Search Documents

By H Khoshrou, A Siamaki

Blast designs can have productive and non-productive impacts on downstream stages, mine productivity and operating costs. On the other hand, ground vibration, fragmentation, and back break caused by blasting impose damage and financial penalties and which must be controlled by blast design. One of the significant variables in blast design is the burden. In this study, the potentials of artificial neural network are investigated in prediction of burden in the Sungun copper open-pit mine. Input data were assembled through 18 blasting blocks according to different levels and experimental geomechanical investigation. To construct the model blastability index, uniaxial compression strength, hole diameter, specific weight of rock, rock quality designation and cohesion strength are taken as input parameters, whereas, burden is considered as an output parameter. Mean square error was used as the performance function and back propagation algorithm as the training function, containing four hidden layers and 14 data sets. Four sets of data were used to make sure that correct training had been carried out. This produced the coefficient correlation of 0.662.

Sep 26, 2011

By L J. Strachan, O J. Hawes, S W. Crossen, R C. Roberts

The Albany Conglomerate is a widespread geological unit found in northern areas of Auckland, New Zealand. It has previously been described as part of the early Miocene Waitemata Group which underlies most of Auckland. Much of the Waitemata Group comprises weak interbedded sandstones and mudstones, but also includes conspicuous conglomeratic units such as the Albany Conglomerate. The Albany Conglomerate comprises a well-cemented mixture of hard pebbles, cobbles and boulders of igneous and metamorphic derivation in lenticular beds. A number of tunnelling projects are planned for the near future in Auckland. Recent experience has shown that the variable features associated with the Albany Conglomerate can make selecting appropriate construction methods very challenging. This paper explores the engineering geological and sedimentological features of the Albany Conglomerate with respect to other conglomerates within the Waitemata Group and the potential implications on tunnelling projects in Auckland. Consideration is given to the extent of proposed geotechnical investigations and the production of geotechnical baseline reports.CITATION:Roberts, R C, Hawes, O J, Crossen, S W and Strachan, L J, 2014. Underground construction challenges associated with the Albany Conglomerate in Auckland, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 195–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By C A. Foss, D A. Clark, D Hillan

While magnetic surveys are the most common geophysical method used in mineral exploration, magnetics and geology remain to be fully integrated quantitatively in iron ore provinces. Although high-resolution aeromagnetic data has been collected over prospective areas of the Hamersley Province, much of the information in the data sets has hitherto not been fully exploited due to a lack of suitable interpretation methods. Recent advances in the processing and modelling of magnetics in highly magnetic terrains, constrained inversion and 3D visualisation and understanding the magnetic properties of banded iron formations and iron ores potentially create the capability to generate realistic 3D mapping of magnetite and hematite concentrations over large areas. Initial processing of conventional total magnetic intensity data produces true potential field maps that are unaffected by local perturbations of the regional geomagnetic field direction by intense local anomalies. The true potential field can be converted into vector and tensor components, each of which emphasises different structural features of the geology. Scalar quantities derived from these components simplify interpretation, using new methods, developed by CSIRO and elsewhere, that are less sensitive to magnetisation direction. Preliminary interpretations allow interpolation between mapped units and structures and evaluation of remanence and anisotropy effects. Accurate modelling requires rigourous treatment of self-demagnetisation and magnetic interaction effects. Semi-automated constrained inversion, combining magnetics with available geological information and other geophysical data, can be utilised to generate models of disposition of major magnetic units and the 3D magnetisation distribution within them. The final stage of interpretation is to exploit the understanding of magnetic properties (susceptibility, anisotropy and remanence) developed over many studies by CSIRO, the University of Western Australia and others to convert the interpreted magnetisation distributions into 3D maps of magnetite and hematite contents, which are the quantities of direct exploration interest.CITATION:Clark, D A, Foss, C A, Austin, J and Hillan, D, 2015. Three-dimensional mapping of magnetite and hematite concentrations from reprocessing of detailed aeromagnetic data, in Proceedings Iron Ore 2015, pp 229–240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By C. K. Leith

THE resolution presented at the Annual Meeting of the A.I.M.E., calling on Congress to provide now for postwar accumulation of mineral stock piles under Government control, expresses, I think, the nearly unanimous view of the mining industry. As a result of the trying experiences of the first World War, Mr. Baruch, in his report of Dec. 24, 1919, to the President, urged that steps be taken at once to ensure adequate supplies of raw materials for future emergency. In the twenty years that followed, the same program was vigorously urged on Congress by many individuals and agencies, public and private, including the Secretaries of War and Navy, many members of Congress, the Bureau of Mines, the Planning Committee for Mineral Policy appointed by President Roosevelt, the A.I.M.E., the Mining and Metallurgical Society, and others.

Jan 1, 1943

By E. A. Rychkun

Mining and environmental objectives have traditionally been in conflict. This conflict reflects a delicate balance between the need to spend money to protect the environment, and the need to save money by extracting minerals efficiently. In an increasing number of cases, profit margins diminish rapidly with new environmental regulations and reactionary measures. Forced cleanups and increasing restrictions are unwelcome expensive processes. A practical solution lies in planning rather than reacting. This requires the ability to precisely quantify and qualify environmentally sensitive problems by providing effective engineering tools to model, visualize and analyze subsurface conditions. Prevention of environmental conflicts, and effective cost control are both rooted in the mining company's ability to construct accurate models, monitor changes, assess contamination risks and to design effective remediation plan. This paper presents a case study where these issues are addresses through the application of a new and innovative technology.

Jan 1, 1993

By Riggin P. R.

"IntroductionIndustrial Relations combines two very important relationships - employee relations and union relations.Employee relations always come into play when people are hired to perform tasks. Because mineral processing plants cannot be operated successfully without people, at least not yet, if they ever will be, employee relations must exist in an operatingplant.If the employees choose to be represented by a union, then a relationship with the union as an institution also comes into play. It is very important to note that unionization does not mean that the employee relationship is replaced by a relationship with the union. The latter is superimposed on the former, but it does not replace it. Similarities and overlaps in the two relationships will be present, some of which are of fundamental importance. Nevertheless, they are two different relationships and the reader should bear this in mind when reviewing those parts of this chapter which discuss unionization, collective bargaining, collective agreements, and work stoppages.These two important relationships, which we have chosen to combine and call industrial relations, have crucial roles to play in the social system which interrelates people performing the necessary tasks involved in the operation and maintenance of a plant. The technological organization - equipment, process layout and so forth - and this social system are interdependent and complementary. This chapter attempts to show that the potential level of effectiveness of both the technological organization and the social system depends on the recognition and nurturing of this nexus between them.Occupational health and safety and training are subjects for another chapter. But, both of these have been critical and longstanding employee relations topics . They are destined to take on added importance in the future. As issues in collective bargaining, they are also attracting increasing attention in all union relations. It is hoped that the reader will not isolate from industrial relations those topics which are being dealt with in another chapter. They are very much a part of it and we cannot refrain from making some reference to them."

Jan 1, 1989

By Robert R. Dorfler

AMPS[. has completed a rationed grinding ball test in a 2.93 m x 2.93 m ball mill at Climax Molybdenum Company. The test consisted of purging the ball distribution formed by charging 100%, 76 mm carbon steel balls with a distribution formed by charging 50% 76 mm and 20% 51 mm alloy steel balls. The resulting change in ball surface area yielded improvements in both tons ground and fineness of grind with a significant reduction in total ball consumption. This paper summarizes preliminary studies leading to the plant test, grinding efficiency results, and future plans to optimize the ball charge.

Jan 1, 1981

By F. M. McEvoy, E. J. Steadman, R. Murfin

In England, the provision of aggregate is determined by the historical relationship between construction and aggregate consumption. This approach does not necessarily lead to sustainable decision-making and can be seen as being driven by political expediency, rather than reasonable environmental consideration. The introduction of the statutory requirement for Strategic Environmental Assessment (SEA) in the UK has provided the opportunity to examine this issue on a more rational basis. This paper provides a practical application of a SEA based approach, to the provision of aggregates at a regional level. The process, underpinned by relevant information on resources and environmental assets, suggests that alternative supply scenarios for aggregate provision are tested in a transparent, consistent manner with increased genuine stakeholder consultation. It supports a move away from "predict and provide" approaches to one where aggregates are sourced with the best balance of environmental costs and benefits.

Jan 1, 2005

By J. Cheung, H. Rabia

The traditional methods for predicting mine air temperatures are based on steady state heat transfer models as developed by Voss (1969) and Starfield (1983). These models are useful in providing approximate predictions of air temperatures in trunk and gate roadways. More complex models are required to provide predictions along faces. In practice, the heat flow in underground mines is of transient nature and recent observations in some British Coal mines show temperature variations of up to 5°C during a working week at any one point. In addition, the recent introduction of district recirculation of mine air in British mines requires a more precise prediction of air temperatures during start up of the system or during breakdown. A transient heat transfer theory based on the work of Jordon is presented. The method lends itself easily to computers due to the large number of calculations involved. The proposed transient model is validated using actual temperature data collected in roadways in Wearmouth Colliery in the North East of England. The transient results are compared with the steady state predictions of Voss (1969). Finally, predictions of air temperature in roadways for a recirculation system will be made using both the transient and steady state models. Temperature predictions along faces will be made using a separate model.

Jan 1, 1989

By Matthew Grzelak, Gulsah Erinc, David R. Chapman

"The third phase of the Bagram Drainage System project at Bagram Air Force Base in Afghanistan included construction of a shallow, 540-m long, 1.8-m inside diameter drainage tunnel. The tunnel penetrated mostly stiff to hard clayey and silty soils. The contractor’s Value Engineering Change Proposal (VECP) to use pipe-jacking with a microtunnel boring machine (MTBM) instead of the specified two-pass Earth Pressure Balance method was evaluated and supported using hand calculations. Contractor support was provided throughout the project by providing design reviews and instrumentation monitoring during construction. This paper compares the value-engineering proposal to the specified method and describes the construction conditions encountered. INTRODUCTION As part of a larger improvement project at the Bagram Air Force Base in Afghanistan, a shallow, 540-m long, 1.8-m inside diameter drainage tunnel was constructed to provide additional capacity for Coyote Creek to pass below several critical structures, including taxiways and the main runway, for mitigation of recurring flooding (see Figures 1 and 2). Overburden over the tunnel crown ranged from about 3 m to 5.5 m. An existing cast-in-place twin barrel concrete culvert runs approximately parallel to the new tunnel and is within about 8 m at its closest point. The contractor’s Value Engineering Change Proposal (VECP) to the specified two-pass Earth Pressure Balance (EPB) method (steel ribs and lagging or steel liner plate with a carrier pipe later grouted in-place) called for installation of the required drainage pipe by pipe-jacking (one-pass installation) using a slurry microtunnel boring machine (MTBM). The critical nature of the operations at the air base resulted in significant construction coordination challenges and a greater than usual need to avoid excessive settlements. Substantial restrictions were placed on drilling of investigative borings and installing instrumentation near runways and taxiways due to drill mast height. The prime contractor was SERKA TAAHHUT INSAAT A. S. (SERKA), the microtunneling subcontractor was Ludwig Pfeiffer Microtunnel GmbH & Co.KG (Pfeiffer), the jacking pipe designer was Gollwitzer Pipe and Shaft Technology GmbH (Gollwitzer), and the contractor’s tunnel engineer was Lachel & Associates, Inc. (Lachel). Lachel provided contractor support throughout the project including preparation of a VECP/Design Summary (including interpretation of existing and new geotechnical information), design reviews for jacking pipe, estimating settlement of an existing drainage structure above the new tunnel, and instrumentation planning, monitoring, and analysis during construction."

Jan 1, 2016

By Richard C. Holmquist

Some of you may be old enough to remember -- as I do -- the early days of World War II. A highly prepared, well-equipped Japanese striking force had moved like lightning across the South Pacific islands and Southeastern Asia. As the invasion force pushed its way down the Malaysian Peninsula, Singapore stood serene and beautiful, protected by its natural moat of water, busy as ever with its commercial pursuits. One can see its captains of trade and industry now, sitting com¬fortably on the veranda of the "Singapore Country Club", sipping scotch between cricket games, convinced that the weary, logistically extended Japanese force couldn't possibly cross over to their island which had been so secure for a hundred' years or more. No need to remind you what happened. The brave men in their ships at sea and in the gun emplacements ashore were hopelessly out-gunned and out-maneuvered.

Jan 1, 1979

By Harald Laux, Stein Tore Johansen

The plunging jet in tapping of steel from converters or electric arc furnaces entrains gas into the steel bath contained in a ladle. Gas entrainment rate and the effect of the gas on the flow pattern in the ladle are studied by means of Computational Fluid Dynamics CFD. The work focuses on the mathematical modeling. Two numerical methods, one for free-surface flows and one for dispersed multiphase flow are combined. A transport equation for the average bubble diameter that incorporates the effect of coalescence and breakup is presented. Results from computations for one ladle and tapping configuration are shown. Our findings indicate that the gas entrainment rate is affected by the material properties of the liquid in the sense that the material properties determine the shape of the jet. Moreover, bubble sizes in the range of two-orders of magnitude are predicted in the ladle. The dispersed diameter model seems to work well. It showed the expected response to material parameters and the turbulent field. However, the presented analysis is just a first step that was limited due to certain simplifications. In order to obtain better insight in the tapping process improvements of the analysis seem necessary.

Jan 1, 1999

By J C. Carlile

Many low sulphidation epizonal gold and zinc-lead vein deposits within magmatic arcs are situated on basement highs, and post-date both the main volcanic episode and porphyry copper (gold) mineralisation. These features are best explained by emplacement of a flat batholith a few kilometres beneath each mineral district, as recently demonstrated by geophysical data in the Baia Mare district of Romania. The batholith provides heat for the hydrothermal system, and results in extensional faulting both through up-doming of the overlying rocks, and in some arcs through incipient collapse of the thermally weakened crust under regional extensional stress. More water-rich magmas emplaced at greater depths could explain some deep epizonal and mesothermal gold deposits situated outside magmatic arcs.

Jan 1, 1995

By Keith L. Harris

The performance of the world economy improved significantly in 1984. Real world output!/ grew 4.3% (compared with 2.6% in 19831, the highest since the 4.4% increase recorded in 1978 (table 1). The output of industrial nations rose 4.9%, while that of the developing nations rose 3.7%. The United States and Japan had the largest increases in output of the major industrial nations, with respective increases of 6.8% and 5.8% (table 2). The components of real output with the most significant growth in the industrial countries were gross fixed investment (9.2%), consumer expenditure (3.1%), and public consumption (2.5%) (table 1). Industrial output, as measured by industrial production indices, has returned to about the 1980 level for most of the major industrial nations (table 2). Exceptions to this were industrial production in Japan and the United States; Japan's industrial production rose steadily throughout the 5-yr period and is now more than 16% above the 1980 level, and the industrial production index for the United States reached 11 1.2 (1980=100.0). Real total domestic demand grew at 8.7% in the United States, more than double the rate of Japan, which, at 4.0%, had the second-largest growth. Average demand for all industrial countries was up 5.1%. During 1984 the U.S. dollar showed great strength on international markets, contributing to large current-dollar negative net exports of goods and services and even larger negative net exports of the merchandise sector. While growing U.S. imports helped spread the benefits of the recovery, they also led to a widening of current account imbalances and growing trade tensions throughout the world.3/, 4/

Jan 1, 1985

By Meyer Klein

Decision theory is the formal theory of the logic of decisions in view of the decision maker's objectives, preferences, I beliefs, and available information, It usually deals with weighty economic problems involving irrevocable (or costly to reverse) decisions. Capital investment planning problems constitute an instance par excellence for application of the decision theory concepts. Decision theory as it is presently conceived has evolved in recent years. At first it concentrated on decisions in the face of total lack of information and on games with intelligent adversaries. The results of these efforts proved theoretically interesting, but practically of little applicability. In the last few years, stress has shifted to the introduction of subjective probabilities and preferences, and the results have been eminently successful in applications both in government and with- in business firms in the resolution of complex problems.

Jan 1, 1970

By Donna D. Harbuck

The Bureau of Mines has investigated a process to produce titanium powder directly from titanium salts. If successful, such a process could lower the cost and increase the use of titanium. In this study, K2TiF6, K2TiF3, and TiF3 were reduced with potassium in the temperature range of 650° to 750° C. Under certain conditions, titanium powder 1.6 to 3.3 microns in size was produced. After leaching the product with a 0.1M HCl solution, powder impurities as low as 0.04 pct potassium and 0.28 pct fluorine were obtained. However, oxygen levels of over 1 pct and the frequent formation of insoluble byproducts demonstrate the need for further research to make the powder suitable for powder metallurgy applications.

Jan 1, 2011

By JOHN R. SUMAN

OVERWHELMING proof of the importance of oil in a modern national economy is afforded by the present European War. Treat¬ies and national boundaries have been cynically violated to secure greater supplies of the precious fuel. Petroleum substitutes have been desperately, and far from successfully, sought. The whole German military theory of the drang nach Osten, the drive to the East, is directed at cutting the British supply of oil and securing a supply for Germany. This is a war of machines, and the machines of war feed hungrily on oil. In view of this fact, it is surely comforting to know that we are living today in a nation which has surpassed all the rest of the world not merely in unearthing the raw supplies of petroleum which lie beneath its surface but also in every phase of the industry in mining, refining, processing, production, and distribution.

Jan 1, 1941

By John C. Machisak

Injury data and experience, with related employment statistics, at coal mines in the United States for 1960 are presented in this publication under the following general sections: A General injury experience: Tables 1 to 6: Current data on number of injuries, decree of injury, frequency and severity rates, average severity, and related employment and production data by work location. B Selected injury experience: Tables 7 to 38: Current data on principal agencies of injuries, distribution of injuries by part of body injured, days of disability, extent of hand and machine loading, experience by employment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation?s coal mines.

Jan 1, 1962

By Lloyd W. Trevoy

Titanium and zirconium heavy minerals occur in the tailings streams from processing plants which use the hot-water extraction process for recovery of bitumen from tar sand. In a research program conducted by Syncrude Canada Limited, the crude tailings stream was upgraded to produce quality zircon and titanium mineral products. To process the tailings through conventional upgrading equipment, bitumen residues must first be removed from the mineral grains. Then, by gravity separation, fines and coarse sand grains were removed and a 71% heavy minerals concentrate was prepared which was further separated by high-tension equipment into zircon and titanium minerals concentrates. The zircon concentrate was upgraded by gravity, magnetic and high-tension cleaning to produce a high-quality 98% zircon product. The titanium minerals concentrate was separated into rutile, leucoxene and ilmenite fractions. Heavy minerals distribution in tar sand drilling core samples has been evaluated for various locations on Syncrude Lease 17, and expected annual production levels of heavy minerals have been estimated. A preliminary evaluation has been made of the potential for zircon, leucoxene and rutile production and for further upgrading of ilmenite and leucoxene to synthetic rutile for titanium dioxide pigment production.

Jan 1, 1978

By Joseph Berman

The wolframite mineral series was studied to determine the effect of the FeO - MnO ratio on unit cell symmetry and thermal stability. This work was undertaken to evaluate the analytical procedures now in use for wolframite in scheelite and to aid in the development of improved methods of analysis. Wolframite grains were hand-picked, crushed, and screened; impurities were removed by selective magnetic separations using a Frantz isodynamic separator. The samples were further checked by optical spectroscopic and microscopic examination.

Jan 1, 1957