8 and 1.04 darcies), while the oil-water viscosity ratio varied between 90 and 0.057. Since the sands that constitute petroleum reservoirs are largely consolidated, although of widely varying degrees of consolidation, it was desirable to extend the experiments on gas-liquid mixtures to consolidated sand. In the study of consolidated sands additional variables are involved, but for the initial experiments the only new variable to be introduced was the cementing material. Experimental Procedure A comparatively limited assortment of sandstones was available for the selection of the experimental material. Of these, the Nichols buff sandstone appeared to be most suitable. It gives no visual evidence of any bedding planes, it has a firm structure, permitting easy handling, and its permeability is about 0.5 darcy. Its only disadvantage is the fact that it contains an appreciable amount of ferric oxide which, for experiments involving water, will hydrate and reduce the permeability. This

Jan 1, 1940

By Holbrook G. Botset

Experiments performed in this laboratory on the flow of gas-liquid mixtures through unconsolidated sands have been described and discussed in an earlier paper.4 In these earlier experiments a definite relationship was found between the liquid saturation of a sand and its permeability to the liquid or gas phase. Furthermore, the nature of the sand, the permeabilities of the sands over a range between 17 and 260 darcies, appeared to have a negligible effect upon the saturation-permeability relation. Likewise experiments indicated that the viscosity of the liquid, or the substitution of an immiscible liquid for the gas phase, had only a very slight effect on the permeability-saturation relation. This conclusion has since been definitely confirmed by the experiments of M. C. Leverett3 on the flow of oil and water through unconsolidated sands. The sands used by Leverett were of very low permeability (between 6.8 and 1.04 darcies), while the oil-water viscosity ratio varied between 90 and 0.057. Since the sands that constitute petroleum reservoirs are largely consolidated, although of widely varying degrees of consolidation, it was desirable to extend the experiments on gas-liquid mixtures to consolidated sand. In the study of consolidated sands additional variables are involved, but for the initial experiments the only new variable to be introduced was the cementing material. Experimental Procedure A comparatively limited assortment of sandstones was available for the selection of the experimental material. Of these, the Nichols buff sandstone appeared to be most suitable. It gives no visual evidence of any bedding planes, it has a firm structure, permitting easy handling, and its permeability is about 0.5 darcy. Its only disadvantage is the fact that it contains an appreciable amount of ferric oxide which, for experiments involving water, will hydrate and reduce the permeability. This

Jan 1, 1940