Search Documents

By Jardine G, Woodall C

The Henty Gold Mine, located in Western lasiuania use, uuiusatise solutions to effectively manage a mining operation in an environmentally sensitive setting and has been presented with several environmental awards. Fill is required as part of the mining method to provide passive ground support, minimise rock exposure and ensure maximum recovery of the small but high-grade orebody. The use of the whole portion of leach residue in the backfill reduces the surface tailing disposal requirements. Therefore, High Density Paste Fill (HDPF) has been selected as the most appropriate fill method to meet these objectives. Additional benefits include the minimisation of excess water from fill and the subsequent need for the collection and treatment of water and slimes. There are minimal equipment requirements during placement, thereby optimising mine resources for production. The initial paste fill design was based on the Bad Grund and Ranunelsberg Mines paste fill systems of Preussag in Germany and comprised pumping filtered tailings paste some 1.2 kin uphill from the mill to the mine portal, where cement was to be added before being distributed underground. The system was designed following initial testwork that was undertaken on a bulk sample of ore mined from the scar surface Sill Zone. Subsequently, during the mining of the Zone 96 orehody, it was found that there were significant mineralogical variations in the composition of the ore mined. Following processing, the resultant Icach residue caused significant changes in the paste rheology and therefore the pump and flow characteristics. An alternative solution was implemented that involved the use of agitator trucks to transport the cemented paste to the portal. This required modifications to the fill preparation system and also the underground distribution system. Laboratory strength tests of the HDPF using actual gold plant leach residue showed low early strengths were attained with HDPF containing only filtered leach residue. Therefore, high binder addition rates or an increase in the fill cycle time would be required to allow the fill to gain sufficient strength. A considerable amount of potentially acid generating waste rock also requires underground disposal. By blending the waste rock with the HDPF, the strengths were improved and the required cement addition rate reduced by about one-half. The potentially acid funning waste rock is encapsulated in the highly alkaline cemented paste, minimising the potential for acid generation.

Jan 1, 1998

By R. C. M. van der Spuy

The heavy-minerals plant at the Palabora Mining Company treats 25 to 30 kt of new feed daily. The U3Og value of the ore averages approximately 40 p.p.m. The circuit consists of four stages of upgrading on 68 Reichert cones, fol. lowed by a jig and 30 table decks. The paper describes how feed-distribution problems have been overcome and the methods used for monitoring and controlling the cone performance. The adaptation of a standard jig for the recovery of fine minerals is discussed, and a method of 'table agglomeration, for the recovery of coarse refractory copper sulphide is described. The tables consist of polyurethane-covered fibreglass decks, and their operation is controlled according to measurements of the uranothorianite content of the concentrates and middlings by means of a nuclear scintillation counter. The upgrading ratio of the uranium mineral by gravity concentration is 1000:I, baddeleyite (ZrO.) being recovered as a by product.

Jan 1, 1982

By R. Bruce Thorndycraft

Pinson Mining Company was formed to develop a gold orebody located in northern Nevada near Winnemucca. A feasibility study was undertaken in 1979 by a consortium of three Toronto-based mining companies and a Reno-based exploration company. The study indicated a viable project with gold priced above $225 per ounce. A project manager, and mine and mill superintendents, were hired in late 1979 to expedite the development of a 1000 ton per day mine-mill complex. Plant design engineering was contracted with Industrial Design Corporation in Salt Lake City. Three experienced plant metallurgists representing Pinson were stationed in Salt Lake to guide the work of Industrial Design. Among the many design criteria spelled out by Pinson, foremost were bringing the mill on line as quickly as possible at minimum capital cost. Fourteen months after the beginning of design engineering, the completed Pinson mill became operational. Total capital cost, including mine development, was $18 million. The Pinson project has proved to be far more than viable; the entire capital cost will be recovered within 18 months of the mill start-up.

Jan 1, 1982

By Thomas F. Donnelly

The Province of San Cristobal is situated on the south side of the island of Santo Domingo about 25 miles west of Santo Domingo city, the capital of the republic. The copper mineraliza,tion is found about 8 miles north of the town of San Cristobal,. in the section known as Bucaro Hill; in San Francisco Hill; on the Nigua River; and on the Jaina River. The district is reached by automobile from Santo Domingo city over an excellent road for 25 miles to San Cristobal, and then, by horseback 6 or 8 miles up the Nigua River to what is locally known as "Camp

Jan 1, 1916

Numerical modelling is a valuable tool for simulating the fundamental processes that take place during a heating. The models presented in this paper have enabled a quantitative assessment of the effects of initial pile temperature, pile size and mass and coal particle size on the development of a heating. All of these parameters have a certain criticality in the coal self-heating process.

Jan 1, 2005

By C. E. Arthur

The Bureau of Mines has investigated the problem of radioactive contamination using nuclear explosives to fracture petroleum reservoirs in an attempt to stimulate production. It was concluded that some contamination of petroleum products will almost certainly occur. However) the degree of contamination cannot be predicted except by a full-scale experiment) since simulating the problem in the laboratory is economically impossible because of the extremely high temperatures and pressures that must be reached in extremely short time intervals if a reasonable analog is to result.

Jan 1, 1965

By P. Braga, A. Chaves, S. França, A. Luz

"In Brazil, there are no official reserves of molybdenum, and the unofficial reserves are modest. Therefore, the molybdenum ore (molybdenite) produced as a co-product or by-product of emerald mining in the region of Campo Formoso, BA, has arisen as the only economic option. The flotation process is commonly used in Brazil for the recovery of molybdenite from emerald mining tailings, but it produces low-content molybdenite concentrates, thereby resulting in a product with low economic value. The molybdenite concentrate produced in Campo Formoso contains 83.5% MoS2 (50% Mo), which is less than the international standard product that contains > 90% MoS2 (54% Mo).This low value is due to the presence of talc, which is a naturally hydrophobic mineral that is also floated with the molybdenite during the flotation process. Separability studies were done in a Partridge-Smith cell using dextrin and quebracho as a molybdenite depressor in solution at different concentrations and pH values to produce a technical-grade concentrate (i.e., 90% MoS2). These basic studies were accompanied by measurements of the zeta potential and contact angle, which was determined by the capillary rise method. The results of these floatability studies were used in bench flotation tests, which were performed in a Denver laboratory flotation cell. A molybdenite concentrate of 93.4% MoS2 was obtained when dextrin was used at a concentration of 100 g/t."

Jan 1, 2014

By H W. Scriba

The development and improvement of computer-based process simulation packages over the past 20 years has provided process engineers with a powerful tool to use in the design of complex metallurgical plants. The use of such modelling tools has enabled the design of process plants that minimise operating and capital costs whilst optimising plant efficiency and recovery. Almost every new project developed in the current market is underpinned by a simulation of the process. In line with engineering best practice this simulation should be based on laboratory/pilot plant test work results and sound assumptions. Any errors that are not identified in the development of the process simulation may have significant effects on the final design and operation of the processing plant. Developing a simulation of the process in a comprehensive, logical and auditable manner is thus essential in ensuring the simulation accurately represents the expected process plant behaviour. A methodology that ensures these requirements are met has been developed by SNC-Lavalin Australia and is described in this paper. The methodology includes the major review stages of data collection, model planning, model building and optimisation, model review, scenario testing and options development, and model reporting. All of these stages should incorporate comprehensive client interaction and review by a suitably qualified representative. In applying these methodologies SNC-Lavalin Australia ensures that the process simulation model developed can be confidently utilised in the design of the process plant, and in the estimation of operating and capital costs, whilst ensuring that engineering best practices are met.

Jan 1, 2008

By J. Y. Hwang

Sands are utilized to make molds for metal castings in the foundry industry. Approximately a half ton of sand is disposed of for each ton of metal cast in this country. In Michigan, annual sand disposal amounts to about one million tons. A process has been developed in this study to reclaim sands from a steel foundry. Physical separations are utilized in conjunction with other operations (such as the removal of binder, metal, spruce, washes, etc.) to yield silica and chromite sands with desirable molding properties. Several different separation methods, including electrostatic, magnetic, and various gravitational approaches have been examined. Experimental results are presented. The applicabilities of these separation methods are discussed.

Jan 1, 1992

By J. R. Thoenen

[Before 1914 Germany held virtual monopoly on the world supply of potash for fertilizer purposes. During the world War, potash shipments to the United States ceased, and recourse was had to domestic supplies. High war-time prices stimulated interest n various sources, and domestic production increased rapidly. At the close of the war, resumption of shipments from Germany and other sources reduced prices to below pre-war levels, and, as a result, most of the domestic producers ceased operational.]

Jan 1, 1941

By T. M. Yegulalp

A new explanation of the scale dependency of the strength properties of rock is presented based on the theory of extremes. A review of past work on specimen size strength relationship is followed by an introduction to the fundamentals of the underlying theory of extremes and its relationship to the scale effect on the statistical properties of the strength distribution. It is shown that the weakest link theory is directly related to extremal statistics and properties of strength distributions of rock can be derived as a function of the specimen size. Three sets of Brazilian test data are used to demonstrate the use of this approach.

Jan 1, 1992

By Chas. H. Behre

MINING geology, both theoretical and practical, continued to make noteworthy progress during 1938. Mining companies generally, stimulated especially by the improvement in economic conditions during the latter part of the year, extended their workings and developed new ore bodies. Federal and state surveys expanded their search for favorable localities and actual ore bodies, with corresponding enlargement of regional knowledge. Theoretical investigations covered geochemistry of ore deposition, structural control of mineralization, and mineralogy of the ores (chiefly aided by the microscope). More geochemical work is greatly needed: ore searching is still too purely empirical, based on features that have been recognized else- where. Thus, clearer understanding of the conditions essential to transportation of metal salts is needed. Jean Verhogen has suggested that solubilities

Jan 1, 1939

By H. H. Fields, T. W. Goodman, Joseph Cervik

The Bureau of Mines conducted research to determine the effectiveness of long holes drilled in solid virgin coal in degasifying an area of the Pitts- burgh coalbed showing that horizontal holes drilled into a virgin coalbed from the bottom of any shaft will effectively remove methane gas in commercial quantities from the Pittsburgh coalbed. The in situ pressure at a depth of 214 feet into the coalbed and the average gas and water flows from the five degasification holes were 3 lb/in2 gage and 860,000 ft3/d and 1.7 gal/min, respectively. On June 19, 1975, after 593 days of degasification, a compressor was installed and pipeline quality gas was introduced into a commercial pipeline. As of June 1, 1976, after 1,022 days of degasification, over 753 million cubic feet of gas had been drained and 117 million cubic feet of gas had been purchased by the gas company for use in the local community of Wadestown, W. Va. The gas drained to date is six times the gas estimated to be in the area subtended by the holes. Methane emissions at the working face of 1 West mains, Federal No. 2 mine has been reduced by 50 pct, proving the value of methane drainage by horizontal degasification holes drilled from shaft bottoms ahead of mining.

Jan 1, 1976

By P. N. Anyalebechi

"The effects of solidification rate, initial melt hydrogen concentration, and grain refining on porosity formation in aluminum alloy 2024 have been investigated with unidirectionally cooled laboratory-size ingots. The ingots were prepared from melts containing hydrogen concentration of 0.059-0.27 cm3/100 g and solidified at 0.2-37 °C/s. As expected, the amount of porosity, average pore size, and pore number density increased with increase in melt hydrogen concentration and decrease in solidification rate. However, the effect of solidification rate was greater at the very low melt hydrogen concentration (0.059 cm3/100 g). These results are consistent with reported effects of solidification rate and melt hydrogen content on porosity formation in other aluminum alloys. Interestingly, addition of grain refiner slightly increased the amount of porosity and the average pore size, especially at solidification rates above 1°C/s. IntroductionIn shaped castings and wrought products fabricated from ingots, billets, bars, or slabs of aluminum and its alloys porosity formation is a problem. This is because it compromises their tensile strength, fracture toughness, and fatigue properties [ 1-18]. The pores are usually the crack initiation and propagation sites [6,8,9] and the largest pores tend to dictate the fatigue life of the aluminum products [9,10,14]. Porous regions within an aluminum product probably yield first due to the reduced tensile load bearing capacity, causing the concentration of the strain near the voids which subsequently results in premature fracture. In aluminum alloy ingots, billets, bars and slabs porosity formation is particularly problematic because of its persistence through fabrication and potential for reappearance or exacerbation during subsequent thermal treatment processes before and/or after fabrication [19]. In fact, persistence of microporosity is a serious problem in large thick plates of wrought aluminum alloy products that must be rolled from correspondingly large direct-chill or electromagnetic cast ingots. Some of these thick plate products are machined into large aircraft components that are required in service to withstand multi-directional stresses and to possess high fatigue strength, fracture toughness, resistance to stress corrosion cracking, and strength in the short-transverse direction [1,20]."

Jan 1, 2011

By Kara A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature, and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68 °C and 141 °C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large scale experimental configuration, the installation specifications of the fire suppression system, and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature, and limited water application on the suppression system performance.

Jan 1, 2010

By Donald M. Liddell, G. C. RIDDELL

THE cosmic ray continues to engage the attention of the physicists, and according to Millikan and Compton, experiments of the past summer indicate that these rays must come from interstellar space, but not from the stars themselves. According to press reports of the International Congress of Physicists at Rome, the view was given there that these rays have an initiating potential of over 750,000.000 volts. In the field of spectrographic investigation great strides have been made. The U. S. Naval Research Laboratories (R. F. Mehl and G. E. Doan of Lehigh) have just finished a year's work with a "radium torch" or "shadowgraphic apparatus" in the field of the X-ray, that bids fair to displace the latter to a great extent. The torch is more powerful., easier to operate and cheaper. Penetration of 10 in. of steel has been accomplished, which. is much -beyond the- -scope-, of the X-ray..

Jan 1, 1932

By Robert M. Cox

The U. S. Bureau of Mines (USBM) MULSIM/NL modeling technique has been used to analyze anticipated stress distributions for a proposed alternative longwall gate road design for a western Colorado coal mine. The model analyses indicated that the alternative gate road design would reduce stresses in the tailgate entry without increasing stresses in the headgate entry. To test the validity of the alternative gate road design under actual mining conditions, a test section of the alternative system was incorporated into a subsequent set of gate roads developed at the mine. The alternative gate road test section was instrumented with borehole pressure cells, as part of an ongoing USBM research project, to monitor ground pressure changes as longwall mining progressed. During the excavation of the adjacent longwall panels, the behavior of the alternative gate road system was monitored continuously using the USBM computer-assisted Ground Control Management System. During these field tests, the alternative gate road system was first monitored and evaluated as a headgate, and later monitored and evaluated as a tailgate. The results of the field tests confirmed the validity of using the MULSIM/NL modeling technique to evaluate mine designs.

Jan 1, 2010

By Chas. E. van Baraeveld

"The information presented in this report is a by-product of studies concerning zinc, and is published in response to various inquiries for information as to the suitability of zinc for roofing. It parallels a previous report of the Bureau of Mines on slate roofing.Available Forms of Zinc RoofingZinc is available for roofing in three forms: 1. As sheet zinc which may be used advantageously on roofs with as flat a pitch as 1 in 4; laid with standing seam construction for small roofs and with batten construction for large roofs. 2. As corrugate sheets, in widths up to 40 inches and in lengths up to 8 and feet, available for siding and roofing in industrial buildings (with certain re¬strict ions) and or farm buildings (without restrictions). 3. In the form of shingles.Advantages of Zinc Roofing1. Zinc is a permeant roofing material; that is, when suited to the conditions, and properly applied to a roof designed with the right purlin spacing it will outlast the building and still have a salvage value equal to a least half the original material cost. It is applicable to a wide range of conditions, from the most expensive to the cheapest type of construction, and is not greatly above the cheaper materials in first cost. A permanent roof of simple outline need not cost over $15 to $25 per square (100 square feet), depending upon the method of construction required a corrugated sheet roof for industrial purposes or for farm use need not cost over $15 per square for ordinary conditions. 3. Corrugated zinc sheets have the distinct advantage of being available for re-use and re-construction if handled with ordinary care. 4. Zinc oxidizes to a certain point, building up a strong protective coating which in time effectually checks further oxidation; thus it does not oxidize to the point of destruction as steel does, 5. It is light and easily handled."

Nov 1, 1924

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Bolivia has been prepared from the best available information in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State. SYNOPSIS OF LAW All useful substances of the mineral Kingdom belong originally to the State. The soil and subsoil are regarded as two distinct parts, the latter extending indefinitely in depth (Art. 2). The subsoil is under the dominion of the State, which may either abandon it to common use, grant it gratuitously to the owner of the soil, or alienate it, in return for an annual fee, to any individual or association that applies for it. (Art. 1-3.)

Jan 1, 1929

By Shilai Yuan, Huimin Lu, Zhijiang Gao, Panpan Wang

"Solvent refining of silicon through using Si-Al melts is a valid method to remove the impurities from metallurgical grade silicon (MG-Si) melt. The thermodynamic behavior of impurities Fe, Al, Ca, Ti, Cu, C, B and P in MG-Si during the solidification of MG-Si was studied based on the available thermodynamic parameters and experimental data. The morphology of inclusions was investigated by Scanning Electron Microscope (SEM). The chemical composition of inclusions in MG-Si and Al-Si melt was analyzed by EPMA. It is found that the amount of white inclusion reduces and most impurities are solved into the Al-Si melts. After solidification of Si–Al alloy using induction heating and acid leaching, impurities can be effectively removed. The solidification of silicon from the Si–Al melt is found to be more effective for purification than general silicon solidification.IntroductionPhotovoltaic energy is one of promising energy resources in a sustainable society because of its inexhaustibility and cleanliness. Although the production and installation of solar cells have increased significantly during the last decade, the cost of solar cell installation is still high. Multicrystalline silicon has now become the main material in the photovoltaic market because of its low production cost and because of the relative high conversion efficiency of solar cells made from this material, which has been studied for a long time [1-3].Electronic grade (EG) silicon (99.9999999% Si) is commonly used as the raw material to produce SOG-Si (99.9999% Si). Silicon produced from the chemical routes restricts the development of solar cells due to environment threaten, high energy consumption and low productivity. Purification of metallurgical grade silicon (MG-Si) is a low cost, environment friendly method. Although several metallurgical processes such as directional solidification, vacuum refining and electron beam melting [4], have been developed, the cost reduction and refining efficiencies for manufacturing silicon is still have to be further optimized.In the purification process, it is difficult to remove boron and phosphorus by the conventional metal refining method. The refining efficiency depends on the segregation behavior of different elements in solid silicon and the liquid phase. The segregation ratios of all investigated impurities were found to be much smaller than the segregation coefficients between solid and liquid Al-Si melts [5]. For instance, the segregation coefficient of B in Si is 0.8 at the silicon melting point (1687K), whereas it is around 0.2 when silicon is solidified from Si-Al melt at 1273K. For phosphorus the segregation coefficient is 0.06 when silicon is solidified from Si-Al melt at 973K°C, which is much less than 0.35 for recrystallization from liquid silicon. Since the segregation coefficient of boron in silicon is 0.8, it cannot be removed by directional solidification."

Jan 1, 2014