Search Documents

By Byron N. Cooper

The Revenue Act of 1926 provided for five simple categories of natural resources to have the benefit of depletion allowances. In the 1947 Revenue Act, the number was increased to twenty-five, and in the 1951 Revenue Act to fifty-four. Of this number, fourteen were allowed 5 per cent; nine, 10 per cent; twenty-nine, 15 per cent; one, 23 per cent; and one (oil and gas), 27.5 per cent. The 1951 Revenue Act created a host of difficulties, including application of the "end- use criterion" and determination of the commonly accepted meaning of such terms as limestone, dolomite, chemical- and metallurgical-grade limestone, marble, calcium carbonates, and magnesium carbonates. Dolomite, for example, was listed at 10 per cent depletion allowance, but without definition. In the great amount of litigation growing out of the 1951 Revenue Act and its administration, it became essential to understand the derivation and subsequent usage of these common geologic terms. One thing that became clear was that our definitions changed significantly between the time that the 1951 Revenue Act became law and the time that later cases were tried. Some geologists neglected to learn about first usages of such terms as metallurgical limestone, and about meanings that were applicable when the 1951 Revenue Act was written and passed. Legal meanings in this paper are discussed in the light of certain famous cases that have been tried and settled.

Jan 1, 1966

By W. L. Cornell, F. W. Benn

The U.S. Bureau of Mines investigated froth flotation techniques to remove heavy metals (Pb, Cu, and Zn) from southeast Missouri lead mill tailings. It has been estimated that southeast Missouri contains between 200 and 300 million st of Pb tailings stored above ground. The tailings were classified as two distinct types: (1) pre- 1968 tailings from the Old Lead Belt (some more than 100 years old) and (2) post-1968 tailings from the New Lead Belt. The objectives of the investigation were to reduce the Pb remaining in the tailings to (500 ppm (<0.05% Pb) and to attempt to recover a marketable concentrate to offset a portion of the remediation costs. The remaining dolomite-limestone would then be used as mining backfill or agricultural limestone. Bench- scale froth flotation removed, in percent, 95 Pb, 84 Cu, and 54 Zn, leaving 94% of the original weight containing, in parts per million, 400 Pb, 40 Cu, and 300 Zn from the Old Lead Belt tailings. Separate flotation tests also removed, in percent, 85 Pb, 84 Cu, and 80 Zn, leaving 75% of the original weight containing, in parts per million, 400 Pb, 200 Cu, and 500 Zn from the New Lead Belt tailings . Concentrates recovered from the Old Lead Belt were retreated to produce a final Pb concentrate containing 72% Pb with a cleaner flotation recovery of 79%. Froth flotation proved to be a viable method to remove the heavy metals.

Jan 1, 1992

Develop new technology to encourage domestic processing of automobile catalytic converters for recovering platinum -group metals. Background Automobile catalytic converters are used to convert pollutants in automobile exhaust into water vapor, carbon dioxide, and nitrogen, About 1 million troy ounces of platinum-group metals arc used each year in the. United Slates to manufacture catalytic converters. It has been estimated that about 60 pct of the used catalytic converters arc being collected. Most of these used catalytic converters were not processed in the United States but were exported to Japan or Europe for processing. In 1991, about 250,000 troy ounces of platinum-group metals were recovered from scrap catalytic converters collected in the United States. Each short ton of decanned catalyst may contain 30 troy ounces of platinum-group metals valued at over $15,000. Development of an economic process for the recovery of platinum-group metals that can be operated on a small or large scale may increase, the percentage of catalytic converters collected and encourage domestic processing to recover a platinum-group metal concentrate. This would significantly decrease the dependence of the United States on imports for these critical and strategic metals.

Jan 1, 1992

By Williams RJ

This paper presents an overview of the design and development , application to date and potential of a real-time return gas monitoring system.Initially developed as an ACARP/Industry funded project, whose prime aim was to create a `turn-key&apos;, prototype, stand alone, real-time, Return Gas Monitoring System (RGMS) capable of providing quantitative assessments of gassiness levels on a shift by shift basis, enabling unusual gas emission patterns to be readily flagged.

Jan 1, 1998

By Quan Situ

In evaluating the influence of increased mine ventilation utilizing the vertical production shaft as intake or exhaust, various factors, such as conveyance motion and especially the shaft guide system, have been studied. Case studies of two typical conveyance guide systems, namely rope guide (in a potash mine) and fixed guide (in a hard rock mine) are presented.

Oct 21, 2015

By C. A. Pickles, K. Mackowiak

Black Thor chromite ore from the Ring of Fire deposit in Northern Ontario was carbothermically reduced in a microwave system to produce a ferrochromium alloy. The as-received ore contained 43.0% Cr2O3, 19.9% Fe2O3, 14.5% MgO, 13.4% Al2O3, and 7.0% SiO2. Activated charcoal was utilized as the reducing agent. Firstly, TGA/DTA and permittivity studies were carried out in order to determine the relationship between the reduction process and the microwave susceptibility. Secondly, microwave reduction experiments were performed on the chromite ore. The variables investigated were; the amount of carbon, processing time, input power and type of atmosphere. A maximum chromium grade of 76.1% and a chromium metallization of 82.7% were obtained for a processing time of 20 minutes, a power input of 800 W, and a carbon addition of 15% in an argon atmosphere.

Jan 1, 2017

By W.G. Harbert, C. Upthegrove

DURing the past year considerable work dealing with physical properties of cartridge brass was done at the University of Michigan in cooperation with the Ordnance Department of the U. S. Army. This paper gives some of the data bearing on the effect of the anneal, previous to the final reduction-or rolling, on the physical properties, particularly the hardness. Various phases of the subject of physical properties of cartridge brass have been presented by different investigators. Mathewson and Phillips1 refer to the work of Grard, in 1909, as the first systematic presentation of the relation between temperature and time of anneal, changing of physical properties and microstructure, and the previous reduction by cold rolling. They discuss the relation between time and temperature of annealand the previous reduction by cold rolling; also the relation between physical properties and grain size of annealed brass. The degree of deformation previous to the annealing was found to determine the temperature at which recrystallization and corresponding changes in physical Properties would take place. relation between grain size and Brinell hardness, found the hardness for low-temperature annealing to be dependent on the previous degree of reduction, while for anneals above a certain temperature the hardness after the anneal was independent of the degree of reduction. Actual differences in hardness, due to the degree of reduction, disappear only on annealing at 600" C. or above; though the differences for metal subjected to different degrees of reduction and annealed at temperatures between 350" and 600" C. were found to be relatively small. In their determination of the relationship of grain size to Brinell hardness, Bassett

Jan 1, 1923

By W. G. Harbert, C. Upthegrove

DURing the past year considerable work dealing with physical properties of cartridge brass was done at the University of Michigan in cooperation with the Ordnance Department of the U. S. Army. This paper gives some of the data bearing on the effect of the anneal, previous to the final reduction-or rolling, on the physical properties, particularly the hardness. Various phases of the subject of physical properties of cartridge brass have been presented by different investigators. Mathewson and Phillips1 refer to the work of Grard, in 1909, as the first systematic presentation of the relation between temperature and time of anneal, changing of physical properties and microstructure, and the previous reduction by cold rolling. They discuss the relation between time and temperature of annealand the previous reduction by cold rolling; also the relation between physical properties and grain size of annealed brass. The degree of deformation previous to the annealing was found to determine the temperature at which recrystallization and corresponding changes in physical Properties would take place. relation between grain size and Brinell hardness, found the hardness for low-temperature annealing to be dependent on the previous degree of reduction, while for anneals above a certain temperature the hardness after the anneal was independent of the degree of reduction. Actual differences in hardness, due to the degree of reduction, disappear only on annealing at 600" C. or above; though the differences for metal subjected to different degrees of reduction and annealed at temperatures between 350" and 600" C. were found to be relatively small. In their determination of the relationship of grain size to Brinell hardness, Bassett

Jan 1, 1923

The past year has been a difficult one for the mining industry in this country, but an active and successful one for the Branch. Membership has continued to increase, albeit at a slower rate than last year, and with the increase almost all from student membership. I dwelt at some length last year on the continued increase in student membership, which I ascribed largely to deliberate policies adopted by the Branch to foster this area of membership. I don&apos;t propose to reiterate these, suffice it to say that as usual, the Otago School of Mines has been a prolific source of student members, and it will be a pity if this source dries up û more on this subject later. In fact, students form just on 29 per cent of the Branch&apos;s total membership û a far higher percentage than for any other Branch in the Institute, whose membership as a whole comprises only ten per cent students.

Jan 1, 1985

By R. W. O. Kersten, J. D. Austin

A questionnaire was circulated in 1986 that had the objective of establishing the type of material that members would like to see featured in the Journal of The South African Institute of Mining and Metallurgy. The questionnaire contained five main questions involving the following:

Jan 1, 1987

Drainage aids are designed to assist in filter cake dewatering by reduction of surface tension. By the early 1980&apos;s severalspecialist chemical manufacturers had developed drainage aids specific to the alumina industry. Thus, after some initial laboratory work, drainage aid addition to the product hydrate filter cake was first tried at Gove in early 1981. Encouraging results led to further plant trials and a laboratory trial comparing eight different products. Fromthis last trial a product was chosen and a plant trial run in March 1982. The results achieved encouraged a further plant trial to be run during April and May, 1982 and a decision was then made to adopt the full-time use of drainage aid on the plant.Optimisation work with the drum filters and drainage aid continued until late 1983. This work not only led to optimisation of dose rates, concentrations etc., but also to significant improvements in the mode of operation of the product filtration area.

Jan 1, 1985

By N. S. Dalal, Xianglin Shi

Metal ions, such as chromium (Cr) and vanadium (V) are found as trace impurities in mineral dust. Since metal ion mediated free radical generation has been implicated in many disease processes, we carried out a detailed investigation of the metabolism of these metal ions by biological redox systems and the possible oxygenated radical generation therefrom. We found that highly reactive Cr(5+) species are generated in the reduction of Cr(6+) by NADPH-dependent glutathione reductase, lipoyl dehydrogenase, and ferredoxin-NADP+ oxidoreductase. The reduced metal ion species react with hydrogen peroxide, to generate hydroxyl (•OH) radicals in a continuous cycle. The enzymatic catalysis processes also involves the reduction of molecular oxygen to the superoxide [(0-1 2)] radical. Thus only a trace amount of metal ions chemisorbed on mineral dusts, such as quartz, can catalyze the generation of the highly toxic oxygenated radical species from cellular hydrogen peroxide, suggesting a new biochemical mechanism for mineral dust induced chronic lung injury.

Jan 1, 1991

By W. Setzepfandt, J. Henneke

PREFACE Debris disposal can very often be a severe problem and major restriction on tunnel boring projects, especially for small diameter tunnels and in underground mines. Hydraulic transport could provide a suitable solution. Investigations have therefore been made in connection with a full-scale project of 4.8 km length and 2,3 m diameter, to obtain the required technical and economical data for planning an optimized transport system, e.g. for a tunnel boring drivage of 6 - 7 m diameter in underground coal mines. INTRODUCTION The Radau-Tunnel, chosen for the investigations, has been designed for transferring flood peaks between the rivers Radau and Grosse Romke in the Harz-Mountain of Lower Saxony. A DEMAG TVM 20/23 H tunnel boring machine was used to drive the tunnel on a rising gradient of 0,53 %. The rock consisted of shale and hornblende (55 %), granite (15 %), diabase (15 %), chert (8 %) and gabbro (7 %). The project has been sponsored by the Federal Ministry of Research and Technology.

Jan 1, 1981

By Nicholas Kyriazi, John P. Shubilla

A joint effort by the U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR&apos;s), deployed in accordance with Federal regulations (30 CFR 75.1714), survived the underground environment with regard to both impact damage and aging. This report presents findings regarding laboratory-tested SCSR&apos;s from 1982 through 1990. The SCSR&apos;s were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except for units with manufacturing defects or design deficiencies. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. This poses a potential danger to a user in an emergency. Recommendations include improved training in inspection procedures.

Jan 1, 1992

By Wm. Mark Hart

Under a specific geological condition, roof supporting method, and pillar-entry system, an entry convergence concept may be the most effective means that can be used to effectively indicate the longwall entry stability (i.e. pillar bumps, roof falls, or floor beaver This concept may also be used to verify the effectiveness of the current pillar-entry system and roof supporting method. Furthermore, convergence measured under different mining phases may lead to a better understanding of the longwall mining-induced abutment loads and may be used to estimate stress change in pillars and thus pillar stability. In this paper, a remote entry activity monitoring system was designed; a comprehensive entry convergence monitoring strategy was proposed; thee abutment loading phases in longwall mining were defined; the relationship between roof deflection and stress change in a pillar was derived, and finally the extent and magnitude of the mining-induced abutment loads as well as their impact on entry convergence were discussed using the field data obtained so far.

Jan 1, 1995

Virginia Polytechnic Institute, Department of Mining Engineering, Blacksburg, Va Otto C Burkhart, Professor of Mining. The titles of pertinent publications have been abstracted from the Bulletins on Research and Publication This material has also appeared, in most cases, under other auspices Presumably, the Bulletins whose titles are quoted may be had for the cost of postage The coals of Virginia (1927), Ceramic resources of Virginia and their development (1929), Effect of ilhum crucibles on volatile determinations of coal (1930), Possibility of briquetting southwest Virginia coals (1930), Coking of semi-anthracite coal of Virginia (in preparation), Distribution of ash in the Merrimac coal seam (1929); Unit coal studies on some Virginia coals (1931), Sulphur forms in Virginia coals (1931); Comparison of results of fusion point of coal ash obtained by two different methods

Jan 1, 1933

By Joseph Cervik, Fred Garcia

Gob holes are routinely used by the mining industry to vent methane from gobs and to prevent it from entering the mine ventilation system. In some cases, flows from gob holes are measured by centering an anemometer on the end of the discharge pipe. These measurements are erroneous and tend to be high by as much as 30%. The Bureau of Mines determined correction factors (method factors) for anemometer measurements taken in this manner. Method factors for 10.2, 15.2, and 20.3 cm (4, 6, and 8 in) ID pipe are 0.68, 0.71, and 0.78, respectively. Comparisons between horizontal and vertical flows indicated no significant change in method factors. Consequently, the method factors for horizontal pipe flows can be applied to vertical upward flows.

Jan 1, 1987

By A. M. Gow

THE trend in ball milling has been toward mills of larger diameter, but without fundamental laws as a guide. The speeds at which mills are run have been a matter of cut-and-try. This paper deals with both diameter and speed and proposes to show the laws which apply to some laboratory ball mills, ranging in diameter from 18 to 42 in., run at various speeds. The correlation of power, speed, and grinding rate of the respective mills will be shown by curves of markedly significant similarity. Before presenting the results some consideration will be given to the mechanics of ball milling.

Jan 1, 1930

By W. C. Hazen, A. V. Henrickson

URANIUM plant operations of the Kerr-McGee Oil Industries at Shiprock, N. M., began in December 1954. As originally designed, the plant treated Plateau carnotite ores by the acid cure process, which dissolved both uranium and vanadium minerals. After 16 hr of acid curing, the ore was conveyed to an agitator and leached for 2 hr in acid liquor at a pH of 1.0. The leach pulp was then separated at 100 mesh in a classifier, the sands continuing through a washing classifier circuit and the slimes going to a countercurrent decantation system of four thickeners.

Jan 9, 1957

By C. Morrow

Deformation studies were performed on tuffaceous rocks fran Yucca Mountain, Nevada Test Site to determine the strengths and coefficients of friction under confining pressures from 10-50 MPa at room temperature. Frictional strengths of 30ºsawcut samples increased with pressure and reached values of around 150 MPa at the higher confining pressures. However, the failure strengths of the intact samples were quite unpredictable. The coefficients of friction ranged between 0.7 and 0.9 for all specimens. These data can be used in conjunction with in situ stress measurements at Yucca Mountain, to evaluate the potential for earthquake activity in the region.

Jan 1, 1984