Search Documents

By T. Takahashi, K. Oyamada, Y. Miyata, T. Isoo

The carbonation reaction of steelmaking slag has been known for many years. However, the size of blocks manufactured from this by-product material has been limited due to the difficulty of achieving a uniform reaction throughout the block. Using newly developed conditions, large porous slag blocks (1.0 x 1.0 x 0.5 m) were produced by car¬bonation of steelmaking slag with the optimum amount of water and supplying CO2 deep into slag powder compacted in molds. The development of these blocks has great poten-tial to solve the problem of slag utilization, for example, by recycling slag in large car¬bonated blocks for artificial fish reefs and seaweed cultivation beds. This paper de¬scribes the carbonation reaction, the new process for producing large slag blocks, and the utilization of blocks in past and recent years.

Jan 1, 2004

By Fengxiang He, T. Meadowcroft, Yanjun Zhang

Slag from the zinc fuming furnaces contains about 3 percent zinc and 0.1 percent lead. The paper outlines several experimental techniques for recovering these components from liquid fumer slag. The simplest method, remelting followed by a hold period, indicated that a substantial fraction of the metal values was recoverable as a result of fuming into the gas phase, presumable by reduction of the metal ions by divalent iron ions. Following on from this, slag samples were equilibrated with copper, chosen because the activity coefficients of zinc and lead in copper are very low. This improved metal recovery, with substantial amounts of lead and zinc reporting to the liquid copper as well as to the fume. Application of an electrical emf across the slag-metal interface, using a graphite anode and a liquid copper cathode, resulted in further gains in metal recovery.

Jan 1, 2004

By T. Ko, K. N. Han, C. S. Park, N. S. Kim, C. Yoon, H. Yoon

Quantitative analysis of Platinum Group Metals from ore samples and industrial materials using Inductively Coupled Plasma-Mass Spectrometer (ICP-MS), Inductively Coupled Plasma-Atomic Emission Spectrometer (ICP-AES), Atomic Absorption Spectrometer(AAS), and X-ray Fluorescence (XRF) techniques was conducted and the performance of various techniques was compared. The effects of different matrices in the sample materials were compared and discussed for each analytical technique. The ICP-AES technique exhibited better accuracy than AAS but showed limitations in its application due to strong spectral interference in the presence of common matrix elements such as iron. The ICP-MS showed the lowest detection limit and less spectral interferences than the previous two techniques. The XRF technique was also applied to examine the total amount of PGM from industrial materials. Results from each analytical method on various sources were presented and discussed.

Jan 1, 2003

By John Birkinbine

In the preparation of the paper upon " The Operation of Warwick Furnace, Pennsylvania, from August 27, 1880, to September 1,1885," presented at the Pittsburgh meeting, I purposely refrained from offering theories to explain the peculiarities of furnace operation, on the ground that it was better for those actively engaged in blast-furnace management to present records of operations, than for one more directly interested in blast-furnace engineering and construction to venture upon the sea of speculation as to causes. The manager of an iron-works naturally feels that he knows as much about his particular furnace or furnaces as any one else, and as Mr. Cook, after his close attention to and study of the Warwick furnace, was at that time unwilling to present theories, I felt a disinclination to assume more acumen than the manager.

Jan 1, 1887

By W. E. Lamont

The Bureau of Mines conducted flotation tests on a mixture of barite waste materials from Nevada in which essentially all of the barite values were finer than 20 micrometers. Flotation variables investigated in these tests were the effects of (1) sodium silicate as a pulp dispersant, (2) sodium hydroxide as a pH modifier, (3) increased amounts of sodium cetyl sulfate, (4) conditioning time and (5) solids content during conditioning. The optimum flotation conditions were achieved by adding 2.5 pounds of sodium silicate and 10 pounds of sodium cetyl sulfate per ton of feed and conditioning the pulp for 20 minutes at a 35-percent solids content. Using these conditions, a concentrate was produced that contained 94.7 percent BaS04, with an attendant recovery of 90.9 percent of the barite in the feed. In addition to the flotation tests, a selective barite flocculation process was developed to treat extremely fine barite. A barite concentrate containing 96.5 percent BaS04 with an attendant recovery of 82.1 percent of the barite was produced by selective flocculation. A process patent application has been filed based on this process.

Jan 1, 1982

By R. E. Peterson

The Bureau of Mines has undertaken beneficiation investigations on samples representing large tonnages of oxidized taconites in order to develop and evaluate applicable technologies for producing iron oxide concentrates from these materials. Information derived from the investigations can be used to expand the domestic iron raw-materials base and to establish the impact these taconite deposits may have on future national iron ore requirements. This report describes a process that includes reduction roasting, magnetic separation, and flotation, applied to a western Mesabi Range sample taken near Coleraine, Minn. The sample contained 36.8 pct iron and 46.0 pct silica, and represented 0.5 to 1 billion tons of crude material. An average of 962 lb/hr of oxidized taconite was roasted with 33 lb/hr of lignite in a 35-foot-long rotary kiln. Pulverized lignite and natural gas maintained the kiln operating temperature at 850° C. The roasted taconite was beneficiated by magnetic separation and cationic flotation in a 900-lb/hr pilot plant and yielded a product analyzing 68.1 pct iron and 4.6 pct silica, and containing 82.4 pct of the iron in the kiln feed.

Jan 1, 1981

By F. H. Gibson

In recent years physico-chemical techniques have been applied for rapid analysis of coal and coke ash as replacements for classical wet-chemical methods. Although the classical methods are accurate, they are time consuming because many chemical separations are necessary to complete an analysis, and they require skilled analysts for accurate work (12).4 For the past several years the Bureau of Mines has applied some of the newer physico-chemical techniques in its continued search for new and improved methods at analysis. The methods of analyzing coal and coke ash evolved from this work include spectrophotometric methods far SiO2, A120, , Fe203 , TiO2, and P2O5; chelatometric titration for CaO and MgO; and flame photometry for Na20 and K2O. The methods are rapid and direct, are suitable for analyzing a group of samples at the same time in production work, and dire results with almost the same accuracy as classical procedures. With the new methods, complete analyses in duplicate can be obtained at a rate of 2 to 3 times that of conventional methods.

Jan 1, 1962

Application of Agitated Leaching for Iron Removal from Silica Using Sulfuric and Hydrochloric Acid In this research, iron removal from silica used in glass industry was investigated using agitated leaching method. Silica sample was provided from silica concentrate originating from Chalchoog Silica Mine located in Abhar, Iran. The sample contained silica, iron oxides and clay minerals. For characterization of samples XRD and XRF analysis and atomic absorption method were applied. Silica and iron oxide (Fe2O3) grade of head sample was 98.41 per cent and 0.067 per cent respectively. Two inorganic acids (sulfuric and hydrochloric acid) were used in agitated leaching tests. Two series of L9 orthogonal array of Taguchi design with replication were used to determine the effect of parameters including acid dosage, leaching duration, ambient temperature and solid content on iron removal. The statistical calculations and analysis of variance (ANOVA) were carried out by means of DX7.0, Minitab14.0 and Winrobust1.02 softwares and also statistical calculations were checked manually using Excel software. Also multivariate regression was applied in order to forecast Fe2O3 conent of final product. The optimum conditions for leaching tests which sulfuric acid was employed are as follows: 40 minutes leaching time, temperature of 85¦C, 40 g/L acid concentration and solid content of 20 per cent. Under this condition the amount of iron oxide in silica was decreased to 0.042 per cent. The optimum conditions for leaching tests which hydrochloric acid was employed are as follows: 80 minutes leaching time, temperature of 75¦C, 30 g/L acid concentration and solid content of 20 per cent. Under this condition the amount of iron oxide in silica was decreased to 0.035 per cent.

Sep 13, 2010

By S. -H. Sohn, M. -K. Cho, G. -G. Hong

In order to evaluate the properties of coating materials for BOF, the effects of dolomites (dolomite and light burned dolomite) addition on durability of coating materials were investigated. In all coating materials, matrix was dicalcium ferrite(C2F) and both free MgO and dicalcium silicate(C2S) were precipitated. Fe203 content must be controlled to improve the adhesion and durability of coating materials for BOF during oxygen blowing process. The amount of dolomites added to BOF slag must be controlled in optimum condition with high refractoriness of C2S to improve the adhesion of coating materials for BOF. The weight ratio of converter slag to dolomite must be below 8 to improve the adhesion and durability of coating materials simultaneously.

Jan 1, 2004

By Michel Grenier, David A. Young, Brent Rubeli, Mahe Gangal

This work forms part of a study being conducted into the feasibility of constructing a prototype Load Haul Dump (LHD) vehicle for operation in underground Canadian mines. A series of in-laboratory assessments were performed to determine the relative contributions of a Deutz F4L912W (54 HP- conventional vehicle engine) and a Deutz F2L 2011 (31 HP hybrid vehicle engine) to diesel emissions concentration during mine transient duty cycles and steady-state operating modes respectively. Results indicate significant reductions in the quantity of gaseous and particulate emissions with the application of the hybrid system and a high-efficiency ceramic element filter. This paper describes the engine test protocols and the results of this laboratory study.

Jan 1, 2006

By J. Murphy

The economics of microbial coal desulfurization are affected significantly by the proper selection of the plant site and by maintenance of variables at suitable levels. High sulfur coal particles below 200 mesh show sulfate production rates triple those with 150 mesh coal but grinding costs are greater. Slurry solids density increases from 5% to 20% reduced the rate constant by a factor of 10. Coal added to a batch reactor in the stationary phase resulted in a sudden second exponential sulfate production phase indicating feasibility of lower cost continuous operation. Successful operation in the absence of beef broth, yeast or added nutrients at non-sterile conditions enhanced projected economics. Finally, the need for adequate agitation and aeration was well established.

Jan 1, 1985

By F. S. McNicholas

IN the first big blast at Climax, a "loop back" (three-wire system) was used (Fig. 1), with the idea of securing a wiring system that would give to all series the same amount of current. Single-phase, 60-cycle, 13,800-volt FIG. 1.-Loop BACK. A THREE-WIRE SYSTEM WITH BRANCHES VARYING IN LENGTH. power was furnished to the blasting transformers, each of which has a rated capacity of 600 amp. at 480 volts. Two blasting leads were taken from these transformers, giving a blasting current of single phase, 60 cycle, 480 volts, with an instantaneous capacity of more than 600 amp. The blasting switch was on the secondary leads from the transformers, to avoid lag in energizing them.

Jan 1, 1938

By Alan Campoli

The Eclipse System was developed by Minova USA Inc. formerly Fosroc Inc. to improve the performance of 5/8-inch deformed rebar fully grouted into a one inch borehole. An 1/8-inch offset bolt head combined with specially formulated Eclipse Lokset resin cartridge results in reduced gloving and increased mixing efficiency. The benefits of the Eclipse System have been demonstrated, under the supervision of MSHA, in Kentucky, West Virginia and Illinois coal mines in partnership with Excel Mining Systems, a leading roof bolt manufacturer. Over 100,000 units have been installed to date. Eclipse system bolts exposed during overcast construction at the Panther Mine of Cumberland Resources displayed an extremely well mixed, uniform resin anchorage over the entire bolt length.

Jan 1, 2003

By Prohaska G, Jackson F, Jack B

To learn more about the fundamental roof behaviour in South African coal mines, accurate underground measurements of roof deflection were conducted in bord and pillar panels during development and pillar extraction. To conduct these measurements a survey levelling technique was adapted. The overall system reading accuracy was established as being within 0,4 mm on a 15 m sighting distance. The underground sites were modelled and, for a roadway development, similar symmetrical curvatures were calculated by a linear elastic model, as were measured underground. In a pillar extraction panel, a significant amount of bed separation was measured and the roof underwent an a-symmetric movement due to the close presence of the mined out area at one side of the roadway.

Jan 1, 1992

By J. Hudy

The performance of six dense-medium washers was evaluated in five preparation plants. Three of the plants were making a two-product separation that produced a clean coal and a refuse; one plant employed dense-medium vessels in series to effect a primary and a secondary separation; and one plant was equipped with a two-compartment washer effecting two separations in one vessel. The separate secondary drum-type washer produced a low-ash metallurgical coal and an intermediate-ash product suitable for plant fuel or steam generation. The two-compartment washer produced a premium anthracite product and a middlings product. The sharpness-of-separation values ranged from good to excellent for the five primary separations and for the secondary separation.

Jan 1, 1968

AT A MEETING of the Shareholders of the Russo-Asiatic Cons. Ltd., in London, Oct. 23, 1922, LESLIE URQUHART, chairman of the com- pany made the following statement:* I come now to our recent negotiations with the Soviet Government and to the agreement which has resulted from them. You will remember that the conference at The Hague broke up without having achieved anything very definite. It was not, however, a failure. It elicited from M. Litvinoff an offer which will, I think, come to be regarded as a milestone in the progress of Russia from a ruinous and unpracticable Communism towards a modified form of capitalism. The offer made by M. Litvinoff at The Hague amounted in effect to this: that in return for political recognition on our part the Soviet Government would first acknowl-edge its liability for Russia's national foreign debts, and, secondly, would give the original foreign owners of property in Russia effective compensation. A very great advance that. It showed-and there have been many other signs to confirm it-how real and persistent has been the internal evolution of Russia during the past year from Marxism to the economics of the Western world. I will not now detain you with the reasons why M. Litvinoff's highly promising and significant offer came to nothing. The fact that it had been made and the further fact that The Hague Conference had separated indefinitely were the important things. The first fact seemed to indicate that the Soviet rulers, after all, proved to be people with whom one could do business. The second fact rather emphatically showed that the way to do business with them was not by unwieldy poly-glot conferences of ministers, officials and experts representing a few dozen different governments and a few dozen different sets of national interests. That method had been tried at Genoa. It was tried again at The Hague. Each time it failed, and having failed it left the road clear for a simpler and more direct approach.

Jan 12, 1922

By V. Rajaram

The oil shales located in the Appalachian Basin cover an eight-state area of the eastern US and are referred to as Devonian (black) shales. These shales have been exploited for their gas potential for several years. The Institute of Gas Technology (IGT) has conducted research since 1972 on the production of shale oil from the Devonian shales. This resulted in the development of the HYTORT process. This process demonstrated that the yield from the Eastern oil shales can be greater than the value indicated by the Fischer assay method. IGT estimates that 67 Gm3 (423 billion bbl) of oil could be recovered by HYTORT processing of surface minable eastern US shales. Recently, American Syncrude Corp. and Southern Pacific Petroleum NL have proposed oil shale projects in Kentucky. This paper will describe the surface mining and retorting techniques that have been studied for exploitation of the Devonian shales, and enumerate the problems that have to be overcome before commercial production can be realized.

Jan 1, 1986

By N. S. Tanious

This paper summarizes results from an investigation into possibly the largest coal pillar failure in the USA. The newly opened coal mine worked an 3.35 m (11 ft) seam under overburden depth that ranged from 91 to 671m (300 to 2200 ft) . The mine main entries, and the enclosed pillars, experienced a massive slow squeeze. The squeeze could not be controlled and the mains were lost. A new set of mains were driven. Entry convergence (closure) measurements were carried out behind the advancing face to monitor stability. Pillar stresses were also measured under four different depths of overburden: 229.433, 472.579 m (750,1420,1550, and 1900 ft). The strength of pillars in the new mains was calculated from the loads that triggered the failure in the old mains, using three pillar strength formulas. The stress measurements showed that the new pillars supported more load than their predicted strength, indicating that current strength formulas are inadequate under deep conditions.

Jan 1, 1992

By Nancy S. Raymon

The Bureau of Mines investigated the effect of controlled additions of selected metal oxides, as well as the adjustment of the calcia-to-silica ratio on the high-temperature strength of refractory-grade periclase. Increases in the hot flexural strength of some periclase materials in the range of threefold to fourfold were obtained with additions of Zr02 and by adjustment of the CaO:Si02 ratio to the 2.5 to 3.0 level. Results show that for each periclase refractory raw material, there exists a combination of level of Zr02 addition and an adjustment to the CaO:Si02 ratio that optimizes the hot flexural strength of each of these materials. Data also indicate that the improved hot strengths can be attributed to the high-temperature secondary phases formed between the different levels of periclase impurities and the additives, resulting in improved intergranular high-temperature bond strength.

Jan 1, 1982

The Prince Lyell Mine has been the major production source at Mount Lyell since under-ground mining commenced in 1972.Three lifts of stopes have been mined to date, with the fourth, the 40 Series lift, to commence production this year. As the mine has progressed deeper, the ore haulage system has evolved to accommodate the mine's economic circumstances while maximizing efficiency.In the first, or 10 Series lift of stopes, ore was removed from drawpoints by L.H.D. units and tipped directly into rakes of 7 tonne rail cars. The original concept for deeper stoping lifts entailed L.H.D.'s tipping into long ore passes, rail haulage, underground crushing and hoisting to surface via the No. 1 Shaft. The suspension of the No. 1 Shaft project in 1976, due to economic difficulties, lead to the intro-duction of diesel truck haulage of ore, initially via the internal Prince Lyell Decline and now to surface via the Main Decline.

Jan 1, 1985