Search Documents

By N. S. Tanious

This paper summarizes the results of an investigation into possibly the largest coal pillar failure in the USA. The newly opened drift mine is located in Southeastern Kentucky and worked an 11 feet thick coal seam, all other mines in the District worked seams 4-5 feet thick. The initial mine development consisted of 14 main entries (Fig. 1) which were driven in two sets of 7, under increasing depth of overburden. As the left seven entries came under deeper overburden the pillar ribs began sloughing which caused many of the concrete-block ventilation stoppings to crack. The mine management stopped the advance in the left seven and continued with the right seven entries. During the spring of the following year development resumed in the left seven, rib sloughage occurred again and this time severely cracked many stoppings and many were totally disintegrated from the excessive deformation. Within few weeks the sloughage was so heavy that many of these entries behind the active face were filled with piles of sloughed coal slabs. When the face reached a depth approximately 1150 feet, the sloughage became a slow, massive squeeze. The entry convergence (closure) reduced their height from 11 to 7-8 feet and the squeeze spread back to shallower depth covering an area roughly 300 pillars.

Jan 1, 1989

By Li. S., C. Sili

Abstract. Study on nonlinear damage localization process of rocks under water chemical corrosion is a more interesting topic in rock mechanics research world widely. It is very important in estimating long term stability of rock engineering, design of nuclear waste repository and its performance estimation, geothermal and petroleum development. This paper reports that new development of study on the topic, including methodology, results of meso-mechanical test, real-time CT scan test and acoustic emission test, temporal fractal behaviors, neural dynamic modeling and chemical-induced damage law, etc. This paper also discusses the research directions of the topic in the near future. Zusammenfassung. Untersuchung zum durch die chemische Corrosion induzierten Schaedigungsprozess ist einer der Trends im Gebiet der Felsmechanik. Sie ist zugleich ein sehr wichtiges Forschungsprojekt u.a. fuer geotechnische Langzeitstabilitaetsanalyse, Langzeitsicherheit eines Endlagers, Erdwaerme- und Erdoelfoerderung. Dieser Aufsatz stellt die neusten Entwicklungen in den folgenden Teilgebieten zusammen: Untersuchungsmethoden, Laborversuchsergebnisse der Mikromechanik, der Computer-Tomographie und der akustischen Emission, zeitabhaengige Fraktaleigenschaften, Modelle fuer die Nervendynamik sowie Modelle fuer chemie-induzierte Schaedigungen. Zum Schluss werden kuenftige Forschungsschwerpunkte bzw. –richtungen diskutiert. Résumé L’étude du processus de la localisation de l’endommagement du à l’érosion chimique est un thème d’actualité pour la mécanique des roches. Elle est également un sujet de recherche d’importance dans l’évaluation de la stabilité à long terme des ouvrages rocheux, l’analyse du system de stockage des déchets nucléaires et l’évaluation de son comportement, l’exploitation de l’énergie thermique et pétrolifère, etc. Cet article présente le développement actuel dans ce domaine, incluant la méthodologie d’étude sur le processus de la localisation de l’endommagement dû à l’érosion chimique, l’analyse des essais mécaniques avec l’observation microscopique, du balayage en temps réel (CT), et de l’émission acoustique. On aborde ainsi modèle des caractéristiques fractural du temps, le modèle de la mécanique dynamique neural, ainsi que la loi de comportement d’endommagement dû à l’effet chimique. Enfin, les perspectives relatives à ces études sont présentées et discutées.

Jan 1, 2003

Magneto flotation is a recently developed method aimed at simultaneous utilisation of the magnetic and flotation properties of minerals in separation processes. In this method, magnetic minerals are prevented from reporting to the froth product while non-magnetic minerals are being floated. With suitable ores, this makes it possible to reduce or entirely eliminate the cleaning and scavenging operations that are otherwise necessary in conventional flotation and magnetic separation systems. This paper describes the testing of magneto flotation on a Canadian magnetite ore. The ore sample used in the experimental work contained a total of 32.89 per cent Fe of which 87.60 per cent was magnetic in the form of magnetite. Magnetoflotation yielded, in a single step, a final concentrate assaying 69.10 per cent Fe and with an overall recovery of 84.84 per cent representing a magnetic iron recovery of 96.39 per cent. Comprehensive comparisons were made with conventional magnetic separation and flotation, and it was found that with these methods at least four processing steps were required to achieve results similar to those obtained with single-stage Magnetoflotation.

Jan 1, 1993

By Yuexin Han, Mu. Yufan, Yanjun Li, Peng Gao, Yongsheng Sun

"The objective of this study was to evaluate the effect of reduction temperature, reduction time and binary basicity on the size of metallic iron particles in coal-based reduction products of an oolitic iron ore. The particle size distribution behavior (i.e., cumulative passing percentage and mean size of metallic iron particles) during reduction was investigated in detail. Results showed that the particle size distribution of metallic iron particles was strongly influenced by reduction temperature, reduction time and binary basicity. The cumulative passing percentage and mean size significantly increased with reduction temperature and time in the entire range of the experiments. All curves of cumulative passing percentage versus particle size under different conditions demonstrated a similar trend (continuous increase). The size distribution parameters and mean size slightly increased with increasing binary basicity and significantly decreased when the binary basicity exceeded 1.0. The size of metallic iron particles could be controlled by adjusting the reduction conditions during coal-based reduction.IntroductionThe increasing demand for iron ore coupled with diminishing high-grade iron ore reserves has resulted in the urgent need for innovative technologies in order to use refractory iron ores. Oolitic iron ore is a typical refractory iron ore with tremendous abundance globally. Based on published literature, oolitic iron ore reserves are approximately 140 million tons in Europe, 10 billion tons in China and 66 million tons in Pakistan (Kazmi and Abbas, 2001; Wu et al., 2011; Yu and Qi, 2011; Sun et al., 2013a). Therefore, the efficient exploration and use of oolitic iron ore resources can play a significant role in easing the mineral resource crisis in the iron and steel industry. However, oolitic iron ore cannot be effectively upgraded by traditional beneficiation methods due to its mineralogical characteristics (e.g., low grade of iron, poor liberation of iron minerals and high phosphorus content) (Li et al., 2011b; Sun et al., 2013b).Researchers recently proposed coal-based reduction followed by magnetic separation to recover iron from refractory iron ores (especially oolitic iron ore) and a certain degree of breakthrough was achieved in both theory and practice. In this technology, iron minerals in the ore are directly reduced by coal to metallic iron, which grows into particles of different sizes. After comminution and liberation, metallic iron is concentrated by magnetic separation (Srivastava and Kawatra, 2009; Sun et al., 2013a; Li et al., 2011b; Sun et al., 2013b; Li et al., 2011c; Gao et al., 2013). Sun et al. and Gao et al. used this technology to examine the recovery of iron from oolitic and Bayan Obo iron ores, respectively (Sun et al., 2013a; Li et al., 2011b; Li et al., 2011c). Metallic iron powder with more than 90% iron content was obtained as the final product, which could be used directly in steel production."

Jan 1, 2015

One Hundred Sixteenth Meeting of the Institute, Monday, Feb. 18, to Thursday, Feb. 21, inclusive, 1918 A preliminary program, for the New York Meeting was printed in the January Bulletin, and a more detailed program was mailed to all members early in January. The following schedule is the outcome, of sundry committee meetings up to the middle of January. Committee on Arrangements J.` E. JOHNSON, JR., Chairman BRADLEY STOUGHTON, Vice-Chairman RALPH W. DEACON MRS. S. J. JENNINGS E. M. SHIPP J. V. N. DOER A. R. LEDOUX G. D. VAN ARSDALE L. `V. FRANCIS . . F. T. RUBIDGE ARTHUR L. WALKER Summarized Program MONDAY, FEBRUARY 18 9 a. m. to 5. p. m. Registration at Institute Headquarters. 10 a. m. Sessions on Coal and Non-Ferrous Metallurgy. 12.30 p. m. Luncheon at Engineering Societies'. Building. 2 p. m. Visit to Subway Workings.

Jan 2, 1918

By E. Busse, J. E. Burgener, J. G. Eacott, M. C. Robinson, P. E. Burgener

"This paper presents a preliminary assessment of the technical and economic feasibility of a caustic leach - electrowinning process for the recovery of zinc and lead from electric arc furnace baghouse dust at a mini-steelplant. Recent studies and literature are referenced briefly as they pertain to the formation and characterization of dust, toxicity considerations and alternative dust treatment and disposal options.Laboratory testwork results, published data, pilot plant experience and anticipated influences resulting from recycling residues are used for the purpose of developing a conceptual design for a caustic leach - electrowinning plant to treat 15,000 tonnes/year of dust at a one million tonnes /year capacity steelplant in Canada.Target economic studies, comprising preliminary estimates of capital and operating costs, revenues and rate of return are presented. Economic and commercial considerations concerning the relative merits of dust treatment at a centralized facility compared with an on-site plant are discussed.IntroductionThe treatment or disposal of mini-steelplant electric arc furnace (EAF) baghouse dust has been given increasing attention in recent years for two principal reasons. Firstly, the dust is now classed as a hazardous waste material under V.S. EPA regulations which prohibit its disposal in dumps other than controlled landfill sites. Secondly, the dust contains certain metal values, notably zinc and lead, which may be economically recoverable, depending on the costs associated with disposal resulting from enforcement of the EPA regulations. Other metallurgical dusts and waste materials, from both ferrous and non-ferrous operations, may require the same considerations as EAF baghouse dust.Several studies have been carried out to examine various aspects of dust treatment but few commercial plants are in operation. Technology employed uses pyrometallurgical techniques. Commercial-scale hydrometallurgical plants are not known to exist although small-scale plants are frequently more economically attractive than their pyrometallurgical counterparts which generally require economies of scale to be viable.The concentration of mini-steelplants in northeast V.S.A. and southeast Canada merits study to determine whether or not dust treatment for metals recovery is a commercially feasible alternative to disposal.This paper examines the technical and economic feasibility of a caustic leach - electrowinning process for the recovery of zinc and lead from EAF baghouse dust at an on-site ministeel plant processing carbon steel scrap and discusses economic and commercial considerations pertaining to dust treatment at a larger, centralized facility."

Jan 1, 1984

By Clark I, Stockton N, Warren L

Nickel flotation circuits currently experience difficulties in recovering fine particles of pentlandite less than ten microns. By agglomerating these particles using shear-flocculation it is hoped to improve the recovery of these fine particles. A sample of massive sulphide ore from the Kambalda region was separated using magnetic separation to obtain a high grade pentlandite concentrate (> 90 per cent). This was finely ground to produce a sample with particles of 50 per cent minus 10 um in size. This sample was then shear-flocculated using a variety of reagents, including xanthates, dithiophosphate and mercaptobenzothiazole (MBT). The effects of reagent type and concentration, conditioning time, impeller speed and type, and pulp density were studied. Froth flotation tests were also conducted on the shear flocculated pulps to compare the effects of xanthate and MBT on the recovery of pentlandite.

Jan 1, 1992

By Charlie Harper

Open Pit Mining of Golden Band Resources? EP Gold Deposit Golden Band Resources Inc. (GBN:TSX-V) is Saskatchewan's newest Gold Producer. Located in the La Ronge Gold Belt of northern Saskatchewan, GBN has over 875 km2 of claims with 12 known gold deposits and 4 former producing mines. Production has begun at the Roy Lloyd Mine (Bingo Deposit), to be followed initially by our EP and Komis properties. Development of the underground infrastructure at the Roy Lloyd Mineis continuing and on schedule. Production from these deposits will feed our centrally located and 100% owned Jolu mill. We have our provincial environmental permits in place, and we have an established infrastructure including a 400 tonne-per-day mill, year-round road access, and access to grid power. Construction of the grid power line and the above ground tailings facility are now complete.

Nov 1, 2011

By A. L. Field

Previous Publications THE first report on the slag viscosity work of the Bureau of Mines was made by one of the authors 1 in 1916. It was concerned chiefly with, the method of measurement. A paper 2 on this phase of the work was presented to the Institute in February, 1917, and a similar paper 3 was communicated to the Faraday Society. Purpose and Scope of the Slag Viscosity Tables Following the development of a suitable method, the next step in the investigation was the measurement of slag viscosity over a wide range of temperature and composition, and the arrangement of this experimental data in the form of tables for the use of the blast-furnace operator. It is believed that this information, if used intelligently, should help the operator to reduce losses in production caused by off-grade pig iron, to improve fuel economy, to promote operating efficiency, and to extend present-day practice to meet the increasing need of smelting lean and complex ores. In the experimental part of the work it was early observed that the temperature-viscosity relations of a slag were determined, for practical purposes, by the relative proportions of the three major constituents, lime (CaO), alumina (Al203), and silica (Si02), provided the percentage

Jan 12, 1917

By A. L. Field, P. H. Royster

The first report on the slag viscosity work of the Bureau of Mines was made by one of the authors1 in 1916. It was concerned chiefly with the method of measurement. A paper2 on this phase of the work was presented to the Institute in February, 1917, and a similar paper3 was communicated to the Faraday Society. PuRpose and Scope of the Slag Viscosity Tables Following the development of a suitable method, the next step in the investigation was the measurement of slag viscosity over a wide range of temperature and composition, and the arrangement of this experimental data in the form of tables for the use of the blast-furnace operator. It is believed that this information, if used intelligently, should help the operator to reduce losses in production caused by off-grade pig iron, to improve fuel economy, to promote operating efficiency, and to extend present-day practice to meet the increasing need of smelting lean and complex ores. In the experimental part of the work it was carly, observed that the temperature-viscosity relations of a slag were determined, for practical purposes, by the relative proportions of the three major constituents, lime (CaO), alumina (Al2O3), and silica (SiO2), provided the percentage

Jan 1, 1918

By K. Janghorban

Multilayered ceramic-metal composites were produced by solid state diffusion bonding of polycrystalline alumina and three Al alloys containing 1 to 2%Sr, 2% Mg and Mg + Si (5057 Al alloy), The multilayered structures were fabricated at 610°C under a compressive stress of 3 MPa for 2 hours in He-5%H atmosphere, The ceramic-metal interfaces were studied by SEM and TEM equipped with energy dispersive spectrometer (EDS). Addition of 1 wt % Sr to Al promoted good adhesion, without producing any interfacial products, while the Al-2%Sr was poor in this regard due to the presence of dispersed A14Sr which is an intrinsic phase in the Al-Sr phase system, The Al-2%Mg alloy produced a continuous film at the interface, which was characterized to be MgAl2O4. Al alloys containing Mg and Si (5057 commercial alloy) produced not only the spinel structure (MgAl2O4), but another phase rich in Mg and Si (close to Mg2Si), These latter interfacial reaction products were not the intrinsic phases in Al-Mg alloys, and were reaction products at the Al2O3 ?Al alloy interfaces.

Jan 1, 2005

By Gabriel S. Esterhuizen

"Cable bolts are sometimes used in low-seam coal mines to provide support in difficult ground conditions. This paper describes cable bolting solutions at two low-seam coal mines in similar ground conditions. Both mines used support systems incorporating cable bolts as part of the primary support system. Two original cable bolt based support systems as well as two modified systems are evaluated to estimate their ability to prevent large roof falls. One of the support systems incorporated passive cable bolts, while the other used pre-tensioned cable bolts. The results and experience at the mines showed that the modified systems provided improved stability over the original support systems. The presence of the cable bolts is the most important contribution to stability against large roof falls, rather than the details of the support pattern. It was also found that a heavy steel channel can improve the safety of the system because of the ‘sling’ action it provides. Additionally, the analysis showed that fully-grouted rebar bolts load much earlier than the cable bolts, and pre-tensioning of the cable bolts can result in a more uniform distribution of loading in the roof.INTRODUCTIONCable bolting is sometimes used as primary support in coal mines experiencing difficult roof conditions. In low-seam mines the flexibility of the cable bolts allows greater length supports to be installed near the advancing face without the use of couplers. When used as primary support, the cables are typically installed in the same row as fully grouted bolts, replacing two or more of the bolts in each support row. A heavy steel channel may be used as a strap to spread the support load over a greater portion of the roof. Historically, the Mine Safety and Health Administration (MSHA) has not allowed widespread use of partially grouted un-tensioned bolts (e.g., passive cable bolts) for primary support; however, pretensioned cable bolts have been accepted.Various solutions using cable bolts as primary support were attempted at two low-seam coal mines in Western Pennsylvania that were experiencing difficult roof conditions. Both mines originally used fully grouted rebar bolts as primary support and cable bolts as supplementary support. It was found that when a large roof fall occurred, the cable bolts may be contained within the dome of fallen rock. As problematic roof conditions continued to exist, both mines decided to use cable bolts as part of the primary support system. The cable bolts were located near the ribs of the entry, to increase the likelihood that they would be anchored outside the dome of potentially unstable roof. The cable and rebar bolts were installed on a heavy steel channel that acts as a ‘sling’ to distribute the load across the width of the entry. At the first mine, Mine A, pre-tensioned cable bolts were used while at Mine B, un-tensioned cables were used. The two support systems consist of essentially the same support components installed in different patterns and with varying degrees of pre-tension."

Jan 1, 2015

By Yingxin Zhou

Data from these field studies and previous case study data have been combined to define ultra-dose seam mining environments and relate them to observed failure conditions. A rating system for ultra-close multi- seam design has been developed and field studies have verified the applicability of the design criteria according to geologic structures, lithology and spatial data. This rating system has been combined with design and depth considerations to create a protocol for quantitatively predicting potential damage in ultra-dose seam mining conditions. A brief discussion of the characteristics of ultra-dose seam mining and its related failure mechanisms is also presented

Jan 1, 1990

By Philip Kraft

WHEN it came time to write a biography of Philip Kraft, we got out a copy of Bartlett's "Familiar Quotations" and looked through the references to Travel, Traveled, Traveler, and Traveling, feeling sure there would be some reference to Mr. Kraft. Sure enough, we found: "Travel, in the younger sort, is a part of education; in the elder, a part of experience." Had Francis Bacon done his writing three and a half centuries later, Mr. Kraft might well have served as the inspiration for that sentence. New Yorker born, he received his B.S. and E. M. degrees from Columbia. In 1912, then 22 years old, he took off for Germany where he spent two years studying at the Royal School of Mines, Berlin, for his Doctor of Engineering degree. Contrary to the Greeley-Soule precept, Mr. Kraft, on his return from Europe, went north to South Porcupine. Ont., working as geologist and mining engineer for the Dome Mine. From South Porcupine his next stop was Washington, D. C., where, during the years the country was in the first World War, he was engaged in war work.

Jan 1, 1947

By Gary Carmack

Overview: Public awareness of the drug abuse problem within the government and industry is growing each day. The economic cost to industry is staggering-estimated to be more than $50 billion per year. Employee drug testing programs are one way to combat the problem, yet they are not without legal and scientic pitfalls. Some of the issues and needs that should be considered before implementing or continuing a testing program are: Why test? What do you test for? Are the results accurate? What impact will the new Federal Rules have? Accuracy of the testing continues to be controversial, especially when the "poppy-seed" and "cold-medications" issues are mentioned. The new Federal laboratory certification program which is about to start, should reduce or eliminate the question of lab error. Determination of on the job impairment will, however, continue to be a problem.

Jan 1, 1988

By O. Bazhko

Regular analysis of different streams is important for the control of hydrometallurgical processes. Various physical and physical-chemical methods are applied for this purpose. Many modern methods require costly equipment and are subject to interferences. Therefore, redoxtitration methods remain of interest. The use of different types of oxidizing and reducing agents as well as redox indicators enables many cations and anions to be rapidly and accurately analysed. Sometimes redox titrations require the prior preparation and addition of masking agents. Selective, sensitive and low-cost methods of redoxtitration of copper and SO2 in plant conditions are described.

Jan 1, 2009

By R. Y. Wan, Corby G. Anderson, L. Ernest Krys, M. C. Fuerstenau

Since 1942, refractory precious metal concentrates at the Sunshine mine have been processed for antimony metal recovery using a novel leach-electrowin method. This is counter to most antimony production facilities where pyrometallurgical techniques are usually relied upon. The key step for removal of the antimony has been an ambient pressure alkaline sulfide leach. In 1990, a comprehensive laboratory study was undertaken to better understand this process. Factors studied included temperature, agitation, concentrate regrind, alkaline species concentrations, sulfur species concentrations and solids concentration. Details of these studies, as well as a brief description of Sunshine metallurgical processes, will be presented.

Jan 1, 1993

By M. J. A. Ruszala

Aggregates production is a huge global industry which uses an enormous amount of energy and produces a massive amount of unsalable fines. Reducing the amount of energy used per tonne of product and/or the amount of fines produced, would make a quarry more efficient. This reduction would make the quarry more environmentally friendly and profitable. This research looks at modelling Mountsorrel Quarry, a granite quarry in the United Kingdom (UK), using JKSimMet and Split-Desktop software packages in conjunction with the European Union (EU) project, EE-Quarry. Samples submitted to drop weight tests confirmed Mountsorrel Quarry granite as an extremely hard granite. Rock fracture data (t10) and energy of comminution (ECS) data were obtained from analysing the results. Split-Desktop image analysis software was utilized to determine the particle size distribution (PSD) of the primary crusher feed, as it contains particles too large to screen manually. It was also found that <1% of the feed is fines, which at Mountsorrel Quarry are classed as particles smaller than 5 mm, and that no particles were larger than 3,810 mm. JKSimMet was used to create a flowsheet of Mountsorrel Quarry. The crusher product PSDs were simulated and found to have strong correlations with experimental data, calculated by screening samples from conveyor belts, especially in the fines region, with a mean difference of 1%. The simulated primary crusher product PSD showed that it contains ~6% fines. A simulation over the entire quarry showed the product to be within the size range produced at Mountsorrel Quarry, and with a simulated fines content of 13%. When the CSS on the primary crusher was altered from 165.1 mm (the operating size on site) to 100.0 mm, it increased the overall percentage of fines produced by 3%, increased the power draw by 140.6 kW, but reduced the overall plant production percentage of fines by 2%. Two blasts were analysed on adjacent rock faces. They had identical blast designs, but the order of deck detonation varied; the first blast detonated the bottom deck before the top and vice versa in the second blast. For each blast, measurements of the feed PSD to the primary crusher, the number of particles that required secondary breakage on the quarry floor, acoustic levels and vibration readings were measured. No significant difference was identified between the two blasts in any of the parameters measured. In conclusion, a working model of Mountsorrel Quarry has been made in JKSimMet that has been validated against data from site and Split-Desktop has been used to simulate the primary crusher feed PSD, something that was previously unknown. The effect of reversing the order of deck detonation in a two deck blast was also analysed but with no significant difference between the two blasts found.

Aug 1, 2013

By Don B. Carson, Donald L. Katz

NATURAL gases under pressure form crystal-line hydrates with water. Experimental data are reported on four-phase equilibrium for the methane-propane-water, methane-pentane-water, and methane-hexane-water systems. Temperatures and pressures for equilibrium between gas, water-rich liquid, hydrocarbonrich liquid, and hydrate were measured, as well as the percentages of methane and propane in the hydrate. The data indicate that natural gas hydrate behaves as a solid solution and that pentanes and heavier hydrocarbons do not enter into the solid phase. Vapor-solid equilibrium constants are presented that permit the approximation of the conditions for hydrate formation, from the composition of a gas. INTRODUCTION Natural gas hydrates have been the object of considerable research in recent years, because of the trouble they have caused in the natural-gas and natural gasoline industries. Natural gas hydrates are white crystalline compounds of water and gas, which, under pressure, exist at temperatures considerably above the freezing point of water. Because of the relatively high temperatures at which the hydrates exist, they become a nuisance in high-pressure gas operations where water is present, since their formation causes partial or complete plugging of valves and pipes. From a practical standpoint, the trouble incident to hydrate formation has been solved by dehydration of the gas before it enters the plant or pipe line, or by other remedial measures. Extensive work on gas hydrates in the latter part of the nineteenth century, by Villard1 and others, gave data on methane hydrate and on ethane hydrate. Schroeder summarized these theoretical studies.2 Hammerschmidt3 introduced the information on gas hydrates to the gas industry and Deaton and Frost4-6 gathered a considerable number of data on the behavior of natural gas hydrates. Recent papers7,8 have extended both the data and the theory of these hydrates. At present, data are available on temperatures and pressures of hydrate formation for pure methane, ethane, propane, n-butane, methane-ethane mixtures, methane-propane mixtures, methane-butane mixtures, and some 15 natural gases, all in the presence of excess water. However, up to the present time no method has been available for predicting the temperature at given pressures or the pressure at given temperatures at which natural gases will form hydrates if saturated with water. This paper pre¬sents data on the methane-propane-water, methane-pentane-water and methane-hexane water systems in four phases, one of which is the hydrate. The application of the phase rule to the methane-propane-water data proves that hydrates behave as solid solutions. The data of this paper and those in the literature were used to develop vapor-solid equilibrium constants,8 which permit prediction of conditions of hydrate formation from the analysis of a natural gas.

Jan 1, 1941

By A. May

Florida has accumulated about 400 million tons of phosphogypsum, a mineral process waste generated in the production of fertilizer, and is adding 30 million tons to this annually. To minimize storage of this waste and reduce potential environmental effects, the Bureau of Mines conducted research into utilizing the phosphogypsum, by identifying and developing high-volume uses for this material. Admixtures of phosphogypsum, fly ash, and lime that could produce a coarse aggregate suitable for road construction were investigated. Using phosphogypsum with asphalt, cement, cement-kiln dust, silica, clays, and oxychlorides to pro-duce aggregate was also examined.

Jan 1, 1985