Search Documents

By M. J. Makhula, R. M. S. Falcon, S. O. Bada, L. M. Falcon

"SynopsisThe combustion and co-combustion behaviour of macadamia nut shell, high-ash coal, and anthracite, along with their blends was studied using thermogravimetry. The reactivities of all samples were analysed in air, oxygen, and CO2 atmospheres and at different heating rates from 10 to 40°C/min. Macadamia shell was found to have a lower ash content, 0.36%, than coal with 27.49% ash. The calorific values were similar, 19.64 MJ/kg and 19.44 MJ/kg respectively. The differential thermogravimetric results indicate that as the heating rates increase the ignition, peak, and burnout temperatures increase significantly, leading to high combustion rates. The interaction between the fuels was evaluated using the weighted average model, and the results indicated that there is more synergetic interaction between 20% macadamia plus 80% coal under oxygen than in air and CO2 atmospheres. The results of the investigation provide the combustion and co-combustion characteristics of various samples and their blends and indicate their combustion compatibilities. IntroductionThe global macadamia nut industry is developing at a very rapid rate. South Africa is currently the world’s third largest producer, with a production of about 35 000 t as of 2012 (Department of Agriculture, Forestry and Fisheries, 2013), compared to 840 t produced in 1996. The greatest numbers of the macadamia nut farms in South Africa can be found in Mpumalanga, Limpopo, and KwaZulu-Natal provinces, with Mpumalanga as the largest producing area. There are many factors influencing the increased demand for macadamia nuts, the most important factor perhaps being their nutritional value (California Dried Fruit and Nuts, 2011; MPC, 2014) and their suitability as a feedstock for manufacturing cosmetics, bakery products, nut paste, chocolates, sauces, and ice-cream. As a fuel, macadamia shell has a high heating value ‘as-fired’ of about 20.71 MJ/kg (Vhathvarothai et al., 2013), which could in turn be used in drying the nust, and the shell could also be milled and applied as a fertilizer."

Jan 1, 2015

By M. Hamamoto, S. Tanaka, K. Noda

"Tamano Smelter or Hibi Kyodo Smelting Co. Ltd. is operating with the Tamano Type Flash Smelting Furnace method which is a flash smelting furnace without slag cleaning furnace but which can discharge a slag equivalent to that from the slag cleaning furnace and with the development or coke combustion technology which is the basis of this world's only one type flash smelting furnace process, the smelter exhibits a low operation cost under high productivity operation. Utilizing this experience and improving it we have developed and put to practice an operation guide system using a general purpose computer in order to further establish s stable operation. In this paper these improvements are described. Background of System DevelopmentWith the recent rapid progress of general purpose computers and improvements in their performance an environment for the use or computer in process simulation at low cost and simple operation has been established. If an accurate operation simulation can be done with the Tamano Type Flash Smelting Furnace the merits would be very great and thus we started development of the system. The official name of this system is Computer guide system for Coke Combustion in the T-FSF and taking the initial letters we call it CCCT. We aim to achieve operation with stable mane grade, temperature and slag loss in the furnace by maintaining the most suitable combustion conditions of concentrate and coke in the flash furnace with the assistance of CCCT to the flash smelting furnace operators.Through several production expansion projects clone in the past by oxygen enrichment the copper concentrate treatment quantity and matte grade have increased step by step as shown in Figure I. Following this increase the difference between the operation calculation results al the initial stage of coke combustion and the actual behavior of furnace (matte grade. temperature in the furnace. etc.) gradually became bigger. Further operation procedures taken by different operators against the same phenomenon were sometimes different depending on each individual, which from time to time caused the operation to become unstable. Prior to the development of the system we checked out thoroughly the weak points of operation calculation procedures which were in practice until that time. The results were analyzed and study was carried out to establish a most suitahle operation calculation procedure and finally we reached this system"

Jan 1, 2000

By Gill Montgomery

The problems of the domestic merchant fluorspar producers are more or less common with those of many other producers of metallic and non-metallic minerals. For more than ten years the American fluorspar producers have seen an ever lowering price in the market-place for the fluorspar product, while their labor and material costs-continue to mount steadily. This cost-price squeeze has forced out of business all but a few of the merchant producers, and only two captive producers continue to operate, and one of them has announced early curtailment. The prices of domestic fluorspar, of all grades, have declined because of the competition from cheaper foreign imports, principally from Mexico, Spain and Italy. Tariff protection on fluorspar, particularly on the highest or acid grade, has never been sufficient to cover the production cost differential between foreign and domestic fluorspars. Low ocean and barge freight rates have also contributed to the barring of the product of domestic mines from, the major consuming centers along the Gulf and East Coast. Because of the freight disadvantage, all but one or two fluorspar producers in the western states have had to suspend business. More than 80% of the domestic fluorspar is being produced in Illinois and Kentucky fluorspar districts which adjoin on both sides of the Ohio River.

Jan 1, 1964

By F. C. Appleyard

As one of the more important Industrials Minerals, gypsum occupies a significant place in the economy of the United States, particularly in that segment which can be loosely called the Construction Industry. For many years, products made from gypsum have been a major building material, and the usefulness and versatility of these products is such that their widespread use is expected to continue. In 1968, according to U.S. Bureau of Mines statistics, the value of all gypsum products sold in the United States was 405,000,000 - and although this value has dipped from the 1964 high of $ 432,000,000, it is expected to trend upward in the next few years to equal and surpass this figure as the construction industry recovers from its current squeeze of "tight money" and high interest rates. There are many factors to be measured in determining the potential value of any mineral deposit, and how it might fit within its particular industry. What, then, are the qualities which a gypsum deposit must have in order to profitably participate in the four hundred million dollar plus business which is the gypsum industry? First let's consider the geology of gypsum, the geographic distribution of deposits, and the more important factors such as size, grade, capital requirements, and operating cost. Then, an understanding of the uses of gypsum, various types of products, and location of markets would be helpful, along with such other factors as the structure of the industry, price trends, etc.

Jan 1, 1970

By W. E. D. Stokes

WHEN history is written, the year of the blitzkrieg will go down as giving aviation its greatest impetus. No perceptible drop in military business, even with cessation of hostilities abroad, seems likely. The combined air force of the U. S. Army and Navy on July 1 was approximately 5000 planes, as against 50,000 planes currently discussed as necessary. Observers at the fronts are giving designers and metallurgists back home some realistic ideas to shoot at. As conventional runways reveal the location of airports to enemy raiders, operating bases are now masked. Difficult, often muddy and rough landing strips, requiring strong landing gears and exacting take-off and maintenance characteristics, are the specifications of war. This is "old stuff" to numerous mining operators in mountainous jungle areas where gradients up to 8 per cent are in more or less common use in such mountain landing fields. Although airplane building is not readily adaptable to assembly-line methods, a trend towards mass productions is now in evidence. Incidentally, a U.S. Army "Curtiss P-40" requires about 10,000 man hours of work to complete and is tied together with 75,000 rivets. During the past year a number of aircraft factories adopted the "shot-

Jan 1, 1941

By Reza Rahimi, M. Nili Ahmadabadi

"Because of high cost and shortage of primary resources of Ni-base superalloys, revert alloys can be used as a part of charging materials for production of superalloys ingots. The current study is based on recycling of IN738LC, a Ni-base superalloy, using 30% and 50% reverted alloy and balanced amount of virgin raw materials. Therefore, it has been attempted to cast an alloy with references to standard chemical composition and mechanical properties. After charging and casting in vacuum melting furnaces, chemical composition verification and non-destructive tests (i.e. Penetration and Radiography Tests), quality of samples were evaluated at elevated temperature by stress-rupture test. Results acquired from chemical composition and mechanical test indicate that cast ingots using 30% and 50% reverted alloy is reliable and consistent with the quality control requirements.IntroductionIn recent years, there have been many fluctuations in cost and availability of raw materials which are extremely determining in Ni-base superalloys production. Accessibility to the high purity metals such as Cobalt, Molybdenum, Tantalum, Niobium and etc. have been problematical during the past decades. Therefore, shortages of critical raw materials beside the economical considerations motivated the alloy suppliers and investigators to study and find alternate sources such as reclamation and recycling of scraps [1].There are a lot of reasons for the necessity of recycling; perhaps the most justifiable one is that consumers themselves produce scraps. For example, the weight of a finished superalloy product could be less than one-third of the cast alloy weight and in the case of complicated machined parts; this portion may reach to one-tenth [2]. High values of constituents, reduction of energy consumption and environmental concerns have all strengthened the obligation of recycling in Ni-base superalloys.Because of the high degree of risk in usage of improper materials for production of turbine blades, a delicately controlled program for recycling is needed. Depending on the type of scraps, this program can define the recycling procedure, required instruments, allowable percentage of scrap for usage and finally confidence level of the process."

Jan 1, 2012

By M. Bueno, T. Chavez Matus, M. S. Powell, S. Michaux, S. Luukkanen

Comminution tests are an essential element in the design of ore beneficiation plants. Many methods have been developed to assess the breakage characteristics of rocks to generate parameters for modelling. However, most of the existing methods are laborious, expensive and require large samples. Consequently, test work has been traditionally conducted with a few representative reference samples. On the other hand, geometallurgical modelling programs require an extensive amount of test work to allow understanding the variability of ore properties within the deposit and establish spatial geometallurgical domains that show the differential responses to mineral processing. Therefore, comminution tests for geometallurgy need to be more efficient in terms of time, cost and sample size. This paper introduces a new testing device (Geopyörä) which is capable of measuring forces and energy applied to rock particles during the breakage process. The new testing method uses smaller samples and can be up to 50 times faster than other commonly used tests in the industry. This paper presents the concept prototype and the preliminary test work results, which have been benchmarked against some of the industry standard tests, such as the JK Drop Weight Test (JKDWT), the SMC Test® and the Bond ball mill test. Keywords: Geometallurgy, comminution, ore breakage characterization, variability.

Jan 1, 2020

By R. B. Tippin

The material balance computer program (MAT-BAL) developed at the Minerals Resource Research Center of the University of Minnesota, has been used in conjunction with routine process profile samples taken in the potash compaction plant at Great Salt Lake Minerals and Chemicals Corporation, Ogden, Utah. In this manner, a uniform data base is being established for the process, and selected key indicators are used for decisions in plant operation and maintenance. With present emphasis on improving product quality and increasing production rates, the standard data base system provides a means of measuring results from test programs to optimize the circuit. The development and application of this process control method is discussed. The compaction plant computer-assisted data base has been in existence for only two years, but it has made significant contributions to the knowledge of the process and continues to assist in monitoring the plant performance. It is anticipated that the material balance program will be adapted to the GSL flotation plant in 1979, and to other circuits in the potassium sulfate chemical plant.

Jan 1, 1979

By T. Takayama Filho

Votorantim Metais Zinco is a smelting facility which produces SHG zinc, zinc alloys, sulfuric acid, liquid SO2, copper sulfate, cadmium metal and silver concentrate. It is located at Juiz de Fora, Minas Gerais State, Brazil. This facility has been operating since 1980 and its current capacity is 95,000 tonnes of zinc per year, using mostly imported sulfide concentrates.The plant uses the conventional roast-leach electrowinning (RLE) process, in which iron is removed from the circuit as jarosite. The residues generated by the RLE process, which amount to about 200 t/day (dry weight), were until 10 years ago, deposited in tailing ponds having no impervious lining. More recently, jarosite and other wastes have been deposited in a properly built reservoir, but this is reaching its maximum capacity. In order to decommission these disposal operations and to reclaim the sites in an environmentally acceptable manner, Votorantim Metais concluded in 2004 a rehabilitation project for the old tailings pond and prepared detailed plans for managing the current and future disposal of jarosite-bearing residues. This paper describes the procedure for removing iron from the hydrometallurgical circuit and discusses the past and current status of the residue disposal sites, as well as the future challenges related to the environmentally acceptable handling of iron residues.

Jan 1, 2006

By M. Copeland

Phase relations of gadolinium alloyed, up to 40 weight-percent (wt pct), with AISI 304-type stainless steel were established. Body-and face-centered cubic iron-rich solid solution phases and several intermetallic gadolinium-containing compounds of variable composition that approximated the formulas Fe9Gd, Ni7Gd2, Ni3Gd, Fe2Gd, NiGd, and NiGd3 were identified. The intermetallic phases Fe9Gd and Ni7Gd2 were noted to melt at about 1,080° C at about 0 to 2 wt pct gadolinium. The melting temperature of Fe9Gd increased with increas-ing gadolinium content to a plateau at about 1,230°C and 30 wt pct gadolinium, and the melting point of Ni7Gd2 decreased to a plateau at 900° C and 30 wt pct gadolinium where Ni3Gd, NiGd, and Fe2Gd coexist. Body-centered cubic iron solid solution was stable from 1 to 2 wt pct gadolinium to higher contents, 30 wt pct gadolinium or possibly more, and face-centered cubic iron up to 12 wt pct gadolinium below 1,200° C. The stability of these phases above 1,200° C was not resolved except for the mel points. A limited number of fabrication variables as well as mechanical and corrosion properties of alloys containing up to 5 wt pct gadolinium were studied. Equilibrating and forming operations were best conducted at about 940° to 1,080° C. Some variability in the yield and tensile strengths of alloys was noted; however, there was a continual decrease in ductility and impact resistance with increasing gadolinium contents. The resistance of gadolinium alloys to corrosion in water at 354° C was about the same as stainless steel.

Jan 1, 1965

By J. I. Gazzarri

A model of solid oxide fuel cell AC impedance behaviour has been developed and is used to simulate the frequency response of a single cell with and without mechanical damage. The results indicate that the presence of mechanically induced damage within the components of a solid oxide fuel cell can be detected by comparing the frequency response of the undamaged cell with that of a cell in which in-plane cracking or delamination has occurred. The presence of such defects manifests itself as a new semicircle in the Nyquist impedance diagram of the full cell. A parametric study reveals the resolution capabilities of the method in terms of the geometrical characteristics of the defects.

Jan 1, 2005

The heat of immersion of coals in different immersional liquids is measured as a function of particle size and moisture content. Decrease in particle size shows a concomitant increase in the heat of immersion. The heat of immersion is dependent upon the nature of immersional fluids. In addition the nature of moisture present in coal influences the heat of immersion.

Jan 1, 1993

By Andrew Scogings

The current edition of The Australasian Joint Ore Reserves Committee (JORC) Code was published in 2012 and, after a transition period, the 2012 edition came into mandatory operation on Dec. 1, 2013. There is a significant change between JORC 2004 (Clause 44) and JORC 2012 (Clause 49) for the reporting of industrial mineral resources and reserves, which should be addressed by ASX-listed players in the industrial minerals space.

By D Martín, G. Díaz, F. Cubeddu, A. B. Mejias

The Modified ZINCEXTM Process (MZP), developed by Técnicas Reunidas, is an industrially proven flexible process. It can handle a wide range of primary and secondary raw materials, producing SHG zinc. The core of the Modified ZINCEXTM Process is the zinc solvent extraction unit. This unit is an effective barrier for any leachable impurities present in the raw material. As a result of this an ultra-pure zinc solution is always obtained. The high versatility of the process makes the application of the technology in different scenarios possible. MZP can be effectively applied when developing a whole new plant (Skorpion) or adapting its scheme to an existing refinery (Akita), in both cases giving the same results. Flexibility in terms of capacity of the plant is a great advantage of the MZP, there is the possibility to adapt the global process to a wide range of production capacities. Zinc production capacities of over 150 000 t/a may be achieved with a single solvent extraction plant train. The robustness of the Modified ZINCEXTM Process has been recently proven on two new plants currently in operation: Portovesme (Italy) and Horsehead (USA) after start up during 2013. The status of both plants is described in this paper.

Jan 1, 2014

By HUNTINGTON ADANS

(Wilkes-Barre Meeting, June, 1911.) THE arrangement of a flow of cyanide-pulp through Pachuca tanks in agitation, so as to permit a continuous process, instead of alternate filling, agitation, and emptying, has been proposed by various writers within the last two years, and more particularly by A. T. Grothe, agent for the Brown patents on Pachuca tanks in Mexico. It was first put into practice, I believe, by M. H. Kuryla at the Esperanza mine in El Oro, Mexico. The starting of agitation in Pachuca tanks after filling may offer no serious difficulties with ores which do not settle rapidly in such tall tanks; and the adaptation of the tanks to continuous agitation under such conditions may give simply a somewhat more convenient method of treatment and greater agitation-capacity for a given number of tanks, because of the saving -of time lost in filling and discharging. But in the treatment .of pulp which tends to settle rapidly, as in the cyaniding of concentrates or of the whole pulp of ores containing heavy sulphides, the packing of the slime at the bottom may, cause much trouble. The use of the radial air-pipe attachments near the top of the cone and of the air-valve outside of the air-lift .tube at the bottom may obviate the difficulty to some extent; but the action of the radial air-pipes on the cone-sides is that -of a sand-blast, and their continuous use cuts through the tanks. Moreover, even when these pipes are used, some pulps will pack tightly below them in the cones. Under such conditions the use of Pachuca tanks with intermittent filling and discharging becomes a troublesome process. Time is lost in ,starting agitation; large quantities of compressed air are wasted; pulp is blown over the tank-tops; and not infrequently it may be necessary to dig out the bottoms of tanks by hand. This trouble is the only important one occurring in the use of Pachuca tanks; and, since it is caused by intermittent filling, the .arrangement of a continuous flow of pulp from tank to tank,

Aug 1, 1911

By P. M. Keyser

Column flotation continues to make inroads into applications traditionally dominated by mechanical flotation cells. For example, columns are becoming more visible as rougher flotation devices. At Royal Mountain King Mine in California, two 2.9 m (9.5 ft) diameter columns are used for rougher flotation of carbon from a gold ore (Orlich et al, 1992). In addition, work performed at BRGM in France demonstrated the superiority of column flotation over mechanical flotation with respect to design of new plants (Morizot et al, 1991). With the mounting evidence, columns can succeed in any flotation application. The primary reasons for this acceptance of columns are a general improvement in design, scale-up and operation as well as improvements in sparger design and performance. With these advances, the full benefits of column flotation can be realized. The benefits of properly designed, aerated and operated flotation columns include: ? Lower Capital Costs ? Reduced Operating Costs ? Fewer Processing Stages ? Improved Metallurgical Performance

Jan 1, 1993

By Varadarajan Seshadri

The performance of mould fluxes in satisfying its quality requirements can have a significant effect on the efficiency of the continuous casting process and on the surface quality of the products. This performance is affected by various parameters including the characteristics of the mould fluxes, the quality of the steel being cast and the operational conditions of the caster. The extremely complex relationships involving the parameters mentioned above make it very difficult to have simple criteria for selecting mould fluxes for casting a certain grade of steel in a continuous casting machine. These difficulties led steelmakers and mould flux suppliers to select mould fluxes based mainly on plant trials. In the present work, a software to help in the analysis and development of mould fluxes for continuous casting was developed_ This software includes several models for prediction of mould flux viscosity and consumption. A mathematical model was also used to predict the heat flux through the mould flux. The proposed methodology was applied to continuous casting of crack sensitive steels_ Some of the results given by this software are presented, discussed and compared to plant data.

Jan 1, 2003

By I Gray

While in some cases it is vitally important to measure the virgin stress in rock prior to tunnelling there are a number of cases where such stress measurement is really not required. The concept of having to have a number to put in a numerical model representing a continuum is often quite inappropriate. This paper discusses the cases when virgin stress measurement is required and the most appropriate means to measure it. The techniques discussed cover all of the overcoring systems, hydrofracture and borehole breakout measurements. It also covers the use of rock surface stress measurement, which is easy to perform and should be used to check for changing stress conditions. Unfortunately this technique has been ignored in recent times because engineers are addicted to numerical models requiring far field stresses rather than measuring the real values that exist where they matter – at the tunnel wall. A case is presented in which the measurement of surface stress in a tunnel boring machine tunnel enabled the far field stress to be determined in what must be the world’s largest overcore.CITATION:Gray, I, 2014. The measurement of rock stress for tunnelling, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 153–160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By S. A. G. Poppen, J. Konopka

"Petro-Canada's project investigative and experimental underground work in the Galt coal seam at Kipp, Alberta included the construction of an emergency egress and ventilation raise from surface.The Galt coal seam is 206 m below the surface and covered by 8 m of shale, sandstone and clay beds of the Oldman Formation, 128 m of shale, bentonite beds and sandstone of the Bearpaw Formation, and 70 m of glacial till and basal gravel. Free water was encountered from sand lenses in the glacial till and the basal gravel.Excavation for the ventilation raise was a nominal 2 m diameter and it was lined with a welded, continuous, steel liner of 1.2 m 1.D.Excavation in the glacial till was carried out with a surface bucket drill rig combined with hand mining. Ground support in the glacial till consisted of liner plates and backfill grout. The Bearpaw and Oldman formations were excavated by employing standard raise boring techniques. The individual liner sections of the continuous steel liner were assembled on surface and the entire liner column was lowered into the raise by employing hydraulic lift climbers. The liner column was back-filled with concrete.IntroductionThe Lethbridge Coal Field comprises an area of approximately 1 165 square km in the vicinity of Lethbridge in southern Alberta. Pacific Petroleums Ltd. proposed in a Preliminary Disclosure in January 1979 ""to open an experimental mine prior to development of a producing underground mine with an initial rate of 540,000 tonnes per year"". A 2 900-hectare group of leases in the Kipp-Coalhurst area was selected as the primary target for the Kipp experimental mine. The scope of work for the experimental mine included the construction of an access shaft with production capabilities, the construction of a ventilation and emergency exit raise, drive-ages in coal to yield a bulk sample, gathering of geotechnical information and the testing of experimental mining methods."

Jan 1, 1983

By E. M. Frizzell

An ongoing research program at the Spokane Research Center of the U.S. Bureau of Mines is directed toward investigating drilling parameters (thrust, torque, penetration rate, and drill revolutions) during the drilling of roof bolt holes. A system that measures these drilling parameters calculates the specific energy of drilling, and determines drill bit position has been developed by the Bureau and mounted on a roof bolting/drilling machine, through the use of a microcomputer, critical drilling parameters can be immediately interpreted and analyzed. This makes it possible to inform the operator of hazardous roof conditions. Initial results of this program are presented here.

Jan 1, 1990