Search Documents

By B. C. Williams

The Bureau of Mines monitored the water quality in and near a copper/gold tailings impoundment. Samples were taken from the unsaturated %one. and dissolved concentrations of over ZO constituents were measured with respect to depth and moisture content, factors which influence oxygen content and sulfide oxidation. Samples from the unsaturated %one were drawn through a hypodermic needle sampler into individually evacuated vials fitted with septa, thus preventing oxygen contamination. Water quality was also monitored in the saturated tailings, underlying colluvial aquifer, and weathered andesite bedrock.

Jan 1, 1989

By Deborah A. Kopsick

Several minerals were observed and collected in a small gully originating from a weathered coal processing waste (gob) pile in Barton County, Missouri. The rapid alteration of these various minerals after collection suggested that they might represent a dehydration sequence. X-ray diffraction of the dehydrated and rehydrated minerals deposited on the gob pile indicated the presence of the monohydrate and heptahydrate forms of ferrous sulfate, szomolnokite and melanterite respectively. The occurrence of melanterite (FeSO4.7H2O), was limited to isolated areas of ponded water while szomolnokite (FeSO4.H2O), was associated with the outwash areas of the pile. Laboratory dehydration of melanterite collected at the gob pile revealed the formation of rozenite (FeSO4.4H2O), an intermediate form of ferrous sulfate. Szomolnokite was shown to be the stable form of these ferrous sulfates during these experiments while melanterite and rozenite were shown to alter readily. Chemical analysis of szomolnokite revealed enrichment in Fe, Mg, Zn, Cd, Cu and Mn relative to the chemical composition of the gob ad the lechate generated from the gob wastes. Although this gob pile had been weathering for more than 35 years, significant concentrations of trace metals were still being released from the pile through the generation of leachate and the formation of various soluble metal enriched ferrous sulfate minerals.

Jan 1, 1982

By Travis Q. Lyday

Australia was one of the world's principal producers of minerals and metals, and its minerals industry was a leading catalyst in promoting growth of the country. Australia was the world's largest producer of alumina, bauxite, diamond, ilmenite, monazite, opal, rutile, sapphire, and zircon. It was the premier exporter of alumina, coal, ilmenite, refined lead, monazite, rutile, and zircon, and was the second leading exporter of iron ore, after Brazil. Ranking behind China, the United States, the U.S.S.R., the German Democratic Republic, Poland, and the Federal Re-public of Germany, Australia was the seventh largest producer of coal (all grades) in the world. Australia was the fourth largest gold producer in 1988, after the Republic of South Africa, the Soviet Union, and the United States. It was the second largest producer of zinc, the third largest producer of nickel, the fourth largest producer of uranium, and the seventh largest producer of copper. 2 The country's mineral wealth was so extraordinary that it was virtually self-sufficient in most mineral commodities. Endowed with abundant resources of coal, natural gas, liquefied petroleum gas, and uranium, Australia was one of the few market economy countries that was a net exporter of mineral fuels. About 90% of Australia's consumption of crude oil was supplied by domestic production; this was expected to decline significantly about 1990, unless significant new oilfields were discovered.

Jan 1, 1990

By R. M. Owens, J. F. Lupo

The Shirley Basin Uranium mine, located in southeastern Wyoming, USA, was an open pit mining operation consisting of a series of several open pit mines excavated into poorly consolidated sandstones, siltstones, and claystones. Since the initial open pits were developed in 1969, slope failures have plagued the mine and mining operations. These slope failures have persisted into the current mine reclamation period. When the mine was first developed, the open pit slopes were designed to range between 45 to 55 degrees. Numerous slope failures during mine development required the pit slopes to be redesigned with slopes as shallow as 26 degrees. At present, movements are occurring within the open pits on reclaimed slopes that are shallow as 12 degrees. Several detailed slope studies were conducted at the mine in the early 1970s. These studies, combined with more recent geotechnical investigations, provide a unique detailed history of pit slope failures on shallow slopes. This paper presents an evaluation of the slope failures at the Shirley Basin mine, highlighting important mechanisms causing slope failures on very shallow slopes. The evaluation demonstrates important key parameters for shallow slope design.

Jan 1, 2001

By N. Langsford

The Archaean Yilgam craton has been a major gold province since 1888 with production and reserves of about 4700 tonnes. Production in 1994 was about 135 tonnes. The largest deposit, the famous Kalgoorlie Golden Mile, contains about 2000 tonnes of gold. About 40 deposits containing more than 35 tonnes (1Moz) of gold has been discovered so far in the Yilgarn. Most of the craton has deep weathering profiles inherited from previous tropical climatic conditions, modified by subsequent arid conditions. A mantle of transported material covers much of the variably stripped weathering profiles. Resolving the geology of the volcanic-sedimentary units (greenstones) and the structures that host the gold mineralization relies heavily on aeromagnetics and shallow drilling.

Jan 1, 1995

The Institute has prepared a list of Societies' publications, magazines, . etc., which were duplicates and were discarded at the time of the consolidation of the libraries of the three Founder Societies. These books will be disposed of about March 1, 1916 by the Board of Directors of the Institute through the Library Committee. If, meanwhile, members who have incomplete sets of these books, or for any other reason desire to secure some of them, they are asked to communicate immediately with the Secretary, as this is in unusual opportunity to secure books at a very low price. American Gas Light Journal, viols. 31 to 39. American Institute of Electrical Engineers, Transactions, vols. 5 to 26. American Machinist, vols. 3 to 20, 22 to 29. American Society of Civil Engineers, Transactions, vols. 2 to 10, 21 to 24, 26 to 33, 39 to 49, 52, 55, 58, 74. Index, viols. 1 to 21. American Society of Mechanical Engineers, Transactions, vols. 1 to 28. Index, vols. 1 to 20, vols. 1 to 25.

Jan 1, 1916

By Cyril Smith

THE following table, which is composed of data given in the author's first paper on the thermal conductivity of copper alloys1, contains the results which have been obtained by previous workers on the thermal conductivity of the copper-tin, the copper-phosphorus and the copper-tin-phosphorus alloys (the phosphor bronzes). TABLE 1.-Previous Investigations Composition, Per Cent. by Weight Thermal Conduc¬ Investigator tivity, Cal/Sq. Cm./ Copper Tin Phosphorus CM./Sec.. °C. Hardebecka 95.0 5.0 0.176 (20° C.) Grossmanb 90.1 9.9 0.105 75.5. 24.5 0.059 24.9 75.1 0'.139 (13° C.) 9.7 90.3 0.131 0.0 100.0 0.142 Griffiths and Schofieldc 91.7' 8.0 0.30 0.108 87.2 12.4 0.40 0.087 (20° C.) 90.0 10.0 Small amt. 0.100 Donaldsondd: 87.8 1 11.3 0.35 0.128 Pfleiderere 99.4 1 0.63 0.250 (30° C.) 98.0 1.98. 0.125

Jan 1, 1930

By P. Seethalakshmi, Yatakuri Yaswanth Naidu

The use of a single pile, group of piles with pile cap, piled raft foundation system, etc., are prevalent in transferring the superstructure load from the soft soil layers to the firm underground layers to reduce the settlement and improve the bearing capacity. The recent development of disconnected piled raft foundation has gained greater importance in improving the load transfer mechanism among the pile, raft, and subsoil by reducing the vulnerability of the greatest axial force on the pile head which leads to pile failure. The present study aims at analyzing the performance of unreinforced and Geogrid reinforced disconnected piled raft foundations under vertical loading using the commercially available finite element software PLAXIS-3D. A parametric study was conducted on unreinforced and reinforced disconnected piled raft foundations to explore the effect of varying pile stiffness as well as the inclusion of Geogrid layer on the load vs settlement, the load sharing ratio of piles and raft, and the distribution of axial load and bending moment along the length of the pile. The Mohr-Coulomb model was used for the granular cushion layer while the Modified Cam Clay model was used for soft clay underlain the sand layer. Raft and piles were assumed to be rigid and linear elastic. The results showed that axial force taken by piles with higher stiffness was maximum while settlement at the bottom tip of the pile with higher stiffness was maximum in both reinforced as well as unreinforced disconnected piled raft systems.

Sep 1, 2022

By Hennie F. T. Barnard

Where geotechnical designs are governed by settlement requirements, soil and rock moduli are important parameters for design. This paper reports on a method that was used to utilize dynamic modulus measurements in the field toward pile settlement designs for the proposed Square Kilometer Array (SKA) Project to be located near Carnarvon, South Africa. The project will comprise of over 3000 No. movement sensitive satellite dish structures. The method described in the paper utilizes strain-related modulus degradation across the complete ground profile, starting from measurements of peak particle velocity (and inference to dynamic modulus at small strain) as measured using Continuous Surface Wave (CSW) testing at individual dish positions. This is required due to the very small allowable foundation rotation of 5 arc seconds under the dishes? operational conditions. The strategy of analysis was to conduct an iterative process starting from the measured small strain modulus profile of the ground. The likely maximum pile force for a specific piled foundation option was estimated and a single pile finite element analysis was performed using Plaxis 2D (Version 2010) to estimate the expected ground strain developing along the length of the pile. By assuming the shape of the shear modulus degradation curve with increasing shear strain, the iteration process then converged on a likely degraded modulus profile associated with the single pile and maximum load assumed. This process enabled identifying the pile cap size, pile configuration, pile sizes and pile lengths that would meet the operational movement limits. The chosen pile group configuration was then analyzed using the Repute 1.5 pile group analysis software. The design process and typical results are discussed in this paper.

By Hennie F. T. Barnard, Theodore E. B. Vorster

Where geotechnical designs are governed by settlement requirements, soil and rock moduli are important parameters for design. This paper reports on a method that was used to utilize dynamic modulus measurements in the field toward pile settlement designs for the proposed Square Kilometer Array (SKA) Project to be located near Carnarvon, South Africa. The project will comprise of over 3000 No. movement sensitive satellite dish structures. The method described in the paper utilizes strain-related modulus degradation across the complete ground profile, starting from measurements of peak particle velocity (and inference to dynamic modulus at small strain) as measured using Continuous Surface Wave (CSW) testing at individual dish positions. This is required due to the very small allowable foundation rotation of 5 arc seconds under the dishes’ operational conditions. The strategy of analysis was to conduct an iterative process starting from the measured small strain modulus profile of the ground. The likely maximum pile force for a specific piled foundation option was estimated and a single pile finite element analysis was performed using Plaxis 2D (Version 2010) to estimate the expected ground strain developing along the length of the pile. By assuming the shape of the shear modulus degradation curve with increasing shear strain, the iteration process then converged on a likely degraded modulus profile associated with the single pile and maximum load assumed. This process enabled identifying the pile cap size, pile configuration, pile sizes and pile lengths that would meet the operational movement limits. The chosen pile group configuration was then analyzed using the Repute 1.5 pile group analysis software. The design process and typical results are discussed in this paper.

Jan 1, 2017

By Karen Dawson, Qiang Li

Unreinforced displacement augercast piles, or rigid inclusions (RIs), were installed for foundation support of a combined sewer overflow treatment building. The RIs penetrated loose silty sand and soft silt and terminated in medium-dense to dense silty sand, approximately 40 ft below grade. The building houses water-holding basins and level-sensitive weirs and equipment. Strain gage-instrumented static axial load tests and low strain pile integrity tests (PIT) were conducted on the RIs as part of quality control for this technology. Strain gage monitoring continued during the installation of the remaining production RIs, construction of the building, and water preloading of basins and channels within the building. While the composite RI-reinforced ground and load distribution mat system performed as expected for settlement control and was not needed for lateral support, RI fractures as observed by PIT in this project might need to be controlled in other situations. Case history information regarding the subsurface fill and deltaic deposit character, RI installation production rates, RI testing procedures and results, and construction settlement monitoring are presented.

Oct 31, 2023

By E. M. Frizzell

This paper addresses the use of the microcomputer programs BACKONE and BACKWEDG for an estimation of rock mass strength characteristics by back analysis of plane and wedge failures. The artificial support requirements are also determined by the programs PLANE2, BOLTPAT, and BOLTWEDG in terms of rock anchor installation angles, tensions, and installation patterns. These programs have been combined into a package called BACKPACK, which can be applied in open pit mines where some failures have already occurred.

Jan 1, 1988

By G. S. Rice

Undoubtedly there is a serious problem through the juxtapostion of gas and oil wells and coal mines, not only at the present time, but possibly of far more serious import for the future.

Jan 1, 1915

By D. F. Kaufman, V. V. Damiano, G. J. London, L. R. Aronin

Beryllium bicrystals were Prepared by a seeding and floating zone-melting technique from high-purity beryllium single-crystal material. The starting material was given six floating zone purification passes prior to producing the bicrystals. Symmetric, asymmetric, and antisymmetric bicrystals were tested in tension. Included were bicrystals with boundaries both parallel and perpendicular to the tension axis. Modified symmetric bicrystals were also examined in detail. In these cases, the angles made by the slip planes with the boundary were not equal. Failure by (0001) cleavage, (1180) cleavage, and boundary separation were all observed depending on the orientation of these cleavage planes and the boundary with respect to the tension axis. Failure occurred on whichever system experienced the greatest normal stress. The origin of the fractures observed and the operative dislocation mechanisms were investigated by frac-tography and transmission electron microscopy. The results indicate that low-angle boundaries form in close proximity to the bicrystal boundary and act as sites for crack nucleation. It has been concluded that, although macroscopic compatibility was satisfied in many of the bicrystals examined, the bicrysta1 boundary was effective in Producing "early" failure by local bend plane formation as plastic deformation proceeded, followed by cleavage initiation and crack propagation. SINGLE crystals of high-purity beryllium oriented with the basal plane inclined 45 deg to the tension axis exhibit a critical resolved shear stress of about 300 psi and 200 pct extension by slipping only on the basal plane before failure by cleavage on that plane. Single crystals, oriented with the basal plane parallel to the tension axis, deform by prism slip at a critical resolved shear stress of 9000 psi and exhibit an extension of over 100 pct before failure in a ductile manner.' In contrast to the behavior of single crystals, poly-crystalline beryllium deformed in tension or bending exhibits little or no ductility at room temperature. Beryllium's lack of ductility at room temperature has been attributed to its lack of a sufficient number of independent slip systems. Beryllium has only four independent slip modes at room temperature and according to the Taylor2 and von Mises3 criteria at least five independent shear modes are necessary to completely satisfy the strain compatibility conditions at all the boundaries in a random polycrystalline sample. Studies of beryllium bicrystals thus appear to provide a convenient way in which to determine whether the condition of strain compatibility is a necessary and sufficient condition to prevent failure and whether obviously incompatible boundary conditions result in boundary separation. Bicrystal studies, although not providing all of the constraints encountered in polycrystalline samples, do allow one to select very specific orientation relation-

Jan 1, 1969

By D. Markwart, B. Volk

Anode effects are a phenomenon of the aluminium electrolysis process which produce potent greenhouse gases called PFCs (CF4, C2F6). With concerns surrounding global warming, and increasing regulation of GHG emissions, anode effects have become a significant sustainability issue for aluminium producers. In modem smelters, sophisticated computer control and automated alumina feeding systems allow for very tight control of the alumina concentration in the electrolyte and thus very low anode effect frequencies. Older smelters, however, do not have these systems and must either invest heavily to obtain them, or find other, innovative ways to reduce anode effect frequency. This paper will present the integrated approach to anode effect reduction used in the Vertical Stud Soderberg (VSS) potlines at Kitimat Works. Through an innovative combination of simplified signal analysis, modified alumina feed control logic, anode effect prediction, and anode effect prevention using a pager based communication system, Kitimat W arks has been able to make significant reductions to its anode effect frequency.

Jan 1, 2006

By Judith L. Bolis

The Bureau of Mines estimated the potential availability of iron ore from 129 domestic and foreign mines and deposits in 25 market economy countries. The availability of four products on a total and regional basis was determined from demonstrated resources of 75.3 billion It. From the resources evaluated there are a total of 18.6 billion It of sinter fines, 4.9 billion It of lump ore, 14.7 billion It of pellets, and 820 MMlt of pellet feed potentially available at a 15-pct DCFROR, f.o.b. port. On a regional basis, at or below a total cost of $0.26 per iron unit there are 1.7 billion It, 2.8 billion It, and 186 MMlt of sinter fines potentially available from Brazil, Australia, and Africa, respectively. There are 825 MMlt of lump ore from Brazil and 1.4 billion It from Australia potentially available at or below a total cost of $0.24 per iron unit. There are 2.1 billion It of pellets potentially available from the United States at or below a total cost of $0.80 per iron unit, while 442 MMlt are potentially available in Brazil at or below $0.38 per iron unit. South America has 208 MMlt of pellet feed potentially available at or below a total cost of $0.28 per iron unit. While the resources of iron ore are more than adequate to satisfy demand, the future of the iron ore industry is very dependent upon changes in the world economy, and on the domestic scene, changes in the domestic steel industry and steel imports.

Jan 1, 1987

By J. E. Doo1ey

To process and use the heavy ends of petroleum effectively, the development of suitable separation and characterization procedures not currently available was required. A systematic procedure was developed by the Bureau of Mines using such techniques as isothermal and molecular distillation, chemical treatment, silica-alumina gel chromatography, gel permeation chromatography, and spectrometry. Using these techniques, the Bureau achieved a detailed separation and characterization of a 370° to 535° C distillate from Gach Saran, Iran, crude oil. Such a systematic procedure and the semiquantitative data resulting therefrom should be of value in selecting feedstocks and in optimizing petroleum processing operations.

Jan 1, 1973

By Brent Robertson

Failure to meet quality objectives during the execution of any industrial project has lasting negative impacts on facility life cycle performance. Cost overruns, schedule delays, and rework are characteristics of project quality issues that arise during the project. Commissioning and start-up problems, low production, production bottlenecks, breakdowns and the necessity for operational work-arounds are characteristics of project quality issues that appear after project completion. Risks such as production facility downtime, shortened equipment life, and potential HSE violations must be clearly identified and addressed during project planning phases. Appropriate Quality Assurance (QA) and Quality Control (QC) focus must be placed on identified high-risk areas. In order to be effective, quality systems must be flexible, non-confrontational, consistent, and adaptable to projects of any size ? from capital mega-projects to small maintenance projects. All project participants must be aligned in how they are approaching quality and the difference between QA and QC must be clear to everyone on the project. Emphasis must be placed on QA activities to minimize project cost, reduce rework, manage change, and reduce the production facility operational risk. QA is focused on the work processes used to generate the design and confirming that the processes are present and being followed. Issues in the work processes guarantee that the output drawings and specifications will be less than optimal. The identification and monitoring of quality-critical processes provides a focus for QA activities. QC activities are then used to generate proof that the project was implemented correctly and become a key part of the turnover.

Nov 1, 2011

By R. A. Guereca

The Bureau of Mines conducted an analysis to determine criteria for steady-state, laminar flow boundary conditions for a coiled-tube gas viscosimeter by comparing experimental data from a thick-walled, stainless steel capillary in a horizontal, straight-tube condition, with similar data taken after the same capillary was formed into a helix. Overlapping volumetric f10wrates and pressure drops are covered for both configurations at pressure levels of 28, 225, and 1,000 psia at 3000 K. Friction factor, Reynolds number, and Dean number correlation plots show conditions where the coi1ed-tube flow deviates from straight-tube flow. The coiled-tube data indicate departure from Poiseui11e steady-state laminar flow at a Reynolds number close to 390 and a Dean number of about 15. Below these conditions and consistent with the data reported, Dean's circulation appears negligible. For the particular coil used, a conservative upper limit of 10 is chosen for the Dean number corresponding to an upper limit of about 250 for the Reynolds number.

Jan 1, 1967

By R. Graeme, J. Komadina

Gold Fields acquired an option to purchase the Cerro Corona Project, located in Hualgayoc, Cajamarca Department, Perú, in December 2003. In January 2006, the option was taken up and the transaction closed. During the intervening months, Project development occurred against the backdrop of a Presidential election, increasing national social activism and environmental regulation, rapidly escalating operating and capital costs, as well as unprecedented demand for engineering and technical skills. Project “Lessons Learned” are outlined and discussed in the context of an evolving strategy.

Jan 1, 2007