Search Documents

By C. Baldwin Sawyer

During the last half century, much time has been devoted to investigations of the effect of nitrogen on the physical properties of steel, but in all discussions of results there is considerable doubt as to the accuracy and interpretation of analyses. No conclusions concerning the effects of nitrogen on the physical properties of steel can be more reliable than the methods used for determining the quantities of nitrogen present. The work described in this paper endeavors to establish some additional conditions required by the customary distillation method for reliable and nccurate determinations. Results by a combustion method of analysis for total nitrogen content are presented; these indicate that all of the nitrogen in steel, exclusive of that contained in blowholes, may be determined by the distillation method. Based on these more sound and more reliable analyses, results havc been obtained that bear on the following divisions of the general subject, nitrogen in steel: Nitrification of steel by melting in nitrogen, nitrification of steel by heating in ammonia, decomposition of nitrified steel by heating, and thermal analysis of nitrified steel. Consideration of Two Methods of Analysis and Some Results The details of the distillation and combustion methods are chemical in character and of little interest to most readers. They are therefore described in an appendix. The distillation method is essentially that described by Hurum and Fay1 and was generally used throughout this work. It is capable of the greatest accuracy and all results given are significant to the last, figure. Where analyses do not check, the samples

Jan 1, 1923

By C. Baldwin Sawyer

During the last half century, much time has been devoted to investigations of the effect of nitrogen on the physical properties of steel, but in all discussions of results there is considerable doubt as to the accuracy and interpretation of analyses. No conclusions concerning the effects of nitrogen on the physical properties of steel can be more reliable than the methods used for determining the quantities of nitrogen present. The work described in this paper endeavors to establish some additional conditions required by the customary distillation method for reliable and nccurate determinations. Results by a combustion method of analysis for total nitrogen content are presented; these indicate that all of the nitrogen in steel, exclusive of that contained in blowholes, may be determined by the distillation method. Based on these more sound and more reliable analyses, results havc been obtained that bear on the following divisions of the general subject, nitrogen in steel: Nitrification of steel by melting in nitrogen, nitrification of steel by heating in ammonia, decomposition of nitrified steel by heating, and thermal analysis of nitrified steel. Consideration of Two Methods of Analysis and Some Results The details of the distillation and combustion methods are chemical in character and of little interest to most readers. They are therefore described in an appendix. The distillation method is essentially that described by Hurum and Fay1 and was generally used throughout this work. It is capable of the greatest accuracy and all results given are significant to the last, figure. Where analyses do not check, the samples

Jan 1, 1923

By Paul Summers, Kevin Richardson, Willem (Billy) Villet, Paul J. Sabatini, Edward C. Clukey

"Between 2008 and 2009, more than 6,000, 23-m long deep mixing method (DMM) elements were constructed to support 124 concrete mats comprising the foundations for the process trains for an LNG facility. The Owner requested first-of-its-kind analyses and assessments to confirm the quality and reliability of the DMM foundation. This paper provides information on these assessments and the procedures used to ultimately conclude that a fit-for-purpose foundation system was constructed.During early phases of construction, several DMM test cores revealed nodules of unmixed clay in upper core samples. A comprehensive review of available DMM core information was undertaken. It was concluded that the amount of coring being conducted as part of the contractor’s QA/QC program should be increased to achieve a foundation system with the required level of reliability.Three-dimensional finite element analyses were completed considering various distributions of defects in the DMM elements and the effects of potential downdrag on DMM elements. Calculated mat settlements and mat stresses were compared to cases without defects in the DMM elements. Various distributions of loaded and unloaded mat areas and number and position (both in the subsurface and laterally) of defects were considered. Four (of the 124) mats were identified as potentially “at-risk”. The settlement performance of these mats is currently being monitored and, to date, performance has been acceptable.IntroductionThe foundation support system for the process train at a major LNG facility comprises more than 6,000, 23-m long DMM elements. The general subsurface stratigraphy at the project site comprises (from the ground surface): (i) up to 8 m of fill sand initially placed underwater building to a stable construction platform; (ii) up to 12 m of soft organic clay (Unit II clay); and (iii) clayey sand and sand layers becoming progressively denser with depth (Unit III sands). Each DMM element comprised two secant 1.5-m diameter DMM columns. DMM elements were typically arranged as cells enclosing one, two, or three DMM elements."

Jan 1, 2017

By P. Zhang

A multiyear, comprehensive study of flotation reagents used in phosphate beneficiation was conducted. The study involved the evaluation of pure fatty acid compounds, comparison of various anionic collectors and testing of iso-acids. Various C12 to C22 fatty acids were tested as Florida phosphate collectors. The saturated fatty acids were found to be very poor collectors when using the standard conditioning procedure, whereas the unsaturated C16 to C22 fatty acids showed fair to good phosphate collecting ability. The C18 fatty acids oleic, impure oleic and linoleic and the C20 eicosenoic acid were shown to be the best phosphate collectors. The best flotation results were obtained using Liqro GA tall oil and oleic acid. Four isostearic/iso oleic acid type fatty acid collectors were compared with a commercial grade oleic acid and with Liqro GA tall oil as phosphate collectors using standard laboratory conditioning and flotation procedures. The most selective collector evaluated was Century 1108, a high isostearic acid-type reagent. However, it was concluded that this excellent-performing reagent was too expensive for commercial use. Overall, the most promising reagent was probably Century MO-5. This collector is essentially an iso-oleic acid/stearic acid mixture (not isostearic acid), and it costs much less. This program laid a sound foundation for developing single collector, all anionic flotation processes.

Jan 1, 2009

By H. A. Pearse

NORMALLY, the Britannia ore mixture contains chalcopyrite and pyrite as the chief sulfide minerals, together with minor amounts of gold and silver and a low zinc content. Reduction is accomplished by jaw crushers underground, followed at the concentrating plant by Symons cone crushers, rolls, and ball mills. The standard flotation practice, evolved during several years of experimentation, provided for bulk flotation of the two sulfides, after primary grinding to only approximately 35 mesh, followed by regrinding of the bulk concentrate, with subsequent separation of the chalcopyrite and pyrite to make a marketable concentrate of each mineral. This so-called standard milling practice has previously been described in detail in U. S. Bureau of Mines Information Circular 6619. A modification will he discussed here. In the face of a constantly increasing world surplus of copper and a steadily falling price during 1930 and 1931, it was obviously undesirable to continue unprofitable production of large quantities of this metal. On the other hand, company officials were

Jan 1, 1934

By J. G. Walters

This bulletin presents, in collected and tabluated form, Bureau of Mines and American Gas Association (EM-AGA) carbonization data pertaining to the chemical analysis of tars and the characterization of tars and light oils obtained from U.S. coals.

Jan 1, 1967

By A. L. Engel

Production of chromite in California has been from many small, high-grade mines. The opening of the Purchase Depot at Grants Pass, Oreg., in 1951 has stimulated chromite mining in California, and a large number of properties are being reexamined as there is a possibility that some low-grade ores from many of these properties can be beneficiated to meet the purchasing schedule. The Bureau of Mines in its program of conservation is continuing ore-dressing tests on chromite ores to better evaluate their potential. This report is a compilation of preliminary concentration tests on samples from five different properties in California. The concentration tests were made on ores from the David mine, Butte County, the Seiad Creek mine, Siskiyou County, the High Plateau mine, Del Norte County, Bud's mine, Tuolumne County, and tailings from the Miller concentration plant in San Luis Obispo County, Calif., to determine the possibility of beneficiating these ores so that they will meet the specifications for the Government stockpile.

Jan 1, 1956

By M. Ramachandran, R. G. Reddy

"A direct route for the reduction of magnesium oxide to magnesium using thermal plasma processing, with methane as the reducing gas, has been systematically evaluated. A feasibility study of the reduction reaction has been performed on the MgO-CH4 system at different methane concentrations and temperatures. The effects of changes in the key process parameters, such as the oxide-to-methane ratio and plasma power, on the yield of magnesium have been systematically evaluated. A maximum yield of about 61 mol% Mg was obtained using power of 20.0 kW and a molar ratio of MgO:CH4=1:1. Phase, morphological, elemental and binding energy analyses were performed on the product powders to understand the reduction reaction. Surface oxidation was observed in smaller magnesium particles in all the experiments, while the in-situ sintering of magnesium rods was observed at a molar ratio of MgO:CH4=1:1.5. Magnesium carbide (Mg2C3) was observed in the product, and its mechanism of formation is proposed using phase equilibrium data and a predominance diagram.IntroductionMagnesium has an excellent combination of low density and high strength. These properties have increased worldwide demand for and use of magnesium. Two major processes are used in the commercial synthesis of magnesium metal. The first method is electrolytic reduction and the second is thermal reduction using Pidgeon process. These processes can be classified as traditional techniques, but there are numerous emerging technologies that aim at reducing the production cost of Mg, its environmental impact and energy consumption. Thermal plasma processing is one emerging technique that has great potential in all the abovementioned key areas of magnesium production.Traditional reduction techniques. Two major reduction techniques, namely electrolytic and thermal reduction, have been used in the commercial production of magnesium. Electrolytic reduction is typically carried out in electrolytic cells from magnesium chloride (obtained from seawater or well and lake brines) (Tripp, 2009). The following simplified reaction shows the reduction of magnesium chloride to liquid magnesium and chlorine gas:"

Jan 1, 2015

By Industrial Research Office

"The U.S. Bureau of Mines established on August 15, 1983, the Generic Mineral Technology Center for Respirable Dust within the Mining and Mineral Resources Research Institutes (MRIs) at The Pennsylvania State University and West Virginia University in association with participating MRIs at Massachusetts Institute of Technology and the University of Minnesota. The Center's research program has been developed with recognition of the stated objective of the Federal Mine Safety and Health laws which is to ""... permit each miner the opportunity to work underground during the period of his entire adult working life without incurring any disability from pneumoconiosis or any other occupation-related disease . . . ."" The Center's program is designed to permit an accelerated attack on the fundamental research problems for the control of respirable dust in mines.The primary goal of the Center is to reduce the incidence and severity of respirable dust disease through advancing the fundamental understanding of all aspects of respirable dust associated with mining and milling and the interaction of dust and lungs. The Generic Technology Center's research program explores these concerns with the objective of refining existing strategies and developing new respirable dust control techniques that are consistent with the fundamental dust-lung interaction processes that lead to mine worker disability. The work concentrates on: (1) control of dust generation; (2) dilution, dispersion and collection in mine airways; (3) characterization of dust particles; (4) interaction of dust and lungs; and (5) relationship of mine environment, geology, and seam characteristics to dust generation and mobility. The fundamental aspects of this work are applicable to the control of respirable dust problems in both hard rock mines and coal mines and to other dusts such as diesel-generated. The Center activities involve the training of engineers and scientists, graduate students and undergraduate students through their respective institutions, and the technology transfer to the industry. The Center also serves as the reference center for publications' in the respirable dust area.The Center is composed of faculty from the four universities/institutes listed above. The personnel, facilities and equipment that are available to the Center from these entities are diverse, complementary and comprehensive. More than fifty scientists, engineers; and medical personnel in the Center are engaged in respirable dust research. Additionally, the expertise and facilities of the NIOSH--Division of Respirable Disease Studies are available as a result of the existing relationship between NIOSH and West Virginia University.The breakdown of the dust research program into the five areas mentioned above recognizes the importance of an integrated fundamental research approach to the respirable dust problem compatible and complementary with the existing and ongoing U.S. Bureau of Mines activities. The specific projects in the research areas are a result of a careful evaluation of the past and ongoing research activities, the identification of areas where data and information are scarce, and awareness of the recommendation of the National Academy of Sciences Study on the Measurement and Control of Respirable Dust. Penn State is the administrative unit for the Center. Funding to date is nearly $6.5 million."

Aug 31, 1989

By Theodore H. Boggs

The battle of the gold standard is not limited to one country alone, or even to a single group of countries. It is being waged merrily in many important commercial and industrial quarters. Though it is not always a practical issue calling for immediate attention, it is none the less, quite widely, engaging the thought of bankers and other students of finance. The controversy arises, in the last analysis, because of the desire of men to secure a stable currency. There are two ways of restoring a reasonably stable currency system: (1) the re-establishment of the gold standard, or (2) the deliberate and artificial management of a paper currency. Both systems are well known. The gold standard was in use prior to the war in the principal commercial countries. A currency of inconvertible paper has been at times employed in the past in various countries; for example in Britain from 1797 to 1821, and in the United States from 1862 to 1879. The gold standard, as all are aware, implies the selection of gold as the standard of value. The unit of value is a fixed weight of gold and, so long as the standard remains unimpaired, all other means of payment are maintained at a parity with standard gold coins. And gold coins alone constitute the standard money, inasmuch as their value as bullion equals their value as coins. Under the gold standard this would not be true of any other form of money, although all other varieties of money, including bank notes, government notes and silver coins would be freely convertible into gold money. Strictly speaking, the gold standard also implies that the gold money in turn shall itself be freely convertible, through melting, into gold bullion and freely exportable.

Jan 1, 1925

By S. W. Jacobsz, Y. Narainsamy

Several high-impact tailings dam failures around the world in recent years have placed a renewed focus on the stability of tailings dams and pointed to potential shortcomings in traditional drained design and safety evaluation procedures. A need to consider undrained shear strength in the design of tailings facilities has become apparent. However, there are specific requirements that need to be met before undrained shearing occurs. In South Africa, the last major failure was likely the Merriespruit disaster in 1994, which leads to the question of whether the conditions required for undrained shearing are readily applicable to South African tailings dams. This paper describes research at the University of Pretoria that has recently commenced to further investigate the conditions required for undrained failure to occur. The research includes laboratory and field testing to replicate these conditions in the laboratory and relate them to those found in an active tailings dam.

Jun 2, 2022

By J. L. Carne

ORE control is a matter of planning and supervision based on a foreknowledge of the content and distribution of ore. The Inspiration orebody is predominately a copper-sulphide blanket, overlain by an oxidized zone of copper silicates, copper carbonates, and barren capping. Most of the ore is treated by leaching, and the optimum requirement of this method is the goal toward which the mining schedule is aimed. Both open-pit operations and underground mining are used. The problems of ore control at Inspiration are: 1-maintenance of metallurgical balance, 2-conservation of oxide ore, and 3-mining out of the orebody at an average grade which parallels that of the reserve figure. Prior to the fall of 1926 all of the Inspiration division ores were treated by flotation, but the mixed ores of the Live Oak-Keystone section carried too large a proportion of copper in the form of chrysocolla for satisfactory flotation. For this type of mixed ore the leaching process now in use had been worked out, and the plant was put into operation in the fall of 1926. The process is known as the ferric sulphate leach, and the leaching solvents contain both ferric sulphate and free sulphuric acid. Sulphide copper in the form of chalcocite is leached by the ferric sulphate, and the oxidized copper minerals are dissolved by the sulphuric acid. From the beginning of operations to the present time the plant has treated some 67 thousand tons of ore having an average copper content of 1.142 pet, of which 0.605 pct has been in the form of oxidized copper minerals. The plant is currently being operated at the rate of 11,500 tons per day, 7 days per week. However, this tonnage is produced in 6 days of mine operation. The average current grade is approximately 1 pct copper, of which about 50 pct is present as oxidized or acid-soluble copper. Close control of metallurgical procedures is a vital factor in operation of the plant and is in turn dependent upon careful regulation of feed. An excess of sulphide copper requires the presence of more ferric sulphate in the leaching solvents. On the other hand, an excess of ferric sulphate in the presence of a low sulphide feed seriously reduces the efficiency of electrolytic precipitation in tank house operations. This condition must be avoided at all costs. An additional factor must be considered. It is known that the sulphide content is predominant in the ore which remains in the reserve. To maintain the necessary sulphide-oxide proportion, so that the entire reserve will mine out at both a grade and a sulphide-oxide ratio that will be permissible throughout the remaining life of the property, it is obvious that the oxide reserve must be currently preserved to as great an extent as possible. Fortunately much of the oxide reserve is found in the open-pit operation. This happy circumstance adds flexibility to the procedure and makes it possible to maintain the close regulation necessary to insure best overall results, both mining and metallurgical. The two ore streams from the pit and underground operations join at the coarse-crushing plant, and proper control must be exercised before the ore reaches this point. The open pit is currently providing about 55 pet of the ore and underground operations the balance of production. Both operations are under a single superintendent so that the closely interrelated problems may be more readily controlled. The least flexible of the two producing units is the underground mine, where the mining method is block caving. Although a block of ground may be undercut and developed, characteristics of the material determine its caving action. The ore in the chutes must be drawn. The area currently mined from underground is in a zone predominately sulphide and is generally

Jan 1, 1952

By M. E. Karabin, R. J. O'Malley

"A mathematical model of the roll casting process has been developed which predicts macro-variables, such as roll separating force, roll torque, and strip exit speed for a range of roll speeds. Continuum variables, such as interface pressure, interface shear stress, freeze-front shape, and internal temperature distribution are also predicted.The model consists of two independent segments: solidification and rolling. The solidification model is two-dimensional (thickness and rolling direction) and is capable of handling alloy solidification. The solidification model is employed until solidification through the thickness is complete, then the rolling solution is activated.The rolling model is a one-dimensional (rolling direction) mechanical solution based on the von Karman approach, coupled with a two-dimensional thermal solution. The flow stress is expressed as a function of the average through-thickness temperature of the strip.Experiments were performed using a laboratory roll caster to test and refine the model. Experimental strip exit temperatures were used as input to the model. Experimental and predicted roll torque and strip exit speea were forced into agreement at a single reference roll speed to obtain values for the coefficient of friction and the interfacial heat transfer coefficient. Using these values, good agreement was obtained between predicted and experimental torque and strip exit speed over the entire range of roll speeds examined."

Jan 1, 1986

By A. P. Page, G. E. Alexander, L. L. Sirois, A. A. Winer

A knowledge of the electrical surface characteristics of minerals is all-important in the choice of treatments to up-grade and beneficiate them. At their solid-liquid contacts, there are transfers of ionic species, which for insoluble oxide minerals are the H+ and OH-ions. The adsorption density of these ions can be detected by carrying out potentiometric titrations, and this paper describes the automation of such an apparatus. The details are discussed fully and the validity of the method is demonstrated by flotation tests.

Jan 1, 1969

By D. Stone, N. J. Aslin, W. Webb

In today's modem copper electro-refineries, increasingly higher average current densities are being employed. With these increases many refineries are approaching their limiting current density. The nearness of the average operating current density to the limiting current density has placed increasing emphasis on the need to maintain an even current distribution. This paper explores the importance of maintaining even current density and discusses the factors, processes and practices that are necessary to achieve and maintain high quality production at high operational intensity.

Jan 1, 2005

By R. Hogg, S. Chander

"The distribution of the wettability of coals of different rank was determined by measurements of contact angles for individual particles. The contact angle was estimated from the equilibrium partitioning of a particle at the water/air interface. Using this technique contact angles were determined for a larger number of particles from a given sample and a frequency distribution of contact angle was obtained. The contact angle distribution was broad for all the coals tested with included an anthracite, a hvA bituminous and a sub-bituminous coal. In comparison, spherical particles of polymethylmethacrylaie gave a much narrower distribution. The distribution for irregular polyethylene particles was somewhat broader than that for the polymethylmethacrylate spheres but broader than that for the polymethylmethacrylate spheres but considerably narrower than that for coal. The broader wetting distribution for coal was attributed to differences in surface chemical properties.INTRODUCTIONA knowledge of the wetting properties of coals is very useful in coal cleaning by flotation and other processes in which separations are based on differential surface properties. The various methods available for measuring wetting characteristics include: contact angle, 1-2 time, time, 3-5 bubble attachment, 6 film flotation,7 displacement pressure, 8-9 penetration rate, 10-11 bubble pick-up, 12 induction time, 13 imbibition time, 14 and calorimetry. 15-16 Of all these methods, however, the measure¬ment of contact angle by the sessile drop and captive bubble techniques have been most widely used. Brady and Gauger"" demonstrated through the use of the contact angle method that the natural hydrophobicity of coal varied greatly from sample to sample. Subsequent experiments showed that this difference correlated well with rank, the larger contact angles generally being associated with the higher rank coals. 18-19 More recent studies by Aplan and co-workers' show that the wettability of various ranks of coals as determined by sessile drop and captive bubble methods is a more complex function of rank. The hydrophobicity of coal usually increases with rank up to about 80% fixed carbon (dmmf) and then decreases."

Mar 1, 1992

By Hye-Sung Kim, Dong-Wha Kum, Gyeungho Kim

"Mechanical alloying is an effective way to finely distribute inert dispersoids in AI-TM (TM is a transition metal element) systems. It is considered that high melting point aluminides are formed by precipitation from the supersaturated aluminum matrix. The analysis is based on the fact that much higher content of TM than the solubility limit can be dissolved in alpha aluminum during the high energy ball milling. Nonetheless, the role of undissolved TM particles affecting the formation of aluminides is not suitably considered. In this paper, authors present experimental observation on the formation of Ab3Ti particles from mechanically alloyed AI-Ti alloys in the hyper-peritectic region. This study showed that, in the mechanically alloyed AI-20wt%Ti specimen, intermediate phase of cubic Ab3Ti and tetragonal AIz4Tis formed at 300 - 400°C and 400 - 500°C, respectively, before the MA-state reaches to the global equilibrium at higher temperatures. The formation behavior of Lh- Ab3Ti is interpreted by interdiffusion of Al and Ti in solid state based on the fact that large amount of nano-sized Ti particles exist in the milled powder. Present analysis indicated undissolved Ti particles of nanosize should have played an important role initiating the formation of Ab3Ti phase during annealing.IntroductionInterest in the hyper-peritectic AI-Ti alloys is based on industrial demand for high-modulus and high-temperature aluminum alloys. Earlier works on hyper-peritectic AI-Ti alloys with 4 to 12wt%Ti show that these alloys are strong at ambient temperature and maintain high strength above 300°C when titanium-trialuminide (e.g., Ab3Ti) is finely distributed in the aluminum matrix [1,2]. High melting point and high stiffness with low density of AbTi make the AI-Ti alloys strong with greater thermal stability while keeping weight savings as much as possible. Titanium in aluminum shares other merits of transition metal additions because Ti solubility in Al is low (i.e., 1.l5wt%Ti at 665°C and virtually zero below 400°C), and fine dispersion of Ab3Ti particles is readily accomplished and resists grain coarsening effectively."

Jan 1, 1996

By Rudy Scarabelli, John R. Wagner

At one time explosives were the only economical means of rock tunnel excavation. Except in relatively long tunnels in the right rock explosives are still the cheapest means of rock excavation where they can be used. Today the most economical means of rock tunnel excavation is increasingly not the choice of the contractor. A good part of our work is for public agencies in urban areas and the public today is increasingly less tolerant of the disruption caused by our efforts. Owners in many cases have to direct their engineers to write specifications which severely restrict noise and vibration levels during construction. Sometimes specifications allow drill-and-shoot for starter tunnels only or even eliminate powder by fiat. Recent advances in the use of explosives such as sequential firing have made blasting more palatable to the public but are not enough in all situations. Thus the roadheaders on construction projects. In recent work I have seen the Alpine Miners, a Paurant Miner and the Robbins Mobile Miners used in several rock formations and now believe this type of equipment has a place in the tunnel constructor's choice of equipment. Rudy and I have not attempted to present a formula for choosing the best alternative excavation method in any given case because, of course, of the variables involved. We have simply tried to describe our experiences on a particular project and hope our observations will be of some value to tunnel constructors.

Jan 1, 1987

By Ray D. Peterson

The hydrothermal enrichment of chalcopyrite by CuSO, occurs in the absence of oxidizing or reducing reagants. Kinetics of the enrichment process were determined under autoclave conditions in the temperature range of 398°K (125°C) to 473°K (200°C). Covellite (CuS) formed first, followed by digenite (Cu,,,S), with rejection of iron to the solution. The kinetics have been explained by a model which includes diffusion during the first stage formation of covellite followed by surface reaction rate control when digenite be. The effects of particle size, temperature, pH, and cupric and ferrous ion concentrations on the leaching kinetics were examined. Additions of ferrous ion to solution markedly increased the rate of reaction.

Jan 1, 1994

By C. E. McElroy

"INTRODUCTION The ventilation of working places in mines by jets of air discharged from fan-pipe lines is an important phase of mine ventilation, whether the primary purpose is to dilute gas or dust concentrations or to provide air-motion cooling effect. Jets of similar nature are very prominent factors in the ventilation of enclosed spaces, such as buildings and ships. The effectiveness of such jets depends on the distribution of the air in the jet streams, a subject on which the little definite information previously available applied to jet discharge into large, open spaces under conditions quite different from those ordinarily associated with fan-pipe discharge in mines.The results of an initial series of experiments on the discharge of air from fan-pipe lines in mine openings have been described. 3/ This report presents the results of a second series of experiments and compares the results of both series with theory and experiment on jet discharge into large, open spaces. The results of this second series confirm and supplement those of the initial series, in which a 10-inch pipe discharged into an 8- by 8-foot develop¬ment end through seven short discharge pieces of different designs. In the present series the same 10-inch line was used, but the discharge was through 10- to 30-foot lengths of 5-inch, 10-inch, and 20-inch-diameter pipes and through a 20-foot length of 29- by 3-inch pipe. Tests were made with the air discharged into a closed drift or development end, as in the previous series (in which case the discharged air returned past the end of the pipe) and into an open drift (in which case the discharged air did not return past the end of the pipe but continued out along the drift). Test conditions corresponded to the discharge of a jet into a channel closed at one end; in one case, the discharge was directed toward the closed end and in the other toward the open end. The former typifies fan-pipe ventilation of development ends and the latter an abrupt increase in the sectional area of an airway. In both the flow had to pass from jet to open air against some resistance.The tests were made in the Mount Weather Testing Adit of the Bureau at Bluemont, Va., on the pipe line installed for ventilating the adit, and extended from late September to mid-November 1940. Preparations were made for directly comparable series of experiments on the injector effect of fan-pipe discharge in an open drift and on free expansion in large, open spaces, but these test programs were .first postponed in favor of other work and finally abandoned until the war is over."

Nov 1, 1943