Search Documents

By Gadd D. E

Since October 1972, New Zealand Steel Mining Ltd has loaded around 10 million tonnes of ironsand concentrate from single-point mooring buoys located off-shore at Taharoa on the west coast of the North Island of New Zealand. Before the first off-shore loading system was installed a considerable research effort was applied to proving the slurry loading technique. Subsequently the system has been expanded and a new buoy, pipelines and pumping system were installed in early 1978. Since then 110,000 DWT class ore carriers have been loaded at rates of around 2600 tonnes per hour through twin submarine pipelines. This paper reviews the operation of the shiploading system and attempts to answer the question: "If the Taharoa operation were to be planned in 1980, would the same research spending be necessary or have published research results since, made such practical tests unnecessary?".

Jan 1, 1980

By R. Karl Zipf

In some instances, extensive room-and-pillar working scan collapse with little warning and pose a serious risk to underground miners. Traditional strength-based pillar design methods applicable to coal or hard-rock mines use a factor of safety defined as pillar strength divided by pillar stress. Factor of stability, defined as local mine stiffness divided by post-failure pillar stiffness, may offer a way to design room-and-pillar mines and eliminate collapses. Three alternative design approaches to decreasing the risk of large-scale catastrophic collapses are described: the containment approach, the prevention approach, and the full-extraction approach. Until good data on the post-failure behavior of pillars become available, the containment and full-extraction options are the safest. The limitations in our ability to evaluate both the stability of old workings and the long-term performance of room-and-pillar mines are described.

By Hempenstall J, English W

Mine management has a responsibility under the various acts of state parliaments for the adequate ventilation of existing workings. It also has a need to plan adequately for the ventilation of proposed workings. Future workings alternatives have become progressively more complex and ventilation planning of the various possibilities must be undertaken within an atmosphere of rapidly changing market circumstances, etc. Any non-optimal solution will prove more expensive than necessary on both capital and cost bases. Clearly these increasing and alternative ventilation demands of coal mines in Australia have multiplied the work load of ventilation engineers. Management in general has for some time been aware of the advantages of using computers for commercial applications such as payroll and stores inventory. However, while the hand held calculator has replaced the traditional log tables and slide rules for smaller engineering calculations, the larger digital computer has not made the same

Jan 1, 1983

By W. R. Webster

Opinions still differ widely concerning the requirements, chemical and physical, which should be expressed in specifications for steel rails, in order to secure results satisfactory to both manufacturers and purchasers.

Jan 1, 1902

By M. Radwan

This research reports on the synthesis of advanced silicon-based structural ceramics from mixtures composed of natural sand (Sinai white sand), reclaimed silicon and graphite by the nitriding combustion synthesis method. With pulverized sand (? 40 m), we found that the nitriding combustion can be realized at self-sustaining mode in the SiO2?Si?C system under 3 MPa nitrogen pressure. Depending on the composition of the starting mixtures, single-phase silicon oxynitride (Si2N2O) powder as well as new Si3N4?Si2N2O and Si2N2O?SiC composite powders with controllable chemical compositions were successfully developed. The measured thermograms of various combusted mixtures and the thermodynamic characteristics of possible exothermic reactions in this system were discussed to explain the nitriding combustion behaviour and mechanism. Near-full dense Si2N2O were fabricated from synthesized Si2N2O powder with 5 wt % oxide additive by the spark plasma sintering (SPS) method at 1600 °C. The dense Si2N2O samples had good mechanical properties (18.7 GPa Vickers hardness, 3.3 MPa m1/2 fracture toughness and 363 MPa strength) and excellent chemical and oxidation resistance. The synthesized composite powders were also densified to high densities (> 90 % of theoretical values) by SPS technique. The results obtained in this study can be seen as a new route to prepare important silicon-based structural ceramic powders with various compositions/properties from cheap starting materials which makes them potential for wide range of applications.

Jan 1, 2006

By J. J. Moore, I. Iwasaki, L. A. Lindeke

Correlation of scale-up from small-scale batch laboratory mills to large-diameter industrial mills was established by performing two series of laboratory and pilot plant grinding tests using a magnetic taconite ore and a siliceous sulfide ore. In one series, controlled batch grinding tests in 203-, 508-, and 914-mm (8-, 20-, and 36-in.) diameter mills were carried out followed by a second series involving continuous grinding tests using 305-mm (12-in.) and then 1067-mm (42-in.) diameter pilot plant ball mills in open circuits. The effects of ball diameter on wear and of mill diameter on grinding power and ball wear are illustrated.

Jan 1, 1988

By L. M. English

A basic model was developed to help assess methane control needs for the longwall mining of coal in gassy areas. Rather than depending on reservoir and rock mechanical theories, it uses an empirically determined gas emission rate as an input, and it operates on the assumption that, within a specific region and zone, gas emissions will be relatively equivalent for uniform incremental volumes of gob created by mining. The computer program divides longwall panels into segments, keeps track of the face advance and generates emission rates and volumes for both the entire panel and for individual zones within the panel by summing values for all undermined segments. This model can aid in the determina¬tion of the number, size and location of vertical wells or other methane-control applications that are needed for gob gas control.

Jan 1, 2000

By F. M. Doyle, Jun Li, Milton E. Wadsworth, E. Peters

The Raman spectroscopic technique was used to study electrochernically oxidized pyrite in-situ. It was found that Raman-active sulfur oxidation products could be detected after a proper potential was applied to the pyrite electrode for a threshold period of time. There existed a minimum potential below which sulfur could not be observed. However, when the applied potential exceeded a certain limit, the intensity of the sulfur spectra decreased. The minimum potential at which sulfur could be observed changed with solution pH. For both acid (pH 2.7) and weak alkaline (pH 9.2) solutions, the minimum potential was 0.8 V/SCE, whereas for neutral (pH 6.5) solutions the value was 0.4 V/SCE. In strong alkaline solutions (pH 12.5) surface sulfur oxidation products could not be detected at any potential.

Jan 1, 1993

By J. E. Dooley

An analytical procedure developed by the Bureau of Mines was applied to the separation and characterization of a 370° to 535° C distillate from Swan Hills (south field), Alberta, Canada, crude oil. Investigators determined the general characteristics of the crude oil by the Bureau's routine method for crude oil analysis. Suitable fractions were prepared for instrumental analyses by utilizing such techniques as isothermal and molecular distillations, chemical treatment, silica-alumina gel chromatography, and gel permeation chromatography (GK). A detailed characterization of the 370° to 535° C distillate was possible by the application of GPC-mass spectrometry correlations and nuclear magnetic resonance spectrometry. Semiquantitative data based on mass Z series distributions were determined and are shown. The data will be valuable in developing future processing techniques and in calculating yields for converting high-boiling distillates into more useful energy forms.

Jan 1, 1973

By J. P. Baur

The sensitivity of radiochemical techniques makes possible the study of the initial-stage sulfuric acid leaching kinetics of chalcopyrite and other copper sulfide minerals. This Bureau of Mines study of the initial leaching of chalcopyrite used techniques to evaluate the molecular and electrochemical processes. High-grade Transvaal chalcopyrite was neutron-irradiated in a TRIGA reactor4 to produce radioisotopes copper-64, iron-59, and sulfur-35. Dissolution rates were measured in the time interval zero to 60 minutes, during which time significant anomalies were observed. First was an initial period of rapid dissolution lasting a few minutes; second, an arrest or ?plateau? region usually lasting from 6 to 10 minutes; third, a second period of dissolution of lesser rate than the first. The effects of solution variables such as pH, oxygen partial pressure, and ferric ion concentration at different temperatures were measured.

Jan 1, 1974

By C. E. Lawall

WHEN this study was started very little information was available, regarding the physical characteristics of West Virginia coals. This was particularly true of friability and of crushing strengths of the coals. Some work had been done on specific gravity studies but the available information applied to only a few coals. In practically all coal-classification systems thus far proposed, the predominating factors of classifications are largely based on the chemical characteristics of the coal. Recently some investigators have pointed out that a classification based on chemical and physical properties of coal might serve to place coals in their proper group better than classification systems based on chemical properties alone. One of the aims of this study was to obtain some data on the physical properties of coal which might help to properly classify West Virginia coals.

Jan 1, 1932

By Maria I. De Rosa

Table 10 and figure 4 show the number of fires and fire injuries occurring at the surface of underground coal mines by state during 199&1999. Table 10 also shows by state the risk rate, employees' working hours, and lost workdays. A total of 65 fires occurred in 10 states. Thirteen of those fires caused 12 injuries and 1 fatality (the yearly average was 6.5 fires and 1.2 injuries). Four fues and one fire injury involved con- tractors. The Ewhr value was 97 x l O6 hr (Irr = 0.025); the LWD value was 6,206. Pennsylvania had the most fues (20 fues and 5 injuries), followed by West Virginia (1 6 fires and 1 fatality) and Kentucky (1 5 fires and 3 injuries). Among these states, Pennsylvania had the highest injury risk rate value (Irr - 0.095). Table 1 1, partly illustrated in figure 5, shows by time period the number of fires, fire injuries, and fire fatalities; risk rates; employees' working hours; and lost workdays. The number of fires and fire injuries show a decrease followed by an increase during the five time periods, accompanied by a decline in employees' working hours throughout the periods (see table 11 and figure 5). The Irr values follow patterns similar to those shown by the injury values. Tables 12- 17 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 6 shows the major variables during 199&1999. Table 18 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

This paper discusses why Argyle Diamonds adopted thickened tailings disposal in 1985 and how the system was developed over the next seven years. A wide ranging review of the thickened tailings disposal system and the tailings deposit it was producing was carried out during 1992 and 1993. The results of that review led to the abandonment of thickened tailings disposal at Argyle because of serious concerns about the stability of the resultant tailings deposit. The exposure to the risk of liquefaction and an assessment of the consequences if this happened to the thickened tailings deposit are shown. The criteria for selecting the new tailings disposal strategy are then described. The final section of the paper discusses the management strategies that have been put in place. These are designed to: ò reduce the risk posed by the thickened tailings deposit to an acceptable level; ò safely store tailings to the end of mine life; ò produce a land form that can be decommissioned to the satisfaction of Government regulatory bodies.

Jan 1, 1996

By Karen L. Menna

At Digital Equipment Corporation, increasing demands on executive secretaries to share, track, and retrieve information prompted development of ALL-IN-1 System for Executive Services. Executive secretaries asked engineers to combine word processing and electronic mail with utilities for managing time; logging and tracking telephone calls, letters, and inquires; creating presentations; compiling directories; and archiving. The system, two years in development, now automates the president's and senior vice presidents? offices at Digital. It allows secretaries to interrupt any task with two keystrokes, and return later to the original task. The system has speeded customer response, enabled online information sharing, and increased professionalism and customer satisfaction.

Jan 1, 1989

By JoAnn Silverstein, Eric A. Marchand

Competition between Thiobacillus ferrooxidans and non-iron-oxidizing heterotrophic bacteria was induced by the addition of glucose to a co-culture of T. ferrooxidans and A. acidophilum in an oxygen-limited environment. Iron oxidation was inhibited as dissolved oxygen was used preferentially for glucose metabolism. Furthermore, as the water became anoxic, glucose was consumed along with the oxidized iron species (Fe3+) during iron respiration resulting in a pH increase from 2.0 to 4.0. Results suggest that biologically mediated acidification of drainage water can be reversed by dispersion of an easy to degrade, soluble, and inexpensive carbon source such as glucose into the subsurface.

Jan 1, 2000

By Leif A. Nordell, Philip E. Freeland

A paper discussing specification, methods, situations and results encountered in underground phase construction of the Rocky Mountain Pumped Storage Project near Rome, Georgia. The scope of work included excavation, rockbolt/shotcrete/wire mesh primary support and cast-in-place concrete lining of the (1) 216 m, top flared shaft, connecting 1.57 radian elbow, and 590 m tunnel to a 10.67 m finished diameter; (2) complex double bifurcation section; (3) excavation, support, installation and backfill concrete for three parallel, 135 m steel penstocks of 5.79 m finished diameter; (4) construction of a 43 m diameter reinforced concrete intake/discharge structure atop the shaft.

Jan 1, 1985

By Robert J. Morris, John N. Butler

A series of organic collectors has been developed which successfully float synthetic secondary uranium minerals, such as autunite, carnotite, and torbernite. Recoveries up to 97 pct have been obtained. With cleaning of rougher concentrates, ratios of concentration as high as 15:l are possible on head assays of 0.10 to 0.50 pct U308. Additions of certain base metal salts aid in recovery and materially in- crease the rate of flotation and selectivity of the collectors for the synthetic minerals. Flotation tests on natural uranium minerals have not yet equaled results obtained on the synthetics, although these collectors do give better results than conventional collectors for nonsulfide minerals.

Oct 1, 1956

By J. E. Lawver, W. D. Carrier

During the past 20 years, millions of dollars in research effort have been spent to improve methods of phosphate clay dewatering and disposal. Although to date no proven large-scale system has been developed that will result in ultimate below ground storage without the use of at least temporary dams, considerable progress has been made and a variety of techniques are being tested, some on a large scale. This paper summarizes the use of mathematical and centrifuge (physical) models that can analyze and evaluate various systems for the consolidation of phosphatic clays. These provide a powerful tool for engineers responsible for land management and mining waste disposal.

Jan 1, 1985

By Richard H. Sprute, Dennis J. Kelsh

Slow-settling, fine-grained suspensions can often be dewatered and densified by applying direct current between buried electrodes. Although water removal rates and power expenditures depend on physical and chemical properties of the treated slurries, metal mine tailings from Idaho, Colorado, and Mexico have responded well in laboratory testing, as have 29 samples of ultrafine coal waste from mines in nine states. This Bureau of Mines report reviews field tests at two Idaho metal mines and describes the recent installation at the Henderson molybdenum mine near Empire, Colorado, and the treatment of coal sludge at a Clinchfield Coal Co. preparation plant near Dante, Virginia.

Jan 1, 1980

By Craig R. Smith, Warren Pfefferle

Tests were conducted utilizing large flat jack devices placed in a vertical slot for high pressure loading of rock to measure in-situ properties of a rock mass. The high pressure flat jack devices were used as a site investigation tool to obtain rock mass properties. Tests were conducted before and after a 100 ton surface high explosive detonation test to assess explosive effects on the rock. It was conclusively demonstrated by these tests that meaningful flat jack tests could be successfully accomplished; also, a significantly different response of the rock medium was measured as larger areas of rock were loaded. Surface jointing was severely disturbed by the explosion.

Jan 1, 1971