Search Documents

By D. L. Ward

This paper is the result of a study, in 1919, to determine how much surplus power could be produced through the proper utilization of the entire gas flow from the two furnace stacks at the Federal Furnace Plant, South Chicago, Ill. Obviously, the problem was to measure the flow of gas through the main beyond the point where the amount necessary for stove operation was removed. In all probability, blast-furnace gas is the most difficult gas to measure, because of the high moisture and dust content, and the widely fluctuating flow from the furnaces. This wide fluctuation of flow forbids the acceptance of any one group of flow readings as indicative of normal operating conditions. A study of the conditions showed that a recording device on gas flow was necessary. As the gas at the point of measurement had passed through wet washers, and accordingly was saturated with water and contained considerable dust carried past the scrubbers in the form of sludge, no form of Pitot tube could be used, for this sludge would quickly plug the dynamic and static holes, spoiling the gage readings. An even more serious objection to the use of Pitot tubes was the impossibility of accurately measuring the cross-sectional area of the gas main on the plane of Pitot-tube installation. Given an absolutely clean gas and a perfectly circular pipe, it would be safe to assume, through measurements of the pipe diameter, that the gas main was of a certain cross-sectional area. But the continual depositing of sludge and the fact that the main was fabricated from riveted sheets led us to discard the idea of using Pitot tubes for this service. The Venturi tube was then considered, and had there been a sufficiently long straight run of gas main to accommodate a tube of the required size (72 by 28 in.) such an installation would very likely have been made.

Jan 2, 1921

By Dana Reinke, Launa Mallett, Michael J. Brnich

Some segments of the mining industry, especially underground coal, have seen a large influx of inexperienced miners in recent years. It is anticipated that this trend will reach other mining segments over the next 10 years. This paper discusses the training needs of the younger generation of inexperienced workers who have just entered or are soon to enter the mines. Currently, many trainers are of the so-called Baby Boom generation. Can these different age groups learn to communicate across the generation gap? Even trainers who have been highly effective in the past should reassess their training styles and their classroom materials to determine if they are prepared to meet the needs of these new trainees.

Jan 1, 2002

By Levent Ozdemir, Robert J. Evans

An ongoing research program at the Colorado School of Mines is investigating the application of low to moderate pressure water jets to assist the cutting performance of drag type cutter bits commonly used on coal mine cutting machinery. The results to date indicate that a water jet directed to impinge the rock in the immediate vicinity of cutter tip can provide significant benefits in terms of reduced cutting forces, prolonged bit life and less airborne dust, as well as reduced tendency of sparking during cutting. This paper describes the findings of this research effort designed to fully evaluate and optimize the parameters affecting the performance of a combined water jet assisted drag bit cutting system for coal mine applications.

Jan 1, 1983

By Massy-Greene RB

Limited recourse financing techniques reduce the financial exposure of equity holders to major mining projects by transfering some of the risks to the banks which provide loan funds for project development. This can only be achieved by a clear understanding of the principles involved. Engineering and management decisions on how the resource is to be developed and extracted must be made in the light of lender's requirements. The structure of sales contracts, joint venture agreements and many other documents can be important in limited recourse financing. If projections show that the debt can be repaid from project cash flow, loan agreements and other arrangements can restrict lenders ability to look to the equity holders for repayment of project loans.

Jan 1, 1981

Load transfer capacity and failure mechanism of a fully grouted bolt installed across joints in shear is evaluated both experimentally and numerically in five types of bolts (low strength steel, rebar bolt and high strength steel). The strength of the concrete, bolt profile configuration, bolt mechanical properties and bolt pretension load play significant influence on the shear resistance, shear displacement and failure mechanism of the reinforced medium. Failure location moves towards the bolt joint intersection due to the increasing shear load, shear displacement and axial load developed along the bolt. Finally bolt failure occurs as a result of the induced axial and shear stresses acting between hinge points on either sides of the shear joint plane.

Jan 1, 2006

By L. S. McNickle

[Commonly accepted maintenance methods are being outdated by the rapid acceptance and use of more complicated hydraulic circuitry on modern mining equipment. It is no longer adequate to use the maintenance program to merely repair or sustain equipment operation. Ever increasing operating costs place a huge premium on lost production time. It has, therefore, placed the maintenance programs in the position of being required to alleviate equipment malfunctions on production shifts and still attain the maximum unit life from each component part.]

Jan 1, 1961

By I. Mikov

Established in the 60-ies, the Zlatna Panega quarry is a cement raw materials quarry supplying 95% of the needs of the Zlatna Panega Cement Plant with limestone, marl and other silica-aluminates. The two major types of raw materials are formed by accordingly dipping strata of Upper Jurassic limestones and lower Cretaceous marls. Between them there is a ?transition-zone? or ?contact-zone? of a high-silica content layer, about 5-m thick, defined as ?flint? by investigations including spot sampling throughout the quarry. For many years this ?contact-zone? layer was neglected due its negligible thickness. Further, with the increasing demand on the quality of the raw materials feed to the Plant and the focus on variability of the chemical and mineralogical components, it was decided not to mine any of the parts of the quarry contaminated by this material, for about three years. The latter had an impact on the availability of operating benches that could result in a substantial decrease in the total recoverable re-serves of Zlatna Panega, particularly with respect to marls. There were considerations for resorting to a partial, selective excavation of the quarry pit with a reduced lifetime for the lime-stones and re-opening of an other (currently in-active) marl quarry at a distance of 6 Km from the Plant. The Quarry Team of the Zlatna Panega quarry was assigned to study the problem. The ?contact? layer was duly confirmed with systematic geological (including mineralogy) studies, statistical analysis of available data, surface sampling and shallow exploration drills, resulted into distinguishing a third type of reserves and their credible subsurface delineation by means of geological 3-D modeling and quarry design. A new quarry design was finally elaborated with a view of providing flexibility in mining, utilization of the total volume of all available reserves and maximizing the mine life of Zlatna Panega quarry. An industrial test took place in December 2005, by using the contaminated parts of the quarry (co-mining of the ?contact-zone? materials) at a contribution of 15-20% in the raw materials mix, as dictated by their contribution in the total recoverable resources of the quarry. The purpose was to investigate the viability of this solution ? in line with improved quarry planning ? without compromising the quality of cement production and the efficiency of Plant Operations. Results were overall successful.

Jan 1, 2006

By F. M. Perkins, R. H. Jamison

Publications concerning scaling laws for laboratory flow models of oil reservoirs indicate that the relative permeability and capillary pressure relations must be the same functions of saturation in the model and its prototype. In this paper, the relative permeabilities and saturations are redefined in a way which permits one to have diflerent relative permeability and capillary pressure relations in the model and prototype. The development of the new scaling criteria is demonstrated by deriving scaling laws for one simple flow problem. INTRODUCTION The successful application of information gathered through bench-scale model studies to the prediction of multi-phase fluid flow behavior in petroleum reservoirs requires careful consideration of the scaling criteria. The requirements which must be met for a small-scale model to duplicate the behavior of a much larger reservoir prototype have been discussed by Leverett, et al,' Rapoport,2 and Geertsma, et al.3 According to these authors, the relative permeabilities to water, oil and gas and the dimensionless capillary pressures must be the must have the same values in the model and prototype. Furthermore, they point out that the viscosity ratios must have the same values in the model and prototype. In addition to these requirements, other scaling criteria are given which, when considered, usually dictate a much higher permeability in the model than exists in the reservoir. Since the more permeable model sands may have connate-water and residual oil saturations quite different from those in the prototype, the scaling requirements pertaining to the dependence of relative permeabilities and dimension l ess capillary pressures on saturation usually are not met. Also, if the model fluids are selected to give equal viscosity ratios in the model and prototype, one may find greatly different mobility ratios* in the two cases and, therefore, may expect grossly different flow patterns. For this reason, Craig, et al,' correlated the results of their model studies with mo- bility ratio rather than with viscosity ratio. As yet, however, no satisfactory method has been advanced which permits use of anything other than the scaling requirements outlined in the previously mentioned papers. The purpose of this paper is to present a method of developing a set of scaling criteria which permits different relationships between saturation and relative permeability or capillary pressure in the model and prototype. Rather than attempt to report scaling criteria for a variety of practical situations, this paper demonstrates by use of one simple example how the modified scaling criteria are derived.

By Allan T. Fisk, Carl R. Peterson, Robert G. Lundquist

A long recognized goal in high speed tunneling and mining has been the development of a continuous drill and blast excavation capability. Both the advance rate and the economy of drill and blast tunneling can be significantly improved if the conventional cyclic process can be carried out continuously. Obviously, any continuous drill and blast tunneling machine must be an "all function" device, performing drilling, explosive loading, initiation, mucking, ventilation, roof support (if necessary), and perhaps other functions, essentially simultaneously, while remaining at the face throughout. Furthermore, such a machine must do all these things under remote control. THE SPIRAL BLAST PATTERN Several continuous drill and blast tunneling concepts have been proposed. Of these the Rapidex spiral blast pattern, taking advantage of a partially self-shielding geometry, seems to require the least shielding and hence offers the maximum access for mucking, although from the outset it was clear that remote mucking would present a major design challenge. The Rapidex continuous spiral blast concept uses an unusual blasting pattern that, under the geological conditions tested, has proven to be an effective and efficient means of fragmentation. The concept has a self-shielding characteristic which permits a lightly shielded machine to remain at the face during blasting. The pattern produces a spirally proceeding tunnel face, much like one turn of an auger. The leading portion of the spiral surface is connected to the trailing portion by an axially extending plane surface or bench. The ideal geometry is illustrated in Figure 1 for a horseshoe tunnel section.

Jan 1, 1979

By N. A. Ziegler

A certain amount of interest has been indicated recently in the resistance to oxidation at high temperatures of iron-aluminum alloys (rich in iron). Hautmanl published a paper in which some interesting results are given. According to his paper, only alloys containing at least 8 per cent aluminum indicate a marked improvement in their resistance to oxidation. At about this aluminum content, however, alloys become brittle, which considerably reduces their commercial value. About two years ago the author performed a series of experiments, the results of which are presented here. A series of iron-aluminum-carbon alloys was prepared by melting electrolytic iron, aluminum and high-carbon iron alloy in an induction vacuum furnace.2 The list of these alloys is given in Table I. Each alloy was forged in the ordinary way to All carbon determinations were performed by " Yensen " method. [N. A. Ziegler: Recent Developments in Analysis of Carbon in Iron and Iron Alloys. Trans. Amer. Electrochem. Soc. (1929) 56, 231.1

Jan 1, 1932

State Mine Experiment Station, College of Engineering, University of Alabama, University, Ala Copies of two bulletins issued by the Mine Experiment Station may be had by writing to the Director of the School of Mmes at the above address: Bulletin 1, Coal losses in Alabama, 2, A specific gravity study of Alabama coals The Cooperative work of the Mine Experiment Station with the Southern Experiment Station of the U S Bureau of Mmes is covered by Bulletins of the U S Bureau of Mines

Jan 1, 1933

The alkaline ethylenediamine tetra-acetic acid (EDTA) leach process for extracting tungsten from scheelite (CaW04) ores has been examined for the treatment of low grade (<0.5 per cent WO,) residue dumps. The process has been considerably simplified by applying solvent extraction directly to the leach liquor.Ammonium paratungstate is thereby produced in a one step process and this obviates the need to physically recover EDTA prior to recycling. This modified process should be an economical method of tungsten extraction.

Jan 1, 1983

By H. W. J. P. Neomagus, J. R. Bunt, T. S. Mthombo, C. A. Strydom

"Low-cost calcium lignosulphonate (CL), which is a byproduct of the wood pulping industry, was investigated as a potential binder during laboratoryscale pelletization of inertinite-rich high-ash coal fines from the Highveld Coalfield of South Africa. Coal-binder mixtures containing between 1 and 15% calcium lignosulphonate were prepared, pressed, and ultimate, proximate, porosity, XRD, and XRF analyses obtained. It was found that increased pressure during pelletization results in increased attractive forces, due to increased interparticle contact areas. FTIR analysis showed that chemical interactions occur between coal fines and the binder, as evidenced by the formation of new C-O ether-type bonds. The presence of moisture during pelletization enhanced surfactant activity of the binder. Chemical interactions between the coal and the binder seem to be mainly electrostatic, driven by Ca2+ from the calcium lignosulphonate, which may act as a bridge between the anionic parts of the binder and the surface of the coal. IntroductionCoal has over the years remained South Africa’s major energy source, with over 90% of the country’s electricity being produced via coal-fired processes (Arndt et al., 2016). Sasol’s coal conversion technology alone provides more than 40% of South Africa’s liquid fuel requirements (van Dyk, Keyser, and Coertzen, 2006). The production of high-grade coal requires the processing of run-of-mine (ROM) resources by a combination of processes which include crushing, screening, and washing (Radloff, Kirsten, and Anderson, 2003). These processes result in the generation of coal fines (< 0.5 mm) which, until recently, have been discarded into slimes dams (le Roux, Campbell, and Smit, 2012). Several issues are associated with slimes dams, among which are the costs of transportation of these fines from the place of origin to the discard point (often a considerable distance), and the potential environmental effects due to seepage of toxic materials into surrounding ecosystems (Clausen, 1973).Consequently, utilization of these coal fines is an area of great interest. Mechanical densification of fine coal by means of pelletization and/or briquetting to larger sizes for use in technologies that require lump coal, such as chain-grate stokers and fixed-bed gasifiers, has been shown not only to reduce environmental risks (Mangena et al., 2004), but also to significantly reduce storage and transportation costs (Mani et al., 2001). Pelletization is the process by which solid particles are consolidated into uniform, usually hard, impact-resistant agglomerates, rendering them useful as a fuel with sufficient calorific value for domestic and industrial utilization (Finney, Sharifi, and Swithenbank, 2009)."

Dec 1, 2018

By S. N. Groudev

Intensive uranium mining activities at the Curilo deposit in Bulgaria has caused widespread contamination over a wide area. A number of receptors including soils and watercourses as well as the ecosystems in the area have been severely affected. Even today, 10 years after the cease of activities, acidic waters generated from the abandoned mining works, the low-grade ore and waste dumps contaminate soil, surface- and groundwater. The present paper describes in general the environmental status of the wider Curilo area and examines the potential of preventive and remedial measures that can be applied in situ to rehabilitate the site and restore the ecosystem. The main rehabilitation technologies examined include modification of the acid generation potential of the pollution sources, treatment of the acidic drainage by means of a natural wetland and in situ bioremediation the of contaminated soils. Finally, a number of efficient indicators are proposed so that the rehabilitation potential at Curilo and similar heavily contaminated sites is assessed.

Jan 1, 2003

By D. J. Hutchinson, S. Nickson

Cable bolts are used as a means of rock support around underground excavations in many mines across Canada and around the world. A substantial body of research on cable bolting was conducted at a number of Canadian universities and mines from the mid-1980s through the 1990s. Since then, research into selected areas of cable bolting practice has continued in Canada. The research has focussed on cable bolt instrumentation and on the inclusion of cable bolts in empirical stope design techniques. A review of cable bolting practice is now warranted at many mines. It has been five years since the completion of the previous substantial body of Canadian academic research and the associated advancement in understanding of cable bolt design, implementation and verification practice. Attempts were made at that time to transfer the new design procedures and performance assessment technologies to mine-site personnel. In some cases, this was effective, and ground control personnel continue to improve on their cable bolting practice at each specific mine site. However, at other sites, experienced people have moved on, and the new, less experienced personnel do not have access to the training or technical resources required to improve their understanding of the subject. In other cases, the technology was not transferred effectively to practitioners, with the result that substantial improvements can be made to the cable bolting practice at those mines. Guidelines for auditing cable bolting practice are provided in this paper. The guidelines include a discussion of the objectives of the audit, suggestions for audit procedure and a summary of the possible outcomes of a cable bolt audit. The objectives of an audit might include assessing the reasons for unexpected cable bolt failures, evaluating the quality of the installation procedures, quantifying the efficiency of the cable bolt system and assessing training requirements and procedures. A cable bolt audit should include consideration of all aspects of the cable bolting cycle, including the design, implementation and verification phases of the operation. At the end of the audit, a ranking should be assigned to the components of the cycle. The ranking system can then be used to identify items that require immediate attention, others that could be improved and others that are adequate. Following completion of a cable bolt audit, increased confidence in the support system and its application is generally, found, along with the potential for cost savings in many cases.

Jan 1, 2002

By Frank J.

The increased demand for aluminum for military purposes during World War II necessitated the development of domestic deposits of alumina-bearing ores. Kaolin, siliceous bauxites, anorthosite, and diaspore-containing clays have been investigated and studied in the laboratory and pilot plant. The Bureau of Mines is preparing a series of reports covering investigations of these ores. The tests contained in this report are restricted to sintering and leaching tests on kaolin from South Carolina, where extensive deposits were proved to exist. The leach liquors were found to have substantially the same composition as those produced from the diaspore-containing clays, and therefore it would be expected that no difficulty would be experienced in producing calcined alumina of relatively coarse particle size and with other properties conforming to the specifications for metallurgical-grade alumina.

May 1, 1947

By Kuda R. Mutama, Allen E. Hall

A wind tunnel investigation into the fundamental characteristics of jet fan performance is described. The effects of varying fan positioning in a square tunnel cross section are reported for two fan outlet diameters and velocities. Tests were conducted, also for a jet fan placed in a flow developed by an external fan operating in the same direction as the jet fan. The position of the jet fan relative to the tunnel walls was found to affect its performance. Performance parameters were determined and used to formulate theoretical equations based on momentum and energy considerations. The results identified a range of flow ratios which can be used to design an effective jet fan ventilation system and provide a basis for the selection of jet fans for practical mining applications

Jan 1, 1997

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, BRADLEY BENNETT, Patrick Zhang

The purpose of this work is to develop a conceptual recovery process for thorium dioxide (ThO2) from its primary source, monazite. The study-level design presented in this paper represents an economically viable method for conducting ThO2 extraction from monazite ore while also recovering byproducts that include P2O5 and other rare earth element oxides rather than producing unnecessary waste streams. Three key points to note in the development of this process design are: (1) the process economics relied heavily on recovery of rare earth byproducts, (2) the thorium handling portions of the process could effectively be segregated from the rare earth and phosphate handling portions of the process, and (3) the thorium and uranium content in waste streams should be carefully managed and eliminated where possible.

By R. Y. Wan, J. D. Miller

Thiohydrometallurgical systems including thiosulfate, thiocyanate and thiourea have been stud- ied as alternative liriviants for the leaching of gold. Research and development of thiohydrometallurgical technology has been prompted by environmental concerns with the use of cyanide and problems associated with the processing of difficult-to-treat ores. These thiosystems have some chemical similarities, enabling gold to be leached in a practical oxidizing environment. However, the solution chemistry of the thiosystems is complicated due to instability of the thioreagents and many other reactions which occur during the gold leaching reaction. In this paper, interference reactions of selected metal ions and sulfide minerals are examined in order to understand important aspects of solution chemistry which control the stability of the thioleaching reactions. Applications using thioreagents as lixiviants for oxide and refractory gold ores are presented.

Jan 1, 2005

During the past five years there has been a transformation in the operating costs which apply to narrow vein mining. Mechanised methods including sublevel uphole retreat and narrow vein cut and fill are now proven. Other methods, such as vein mining by horizontal drilling from a raise platform are currently being tried in Australia.The important factors which affect the cost and appropriateness of each method include: ore continuity, the planarity of the wall contacts, relative hardness of ore and wall rocks and the dip bf the deposit.Drawing on current operating costs from a number of mines and on recent feasibility studies, a methodology for estimating the costs of narrow vein mining is presented. These costs are then placed in their economic context with regard to ore grade and mining rate.

Jan 1, 1993