Search Documents

A series of laboratory based push and pull tests were carried out to investigate how surface profile influence the load transfer mechanism of bolt/resin interface. Tests were carried out in both 75 mm and 150 mm long steel sleeves. Three types of bolts were examined, they were bolts most commonly used for strata reinforcements in underground coal mines in Australia. The bolts had near equal core diameter but of different profile configurations. The change in the length of the encapsulation sleeve was examined in light of the small number of profiles encapsulated effectively in short 75 mm long sleeves. The results showed that peak loads and displacements were directly related to the height and the spacing of the bolt surface profiles. Profile spacing appears to have greater influence on load transfer capacity than the profile height.

Jan 1, 2006

By Jianliang Li, Jan M. Mutmansky

This study analyzed laboratory comminution techniques for respirable mine dust generation and the properties of the resulting dusts. It was the objective of the study to determine the suitability of the resulting dusts in reflecting the properties of natural airborne dust. This paper deals specifically with the amount of contamination introduced into the generated dust as a result of abrasion when using nine different grinding methods. The analysis was made by comparing the content of 25 chemical elements in the lab-generated dusts with the same elements in the airborne coal mine dusts. It was found that all the lab-generated dusts possessed contamination but that several methods produced smaller percentages of contamination and that the residence time in the grinding device was an important factor in the contamination levels.

Jan 1, 1992

By G. W. Gross

A commercial deposit of white kaolinite clay contained in the sandy overburden of the Cambrian Gatesburg formation in Central Pennsylvania was successfully mapped by combined SP and resistivity methods and results were checked by drilling. Resistivity minima in the range between roughly 2000 and 3500 ohm-meters coupled with second-order SP maxima of 50-60 mV contrast were found to characterize commercial white kaolinite clay beneath not more than 30-40 ft. of sandy overburden in the area stdied. This investigation supports the hypothesis, established previously, that certain SP phenomena may reasonably be ascribed to diffusion and membrane potentials produced by interaction of clay lenses, sandy matrix, and ground waters. The success of this test proves that this prospecting technique can assist in locating clay deposits in sandy overburden derived from the weathering of sandstones and carbonate rocks such as the Cambrian formations of Central Pennsylvania. In a recent paper, Gross and Moore (1959) described broad self-potential minima above the outcrops of the Cambrian Gatesburg formation. These "first-order" SP anomalies, of 220-350 mV contrast (Figure 7), are related to the peculiar sandy residual soil covering the Gatesburg formation. Small positive ("second-order") peaks of 50-60 mV contrast are superposed on the bottom or flanks of the first-order troughs. They appear to be related to lenses and layers of kaolinite clays within the sandy Gatesburg overburden. Both first-order and second-order anomalies show a characteristic inverse relationship with apparent resistivity profiles in most cases. An explanation in terns of liquid-junction and shale potentials was advanced. According to this working hypothesis, shale potentials are generated: 1) at the contact of the sandy Gatesburg overburden with the more argillaceous soils of surrounding formations; 2) at the boundary of clay lenses contained in the sandy matrix of that overburden. Concentration gradients between interstitial infiltration waters and perched water tables within the Gatesburg overburden are believed to give rise to the liquid-junction potentials. In order to test this hypothesis further, a detailed study was carried out of a second-order positive anomaly on the property of the Woodbury Clay Co. at Mines (Blair County, Pa., Hollidaysburg folio of the U.S. Geological Survey). A second aim was to establish if combined SP and resistivity surveys are suitable as a practical method for delimiting favorable areas in which commercial kaolinite clay de~osits may be found by drilling. Drilling control was provided by the Woodbury Clay Co. PROCEDURES Instrumentation used for SP measurements was the same as described in the paper mentioned. For resistivity surveys, a direct-current voltmeter-ammeter device built by Georator Gorp. of Manassas (Va.) was used in combination with non-polarizing electrodes from the same manufacturer. Power was supplied by one to six 45-volt, heavy-duty B-batteries

Jan 1, 1961

By P. E. Donaldson

Since 1992, Falconbridge has made available to the international copper industry, Kidd Creek's licensed refinery process technology under the name of the Kidd Process. This has resulted in the supply and installation of permanent cathodes and associated product handling equipment to refineries in Canada, the United States, South Korea, Chile and Mexico. These installations accommodate both electrorefining and electrowinning processes. The growth and industrial acceptance of the Kidd Process has generated technical advancements in the areas of product random sampling, corrugation, marking, labeling, product tracking and data acquisition. In a different area, the expanded development of custom materials processing at Kidd created a need to advance technologically. The process-related problem of high nickel concentrations in refinery electrolyte compromised an increase in current density to >300 A/m2. The need for nickel removal resulted in Kidd Creek's newly developed Nickel Recovery System. The effective and economical extraction of nickel, along with reduced antimony and bismuth levels, reduces bleed stream volumes and/or neutralization costs and simultaneously produces a marketable nickel carbonate product.

Jan 1, 1999

By Y. P. Chugh, R. F. Roethe

Surface coal mining productivity in the US and Illinois has declined since 1969. The US Department of Energy conducted an analysis in 1980 of the causes of declining productivity in different states. This paper presents a detailed analysis of changes in overall productivity and productivity in different functions, such as overburden preparation and stripping, reclamation, and coal handling, from 1970 to 1982. Statisical analysis techniques, including multiple regression were used in the study.

Jan 1, 1985

In the 100 years since the formation of The Australasian Institute of Mining and Metallurgy there have been significant changes in all aspects of the mining industry.A number of the changes have been driven by technical evolution or necessity, others have been driven by developments in the application of the products produced from the mining of minerals. Other changes have been driven by shifts in community values.

Jan 1, 1993

By David Browne

THE use of coal-dust fired reverberatory furnaces, or indeed of reverberatory furnaces of any description, was for the Canadian Copper Co. a matter of necessity, and not of choice. For 20 years smelting had been done in blast furnaces alone, and with the Herreshoff furnaces used prior to 1904 there was no trouble in treating fine ores. But little flue dust was produced, and this, following the time-honored custom, was wetted down and put back with the charge. Whether the flue dust really smelted, or whether it was worn out by being chased around in a circle, was a problem that troubled no one. With the installation of modern blast furnaces and high-pressure blowing engines, in 1904, flue dust commenced to assert itself. Evidently more dust was made than could be smelted, but so many vital problems engaged our attention at that time that this minor question was pushed to one side. In 1906, the details of blast-furnace smelting and the conversion of matte had been worked out to a satisfactory conclusion, and the ever-increasing piles of flue dust and fine ore on the stock yard demanded serious consideration. Numerous experiments in sintering, briquetting, mixing with converter slag, forming blocks of flue dust with green-ore fines and cement, and so on, were undertaken. None of these showed much promise. Our problem, was still further complicated by the question of treating converter slag. The ore was basic, the slag was not needed as a furnace flux, and it was felt that under these conditions the old method of pouring slag in molds and resmelting in the blast furnace was an unnecessary expense. If the converter slag could be settled in basic-lined reverberatory furnaces, in which at the same time flue dust and green-ore fines could be smelted, two problems might thus be solved.

Jan 1, 1915

By R. Sharma

The heterogeneous distributions of nodule sizes, cover-ages and abundances and the variability of their burial und association with sediments and rock outcrops on the seafloor have emerged as crucial parameters in considering the exploitation potential of the manganese nodules in the central part of the Indian Ocean. Nodules with the long axis measuring from 20 and 40 mm (0.8 and 1.6 in.) account for nearly 60% to 70% of those evaluated from photographic and grab-sample data. In addition, 75% of the nodules (by weight) are between 20 and 60 mm (0.8 to 2.4 in.). The distribution of nodules with abundances ranging from 1 to 20 kg/m2 as well as coverages of 1 % to 90% on the seafloor are important considerations in demarcating the potential areas for nodule mining. The mining of areas with higher concentrations of nodules, such as along slopes associated with less sediment, would result in the enhanced recovery of nodules compared to areas with low nodule concentrations, such as in valleys and plains where thick sediment covers occur. The mining head will encounter substrates such as hard rock exposures, either with or without Fe-Mn encrustations, as well as soft sediment layers in the nodule fields. It must be able to collect buried nodules under sediment cover, and it must be able to negotiate uphill and downhill slopes in mining areas. Mapping prior to mining must delineate areas to he avoided and must define locations to be mined. The requirements suggest that the nodule collector must be a dynamic (active) system with sensors to detect areas of potential nodule concentrations, as well as features that are hazardous (or unfavorable) for mining operations.

Jan 1, 1999

By F. C. Gregory

"Introduction.The third annual mine-rescue maneuvers of the Globe-Miami District First Aid and Mine Rescue Association were held at Globe, Ariz., on November 5 and 6, 1923. The first demonstration was held in October 1922, and the results** from that experiment, both in the practical training and the interest aroused in the apparatus men, were so much more satisfactory than those from the ordinary smoke-chamber training, that Orr Woodburn, director of the Association, decided to hold similar maneuvers at frequent intervals. The second test was held on March 21-22, 1923, in connection with the meeting of the Southwest Mining Section of the National Safety Council at Globe.Place and Organization.The recent maneuvers were held in the same mine and conducted in the same general manner as the first, and the points of interest not brought out previously are described below. By studying the accompanying map the movement of the teams can be better understood.Thirty-three apparatus men were out on the first day and thirty-two on the second day, a total of forty-three men being trained.Mr. Woodburn was aided in directing the work by his two assistants from the mine-rescue station, two local safety engineers, and an engineer from the Bureau of Mines. Local mine superintendents and the State deputy mine inspector were interested spectators."

Jan 1, 1924

By R. Walker, R. J. Anslow

Today at Tampa we see the end results of a team effort: A vital link in an intermodal transportation system, the link that enables the unit-train concept to be employed with full effectiveness and the link that improves the economics of water transportation systems. Two new phosphate transfer complexes with a multi- million ton annual capacity are in operation in Tampa, Fla. Revolutionary in concept, these companion installations represent a total investment in the Tampa Bay area of $18.5 million.

Jan 1, 1970

By C. B. Mapes, E. C. Dowling Jr.

"To reduce concentrate dewatering and drying costs, the Concentrator Division at Phelps Dodge Morenci, Inc. investigated available filtration technologies. Numerous methods were explored, including: drum, disk, belt, pressure, hyperbaric, and ceramic media filtration. An economic evaluation of the individual filtration technologies indicated the advantages of ceramic media filtration for Morenci concentrates. This paper discusses the technological development culminating in the first full scale application of ceramic media disk filters in North America. Low moisture contents are obtained at high production rates and greatly reduced operating costs.INTRODUCTIONPhelps Dodge commissioned the Morenci Concentrator Filter Plant in 1942 with four 8'6"" Dorr-Oliver cloth disk filters. That year, the filter plant processed 265,537 tons of concentrate grading 20.5% Cu. The filter cake production averaged 9.3% moisture. In 1944, the Extension Filter Plant commenced operation with three additional 8'6"" Dorr-Oliver cloth disk filters. This coincided with the expansion of the concentrator. Production that year totaled 451,567 tons of concentrate grading 23.8% Cu. Moisture averaged 9.4%.Through the years additional filter units have been added in response to increased concentrate production. An Eimco drum filter was installed on the extension side and an additional Dorr-Oliver disk filter was installed on the original side in the 1950's. In 1961, two 8'6"" Peterson disk filters were installed, one on each side to replace two worn-out DorrOlivers. The installation of four 10xl2 foot Peterson drum filters was completed in 1974, coinciding with the Metcalf Concentrator startup. An Eimco belt filter was installed later.The greatest change to concentrate dewatering at Morenci occurred in 1963 with the addition of a 10x60 foot rotary gas fired dryer. The installation also included a number of conveyors to deliver filter cake from both plants to and from the dryers. Other ancillary systems included dust scrubbers and their slurry pumps. The commencement of drying was undertaken due to the rapid increase in cake moisture as a result of the LPF process and the recycling of acid plant scrubber dust slurry from the smelter. In 1972, a second dryer system was installed to increase capacity."

Jan 1, 1993

By Thomas R. Kuesel

In traditional construction contracting practice, the owner allocated almost all risks to the contractor, saying in effect, "you deal with all construction problems and all third parties, and don't bother me." In this same tradition, the architect or engineer designed a structure in its finished condition, and if he thought about the construction problems that might be involved in building it, he was careful not to express any opinions on these matters in the contract documents. This feudal attitude fostered two results: 1. Contractors added high contingencies to their bids to cover the costs of risks. 2. Litigation of construction contract claims blossomed. Broadly, the owners lost--the courts reallocated many risks the owners thought they had laid on the contractor. Thoughtful owners and engineers recognized that owners were paying for risks twice --once in bid contingencies and a second time in court. Meanwhile, contractors were not getting rich; they were losing money on delays and disputes, and just about getting even (if they were lucky) in court. And construction law was becoming an increasingly lucrative field--for lawyers. Furthermore, with the growing influx of lawyers onto the construction scene, the owner-contractor-engineer relationship became increasingly an adversary one. The emphasis came to be on culpability rather than capability--who could be held responsible for breaching some contract clause, not who might find a solution to some common problem. This game was played with equal vigor by owners and contractors.

Jan 1, 1979

By A. S. Mallicis, Li Xiawoei, P. W. Weiblen, I. Iwasakl

Platinum group metals (PGM) are often found in close association with arsenide and sulfarsenide minerals in copper-nickel bearing gabbroic rocks. Major losses of platinum in flotation have been attributed to the susceptibilities of the arsenic minerals to oxidation and subsequent losses of their recoveries in cleaner flotation stages. The use of a nitrogen atmosphere in grinding and in flotation, the effectiveness of activation for improving their floatabilities, and the role that electrochemical interactions play not only between grinding media and minerals, but also among different minerals, are discussed.

Jan 1, 1989

By Lo YC, Pate WT

In recent years there has been a great deal of interest in ways to optimise the performance of mineral processing plants. This paper describes a methodology developed for optimisation of autogenous and semiautogenous mills. The methodology involves plant sampling, batch testing, modelling, computer simulation, control strategy evaluation and implementation. The models have been tested in plant operations to verify the research findings and predictions. Two example applications of this approach to plant optimisation are presented. Benefits reported in these two examples are in the range of four - eight per cent increase in size reduction efficiency.

Jan 1, 1993

En quoi consistent les études de suivi des effets sur l?environnement (ESEE)? Les ESEE constituent une méthode de suivi scientifique que l?on peut employer pour déterminer la santé des écosystèmes aquatiques (qui peuvent être touchés par l?activité humaine) et l?efficacité des mesures de protection de l?environnement. Les ESEE sont des évaluations scientifiques itératives du poisson, de l?habitat du poisson et des ressources halieutiques. Le programme comporte des phases séquentielles de deux à six ans de suivi, d?interprétation et de compte rendu au cours desquelles la fréquence et le type de suivi dépendent des résultats des études précédentes. Le programme des ESEE pour les mines de métaux est fondé sur un accord conclu à l?unanimité entre les intervenants. Les exigences du programme et les guides techniques connexes ont été élaborés à la suite d?une consultation multilatérale à laquelle ont participé les représentants du secteur privé, du gouvernement et des collectivités. Toutes les mines assujetties au Règlement sur les effluents des mines de métaux (REMM), aux termes de la Loi sur les pê ches, doivent procéder à une ESEE dans le cadre de l?autorisation qu?ils ont reç ue de rejeter des effluents. Le REMM a été enregistré le 6 juin 2002 et publié dans la Partie II de la Gazette du Canada le 19 juin 2002 (SOR/DORS/2002-222).

Nov 1, 2002

By R. Hummel

In the quest to reduce overall costs and improve operating efficiency, the application of GPS based technology in open pit mining has evolved significantly in recent times. Venetia Mine has been leading the way in the De Beers group in the implementation of these systems and the realization of significant benefits from them. Following on from the successful results and the notable benefits obtained from the Wenco Truck Dispatching system and the Caterpillar CAES system on the loading and dozing equipment, Venetia has implemented the first fully functional and integrated GPS based drill monitoring system in southern Africa to its drilling operations. This paper elaborates on the concept of drill monitoring and how the vision for the application of the system at Venetia has developed and been implemented. The paper further describes the workflow involved, beginning with the initial test work done with SSI Kaltex and the Australian Drill Advisor system through to the final details of the integration of the Aquila system with the CATERPILLAR Computer Aided Earthmoving System (CAES) and the alliance with SandvikRock Tools. Most importantly, the paper details the benefits that are derived from drill monitoring and the use of the information generated by such a system. Venetia has pioneered the move towards smart partnerships and alliances with strategic suppliers within the De Beers group. The area of drilling, as the important start of the entire mining process, has been no exception and the final part of the paper covers how drill monitoring provides vitally important information that enables a supply partnership, to function cost-effectively and profitably for both parties involved. By having the type of accuracy, detail, validity and timeousness in the information being received as a result of the implementation of such a system, better management decisions can betaken, creating a more focused and efficient mining environment. In these times of increasing costs and reduced commodity prices, the mining industry will be required to continue pushing the boundaries on these technology applications in order to remain competitive.

Sep 1, 2001

By F. R. Conley, D. A. Shock

Solution Mining or In Situ Mining has received increasing attention in the past few years because the method offers many attractive possibilities in improving the environmental impact of mining as well as making feasible the extraction of deeper, low value mineral reserves. This paper will present a brief discussion of the state-of- the-art in total solution, slurry removal and leach mining. As a specific example of utilizing the method, the uranium deposits of South Texas are a type of deposit which have been considered as being amenable to in situ leach mining. The parameters required to ascertain the amenability of such a deposit for in situ leaching will be presented. The hydrological factors which influence the production of the soluble uranium solutions and their displacement will be discussed. Mathematical models for various well configurations have been made and graphic representation will be presented to illustrate various production methods and the resultant hydrological consequences.

Jan 1, 1974

By W. H. Jay

Sulphide-containing minerals, particularly iron, lead to acid formation. In turn, the acid generates effluents such as copper acid drainage (AMD). The Berkeley Pit in Butte, Montana, USA and Mt Lyell in Tasmania, Australia, represent just two of many sites throughout the world for which acceptable treatment methods are required. In the gold cyanidation process, the presence of copper creates both a significant cost impediment and a potential environmental hazard. The tailings dam failure at Baia Mare in Romania which led to the release of copper and zinc cyanides created a major environmental disaster. The application of non-toxic water soluble polymers and ion exchange resins to selectively recover copper from AMD solutions, and the in-plant treatment of copper cyanide solutions and slurries to recover copper and recycle cyanide to prevent cyanide entering the tailings impoundment will be discussed. The economics of the various processes will be highlighted.

Jan 1, 2003

By Prakash AJ, Singh PK, Dhar BB

Safety and stability of underground mine openings, coal pillars and water dams in the near vicinity of operating surface mines are endangered from excessive blast induced vibrations. This paper deals with the investigations carried out in four coal mines. Simultaneous measurements at equal distances from the source indicated higher level of vibration on the surface than those produced in the underground workings. The values of peak particle velocity (PPV) measured on coal pillars, body of water dam were lower than those measured on roof and junctions of the roadways. The parting of coal (3-4.5 m) between two sections vibrated with higher PPV compared to the roof of top section and floor of bottom section. In one case the influence of total charge fired in a round was significant in generation of vibration compared to the maximum charge/delay where monitoring was done vertically below the source.

Jan 1, 1995

By John F. Barkley, J. W. Woomer, H. F. Yancey, H. B. Charmbury

The coal picture in 1955 was much brighter than in 1954, when the tonnage produced dropped to the 1939 level. Bituminous coal and lignite production are expected to approach 465 million tons, against 392 million tons in 1954, an increase of about 19 pct. On the other hand, the production of anthracite declined about 7 pct to some 25 million tons. There was marked improvement in coal consumption in all industrial lines except railroads. At the end of November 1955 the largest consumer, electric power utilities, had used about 126 million tons, an increase of some 22 million tons over the previous year. Coke-oven consumption increased about 19 million tons and coal coked in beehive ovens increased about 1.5 million tons, due to heavy coke

Feb 1, 1956