Search Documents

By W. G. Woolf, E. R. Crutcher

The electrolytic zinc plant of the Sullivan Mining Co. is in Government Gulch, at Silver King, Shoshone County, Idaho, in the Coeur d'Alene mining district, about one mile from the Bunker Hill smelter and about three miles from Kellogg. The Sullivan Mining Co., which owns both the zinc plant and the Star mine, is itself owned jointly by the Bunker Hill & Sullivan Mining & Concentrating Co, and the Hecla Mining Company. The Tainton high-density, high-acid process is used at this plant, therefore some parts of its flowsheet differ markedly from those of electrolytic plants using the low-density process. While it is a custom plant and has treated a variety of zinc concentrates originating from various sources in a number of states, it has obtained its main supply of zinc concentrates chiefly from the zinc-bearing ores of the Coeur d'A1ene mining district, of which the principal important sources have been the Bunker Hill and Star mines. Thus the main feed has been zinc concentrates obtained from complex lead-zinc-silver ores. For the year of 1935 the concentrates had the following composition: water, 9.5 per cent; Zn, 50.6; Pb, 3.3; Fe, 9.4; S, 31.0; Cu, 0.2; insoluble, 2.9. Flowsheet The concentrates are delivered to the plant in railroad cars, which discharge into storage bins directly under the track. Bottom-dump cars are dropped directly into the bins while a slip scraper, pulled by an air tugger hoist, is used to empty box cars. There are five storage bins for concentrates, each of approximately 300 tons capacity. At the bottom of each bin there are individual belt feeders that discharge onto a common conveyor belt, which in turn discharges to another belt that carries the concentrate onto a weightometer belt for weighing. Immediately after the weighing, the crushed oversize return from the roasters is added to the load on the belt and then the ground-up sweepings, lumps and roaster cleanings. An electromagnet at the end of this conveyor removes tramp iron from the feed. The belt discharges to a set of 30 by 12-in. rolls, which break up lumps or frozen chunks of concentrate, etc. Beneath the rolls there is a screw conveyor, which conveys the roll discharge to a

Jan 1, 1937

By Edward J. Karkoska

The film you see is a slow motion view of a typical half million ton taconite blast at one of Erie's mines. This blast is made up of 220 drill holes and a total of 325 thousand pounds of blasting agent. The second view of the same shot is taken by a remote control hi speed camera located 1500' directly in front of the blast. Shortly you will see some violent camera movement as the air blast shock wave strikes the camera location. As the blasting sequence progresses the rock fly becomes evident, and if you will look closely amidst the clouds of smoke, rock fragments weighing up to 1/2 ton begin to cascade into view. These missles are the chief concern of blast security. The next camera shot at 4000 frames/second vividly describes the primacord firing lines detonating the blast. Travelling at 22,000 ft./sec., this white snake of fire travels to each hole, detonating the blasting agent. Before we get into the matter of blast security, let me locate our operation for those of you not acquainted with Minnesota's iron ranges and tell you something about our company.

Jan 1, 1969

By Rafael Arthur Reghine Giorjão

Microestrutura e propriedades mecânicas de tubos de aço inoxidável superduplex SAF 2507 processados por soldagem por atrito com pino não consumível foram analisadas. Juntas de alta qualidade foram produzidas com sucesso utilizando ferramentas de nitreto de boro cúbico policristalino (PCBN), controle de força de 38 kN, velocidade de avanço de 50 mm/min, velocidade de rotação de 200 RPM. Ensaios de dureza e tração foram realizados, evidenciando aumento de dureza na zona de mistura e falha no metal de base. Simulações térmicas calcularam temperaturas globais máximas em torno de 1176 °C e diferentes ciclos térmicos ao longo da espessura da junta, conferindo diferenças microestruturais e mecânicas nestas regiões

Oct 30, 2017

By R. T. MacMillan

Many bench-scale tests and studies have been conducted in developing and testing a chloride-volatilization procedure Ear treating low-grade manganese ore from the Maple Mountain-Hovey Mountain deposit of Aroostook County, Maine. The ore, averaging 10 to 12 percent Mn, contains manganese in several forms and is resistant to concentration or extraction by usual physical and chemical procedures. Over 90 percent of the manganese, content of the ore has been recovered using a chloridizing roast in which the ore was heated at 950°-9b0' C. in a circulating stream of hydrochloric acid gas. Chlorides of manganese and iron were volatilized and swept to a fume collector, where they were condensed and separated from the [as] stream. Operation of a small, 1-pound-per-hour shaft Furnace produced enough chlorides for studying other factors in an integrated process such as: (1) Conversion of the chlorides to oxides; (2) recovery of HC1 gas of suitable concentration Ear recycling to the chloridizer; and (3) control of the Mn-Fe ratio in the oxide product to produce a suitable feed for ferromanganese production.

Jan 1, 1956

By Elizabeth A. Johnson

The vaporization thermodynamics of the aluminum-silicon carbides Al4SiC4 and Al8SiC7 were studied by the Bureau of Mines over the temperature range of approximately 1,500 to 1,700 K. Vapor pressures were measured by a Knudsen effusion-mass spectrometry technique in which powdered samples were effused from graphite crucibles through small orifices. For each compound, a total of six orifice diameters was tested to verify equilibrium within the cell. Aluminum, mass number 27, was the only vapor species detected over the range 4 to 200 amu. Experimental results are based on the following equations for incongruent decomposition: A14SiC4(cr) - 4A1(g) + SiC(a,hex) + 3C(gr); Al8SiC7(cr) - 8A1(g) + SiC(a,hex) + 6C(gr). The observed vapor pressure-temperature relationships determined with a cell orifice area of 2.0 x 10-3 cm2 for Al4SiC4 and 1.81 x 10-3 cm2 for A18SiC7 are the following: Log P - (-18,682/T) + 12.476, for Al4SiC4 (1,550 to 1,643 K) and Log P = (-19,308/T) + 12.421, for Al8SiC7 (1,526 to 1,784 K), with P in pascals and T in kelvins. Third-law analysis of the data provided the following heats of formation: A14SiC4 ?H at 298.15 K - -50.0 kcal/mol and A18SiC7 ?H at 298.15 K - -92.1 kcal/mol.

Jan 1, 2011

By J Safarian, D Hariswijaya

Treating bauxite residue as an alternative source of metals for iron and aluminium industry is an approach to promote circular economy in metal industries. Reduction of metal oxides with H2-based process is an important step on decarbonisation of metal industry. In this study bauxite residue pellets were prepared and were reduced with different H2-H2O gas compositions at different temperatures which yielded with various degrees of reduction. The bauxite residue pellets were made from a mixture of bauxite residue and Ca(OH)2 powders and sintered at 1150°C. Hydrogen reduction was carried out on the oxide pellets using a resistance furnace at elevated temperatures in controlled reduction atmosphere of H2-H2O gas mixtures which resulted in reduction of iron oxides in the pellets. Unreduced and reduced pellets were subsequently heated to 1400°C to study their smelting behaviour using differential thermal analysis (DTA) and thermogravimetric analysis (TGA) technique to investigate the evolution of phases related to slag formation via smelting. Equilibrium module of Factsage™ ver 8.1 was utilised to analyse results of thermal analysis. It was observed that Tricalcium phosphate-β (CaP2O8), Bredigite (Ca7Si4MgO16), Rankinite (Ca3Si2O7), and calcium alumino ferrite (Ca[Al,Fe]6O10) were formed during thermal analysis as intermediate phases. The initial slag formation for sintered and reduced pellets occurred at 900°C which mainly contains calcium and small amount of strontium component. The slag formation rate increases significantly starting from 1100°C when iron oxides started to form initial molten slag phase which then followed by other oxides dissolution in the system. Gas formation was observed at 1180°C and it was found that the gas to be released from unreduced pellets is O2 meanwhile the gas to be released from reduced pellets is SO2 gas. Gas formation rate for both pellets start to increase at 1280°C when the remaining chemically bonded gas start to be released from the system.

Jun 19, 2024

By A Scott, I Onederra

A great deal of technical and research effort has been applied to the development of models to predict fragmentation from rock blasting. A number of quite useful empirical or engineering models are currently available to blasting engineers and consultants, while more sophisticated approaches using mechanistic and numerical descriptions of rock breakage continue to be developed and applied by researchers and explosives companies.The fragmentation resulting from any blast will be heavily dependent on the properties of the rock mass being blasted; however, most empirical models rely on ‘rock factors’ generated from simple rock mass properties to describe the influence of the rock on the blasting outcome. In contrast, mechanistic models need explicit rock mass properties that require sophisticated laboratory measurements and detailed structural data if realistic outcomes are to be generated. The fragmentation modeller is caught between excessively simple rock mass descriptions for the empirical models and excessively complex data requirements for the mechanistic models.This paper briefly reviews the basis of a range of fragmentation models and the rock mass properties on which they rely. Shortcomings in the way that the mining industry tends to characterise the blasting properties of rock are discussed and some practical approaches are described to quantify these properties in both operating and greenfield mining environments. Case studies are presented where specific additional breakage properties and modelling features have been needed to generate a useful description of the fragmentation achieved.CITATION:Scott, A and Onederra, I, 2015. Characterising rock mass properties for fragmentation modelling, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 149–160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Eduardo Poltronieri Trés, Anderson Denadai Thomazini, Rodrigo Boyer Fernandes, Francisco de Assis Dutra Macedo, Gilvandro Bueno, Maycon Athayde, Rossano Augusto Pilon Nunes

The fundamental importance of comminution by high-pressure grinding roll (HPGR) technology to efficiently increase the particle surface area lies in lower energy and water consumptions for iron ore pellet feed production. This study compared the ball wet milling process with the innovative HPGR processing technology for hematite-goethite ores. Green-pellet balling and induration processes were simulated on the bench and pilot scales.

By G. I. McPhail

The authors have conducted several investigations into the prediction of the beach profile of high-density tailings and have found that there are a number of important considerations that need to be taken into account over and above the reliability of the beach profile prediction methodology. These considerations relate to the chemistry of the slurry and specifically the influence of pH and flocculation, both of which have a significant influence on the rheology of the slurry at the discharge point. A number of examples are discussed and a potential testing protocol that will assist in assessing the influence of chemistry ahead of the beach profile predictions is presented. A methodology for assimilating the results of the testing into the likely field situation is discussed, and suggestions are made on application of the results in beach profile prediction. The suspected influence of residual flocculation on the stratification

Jan 1, 2012

By G. Reed Marchant

In 1967 the US Congress passed the "Clean Air Act." This act was amended in 1970. As a result it soon became obvious that American industries were going to have to make significant changes in their methods of operation to be able to comply with quickly developing federal regulations. One of the first regulations developed was on sulfur dioxide. For this reason, the nonferrous smelting industry was immediately affected by these new regulations. This is true because the smelting process produces sulfur dioxide as a natural product of combustion when the sulfur-bearing ore is oxidized to purify the metal. The federal government's approach for setting standards included public hearings at which government, industry, and private citizens were allowed to make comments. For this reason, it was apparent to Kennecott's Metal Mining Div. that it was desirable to make a maximum effort in working with the agency to see that correct input was provided at the hearings to assist the government in setting fair and realistic standards. It was also obvious that more complete monitoring would be required. It soon became apparent that the efforts required input from many levels of the corporation from the chief executive to the plant operators. In order to accomplish both the administrative and the technical needs, an organization was needed that could respond quickly to these needs, obtain information from diverse sources, and bring it to focus in an organized approach to the problem.

Jan 1, 1979

By D. J. MacKinnon

Zinc metal was first produced in India around 1100 A.O. and a zinc industry based on retorting gradually developed in both India and China(1) . The vertical retort method for smelting zinc ores was developed in England in the 1730s; this was followed by the more fuel efficient horizontal retort process developed by the Belgians in the 19th century(2) . The horizontal retort process was the standard method of zinc manufacture until the 1950s when it became obvious that it could not compete with electrolytic zinc technology(2). The present day extractive metallurgy of zinc is dominated by the electrolytic process which now accounts for almost 80% of the world's primary zinc production. In recent years the electrolytic zinc process has seen significant improvements: the fluid-bed roasting of zinc concentrates, improved leaching and residue treatment techniques such as the jarosite and goethite processes, improved solution purification procedures, mechanization of the zinc electrolysis step and of the zinc melting and casting operation. In addition, new leaching processes have been implemented for the treatment of oxidized ores, particularly silicates, and the pressure leaching of zinc sulphide concentrates is now a commercial reality. Although the electrolytic zinc process was first used on a commercial scale in 1916, its history can be traced back to the 1860s. The purpose of the present paper is to outline the early history of the electrolytic zinc process and to trace the significant developments which led to the first successful commercial electrolytic zinc plants.

Jan 1, 1999

By R. P. Fischer

The Colorado Plateau region has been the principal domestic source of uranium, vanadium, and radium. The value of these commodities produced from the region through 1964 slightly exceeds $2 billion. Most of the deposits occur in streamlaid lenses of sandstone in the Chinle and Morrison Formations. The ore minerals below the zone of oxidation are low-valent oxides and silicates of uranium and vanadium; all of these, except the quite stable vanadium silicates, oxidize readily to a variety of high-valent uranium and vanadium minerals. The ore minerals partly replace fossil wood but mainly impregnate sandstone, typically forming tabular ore bodies that are nearly concordant to the bedding of the host rock. The deposits range in size from those containing only a few tons of ore to those containing more than 1 million tons. Stratigraphic, lithologic, and sedimentary structural factors obviously influenced the localization of these deposits, but igneous activity, hydrothermal mineralization, and tectonic structures show no similarly consistent influence on localization. The deposits are epigenetic, but the source of the ore metals, the nature of the ore-bearing solutions, and the time of ore emplacement are uncertain. A few uranium deposits in the region are dominantly discordant to bedding and occur in collapsed breccia pipes or along linear fractures. Their origins are also uncertain.

Jan 1, 1968

By J. O. Marsden

The Candelaria copper-gold mine is located approximately 25 km south and east of Copiapo in Region III, Chile. The original concentrator was designed to treat 28,000 t/d (30,800 stpd) of chalcopyrite-bearing ore through a circuit consisting of a single 11.0 m (36 ft) diameter SAG mill, two ball mills, conventional rougher and scavenger flotation, column cell cleaner flotation, and ceramic disc filtration. The plant was commissioned in August 1994 and quickly reached capacity and expected levels of metallurgical performance. In May 1996, a decision was made to double the capacity of the concentrator by the addition of a second line of equipment. The expanded facilities were commissioned in October 1997, less than 18 months after the decision to proceed, and well within the budget. The original concentrator facilities were replicated or duplicated as much as possible, however, a number of important equipment changes were made to take advantage of industry developments since the original concentrator was designed. These included the use of Eimco 120 m3 (4,200 ft3) cells for rougher and scavenger flotation and the installation of a Svedala VTM -800 Vertimill for regrinding. This paper describes the rationale behind these changes and explores the reasons for the success of the project.

Jan 1, 1999

By B. Berhe, R. D. Lawrence, J. Hinzer

"The fortunes of mining companies and their implied value are tied to cycles - both economic and commodity – within which they operate. Hence the determination of appropriate future metal prices is one of the most critical factors faced by mineral valuators especially for advanced projects. Price, and hence revenue, is usually the most sensitive input to the valuation model. Empirical studies of past forecasts show that the success rate for commodity price forecasting is very poor. This paper explores various approaches and comments on their strengths and weaknesses. We conclude that careful evaluation of long-term metal prices is a key element and is hardly a luxury that can be left to simple averages or rules of thumb. INTRODUCTION Discounted Cash Flow (""DCF"") analysis, is well suited for the valuation of advanced mineral development assets, for which there are identified mineral resources and some form of economic assessment (Pre-Feasibility or Feasibility Study). The DCF method is also the most commonly used method for determining value for such assets. It provides a means of relating the magnitude of expected future cash flows from profits (or losses) to the magnitude of the initial cash flow (investment) needed for capital expenditures to purchase or to develop an asset for commercial production. The method proves useful in making investment decisions as it allows for the quantification of the Net Present Value (“NPV”), as well as the Internal Rate of Return (IRR) and Payback Period on initial investment capital. Valuation by its very nature is a forward-looking exercise. The DCF method attempts to estimate the NPV of expected future cash flows, by selecting factors that will likely affect future cash flow based on informed analysis. One of the most critical and sensitive factors is the determination of appropriate future commodity prices. “The variables that have the greatest impact on a DCF evaluation are the reserves, the metal prices, and the discount rate.”1 The determination of future commodity prices for valuation purpose or during M&A negotiations is a hotly contested issue. There are a number of analysts, institutions and specialized commercial data suppliers that provide both short and long-term commodities price forecasts. Also, the use of an aggregated mean for all available forecasts, or consensus forecasted prices for valuation purposes is not uncommon. The methods used in making forecasts for each forecaster may vary and in many cases may not be publically disclosed. Nonetheless, the aggregated mean of all forecasted commodity prices of reputed institutions is usually taken to “represent the market’s view of likely future commodity prices.”"

Jan 1, 2016

By W. M. Colwell

When it comes to the analysis of gold bearing ore, there are literally dozens of variables that contribute to the final "true value" of a given sample. Initial sample selection, splitting size and method, inherent nugget gold, pulverization method, and analytical method variations are but a few. However, it seems that the inherent nugget gold particle is targeted as the primary reason for intra and inter-laboratory variations in assay. The following study will show that this is not always the case. A series of tests were undertaken for the Aurora Partnership-Aurora Project to solve inter-laboratory variations in the analyses of blasthole cuttings. Initial concern was centered on the probability that free gold occurrence was resulting in erratic results for the mine's cyanide shake assays and outside laboratory fire assays. Comparison of fire assay and cyanide shake assay was sporadically consistent with previously demonstrated extraction percentage for the cyanide method. The goal was to delineate the factors that ensure consistency in analyses; implement, where needed, Good Laboratory Practices; and reestablish acceptable analytical method correlation.

Jan 1, 1993

By Stanislaw Trenczek

Natural hazards such as rock bumps, methane, coal dust explosions, airborne respirable dust, outbursts of gas and rocks, water, radiation caused by natural radioactive materials, spontaneous fires, and climatic hazards, occurring in the Polish hard coal mines, should be controlled. These hazards are characterized by different scale levels numbered from 2?5. To recognize the amount and levels of hazards, research works were carried out in 109 mining districts of mines belonging to Jastrzebska Spólka Weglowa, Katowicki Holding Weglowy and Kompania Weglowa. These are 86 % of all mines and could be regarded as representative of the majority of Polish mining. The hazards have been classified as regards the frequency of their occurrence as: commonly occurring ? with a frequency of 100 % (like airborne respirable dust and fire hazards), high occurrence frequency ? frequency from 60 to below 100 % (methane hazard ? 83.5 %, coal dust explosion hazard ? 92.0 %, and water hazard ? 99.1 %), medium occurrence frequency ? from 30 to below 60 % (rock-bump hazard ? 52.3 % and climatic hazards ? 51.4 %), and episodic occurrence frequency ? below 30 % (outburst of gas and rocks and radioactive hazards). The dynamics of effects of growth in hazard levels to their intolerable values is diverse. Some of them are passive in nature, which allows for longer observation of changes and appropriate early response (as for climatic and spontaneous fire hazards). However the majority of them take on the character of disasters, like methane or coal dust explosions and damage of the excavation structure ? as occurs after a rock-bump or rock outburst; and creation of an atmosphere unfit for breathing ? during open or spontaneous fires, or after gas outbursts containing methane. There are also latent hazards whose effects do not influence indeed a process of production; however they are detrimental to health when a worker is exposed for a long time to airborne respirable dust and radiation. For other types of hazards a level of danger may be only estimated. Since the systems monitoring allows a wider range of control, therefore, aside from rock-bump and methane hazards, there are monitored also fire hazards including measurements of other air parameters (velocity, pressure, humidity, temperature, O2, CO2 concentration). A few types of monitoring systems are used in Polish mines, like the monitoring systems for environmental parameters such as SMP-NT, SMP-NT/A, the telemetric systems CST-40, CST/A, including the computer-aided system for methanometry control officer SWµP, the computer-aided measuring systems KSP-1, KSP-2, KSP-2C, or the production and safety control system VENTURON. The underground part of the systems monitoring of natural hazards contains measuring devices and equipment for automatic control (power-off) of machines and electric devices in case of increased methane hazard. The surface part of the monitoring system allows the measuring data to be visualized and pre-alarm (warning) and alarm states to be displayed. Furthermore it makes it possible to archive and report the data and to control the underground supply and signalling devices. The EMAG Institute developed monitoring methods to extend a measuring range of monitored parameters (such as methane and fire hazards) as well as to monitor so far unmonitored hazards like dust hazards (by continuous monitoring of dust levels in mine air) and climatic hazards (by online monitoring climatic parameters of mine air).

Aug 1, 2013

By J. F. Barkley

"The fly-ash problem of the smoke-abatement engineer - who now might well be titled, ""Smoke and Fly-Ash Abatement Engineer"" - starts with the necessity for him to know what fly ash really is, what plants really create it, and how much is being created. Fly ash in this connection may be defined as all solid particles emitted to the atmosphere as a result of the combustion of fuel.COMPOSITION OF FLY ASHMuch can be learned about fly ash by studying samples with a strong magnifying glass or, preferably, a high-power microscope. As an example, figure 1 is a photomicrograph of an underfeed-stoker fly ash weighing 23.7 pounds per cubic foot, which passed a baffle-type cinder catcher and was caught by a Cottrell precipitator. Figure 2 shows a similar fly ash made at a higher stoker rating and weighing 36.2 pounds per cubic foot. The lighter ash contains more light, unconsolidated ash than the heavier. In both instances some of the ash has been fused to a glass, as is indicated by the spherical particles resembling marbles; however, the heavier dust contains more and larger spheres. With the faster burning and higher air pressures occurring at the higher burning rates, more of the larger fused spheres reached the precipitator.Such studies of fly ash frequently make possible correct determination of its source. For example, the Supreme Court Building, one of the finest of the Federal buildings in Washington, was having considerable difficulty with fly ash from some outside plant. It was thought to come from a nearby apartment house. A fly-ash trap was installed there, and care was taken in the operation of their underfeed stokers. The fly-ash nuisance continued. Microscopic examination of the fly ash found about the building compared with samples taken from the stack of the apartment house showed to the surprise of the accusing building superintendent that the present source was elsewhere. By the same means, the source was found to be a plant about ore-half mile away."

Sep 1, 1939

By L. G. Wiseman

The raw materials processed, highlights of technology used, and products produced at INCO's Copper Cliff Nickel Refinery in Ontario, Canada, are described in this paper. INCO's Bessemer matte separation process yields various nickel and copper products and intermediates. The latter presents the main supply of raw materials for the Refinery. Key features in the Refinery are Top Blown Rotary Converters and the INCO Pressure Carbonyl (IPC) process. Process improvements made since the commissioning of the Refinery in 1973 are also discussed. The Refinery produces a variety of nickel products, including nickel powders. Residue after carbonylation presents an important intermediate enriched in precious metals and cobalt that serves as feed to downstream operations for recovery of the residue's metal values. Also discussed are detection, measurement and control procedures which ensure safe operation.

Jan 1, 1988

By H. J. van Antwerpen

AngloGold Ashanti operates the world`s deepest mine, Mponeng gold mine, in South Africa. A vast refrigeration and ventilation system provides acceptable working conditions 3800m below surface at 60°C rock temperature. In such a system, optimisation and assessment of modifications becomes very difficult. With that in mind, a research project was launched to determine whether recently developed system simulation technology can be applied to a mine as vast and complex as Mponeng. Using the techniques and methods as implemented in FLOWNEX software, it was indeed proven to be possible to do a mine-wide combined simulation of compressed air flow, ventilation air psychrometry and refrigeration water systems. Interactions between the various streams included heat transfer, pressure drop, evaporation and condensation. The simulation model was used in a parametric study to test various water flow and temperature operating points for the refrigeration system. It was found that, given current limitations, the mine refrigeration system is running fairly close to optimal but with some opportunities for improvement. The simulation model also provided useful insight for future changes or extensions to the system.

Feb 23, 2014

One of the important directions of further increase of quality and efficiency of control of mining companies and branches is the creation of the operation and development monitoring systems of such facilities. The main purpose of these systems is to provide managers with reliable and timely information on the current state and typical tendencies of operation of the facilities under control. However until the present time no scientific and methodical ground for system monitoring of the mining companies and branches has been created. Therefore, the authors of the report have aimed to assess the current situation with regard to the researches in this field and to do analysis of the most important aspects and ways of solution of the issue under consideration.

Dec 6, 2010