Search Documents

To produce industrial-grade titanium castings by processes that are nonpolluting and lower cost than the currently used rammed-graphite process. Approach Foundry-grade zircon and olivine sands, bonded by waterglass or bentonite, are used to make shell or rammed molds which require relatively low-drying temperatures and do not generate noxious fumes during drying or casting. Procedures Three separate processes have been developed which meet the stated pollution and cost goals. These are: 1. Waterglass-bonded rammed zircon or olivine sand molds are dried at 480°F, zirconia washed, redried, and used in an inductoslag or skull-casting furnace. 2. Waterglass-bonded zircon or olivine sand shell molds are formed at 560°F, cured at 620°F, zirconia washed, dried at 480°F. and used in an inductoslag furnace. 3. Rammed zircon and olivine sand molds are bonded with western bentonite, zirconia washed, dried at 980°F, and used in an inductoslag or skull-casting furnace.

Jan 1, 1981

By P. Hickey, A. Oliver

"In March 1993, Ram Raising Limited was faced with a challenge. Placer Dome Incorporated, Dome Mine Division requested from Ram Raising that they design station excavation into the existing No. 8 shaft from No. 3 mine levels. This work had to be done without loss of production time in the underground department.Due to the time frame of the project, every detail had to be carefully considered, with extra care that all pros and cons had been worked out.Ram Raising submitted a work Plan that had been worked out with the Redpath Group which included the infrastructure requirements; the engineering design; the scheduling and sequence of work; and the excavation design and blasting procedures.A proposal was' put together by both Ram Raising and Placer Dome outlining the infrastructure requirements, including the engineering design, scheduling and sequence of the work, excavation design and blasting procedures. The proposal accepted by Placer Dome and, on July 3D, 1993 work commenced to breakthrough eight stations. Work continued until December 1993 with the completion off our stations. The project was then stopped to allow the station access drifts from No.3 mine to be completed. The second phase of the project began on May 27 and was completed on September 15, 1994.This paper shows how, through innovative design and the full cooperation between client and contractor, a project of this nature can be completed successfully."

Jan 1, 1995

By W. K. Brisden

The SAG Milling Seminar, which was held at Murdoch University in Perth on 30th November and 1st December, 1989, was a very successful technical seminar. Organizer Dr Norm Stockton reported a total attendance of 130, which was higher than the 70 expected: 20 delegates came from the eastern States and the remainder were from Western Australia.

Jan 1, 1990

A review of the motivation of personnel in the open cut mining industry. The effect of social, geographic, environ- mental, organisational, union and other factors on employees' motivation as assessed from job experience and from an attitude survey. An appraisal of where we should be heading and what influence management can have on the motivation of employees.

Jan 1, 1980

By Ed H. Wipf, Kurt L. Bryan, O&apos

Flow sheets employing SAG Mills as the initial stage of grinding are commonly selected for comminution of ores. Several alternative technologies are available. The paper will provide a brief review of the latest alternatives to SAG mills. Included in this review will be a discussion of the comparable benefits of each technology. Commonly accepted disadvantages will also be presented.

Jan 1, 1998

By D E. Siskind

The Bureau of Mines performed a comparative study of nine sites at eight surface coal mines to determine if the presence of near-surfaced underground abandoned workings resulted in the generation of adverse long-duration, low-frequency blast vibrations. Six of the nine sites had underlying workings, and two had thick layers of low-velocity unconsolidated surface material.

Jan 1, 1990

By H. D. Dahl, P. C. Thakur

This paper presents an analysis of a new tool for improved productivity in coal mining: the horizontal drilling system developed by Conoco/Consol. The analysis includes a brief description of the system; discussion of the three categories of advance exploration application of horizontal boreholes; and a survey of other special mining methods planned around long horizontal boreholes.

Jan 1, 1983

By Lars Osen

Both fragmentation and safety can be improved by following proper procedures in loading boreholes. Proper loading procedures such as primer location, borehole sealing, decking, and stemming along with the hazards of dropping on primers are presented. Discussions follow on the reason for the use of each procedure along with the possible consequences such as hazards, misfires, or poor fragmentation.

Jan 1, 1985

In Mount Isa voltage and frequency fluctuations caused. by haulage shaft operation gave considerable difficulties with the initial application of Atomic Absorption Spectro-photometry.The methods used to stabilise the various units ' have been described.- Some other difficulties and the means used to eliminate or reduce them together with a-modified burner design are also discussed.

Jan 1, 1963

By Walter Valery, Sergio Vicuna, Roberto Valle, Hamer Arevalo, Ben Burger, Lui Vargas, Alex Jankovic, Jim Seidel, Eduardo Nozawa

This paper describes the design, the first three years of operation and optimization of a large, single stage SAG mill at Minera Yanacocha’s Gold Mill facility located in northern Peru. The Gold Mill was commissioned in March 2008 with a 32’ x 32’ EGL, 16.5MW single stage SAG mill, to process 5 million tonnes per annum high grade oxide Au/Ag ore. Operational control, feed size distribution, grinding media, mill liner, grate and pulp lifter optimisation have allowed the mill to operate 15-30% above design throughput rates, but with a product P80 coarser than design. As part of the optimization, full grinding circuit surveys were conducted. Historical operating data and survey data were analyzed and used to evaluate possible circuit changes and determine alternative operating strategies. A number of changes were implemented which allowed the SAG mill to operate similarly to a large ball mill and achieve finer mill product that was closer to design. This paper summarizes life to date data analysis and improvements made by Minera Yanacocha as well as the grinding circuit optimisation study conducted by Metso Process Technology and Innovation.

Jan 1, 2012

By K. F. Hollberg, D. Graehl, L. Despain

OCI Wyoming's recent expansion of its surface Soda Ash production facilities outstripped the mine's ability to supply Trona ore necessitating infrastructure changes to the mine. A computer simulation of the mine's production systems along with the surface facilities was created to determine the most economic investment alternatives to increase mine production. This paper describes the development of the simulation model; the results obtained, and discusses the issues involved in using simulation modeling for mine production system design.

Jan 1, 2002

By Gungor Tuncer, Ali Kahriman

"In bench blast design, not only the technical and economical aspects, such as block size, uniformityand cost, but also the elimination of environmental problems resulting from ground vibration and airblast should be taken into consideration."

Jan 1, 1999

At CPA we believe that ore bodies discovered in future will be bigger and higher grade than the ones currently known and set out targets accordingly. Discoveries over the last three decades substantiated this approach.

Jan 1, 1987

By Major William R. King U. S. Engineer

My attention was drawn to this subject just twenty years ago this month, when I was detailed to rebuild one of the bridges in Richmond that had been burned during the evacuation. We took pos

Jan 1, 1886

Preliminary plans of this meeting, together with a most interesting series of papers that have been received or promised, were published in the May Bulletin. The plans are being carried out enthusiastically and hospitably by the Colorado members and all indications point to an interesting and valuable meeting.

Jan 6, 1918

By D O. Tan Sky

This paper will describe the mechanisms involved in delay blasting and how they are applied with the use of D.S.B. It will examine the control of potential damage resulting from detonations, and show how good fragmentation and efficient recovery of this material blasted can be achieved.

Jan 1, 1980

By F. M. Doyle, Jun Li, Milton E. Wadsworth, Ximeng Zhu, E. Peters

The electrochemical behavior of pyrite in borate/sulfate solutions was investigated using cyclic voltammetry. Three anodic peaks at approximately -0.8 V, -0.1 V and +0.5 V (SCE) were detected along with their corresponding reduction peaks. The first two peaks correspond to the oxidation of surface products. The third peak corresponds to the direct oxidation of pyrite with reaction products FeO oxides. sulfate ion and partially oxidized sulfur intermediates present as a surface film of polysulfides and So. The Few oxides and sulfur intermediates were reduced to ferrous hydroxide and HS during the negative-going scan. The HS interacted preferentially with Fe(OH), on the surface to form FeS. Excess fenous hydroxide continued to reduce to metallic iron. During the return positive-going scan, metallic iron was oxidized to ferrous hydroxide and FeS was oxidized to pyrite. These reactions are characterized by a unique double peak observed in the region -0.8 to -0.65 V. The growth kinetics of the surface sulfur film formed during anodic oxidation were studied using chronoarnperomeay. Potentiostatic measurements were well correlated by a paralinear rate equation, suggesting the formation of an intermediate passive film, associated with the simultaneous dissolution of the outer layer of the film. The reaction rates were affected by applied potential, solution pH and temperature, but were independent of electrode rotation speed. A reaction kinetics model which fitted well with experimental results, was developed.

Jan 1, 1993

At its meeting on February 21, 1933, the Board of Directors passed the following resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters: WHEREAS, the Board of Directors at its last meeting passed the following resolution: "The Board of Directors, having been appealed to by several Local Sections for advice concerning the attitude and policy of the Institute relating to the endorsement of candidates for public office, the following statement of

Jan 1, 1938

By Joe Strobbe, Kevin Joe

The U.S. Bureau of Reclamation awarded PCL Civil Constructors the project to build a new visitor's center and parking lot structure at the Hoover Dam. The excavations for these structures present many blast design challenges. The visitor center, a 30 foot deep excavation was blasted in the Nevada side of the canyon wall, 600 feet above the existing power plant. This excavation also included a through-cut underneath the existing road that carries the traffic over the Dam between Nevada and Arizona.

Jan 1, 1993

Arkansas Geological Survey, Rooms 443-447 State Capitol, Little Rock, Ark George C Branner, State Geologist A list of available publications will be sent upon request Publications issued by the U. S Bureau of Mines, U S Geological Survey and Oklahoma Geological Survey, pertaining to' Arkansas, are also available through this Survey office. Annual Reports may be had for the following years. 1890, 3147, 1891, 81 35; 1892, $1 10 Other available publications: The slates of Arkansas, by A H. Purdue, with a bibliography of the geology of Arkansas by John C Branner (1909), $1.10, Coal mining in Arkansas, pt 1, by A A Steel (1910), 3175, An outline of the physical features of Arkansas, by George C Branner (1927), free, An outline of the metallic minerals of Arkansas, by George C Branner, free, Bulletin 3, The geology of the Arkansas Paleozoic Area, by Carey Croneis (1930), $3 20, Bulletin 4, St Peter and older Ordovician sandstones of northern Arkansas, by A W Giles (1930), $1 95, Bulletin 5, A geomagnetic survey of the bauxite region of Arkansas, by Noel H Stearn (1930), 80 cents, Information Circular 1, A barite deposit in Hot Spring County, by B Parks and George C Branner (1932), $1, Information Circular 2,

Jan 1, 1933