Search Documents

By Newman H. A

Goldsworthy Mining Limited is currently mining iron ore at an annual rate of 7 million tons from several small orebodies, each of which exhibit wide variations in iron, phosphorus, silica and alumina contents. Each orebody is mined at its average ore reserve grade and therefore mine planning and grade control techniques have had to be tailored to achieve a constant production blend.

Jan 1, 1973

By J. P. Savely, D. E. Nicholas, R. D. Call

Slope stability is a probabilistic phenomenon and as such should be analyzed with probabilistic methods. Fracture orientations alone, insufficiently model the rock mass. Other parameters describing the fracture set characteristics are required with distributions that can be sampled to fit mathematical stability models. Important considerations are length, spacing, dip, waviness angle, and overlap. These parameters are of major concern in design and are difficult to measure. Reasonable estimates of the characteristics can be used to provide distributions.

Jan 1, 1977

By Rankin W. J

Increasing concern with the emission of sulphur dioxide from smelters and roasters has caused renewed interest in processes which can use waste sulphur dioxide, such as the sulphation of nickel laterite ores. The process described here proposes to by-pass the production of sulphuric acid and react laterite directly with a sulphur dioxide containing atmosphere. A thermodynamic analysis identified operating windows in which nickel sulphate forms while iron oxide (the major impurity in most laterite ores) remains stable. The initial assumptions included unit activity of all species except nickel oxide. The lowest possible nickel oxide activity (while maintaining selectivity) increased with increasing temperature, indicating that selective sulphation is favoured by low temperatures. The temperature of interest was found to be between 500 and 800¦C. Calculations show that a feed gas containing ten per cent SO2, five per cent 02, balance N2 requires a temperature greater than 650¦C for selective sulphation of nickel. Laboratory experiments showed that the assumption of unit activity of ferric sulphate was unrealistic above about 680¦C due most likely to the formation of solid solutions which decreased the ferric sulphate activity. Results are presented which illustrate the limiting equilibrium sulphur trioxide partial pressures at 700 and 730¦C below which selective sulphation occurs. Cobalt extraction was usually between 80 and 95 per cent under conditions yielding selective sulphation, whilst nickel extraction was about 50 to 75 per cent depending on temperature and choice of upper limit of iron extraction. An operating diagram is presented for a limonite ore and shows that the optimum reaction conditions are 680¦C and an input gas containing 20 per cent SO2. Under these conditions nickel, cobalt and iron extractions are 73, 95 and two per cent respectively.

Jan 1, 1996

US 4,194,729 - Sintering of iron oxide ore on a straight sinter belt. The upper strand of the belt is divided into sintering and cooling sections with windboxes for removing their respective gases. The main for collecting cooling gas is located beneath the lower strand and is connected to opposite sides of the windboxes, while the main for collecting sinter exhaust gas is located beneath the lower strand and connected to sinter section windboxes. Both mains are exhausted via gas-evacuating fans and pipes to a flue. Space requirements are lessened and plant accessibility can be maintained at optimum conditions. K. Wacker and F. Feigk, assigned to Dravo Corp. Mar. 25, 1980. 8 pp. (266-144). Filed: 10-30-78 (956,058). Priority: West Germany, 12-16-77 (2,756,082).

Jan 1, 1982

SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York; its corporate name is American Institute of Mining and Metallurgical Engineers, Inc.; and its abbreviated title A. I. M. E. SEC. 2. The objects of this Institute, as set forth in its certificate of incorporation, are: "To promote the arts and sciences connected with the economic production of the useful minerals and metals, and the welfare of those employed in these industries by all lawful means; to hold meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members the information thus obtained, and to establish and maintain a place for meeting of its members, and a hall for the reading of papers and delivery of addresses, and a library of books relating to subjects cognate to the sciences and arts of mining and metallurgy." ARTICLE II MEMBERSHIP SEC. 1. The membership of this Corporation shall include all those who on the third Monday in February, 1928, were members and all others subsequently elected and qualified in accord with the By-laws of the Institute at the time of such election. SEC. 2. The membership shall be divided into such classes as may be from time to time fixed by the By-laws. ARTICLE III DIRECTORS SEC. 1. The business, financial, professional, technical, scientific and social interests of the Institute shall be managed by a Board of Directors, elected annually by letter ballot in the manner specified in the By-laws, to serve for the terms as set forth in the Certificate of Incorporation. ARTICLE IV AMENDMENTS SEC. 1. Proposals to amend this Constitution may be made by resolution of the Directors or by written petition signed by at least ten members. Such proposals must reach the Secretary not later than October fifteenth. The Board of Directors shall consider them and, in case of petitions, the proposers shall be notified of the opinion of the Board in regard to them, when they may cither withdraw their proposals, or accept any changes suggested, or insist on the original form. All proposals when in final form shall be mailed to all members on or before January first, with the election ballots, and with a ballot in proper form for voting on the amendment in its original or amended form. Ballots shall be received by the Secretary until the second Tuesday in February. The Tellers of the election shall count these ballots,

Jan 1, 1929

One of the responsibilities of the Melbourne and Metropolitan Board of Works is to provide a sewerage system for the metropolis of Melbourne which now contains over 2.5 million people. In providing this sewerage system it was necessary for the Board to embark on a large tunnelling programme some 20 years ago. As a result of this extensive tunnel construction programme, tunnel boring machines and shaft sinking methods have been developed to cope with the soft ground and soft to medium rock found in the southern and eastern areas of Melbourne where the majority of the recent tunnelling has been carried out. While in the last few years radical changes in construction methods have not been made, development has continued and improvements have been made, which have enabled the Board to extend the limits of the ground conditions in which it can efficiently construct shafts and also tunnels with boring Machines.

Jan 1, 1976

By D. S. Conochie

The world is poised for rapid growth in consumption as large, less developed economies acquire greater wealth. It might be expected that there would be a corresponding growth in waste generation, but this might not necessarily be the case. The metallurgical industry has an excellent record of process development which has allowed it to provide a high tonnage supply of low cost, high quality metals. Environmental challenges have been faced and indeed the recycling of scrap iron through the electric arc furnace has made a massive contribution to cleaning up obsolete structures and equipment of past generations. Issues in waste generation and processing still remain, and the expectation for cleaner processing and environmental performance continues to rise. The waste impact of key process developments of the last century and the recent developments in metallurgical waste processing in Canada will be outlined. The potential to use state of the art design tools to produce the next generation of zero waste processes will then be explored.

Jan 1, 2004

By John S. Stevenson

The Twin ''J' mine is on mount Sicker; 8 miles by road northwest from Duncan; on Vancouver island. It includes the old Lenora; Tyee; and Richard III mines; formerly under separate ownership but now under the single ownership of Twin "J' Mines; Limited.

Jan 1, 1954

By M. C. Baumann

The Getchell Mine is located in Humboldt County, Nevada, approximately 70 km northeast of Winnemucca. Slope management has been a critical factor in the feasibility of mining operations since they began in the early 1930's. Although underground entries began in 1937, underground production was limited because hanging walls consisting of clay gouge and crushed rock tended to collapse into the workings. Controlling these collapses required extensive timbering. Due to these poor ground conditions, surface open-pit mining was the primary mode of production from 1938 to 1967 with only minor contributions from underground operations. Mining was suspended in 1967 due to economic pressures. From 1960 to 1967, the previous operator mined the property in three open pits. Initially, these pits were constructed with footwall benches, but these failed. These failures were aggravated by construction of 60° slopes in footwalls with shale partings dipping into the pit at 43° to 60°, resulting in large planar failures and wedge failures. In response, the previous operator adopted a slope parallel to the bedding planes.

Jan 1, 1993

By J. Vilcáez

The copper extraction yield from thermophilic bioleaching of chalcopyrite depends on temperature, pH, and the oxidation-reduction potential (ORP), as well as the activity of the microbe used. We studied copper extraction yields obtained from chalcopyrite with three thermophiles, Acidianus brierleyi, Sulfolobus metallicus, and Metallosphaera sedula, under various pH and temperature conditions and with different initial amounts of ferric iron. The results indicated that the capacity of each thermophile strain to leach iron as Fe3+ differed, which affected the influence of pH, temperature, ORP, and microbial activity level on the yield of copper. Microbial activity can cause ORP to be close to the critical value (450 mV) at which copper extraction at 65 °C can be higher than that at 80°C. An initial pH of 1.5 retards the precipitation of jarosite, allowing temperatures as high as 80°C to result in copper extraction yields close to 100%. However, if a thermophile with a poor capacity to form Fe3+ is employed, 100% copper extractions can also be obtained at pH 2.5, because ORP is low as result of low amounts of Fe3+ in solution. Optimum temperatures for the growth of thermophiles did not always mean high copper extraction yields. Conversely, high biomass concentrations depending on the capacity of the thermophile strain to leach iron as Fe3+, can result in excess Fe3+ in solution, leading to the precipitation of large amounts of Fe3+ as jarosite. The bioleaching capacity of A. brierleyi was reduced or suppressed when insufficient initial Fe3+ was pro-vided to trigger the leaching reaction, whereas S. metallicus and M. sedula were less sensitive to the initial availability of Fe3+. This result confirmed that a direct enzymatic attack on the mineral surface could initiate the leaching reaction, but later ORP governed the leaching rate of chalcopyrite.

Jan 1, 2014

By Bruce D. Sartwell

A program was written which utilizes a remote teletype input to a time- sharing computer to plot charged particle or X-ray energy spectra which are stored in the memory of multichannel analyzers. The program, written in FORTRAN V, accepts the data printed out by the pulse height analyzer on paper tape and then, after reading these data tapes into the computer, plots on the teletype the desired energy spectra on a scale automatically adjusted for the maximum number occurring in the data. The program is flexible enough so that the researcher can subsequently expand or contract the vertical (intensity) or horizontal (energy) scales. With a slight modification, the program will accept data printouts from scalers or analog to digital converters. The program also includes a feature for integrating the energy peaks obtained by pulse height analysis.

Jan 1, 1970

By Thomas G. Hayes

Track-type tractors remain one of the most cost-efficient stripping tools available to coal miners. Whether they are "sweetening up" a dragline operation with prebenching or serving as the primary tool, dozers are important in driving down mining costs. This article reviews the application zone of track-type dozers. It also provides suggestions for site setup, equipping tractors and machine operation. In recent years, the track-type tractor has become more of a production tool in mining. With the advent of bigger machines, bulldozers have become a typical component in mining operations, removing overburden down to the top seam of coal. Large tractors can also be teamed up with draglines and other systems to maximize the effectiveness of the mining system. Bulldozers remain the tool of choice for topsoil removal, spoil reclamation or any application that demands low ground pressure, or short distance. The introduction of the 523-kW (700-hp) track-type tractor to the mining industry has made the bulldozer a low-cost-per-ton means of removing overburden. The large tractors offer enough productive capability to be considered prime stripping tools. And they can lower mining costs by complementing other mining systems (dragline, cast blasting and loader/truck). Four criteria determine whether a track-type tractor is the right machine for a particular application: ? Production requirements - dozer may fit job requirements better than a second dragline. [ ] ? Product support - availability of parts, service and technical expertise. ? Labor situation - how much of the cost per ton goes to the operator. ? Resale opportunity - recover a percentage of capital cost. Mining efficiency is economically controlling the cost of any system. Most operations rate the most economical means of moving material as cast blasting, dragline and the track-type tractor. All three of these systems share one common value: They are all sensitive to distance. Regardless of the application, all mining systems have an economic range. Exceeding this distance will affect cost and productivity.

Jan 1, 1997

By D. R. Miller

Internal friction and elastic modulus variations in electrorefined titanium, iodide refined titanium, and alloys of the latter material with oxygen, nitrogen, aluminum, and zirconium were investigated. No oxygen peak was detected with electrorefined titanium but, provided precautions were taken to prevent increases in background damping, an oxygen peak at about 410°C could be resolved with each of the other materials. An additional partially resolved peak was observed at 500°C in a Ti-N alloy. An anomaly in the variation of rigidity modulus with temperature was observed. Possible mechanisms for the formation of any oxygen peak have been discussed. PRATT, Bratina, and Chalmersl investigated the internal friction of commercial purity titanium and alloys of this material containing 1.5, 3.5, and 4.5 at. pct O. With commercial titanium the internal friction curve consisted of two components, a background which increased steadily with temperature and a peak at about 600" C which was due to grain boundary relaxation. In the Ti-O alloys, however, an additional internal friction peak was observed at 430" to 450°C and, since this peak increased in height as the oxygen content was increased, it was thought to be associated with the presence of oxygen. The diffusion of oxygen in titanium at temperatures between 300" and 500° C is believed to have marked effects in its tensile properties2'3 and the present internal friction measurements were undertaken to obtain further information on this diffusion, using material of higher purity than that of Pratt et d. and an apparatus of very much greater sensitivity. In the course of the investigation a number of important limitations on the work of Pratt et al. were revealed and results have been obtained which emphasize the need for ensuring that in this type of experiment, internal friction is independent of strain amplitude and that the values obtained are reproducible. 1) MATERIALS AND APPARATUS The basis material from which the majority of the specimens was prepared was iodide-refined titanium, the major impurities in which were oxygen and nitrogen—the metallic impurities being present at concentrations less than 0.001 at. pct. The hardness of this material after arc melting, forging, and swaging to rods 1/4 in. diameter was Dph = 110. Specimens 10 in. long and 0.020 in. (0.51 mm) diameter were prepared from these rods by further swaging and wire drawing and were finally annealed in vacuo (5 x 10-6 mmHg) for 24 hr at 800°C. The oxygen alloys were prepared from iodide-

Jan 1, 1962

By Sherwin F. Kelly

One of the most succinct and illuminating perspectives of the field of geophysical exploration to appear in recent years is an article by E. A. Eckhardt, in the magazine Geophysics for October 1949. Although his review covers the year 1948, many of the data presented are apropos to a review of 1949, and form a pertinent background for a consideration of current progress. He presents charts of the world-wide distribution of gravimeter and seismograph activity in oil exploration, which show that surveys in the United States accounted for practically 68%; of all gravity work and 80%; of all seismic activity. Canada ranked second, with a proportion of roughly 6%, in each case; South America accounted for about the same percentage of seismic work, and double that amount for gravity surveys. Within the United States, Texas and Louisiana were the scenes of the greatest activity, both claiming about 60% of all surveys by each method.

Jan 1, 1950

By M. Hakala, P. Tolppanen

A method to predict stress-induced failures around excavations based on the mapped geological and rock mechanical information is studied. Totally of 7 km of newly excavated tunnels are mapped in the Inmet’s Pyhäsalmi mine in Finland at depth between 1000 - 1440 m from which the results and conclusions from the firstly mapped 1.7 km of tunnels are reported. The main rock type at the site is very hard volcanite having uniaxial compressive strength of 230 MPa in median and GSI-value 72 - 80. The maximum in situ stress around the tunnels is 65 - 85 MPa. The prediction of observed stress failures was preceded by comparing elastic 3-D simulation results of tunnels with three statistical yield criteria. Read’s or Hoek & Brown’s yielding criteria are found the most relevant, though, the effect of anisotropy was found to be significant. The most important parameters having a correlation with stress failures are the tunnel orientation and the foliation of rock. Also, the rock type and its strength, tunnel shape and the geological anomalies have their effects. Further, a delay time on mapping was found to clearly diminishing of the most violent failures. Une méthode de prédiction des contraintes à la rupture autour d'excavation, établie sur la base de cartographie géologique et d'information sur la mécanique des roches, à été étudiée. Au total, 7 km d'un tunnel nouvellement percé à une profondeur de 1000 à 1400 m ont été cartographiés dans la mine de Inmet’s Pyhäsalmi en Finlande. La roche principale du site est une vulcanite dur ayant une résistance à la compression uniaxiale de 230 MPa (valeur moyenne) et une valeur GSI de 72 - 80. La contrainte in situ maximale autour du tunnel se situe entre 65 et 85 MPa. La prédiction des contraintes à la rupture observées a été évaluée en comparant les résultats d'une simulation 3D d'un tunnel avec trois critères de limite d'élasticité statistiques. Le critère de limite d'élasticité de Read ou de Hoek & Brown’s se trouvent être les plus important, même si les effets de l'anisotropie sont significatifs. Les paramètres les plus importants ayant une corrélation avec la rupture sont l'orientation du tunnel et la foliation de la roche. De plus, le type de roche et sa résistance à la compression, la forme du tunnel et les anomalies géologiques ont aussi leur importance. Finalement, un délai dans la cartographie résulte en une diminution nette des ruptures violentes. Basierend auf kartierten geologischen und felsmechanischen Informationen, wird eine Methode untersucht, um spannngsbedingtes Versagen um Ausbrüche herum vorherzusagen. Insgesamt werden 7 km neu ausgebrochenen Tunnels in einer Tiefe zwischen 1000 und 1400 m in der Inmet Pyhäsalmin Mine in Finnland kartiert. Das hauptsächlich vorkommende Gestein ist sehr hart und vulkanischen Ursprungs mit einer mittleren einachsialen Druckfestigkeit von 230 MPa (Medianwert) und einem GSI-Wert von 72-80. Die maximale In-situ-Spannung im Tunnel beträgt 65-85 MPa. Die Vorhersage von beobachteten Spannungsversagen werden weitergeführt indem man elastische 3-D-Simulationsergebnisse von Tunneln mit drei statistischen Fliesskriterien vergleicht. Read's oder Hoek's Fliesskriteria werden dabei als die relevantesten Kriterien angesehen, obwohl auch der Effekt der Anisotropie als wesentlich erachtet wird. Die wichtigsten Parameter für eine Korrelation von Spannungsversagen sind die Orientierung des Tunnels und die Schieferung der Gesteinsschichten. Desweiteren haben Gesteinsart, Tunnelprofil und geologische Anomalien ihren Einfluss. Ausserdem zeigt sich, dass eine Verzögerung bei der Kartierung die ausgeprägtesten Versagen deutlich verringern.

Jan 1, 2003

By Jack K. Lemley

This paper will provide an update of the Channel Tunnel Project including a discussion of the overall legal structure and management organisation. It is important to understand the mission that TML, as a design/build contractor, has undertaken and how the various interfaces have evolved between the other entities involved in the project. The paper will describe the evolution of the management organisation and the approach to completion of our contract, recapping the historic events and moving into a projection of how we will manage the completion of this very large transportation system.

Jan 1, 1991

By A. Arik

The accurate estimation of mining-block grades continues to be a challenging task for ore reserve practitioners. The estimation method used and the variability of the mineralization in the deposit are two factors that affect the accuracy of the estimates. The objectives of this study are to determine how different estimation methods perform on a given deposit and to determine the impact that the nature of the mineralization has on the results. A comparison of several estimation methods for prediction accuracy is performed based on conditional simulation results.

Jan 1, 2002

By N. Katsikaros, A. Lewis-Gray, P. Richards

"To optimize gold recovery in complex leach-to-electrowinning processes, Gekko Systems developed the Gekko resin exchange column (G-REX) as an intermediate step, using a highly gold-selective resin to isolate contaminant metals. The AuRIX®100 resin produced by Purolite is licensed exclusively to Gekko, with the G-REX column designed specifically for this resin. Operational experience has been gained at the Castlemaine Goldfields Ballarat gold mine. In near-continuous operation since 2008, the Ballarat plant treats unclarified concentrate leach solution. The extension of this technology to higher throughputs and more complex chemistry is discussed.RÉSUMÉ Afin d’optimiser la récupération de l’or dans des procédés complexes impliquant la lixiviation suivie de l’extraction électrolytique, Gekko Systems a développé la colonne Gekko de résines échangeuses d’ions (G-REX) comme étape intermédiaire, à l’aide d’une résine hautement sélective pour la récupération de l’or qui permet d’isoler les métaux contaminants. Gekko détient la licence exclusive pour la résine AuRIX®100 produite par Purolite, et la colonne G-REX a été spécifiquement conçue pour cette résine. C’est à la mine d’or Ballarat de Castlemaine Goldfields que l’expérience opérationnelle a été acquise. L’usine de Ballarat, en exploitation quasi-continue depuis 2008, traite une solution concentrée non clarifiée de lixiviation. L’extension de cette technologie à des capacités supérieures et à une chimie plus complexe est examinée."

Jan 1, 2017

By M. F. Dawson, S. B. Davis

SYNOPSIS This paper describes the size reduction of limestone smaller than 1 mm by attrition grinding, using quartz (1 to 3 mm) as the grinding medium in a laboratory rig. The ore and grinding medium were closely sized fractions, and the particle size of the grinding medium was at least three sizes larger than that of the ore. Batch tests showed that the size reduction of the feed followed two first-order rate processes: one for an apparently fast-breaking ore fraction, and a slower one for most of the ore (86 per cent). The production of fines (material smaller than 10 µm) followed a zero-order rate equation. Continuous runs showed that the process could be modelled as a perfectly mixed system provided that the discharge screen did not selectively retain coarser particles of ore. The ratio of medium to ore (both by mass and by volume) was found to have a significant effect, the most energy¬efficient grinding occurring at ratios between 1 and 2. The solids content of the slurry also had a significant effect, the greatest efficiency being obtained at 50 to 65 per cent solids (by mass). Within these energy-efficient ranges of medium-to-ore and solids content, the lower values resulted in maximum feed breakage and the higher values in maximum fines production. The most important factor in the breakage of feed was the difference in the particle size of the grinding medium and the ore; the amount of ore broken out of the feed size for a given energy input was found to increase linearly with the difference between the size of the grinding medium and that of the ore up to 2 mm. The production of fines increased similarly, but only up to a difference of about 1,2 mm, when it levelled off at about 5 kg/kW ? h. The mechanism proposed for attritioning is mainly the abrasion of 1 µm planes of limestone along the crystal axes, with some fracturing along existing lines of weakness. The energy consumption of nearly 200 kW ? h per ton of product smaller than 10 µm appears to be higher than that in other types of milling. It is concluded that the value of attrition milling lies in its selectivity; in this work, only the softer limestone and virtually none of the hard quartz grinding medium was comminuted.

Jan 1, 1989

By G Chitombo, G Lewis

The knowledge of the expected run of mine (ROM) fragmentation during the feasibility study of a green field site is essential for the design of downstream crushing and milling processes. However,the prediction of blast fragmentation can be a challenging process due to the uncertainty related to the blast design and rock mass parameters. In general,a number of possible blast designs are considered in a feasibility study,with factors such as bench height and blasthole diameter influencing the design. Rock mass parameters are normally derived from a limited number of geotechnical diamond drill cores. Although diamond drill core can provide detailed information concerning intact rock strength (unconfined compressive strength and point load),it provides limited structural information to predict the in situ block size distribution of the rock mass. The in situ block size is an essential input to the prediction of the fragmentation distribution, in particular the coarse end. This paper outlines the methodology of blast fragmentation modeling undertaken for a green field feasibility study at the Riska gold deposit in Indonesia. The favoured milling process for the feasibility study was dump leaching,with no crushing of the ore material extracted from the pit. For this reason,blast fragmentation was a critical issue to be addressed by the study. A range of blast designs were considered with bench heights and blasthole diameters ranging from 4 m to 7 m and 76 mm to 102 mm respectively. Rock mass data was obtained from 19 diamond drill cores across the deposit (total drill length approximately 2200 m). Intact rock strength was estimated from qualitative strength descriptors,while the in situ block size distribution of the rock mass was estimated from the Rock Quality Designation (RQD) of the core. The methodology of fragmentation prediction involved a number of steps including the estimation of rock mass parameters from diamond drillhole data including the estimation of the in situ block size, delineation of blast domains within the deposit,and the assessment of the impact of various blast design parameters and rock mass variation on the predicted fragmentation distribution. The modelling process for the Riska green field site highlighted the need for additional rock mass data to be collected post feasibility stage and once the development of the mine commenced.

Jan 1, 2004