Search Documents

By R. L. Hills

America's industry uses about 44% of the total energy consumed by the nation directly as fuel burned in industrial plants or indirectly as fuel burned by utilities to provide electric power. In addition, industry requires raw materials or feed stocks derived from fuel sources or having fuel value. This represents about 11% of total U. S. energy consumption, bringing industry's portion to about 55%. Adding that portion of energy consumption required by the transportation sector to move raw materials, intermediates, and finished products, the total energy impact of industry approaches 213 of total U. S. consumption. It is obvious that American industry has the largest share in the task of balancing energy demand and supply. What are we going to do? -- We must increase the supply of energy and increase the beneficial results obtained from each unit expended. Both avenues, unfortunately, are limited in extent and speed. Increases in supply cannot occur without drastic and permanent increases in cost. These increases in cost are un- desirable and inflationary but do provide incentive for the rational businessman to expend the effort and money required to improve the effectiveness of energy in industry.

Jan 1, 1975

By Oliver Bowles

Wire saws have been used for many years in European travertine, marble, and slate quarries. This method of sawing found very limited use in America until 1927 when it was accepted as standard equipment in elate quarries in Pennsylvania where it has been remarkably successful. Details of its operation in slate have been published in a recent bureau report.3 The very limited extent to which the wire saw has been employed in limestone and marble quarries in the United States and the seeming lack of interest even in experimental work to determine its advantages are difficult to explain in vied of its wide use in cutting similar rocks in Europe and its unquestionable advantages in sewing slate in America. In order to encourage improvement in quarry practice the United States Bureau of Mines has endeavored to obtain information as to the extent to which wire saws are used in Europe together with data on the rate and cost of sawing. The information at hand is by no means complete either in territory covered or in details of operation; it nevertheless brings out certain significant features that may be of interest and advantage to quarrymen in the United States.

Jan 1, 1931

By G. Winkel

Safety conditions in industry have greatly improved over time. However, around the world, in Canada, and in each province or territory, people are still the victims of serious industrial accidents. The increasing safety of people at work then continues to be an imperative in industry today.<p> So how do we achieve a workplace where no one gets hurt? Well, in simple terms, folks need to be protected from unplanned exposures to equipment or energy sources that can do harm. If you think about it, all of our efforts in loss management and safety should then be directed toward avoiding these uncontrolled events. And it works! Our safety performance over the years has enjoyed tremendous improvement due to this support for loss management and safety. We now explore best practices toward achieving that next step in safety improvement.<p> As shown following, a large combination of loss management activities act together to support safety performance. Many of these activities are interrelated and some people have described them as the ?inputs? into an approach or program for achieving safety. Using this description, it follows that the ?outputs? of the program are some of the advertised measures of safety we see around us today, such as injury frequency rates. <p> It is asserted that a leadership focus to regularly measure safety and loss management activites (so-called ?inputs?), as a basis for taking supportive actions to ensure their effectiveness, is the basis for safety results (so-called ?outputs?) that consistently achieve high standards of excellence.<p> The concept of managing input activities, as enabled by effective measurements, can significantly act to transform our focus and priorities in the workplace. Supporting input activities like strategies, plans, or procedures with our best efforts will get us to our intended goals. Tracking outputs alone will not.<p> Safety and production have traditionally been cast as competing objectives. When both objectives are mutually supported and considered, however, people will invent ways of doing work that support both safety and production, and any other business parameter. When done right, innovation through meaningful involvement of affected people in the workplace will support safety excellence in a manner that in turn improves business efficiency overall.<p> For a workplace to be safe, it then requires everyone?s help and participation to make it happen, a collaborative effort by management, leaders, and frontline folks with the power and responsibility to take appropriate action at every level in the organization. In this way, everyone becomes a leader in safety.<p> The achievement of commitment to loss management input activities by folks in the workplace is the basis for attaining safety excellence. A workplace founded on commitment supports a safety culture with a vision for safe work performance at outstanding or world-class levels of achievement.<p> One may ask if injury incidents will be eliminated with this commitment and focus on workplace safety? Well, despite our best efforts in this area, there is never a guarantee that things can?t go wrong. We are simply not perfect. There remains in our workplace complexities and unanticipated risks that can have disastrous consequences if not managed at every moment. And when it goes wrong, we need to know we?ve truly tried our best, and now we have more to learn so we can get even better. <p> That?s the challenge represented by the safety imperative, a challenge to take safety performance that next step, a fulfillment of our commitment to the moral obligation we have to each other?s safety. It?s an effort that will continually raise the bar of world-class safety performance achievement for future generations. It?s a legacy we can be proud to be part of.

Sep 1, 2004

By Rodolfo Lagos, Nicos Pfeiffer, Ben Harding, Clayton V. Deutsch

This paper documents a probabilistic resource modeling workflow for the Round Mountain epithermal gold deposit. The set of categorical and continuous variable simulated realizations provides a model of variability and uncertainty given the current orebody knowledge. These realizations can be used to quantify and understand expected deviations in reconciliation during mining and provide a more accurate measure of expected gold than an estimated model. Gold mineralization at Round Mountain is primarily contained within tertiary tuff units, which dip gently to the west and thicken towards the southern part of the orebody. Domain boundaries are modeled as combinations of lithology and alteration; alteration domains are constrained to be within the tuffs. Large-scale geologic uncertainty is strongly influenced by parameter uncertainty, particularly the input histogram. The spatial bootstrap characterizes prior global uncertainty in the input histogram for categorical and continuous variables. Categorical models are generated using hierarchical truncated pluri-Gaussian (HTPG) simulation. Continuous variable simulation is carried out within the simulated domain boundaries using trend models to account for non-stationarity.

Aug 19, 2023

By J. N. Van der Merwe, M. Mathey

"The development and mechanical characterization of coal-crete, a composite material generated from coal fragments and some binder material, is described in this paper. Coal debris was obtained from a colliery in South Africa. The binder used in the study basically consists of cement and water, and further ingredients are added to the mixtures, such as sand, fly ash and polymers, in order to investigate alterations of the mechanical properties of coal-crete.Results from over 220 mechanical tests on coal-cretes with various binder mixtures give consistent trends for the material’s behaviour. Linear relationships are suggested between the uniaxial compressive strength, Young’s Modulus and the indirect tensile strength of the coal-crete.It is shown that mechanical properties comparable to coal can be achieved. Coal-crete is therefore suitable for physical modelling of mining situations in experimental studies and for use as backfill in underground coal mines. The latter application is particularly attractive when refuse coal is used as aggregate material. The indicated trends in this study may be used as a guideline for individual coal-crete design needs. However, some uncertainty remains as to the influence of particle shape, size and gradation, coal rank and age of the coal-crete. These aspects are recommended for further research."

Jan 1, 2015

By Rudá Grossi Coimbra Martins

A estruturação organizacional da gestão da informação em Central de Serviços já está consolidada no ambiente de Tecnologia da Informação. O ambiente de Tecnologia de Automação compartilha características semelhantes, já que também fornece serviços para seus clientes. Entretanto, serviços de automação possuem particularidades derivadas, em grande parte, do fato de que são mais críticos para a atividade fim da empresa, já que visam manter a operação. Implantar uma Central de Serviços em ambiente de Tecnologia de Automação de uma empresa já existente demanda uma série de modificações em termos de Tecnologias, Processos e Pessoas para trazer os retornos desejados em termos de gerenciamento, organização da rotina e disponibilidade dos ativos. Este trabalho apresenta alternativas para atuar sobre os três componentes supracitados durante a implantação de uma Central de Serviços, com foco em sua operação através de uma Gestão Compartilhada (Cosourcing). Experiências adquiridas em projetos de especificação e operação de Central de Serviços também são apresentadas para embasar a estruturação da gestão da informação em ambiente de Tecnologia da Automação de indústrias de Metais e Mineração.

Jul 30, 2018

By Robert Boutilier

For more information on what the social licence means, see the following: Joyce, S. and Thomson, I. 2000. Earning a social licence to operate: Social acceptability and resource development in Latin America. The Canadian Mining and Metallurgical Bulletin, 93(1037) Nelson, J. and Scoble, M. 2006. Social License to Operate: Issues of Situational Analysis and Process. Vancouver, BC: Department of Mining Engineering, University of British Colombia. Thomson, I. and Boutilier, R.G. 2010. The Social License to Operate In P.Darling, (Ed.), SME Mining Engineering Handbook: Littleton, CO: Society for Mining, Metallurgy and Exploration. Much of what has been written and said about the social license to operate focuses on what the company has to do or not do. But the social license is a two-sided relationship. We also need to look at what the community has to do, or not do, in order to be capable of issuing a social license that is meaningful.

May 1, 2010

By H. H. Fields

The Bureau of Mines conducted research to determine the effectiveness of long holes drilled in solid virgin coal in degasifying an area of the Pittsburgh coalbed showing that horizontal holes drilled into a virgin coalbed from the bottom of any shaft will effectively remove methane gas in commercial quantities from the Pittsburgh coalbed. The in situ pressure at a depth of 214 feet into the coalbed and the average gas and water flows from the five degasification holes were 3 lb/in2 gage and 860,000 ft3/d and 1.7 gal/min, respectively. On June 19, 1975, after 593 days of degasification, a compressor was installed and pipeline quality gas was introduced into a commercial pipeline. As of June 1, 1976, after 1,022 days of degasification, over 753 million cubic feet of gas had been drained and 117 million cubic feet of gas had been purchased by the gas company for use in the local community of Wadestown, W. Va. The gas drained to date is six times the gas estimated to be in the area subtended by the holes. Methane emissions at the working face of 1 West mains, Federal No.2 mine has been reduced by 50 pct, proving the value of methane drainage by horizontal degasification holes drilled from shaft bottoms ahead of mining.

Jan 1, 1976

By H. W. Wainwright

1. A schematic diagram and a description of the apparatus are presented. 2. Five runs were made using gas having a hydrogen-carbon monoxide ratio of about 2:1 and sulfur concentrations ranging from nil to 1.53 grains per 100 std. c.f. 3. At constant space velocity of synthesis gas the product of the sulfur concentration and days of operation, with conversion of H2 + CO above 97 percent, was constant. With a gas containing 0.04 grain of sulfur ac carbonyl sulfide per 100 std, cu. ft ,, the conversion of H2 + CO remained over 97 percent for 40 days. During that time the heating value of the product gas (on a C02-free basis) remained relatively constant at 940 B .t .u. per c.f., based on dry gas measured at 600 F. and 30 inches Hg.

Jan 1, 1954

By A Fyans, B Ghahreman-Nejad

This paper discusses the method and results of an options study into selection of the optimal form for a 130 m high tailings/water retaining dam, located in a region of high seismicity in central Iran. The proposed dam is part of a planned expansion project for Sarcheshmeh Copper Mine (SCM), which after construction will provide 550 million tonnes of additional tailings storage over the next 27 years. Geotechnical investigation at the proposed site indicated that adequate suitable low permeability materials (i.e. clay) were not available in the immediate vicinity of the dam site and would need to be imported from a distance of well over 10 km (direct). Given the magnitude of the estimated quantity of material and construction cost it was considered prudent to compare the cost of alternative dam design options for the proposed storage. A total of five dam design options are considered including a conventional rockfill embankment dam with an upstream sloping earth core (ECRD), a geomembrane face rockfill embankment dam (GFRD), a sloping asphalt core rockfill embankment dam (ACRD), a roller compacted concrete dam (RCCD), and a filter rockfill embankment dam for tailings storage together with a separate smaller earthfill core rockfill dam (ECRD) located downstream for storage of decant water. The risks, costing and design of all options are discussed in detail and the outcome of the study is presented.CITATION:Ghahreman-Nejad, B and Fyans, A, 2018. Optimum embankment design for a tailings dam, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 427–438 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Andrew Mackenzie, Paul Rantala

Data is now appearing in literature that indicates many current paste fill systems in Canada suffer from plugged lines and severe wear rates. Both of these conditions suggest: design problems with the pipe distribution system, backfill composed of poorly graded material and/or possibly poor operator practices. Problems that can be prevented in the design stage, but still may be readily solvable with current technology. However, if left untreated will lead to an increasing frequency of down time. The compatibility of the distribution system with the paste fill rheology is fundamental and essential for the reliable delivery of fill. Either many mine operators are not familiar enough with the technology to provide a critical review that could foresee problems down the road, prior to construction and or North American designers are not clarifying their designs to their customers. The objective of this paper is to highlight key concepts to mine operators with the purpose of better enabling a critical review of contractor&apos;s/consultant&apos;s designs. There is a great deal of understanding about the rheology of backfill over a range of pulp densities from hydraulic slurry to dense to paste. However, outside of deep mines (especially in South Africa) neither hydraulic or dense fill distribution systems have suffered the problems of paste fill. Paste fill is fundamentally different from hydraulic fill principally in its transportation characteristics. These differences have a direct impact on the design of the distribution system. By understanding the practical implications of these differences the operator can play a more active role in their design while better appreciating how to best operate their own system.

Jan 1, 2001

By R. K. Sinha, B. S. Choudhary, Desh Deepak, A. K. Mishra, Hemant Agrawal, Shankar Kumar

There are several methods (empirical, statistical, and machine learning tools) to calculate blast-induced ground vibration. Still, due to complications in the blasting procedure, under varying blasting loads and strata conditions, it is not easy to predict and simulate blast vibration precisely. Therefore, a study was conducted to simulate the field blast data in Ansys software using explicit dynamics. For this study, monitoring of ground vibration for 20 single hole blasts was carried out. The density of emulsion explosives was in the range of 0.9 to 1.15 g/cc. In the laboratory, rock properties were determined from the rock sample collected from the mine site before blasting. The in-hole velocity of detonation (VoD) and the density of the emulsion explosive were also determined. These parameters were used for numerical analysis to know the ground vibrations at specified points. The results of ground vibration predicted by the model are validated using field data.

By L. E. K. Holappa

Iron and steel making plays a significant role in global energy consumption and carbon dioxide emissions. The target of limiting the global warming by 2050 is extremely challenging for this energy-intensive branch of industry. In order to be responsible for its own share in cutting CO2 emissions, great advancements must be done. A brief history, present situation and different scenarios are discussed. Possibilities to decrease CO2 emissions in current processes via improved energy efficiency, alternative process routes, energy sources and recycling are examined. On-going and planned efforts and programs of steel producers and institutions, as well as trends of energy generation in the long run are reviewed and evaluated.

Mar 1, 2017

By Renate Wellen, Olgun Guven, Mariane Y. T. Oide, Julyana Satana, Francisco Valenzuela-Díaz, Esperidiana Moura

Poly[(ethylene)-co-(vinylacetate)] (EVA) is a thermoplastic copolymer composed of randomly distributed polyethylene and polyvinyl acetate sequences within the molecular chain. EVA combines toughness with excellent flexibility, impact and puncture resistance. Because of these properties, this material is largely used for foam production as padding in equipment for various sports and as a shock absorber in sport’s shoes. This work aims to study the influence of clay reinforcement on the performance of recycled polymer foams. The blend containing recycled HDPE (high density polyethylene) and recycled EVA (70/30 wt%, respectively) reinforced with 2 wt%of clays were prepared by melt extrusion, using a twin-screw extruder to obtain the composites. The composites and foaming agent were fed into a special single screw extruder for foaming. The samples of HDPE/ EVA/Clay foams were characterized by tensile test, Field Emission Scanning Electron Microscopy (FE-SEM), Thermogravimetric Analysis (TG), Differential Scanning Calorimetry (DSC), X-ray Diffraction (XRD), density measurement and the correlation between the results was evaluated.

Mar 1, 2018

By Bo Liang, Hongmin Zhu, Kai Huang, Shafiq Alam

A new approach of recovering platinum and palladium from electronic wastes by hydrochloric acid leaching followed by selective adsorption on low-cost and environmentally benign biomass sorbent prepared from easily available agriculture waste is suggested. The obtained adsorbents were prepared by a combination of chemical modification and hydrothermal carbonization process with (NH4)2C2O4. It was found that the maximum adsorption capacity of hydrothermal carbonized garlic peel for Pt( ) and Pd( ) was 1.64 and 0.42 mol/kg respectively. The Langmuir adsorption isotherm was applied to describe the adsorption process. Kinetics of the Pt( ) and Pd( ) ions adsorption was found to follow pseudo-second-order rate equation. The adsorbents were examined by scanning electron microscope (SEM), and Fourier transform infrared spectroscopy (FT-IR). Based on the characterization results, a possible mechanism of Pt( ) and Pd( ) ions adsorption with the hydrothermal carbonized garlic peel was proposed. This study provides a promising adsorbent with efficient adsorption property for platinum and palladium recovery from the leach solution of electronic wastes.

Jan 1, 2016

By P. H. Mell

THE little village, from which this formation receives its name, is situated on a bluff of the Alabama River, 175 feet above water level. This bluff is a portion of high table land that begins in the western portion of Choctaw and extends through Clarke and Monroe counties. We find points on this ridge more than 100 feet higher than Tuscaloosa, and nearly as high as the Tennessee River at Tuscumbia. Through this the Alabama River cuts its way, exposing a beautiful cross-section of the strata, of which the accompanying sketch may give some idea. The fossils are found about 75 feet below the surface and 100 feet above the level of the river. There are seven distinct strata. 1. The lowest, extending from the water&apos;s edge up the bluff 80 feet, is a soft calcareous rock containing about 15 per cent. of carbonate of lime, with occasional specks of mica. In this a few Ostrea, Turritellce, and Flustrce were found, but so friable as to fall to pieces when handled. 2. Next comes a stratum varying from 2 to 8 feet, consisting of

Jan 1, 1880

By V 9. 0 / 300 dpi

In the time period from the early 1980&apos;s to the present, longwall roof support technology has evolved tremendously. Chock supports and caliper shields were replaced by 2-leg or 4-leg lemniscate shields. The lemniscate linkage for which the support is named offers numerous advantages to the sup-port both as a fabricated structure and to its performance in the mining application. The hydraulic system, which is the dynamic element of the roof support, was essentially unchanged in early lemniscate shields with the exception of the complexity of additional hydraulic circuits to power a canopy tilt cylinder and canopy side-seals. The control of these fluid-powered functions was provided by direct manual control of valves energizing individual functions onboard the roof-support or the adjacent roof-support. This control valve-gear was comprised of multiple individual valves arranged in a "bank" or integrated into a single hydraulic distribution block with a single operating handle to select any independent function.

Jan 1, 1993

By JOHN R. SUMAN

IT appears now that the conflict with the totalitarian states will be a long-drawn-out struggle. The course of this war up to now indicates that this may well be the first major conflict where man power has not been the vital and determining factor. Mechanized warfare has made it possible for relatively small, well-equipped groups to outmaneuver and defeat large armies which lack the necessary modern equipment. Under these circumstances, ultimate victory becomes a matter of resources and productive ability. The important question is not how many soldiers can he put into the field, but the volume and speed in producing the armaments essential to ensure a victory. The resources available to the opposing nations and the efficiency of their systems of enterprise and production will be primary factors in determining the ultimate outcome. Germany had a head start of eight years in the armament race, and it is not easy to overcome such an advantage overnight.

Jan 1, 1942

By Jon C. Volkwein

The Bureau of Mines conducted a series of tests to evaluate the effectiveness of mixing a compressed-air-generated foam with dried whole-grain silica sand to suppress dust in minerals processing plants. Dust at downstream transfer points was monitored with personal gravimetric samplers and with Real-Time Aerosol Monitors (RAM&apos;s) that were connected to strip&apos; chart recorders. Results showed dust reductions of 80 to 90 pct on three separate occasions at two different plants. The mechanism by which foam suppresses dust is discussed, as are the constraints on the use of foam, which may include incompatibility of the foam with the mineral product, difficulty in controlling the foam generator, and cost.

Jan 1, 1983

By Stephen Mansfield, Johannes Schoeman

In August 2006 a technical alliance was formed between Orica Mining Services and Century Mine to provide blasting solutions. The alliance is in the form of a Rock to Specification (R2S™) service, one of Orica’s Blast Based Services (BBS™). The ultimate goal was to facilitate the rapid expansion of material movement from 26 to 41M m3 (34 to 53M yd3) per annum while maintaining a reliable ore supply to the mill.

Jan 1, 2010