Search Documents

By I. R. McGowan, J. Tilk, J. I. Hershman, R. L. Lewis

The White Pine Mine is a large underground copper mine located in the Upper Peninsula of Michigan. A numerical ground water flow model of the White Pine Mine was constructed to evaluate potential engineering controls that would reduce the rate of mine-water discharge after closure. Of the passive controls evaluated, the placement of bulkheads within the mine workings was predicted to offer the greatest benefit, reducing the rate of discharge by as much as 35%.

Jan 1, 1998

By R. L. Lewis

The White Pine Mine is a large underground copper mine located in the Upper Peninsula of Michigan. A numerical ground water flow model of the White Pine Mine was constructed to evaluate potential engineering controls that would reduce the rate of mine-water discharge after closure. Of the passive controls evaluated, the placement of bulkheads within the mine workings was predicted to offer the greatest benefit, reducing the rate of discharge by as much as 35%.

Jan 1, 1997

By Walter Harvey Weed

(Mexican Meeting, November, 1901.) Among the many causes of that perplexing featurc of mineexploitation, the unequal distribution of the ore, the influence of the country-rock upon the vein-contents has long beer1 accepted as an important factor in certain districts, but the general application of the theory has not been proved. It is now possible to obtain trustworthy data with which to test the theory, and either to confirm or to overthrow this time-honored

Jan 1, 1902

By R. C. Mahon

THE Homer iron-ore mine is at Iron River, Mich. Because it covers a large area, 400 acres, and because there was a considerable depth of water in the glacial drift above most of the ore bodies, this mine has presented a number of unusual and often difficult operational problems. The purpose of this paper is to discuss a few of the most important problems encountered. SURFACE WATER Mining on this property was started on one 40-acre tract. The ledge in this area was the highest on the property and, although it was a real problem, water could be handled by underground pumping. During the first period of mining, drifts were driven just under the ledge and holes were drilled through to the surface material. In later years these drifts have been extended wherever possible. Although these drifts assisted in the drainage problem, it was evident they would not be sufficient alone. Before mining on a large scale could be started on this property, the water problem had to be solved. A number of test holes were put down to the ledge, and showed that there was an average 150 ft. of water-saturated glacial drift above the ledge over the rest of the mine. The upper 70 ft. was gravel and sand and the lower 80 ft. clay and hard pan, with some narrow seams of sand and gravel. It was evident that the water above the clay seam could not be drained off through openings in the ledge and for that reason it was decided to install surface drainage wells. This method of drainage was entirely new at that time and was pioneered at the Homer mine. The sinking of the first well was started in June 1929. Immediately following the first well a number of wells were sunk, but only to the top of the clay seam. This was done with the idea that a greater capacity could be obtained in a shorter time from gravel seams where the water flowed more freely and that the cost of pumping the water above the clay seam would be considerably less than if the wells had all been sunk to the ledge at once. Before the drainage of surface water was started, 1200 gal. per min. against a head of 800 ft. was being pumped from the mine. By March of 1932, with five surface wells in operation, the mine pumping had been reduced to 150 gal. per min. At this time we were pumping 5000 gal. per min., under an average head of 110 ft. from the surface wells. The total pumping costs were 30 per cent less than in 1929 because the greater capacity was being pumped at a much lower head. From 1932 to 1936 the mine was idle and all surface pumping was stopped. Since 1936, 10 new wells have been added with a total pumping capacity of 8000 gal. per min. at the present time. The water level has been lowered 70 ft. since surface pumping was started in 1929, and it is now approximately at the top of the clay. To remove the water below the clay seam, 11 of the 15 wells were sunk to the ledge.

Jan 1, 1945

By R. C. Mahon

The Homer iron-ore mine is at Iron River, Mich. Because it covers a large area, 400 acres, and because there was a considerable depth of water in the glacial drift above most of the ore bodies, this mine has presented a number of unusual and often difficult operational problems. The purpose of this paper is to discuss a few of the most important problems encountered. Surface Water Mining on this property was started on one 40-acre tract. The ledge in this area was the highest on the property and, although it was a real problem, water could be handled by underground pumping. During the first period of mining, drifts were driven just under the ledge and holes were drilled through to the surface material. In later years these drifts have been extended wherever possible. Although these drifts assisted in the drainage problem, it was evident they would not be sufficient alone. Before mining on a large scale could be started on this property, the water problem had to be solved. A number of test holes were put down to the ledge, and showed that there was an average 150 ft. of water-saturated glacial drift above the ledge over the rest of the mine. The upper 70 ft. was gravel and sand and the lower 80 ft. clay and hard pan, with some narrow seams of sand and gravel. It was evident that the water above the clay seam could not be drained off through openings in the ledge and for that reason it was decided to install surface drainage wells. This method of drainage was entirely new at that time and was pioneered at the Homer mine. The sinking of the first well was started in June 1929. Immediately following the first well a number of wells were sunk, but only to the top of the clay seam. This was done with the idea that a greater capacity could be obtained in a shorter time from gravel seams where the water flowed more freely and that the cost of pumping the water above the clay seam would be considerably less than if the wells had all been sunk to the ledge at once. Before the drainage of surface water was started, 1200 gal. per min. against a head of 800 ft. was being pumped from the mine. By March of 1932, with five surface wells in operation, the mine pumping had been reduced to 150 gal. per min. At this time we were pumping 5000 gal. per min., under an average head of 110 ft. from the surface wells. The total pumping costs were 30 per cent less than in 1929 because the greater capacity was being pumped at a much lower head. From 1932 to 1936 the mine was idle and all surface pumping was stopped. Since 1936, 10 new wells have been added with a total pumping capacity of 8000 gal. per min. at the present time. The water level has been lowered 70 ft. since surface pumping was started in 1929, and it is now approximately at the top of the clay. To remove the water below the clay seam, 11 of the 15 wells were sunk to the ledge.

Jan 1, 1946

By P. Davies

The Hillside Smelter presently under construction at Richards Bay, Republic of South Africa, will be, on completion, the fifth largest aluminium smelter in the world. The site selected for this plant is underlain by sandy soils of variable density to depths of 30m or greater. In order to firmly establish pile founding depths required for alternative pile types in the variable subsurface conditions prevailing across the site, a pre-construction test piling programme was conducted incorporating piles instrumented with resistance strain gauges. The results allowed analysis of the relative contributions of end-bearing and shaft friction to the overall bearing capacity of each pile type and permitted comparison with the predictions of conventional static bearing capacity analyses. Conformance with acceptance criteria in respect of allowable pile head movements for single piles was also examined.

Jan 1, 1996

By P Wapner, C Lo Edwards, S CO Schmidt, J N. Johnson, R Oliver

Shale oil recovery rates that can be achieved in underground in situ retorts can be strongly influenced by the shale breakage and fragment-size distribution achieved during rubblization. Since the fragmentation pattern in the retort is a direct result of the blast design used for rubblization, the characterizing blast parameters should be carefully selected. Explosives should be matched to the host material and blast geometries properly chosen so that the required fragmentation results are achieved at optimum costs. Special attention must be directed to selecting blast parameters that produce uniform bed permeability, suppression of fines, proper fragment size distribution, and minimal damage to the retort walls and ceiling. The influence of joints and natural fractures should also be known. In instances where the requisite blasting parameters are unknown, they should be determined from test blasts.

Jan 1, 1979

Cable bolts have been used extensively in the development of the footwall of the Mt Whaleback Mine as a part of the ground improvement program since 1986. High tensile seven wire stress relieved steel strand similar to that used in pre-stressed concrete and grouted in place with sulphate resistant cement have been employed for rock-mass reinforcement.Most of the footwall is developed in Mt McRae Shale which contains a 20 m thick pyritic shale layer 14 m below the ore/waste contact. Due to extensive folding of the footwall rocks, the pyritic shale layer regularly occurs on, or close to the pit slope. Rain water run-off seeping through pyritic shale becomes acidic to the extent where its pH value can be as low as 1.5.

Jan 1, 1992

By S J. Chen, N Jiang, Y S. Ding, F X. Li, D W. Yin, F Wang

This study assessed the deformation failure characteristics of rock-coal composites with different height ratios. Uniaxial compression tests were conducted using an acoustic emission monitoring system and XTDIC three-dimensional full-field strain measurement system. The results showed that with the increase in rock-coal height ratios, the uniaxial compressive strength of composite samples increased from 5.26 MPa to 14.61 MPa. The evolution of the deformation localisation zone of the composite samples is closely related to the initiation and propagation of the primary cracks in the coal samples. At the moment when the main fracture of the coal samples occurs, there is a large drop after the peak of the stress-strain curve of the composite samples, and the height of the rock samples increased to varying degrees, which indicated that the failure of the coal samples induced the rebound deformation of the rock samples. With the increase in rock-coal height ratios, the rebound deformation amount of the rock samples decreased from 0.042 mm to 0.008 mm, and the rebound deformation rate decreased from 0.210 per cent to 0.010 per cent. Meanwhile, the rock samples’ rebound deformation releases part of the elastic energy to act on the coal sample, further contributing to the destruction of the coal samples. Compared with single composite coal samples, the coal samples of the composite samples have much more failures. In addition, with the increase in rock-coal height ratio, the input energy density, elastic energy density, post-peak release energy density, and residual elastic energy density of the composite samples increased, the dissipation energy density decreased, and the percentage of pre-peak elastic energy density increased from 98.56 per cent to 99.86 per cent. These results revealed the deformation failure characteristics of rock-coal composite with different height ratios and provided a theoretical reference for understanding the underground dynamic rock failures.

Nov 29, 2022

By André Vien, Robert Edwards, Rob Perry

A metallurgical control application can only succeed if the system's lowest common denominator, its instrumentation and regulatory control is implemented and maintained correctly. This paper describes the basics of regulatory control implementation including some practical guidelines for instrumentation installation, operator interface design, loop tuning, and continuous loop performance analysis. Tuning and analysis techniques are illustrated by step-by-step industrial examples. A small investment in basic control pays dividends in better overall plant performance and provides a solid foundation for advanced control efforts such as expert systems.

Jan 1, 2000

By Sylvain Duchesne, Claude Bazin, Robert Grant

Grinding simulators are now widely available to assist in the selection of circuit operating conditions or flowsheet designs that yield a given product size distribution. These simulators do not inform of the impact of the grinding product size distribution on subsequent flotation stages. This paper presents a method to predict the effect of fineness of grind on a flotation bank operation. Application of the method is illustrated with data from two Canadian concentrators.

Jan 1, 1995

By Corbett G, Iwai N

The Japanese gold mining industry has a long and productive history and is presently undergoing a period of revitalisation encouraged by the Hishikari discovery. Deposits exhibiting the characteristics of epithermal mineralisation are very widely distributed throughout the island chain and an encouraging number of these are large, seven containing gold in excess of one million ounces. All the important deposits are quartz vein type and contain extremely high grade, or "bonanza". Zones.

Jan 1, 1990

By Knut F. Garshol

Quality and durability of sprayed concrete depends on the concrete mix design, the type and use of accelerator and all the aspects of the placement onto the rock surface in the underground working. A large number of influence factors are involved and they must be managed for a successful and durable permanent sprayed concrete structure to be produced. The paper discusses some of the central issues, including how to view the long-term effects of chemical admixtures and accelerators in wetmix sprayed concrete. Permanent lining sprayed concrete for rock support is increasingly being used today and the durability can be equally achieved as for any other concrete.

May 1, 2003

By AIME

One of the operations of the J. L. Shiely Co. is quarrying in a hard granite gneiss with intrusions of gabbro or trap. During the winter of 1948-1949 the quarry ramp was lowered about 30 ft and during the 1949 season practically all drilling was done from the quarry floor, developing a face from 72 to 83 ft for the entire quarry area. The performance and cost table shows our record for 1948 and 1949.

Jan 1, 1950

By Frank C. Frischknecht

Most early development and application of electromagnetic prospecting methods took place in Scandinavia, where geological conditions favor their use. In other parts of the world these methods have aroused cycles of interest, but in Scandinavia they have been used continuously and successfully since the 1920's. Electromagnetic methods may be classified into two general groups. One group includes methods in which the source of the electromagnetic field remains stationary while the receivers are moved about to explore the area. The other includes procedures in which the energizing and receiving systems are moved together. Other classifications could be based on the size of the energizing source, the particular components of the electromagnetic field which are measured, or the mode of trans- porting the equipment. The difference between fixed-source and moving-source methods, however, is of such great fundamental importance that it will be emphasized in this discussion.

Jan 9, 1959

Design of cemented fill in mining is often carried out without any consideration of the structure of the fill. The composition of cemented fills varies in the stopes due to the placement method, and the strength of the fill in the laboratory depends on the density, orient- ation, moisture content and drainage conditions. Within each stope there are definite zones and the structure of both cemented rockfill and cemented hydraulic fill has to be defined for each zone and the field conditions simulated in the laboratory. Structure also affects fill permeability and compressibility. From a study of the cemented fill in place, the effect of changes in the placement methods can be seen and then controlled to improve fill performance and economy. These features of cemented hydraulic fill and cemented rockfill behaviour are discus- sed and illustrated through reference to field and laboratory work undertaken at Mount Isa.

Jan 1, 1973

By Yu-Jun Z

According to site measurement and labora- tory experiment, the authors suggest a new mathematical model of grouted rock bolts. The rock bolt is taken as an elastic bar, and the grout is substituted by a set of springs the rigidity of which is given as K. Based on certain assumptions, a simplified formula is deduced. When the category of rock, depth of tunnel, the spacing of rock bolts and the rigidity of springs K values are given, so that we can calculate the radius of plastic zone, and subsequently the convergence of rock at the tunnel inner surface u, and the resis- tance exerted by the rock bolt p. Finally, the length of rock bolt can be determined.

Jan 1, 1987

By Strathmore R. B. Cooke, Iwao Iwasaki, C. S. Chang

PYRRHOTITE has long been considered a gangue mineral to be eliminated as tailing in the treatment of various sulphide ores. However, in recent years the world-wide lack of sulphur resources has called attention to this mineral as a potential source of both sulphur and iron. Its importance as an economic mineral, however, has not been particularly emphasized. For this reason very little is known about its response to flotation, except that it can be depressed easily in alkaline circuit, by long aeration,1,2 addition of oxidizing agents3 or by starch.4 The object of this work was to study the floatability of pyrrhotite. This includes the effect of oxidation by aeration, of copper activation, and of change in pH.

Jan 2, 1954

By T. H. Dubaniewicz, J. E. Chilton

Fiber-optic technology is progressing rapidly, including the development of fiber-optic sensors for many applications. These sensors have the advantages of high sensitivity, light weight, small size, high bandwidth, and freedom from electromagnetic influences. The U.S. Bureau of Mines is investigating the use of fiber-optic technology to monitor mine atmospheres. This report describes a methane monitor based on differential absorption of infrared light. The monitor can detect methane concentrations as low as 0.2 vol pct as far away as 2 km via fiber-optic cable. The upper range is 100 vol pct methane. Since the system requires no electrical power within the mine, it is intrinsically safe.

Jan 1, 1992

By Xia Guangxiang, R. Y. Wan, Yang Hanlin, M. C. Fuerstenau

The mechanism and kinetics of pretreatment on pyritic gold concentrate with the catalytic oxidation acid leach (COAL) process were studied in the temperature range of 80-100°C and oxygen pressure range of 230-1013 kPa, with sodium lignosulfonate (SL) and mixed medium of sulfuric acid (11 g/[ ]) and nitric acid (5.5 g/ [ ]). The results show that nitric acid acts as a catalyst, the surfactant changes the hydro-phobicity of resulting elemental sulfur to favor the oxidation of pyrite, and the oxidation-determining step would be the chemical reaction between nitric acid and pyrite. When about 80% of pyrite contained in the concentrate is oxidized, the gold cyanidation extraction exceeds 95 % . The nitric acid in solution can be recycled and used again.

Jan 1, 1993